Ford 2006 Five Hundred v.3- Manuals

SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? Inthis guide, answers to such questions are contained in commentshighlighted by the warning triangle symbol. These comments should beread and observed. Warning symbol...

SPECIAL NOTICES New Vehicle Limited Warranty For a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited Warranty, refer to the Warranty Guide that is provided to you along with your Owner’s Guide. Service Data Recording Service data recorders in your v...

Special instructions For your added safety, your vehicle is fitted with sophisticated electroniccontrols. Please read the section Supplemental restraint system (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

Check fuel cap (if equipped): Illuminates when the fuel cap maynot be properly installed. Continueddriving with this light on may causethe Check engine warning light tocome on, refer to Fuel filler cap in the Maintenance and Specification chapter. Brake system warning light: To confirm the brake sys...

Speed control: Illuminates when the speed control is engaged. Turnsoff when the speed control systemis disengaged. Low washer fluid (if equipped): Illuminates when the windshieldwasher fluid is low. Door ajar (if equipped): Illuminates when the ignition is inthe ON position and any door ordecklid is...

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, the engine is overheating. Stopthe vehicle as soon...

AUDIO SYSTEMSAM/FM stereo/ single CD sound system (if equipped) Accessory delay: Your vehicle is equipped with accessory delay. With this feature, the window switches and radio may be used for up to tenminutes after the ignition is turned off or either front door is opened. 1. / Tuner: Press to manu...

When the six strongest stations are filled, the station stored in preset 1will begin playing. If there are less than six strong stations, the systemwill store the last one in the remaining presets. Bass: Press to adjust the bass setting. Use / / SEEK . Treble: Press to adjust the treble setting. Use...

GENERAL AUDIO INFORMATION Radio frequencies: AM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio and TelecommunicationsCommission (CRTC). Those frequencies are: AM: 530, 540–1700, 1710 kHz FM: 87.7, 87.9–107.7, 107.9 MHz Radio reception factors:...

Audio system warranty and service Refer to the Warranty Guide for audio system warranty information. If service is necessary, see your dealer or qualified technician. Navigation system (if equipped) Your vehicle may be equipped with a Navigation System. Refer to the Navigation supplement for further...

2. PLAY/PAUSE control Press to playback or pause the DVD. 3. DIM control Press (+) to increase or (-) to decrease the brightness on the screen. 4. ENTER control Press to select the function highlighted on the active menu. ENTER mayalso be used by some user interactive discs during movie play. 5. MEN...

• Press the NEXT control to movethe cursor one position upward • Press the PREV control to movethe cursor one position downward • Press the REV control to movethe cursor left one position • Press the FWD control to movethe cursor right one position Next/Previous control The NEXT (up) and PREV (down)...

Remote control 1. REV (REVERSE) control Press to reverse the direction of the DVD movie. 2. FWD (FORWARD) control Press to advance the direction of the DVD movie. 3. PLAY/STOP control When playing, press PLAY/STOP to stop the disc. When stopped, pressPLAY/STOP to play the disc. 4. SEEK control Press...

3. Dimmer switch. Press +/- to increase/decrease the brightness of thedisplay. Playback and format • The DVD player of your Family Entertainment DVD System can onlybe used in the “playback” mode. (The DVD player does not offer arecord feature.) • The system plays standard CDs, DVDs and also plays mo...

• If the Family Entertainment System (FES) is playing and the ignitionis turned OFF, the system will turn off, and suspend playback. Whenthe ignition is turned on again, playback will begin from the lastselected media source when the play control is pressed. • To disable the DVD player rear controls...

2. Connect the left and right audio lines to the WHITE (left) and RED(right) auxiliary input jacks respectively. 3. Press the MODE control repeatedly until DVD/CD AUX (no disc inplayer) or DVD/CD play (disc in player) illuminates in the radio display.If a disc is in the system, playback should begin...

Safety information Read all the safety and operating instructions before operating thesystem and retain for future reference. • Do not attempt to service, repair or modify the Family EntertainmentDVD System. See your Ford or Lincoln Mercury dealer. • Do not insert foreign objects into the DVD compar...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Temperature selection: Controls the temperature of theairflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in thevehicle. See the following for a briefdescription on each control setting: MAX A/C: Distributes...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL(IF EQUIPPED) 1. Defrost: Distributes outside air through the windshield defroster and demister vents. Can be used to clear thin ice or fog from thewindshield. To exit select another mode. 2. Passenger temperature control: Press to increase/decrease the airflow...

Dual Zone Automatic Temperature Control with heated seats(if equipped) 1. Defrost: Distributes outside air through the windshield defroster and demister vents. Can be used to clear thin ice or fog from thewindshield. To exit select another mode. 2. Passenger temperature control: Press to increase/de...

Operating tips • To reduce fog build up on the windshield during humid weather, placethe air flow selector in the position. • To reduce humidity build up inside the vehicle: do not drive with theairflow selector in the OFF or with recirculated air engaged. • Do not put objects under the front seats ...

REAR WINDOW DEFROSTER R The rear defroster control is located on the climate control panel andworks to clear the rear window of fog and thin ice. The ignition must be in the 3 (RUN) position to operate the rear windowdefroster. The rear defroster turns off automatically after 10 minutes or when thei...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the headlamps on. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the hea...

5. Wait the desired amount of time for the exit delay you want (up tothree minutes), then turn the headlamp switch to . The headlamps will turn off. High beams Pull the lever towards you, to thesecond detent, to activate. Pull thelever towards you again todeactivate. Flash to pass Pull toward you, t...

Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the ON position, • the headlamp control is in the OFF, autolamps or parking lampposition and • the transmission must be out of the Park position. Always remember to turn on ...

TILT STEERING WHEEL To adjust the steering wheel: 1. Pull down and hold the steeringwheel release control. 2. Move the steering wheel up ordown until you find the desiredlocation. 3. Pull the steering wheel releasecontrol up. This will lock thesteering wheel in position. Never adjust the steering wh...

Storage compartment Press the latch to open the storagecompartment. The door will openslightly and can be moved to fullopen. The storage compartment may beused to secure sunglasses or asimilar object. CLOCK (IF EQUIPPED) Press and release the button toadjust forward. Press and hold to fast forward. ...

• Rear vent (if equipped) Use only soft cups in the cupholder. Hard objects can injure youin a collision. AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only. Do not insertany other object in the power outlet as this will damage theoutlet and blow the fuse. Do not hang ...

When closing the power windows, you should verify they are freeof obstructions and ensure that children and/or pets are not in the proximity of the window openings. Press and pull the window switchesto open and close windows. • Push down (to the first detent)and hold the switch to open. • Pull up (t...

Window lock The window lock feature allows onlythe driver to operate the powerwindows. To lock out all the window controlsexcept for the driver’s press theright side of the control. Press theleft side to restore the windowcontrols. Bounce-Back (Driver’s window only) When an obstacle has been detecte...

AUTOMATIC DIMMING INSIDE REAR VIEW MIRROR (IF EQUIPPED) Your vehicle may be equipped withan inside rear view mirror with anauto-dimming function. Theelectronic day/night mirror willchange from the normal (highreflective) state to the non-glare(darkened) state when bright lights(glare) reach the mirr...

Heated outside mirrors (if equipped) Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated. Do not remove ice from themirrors with a scraper orattempt to readjust the mirrorglass if it is frozen in place.These actions could causedamage to the glass ...

Do not use the speed control in heavy traffic or on roads thatare winding, slippery or unpaved. Setting speed control The controls for using your speedcontrol are located on the steeringwheel for your convenience. 1. Press the ON control and releaseit. 2. Accelerate to the desired speed. 3. Press th...

• Depress the brake pedal or pressCNCL (Cancel) until the desiredvehicle speed is reached, pressthe SET + control. Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal or pressCNCL (Cancel). This will noterase your vehicle’s previously setspeed. • Pre...

In Radio mode: • Press SEEK to access thenext/previous strong station. In CD mode: • Press SEEK to listen to the nexttrack on the disc. In any mode: • Press VOL up or down to adjustthe volume. • Press MUTE to mute the volume. MOON ROOF (IF EQUIPPED) You can move the glass panel of the moon roof back...

detect an object, signaling the door to stop and reverse, does not meetcurrent U.S. federal safety standards. For more information, contactHomeLink 威 at: www.homelink.com or 1–800–355–3515. Retain the original transmitter for use in other vehicles as well as forfuture programming procedures (i.e. ne...

4. The indicator light will flash slowly and then rapidly. Release bothbuttons when the indicator light flashes rapidly. (The rapid flashing lightindicates acceptance of the hand-held transmitters’ radio frequencysignals.) 5. Press and hold the just-trained HomeLink 威 button and observe the indicato...

• Continue to press and hold the HomeLink 威 button (note Step 3 in the “Programming” section) while you press and release — every two seconds (“cycle”) your hand-held transmitter until the frequency signal has been accepted by the HomeLink 威 . The indicator light will flash slowly and then rapidly a...

2. The indicator light will begin to flash after 20 seconds. Withoutreleasing the HomeLink 威 button, follow Step 2 in the “Programming” section. For questions or comments, contact HomeLink 威 at www.homelink.com or 1–800–355–3515. MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position,the ...

System warnings System warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems. In the event of a multiple warning situation, the message center willcycle the display to show all warnings by displaying each one for severalseconds. The message center will display th...

DRIVER’S DOOR AJAR. Displayed when the driver’s door is not completely closed. PASSENGER DOOR AJAR. Displayed when the passenger side door is not completely closed. LEFT REAR DOOR AJAR. Displayed when the left rear door is not completely closed. RIGHT REAR DOOR AJAR. Displayed when the right rear do...

An oil change is required whenever indicated by the message center andaccording to the recommended maintenance schedule. USE ONLYRECOMMENDED ENGINE OILS. To reset the oil monitoring system to 100% after each oil change[approximately 5,000 miles (8,000 km) or 180 days] perform thefollowing: To reset ...

KEYS One key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed keywill not permit your vehicle to start. If you lose your authorized dealersupplied keys, replacement keys are avail...

1. Place the key in the ignition and turn the ignition to the 3 (RUN)position. 2. Press the power door unlock control on the door panel three times. 3. Turn the ignition from the 3 (RUN) position to the 1 (LOCK) position. 4. Press the power door unlock control on the door panel three times. 5. Turn ...

Press to automatically move the seat, mirrors and adjustable pedals to the desired memory position (the positions correspond to the transmitterbeing used). Note: You can associate a specific remote entry transmitter to each memory position. For more information on programming thetransmitters to Driv...

How to reprogram your remote entry transmitters You must have all remote entry transmitters (maximum of four) available before beginning this procedure. Note: Ensure the brake pedal is not depressed during this sequence. To reprogram the remote entrytransmitters: 1. Ensure the vehicle is electronica...

• after 25 seconds of illumination. The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. Battery saver The battery saver will shut off the interior lamps 30 minutes after theignition has been turned to the 1 (LOCK) position. • If the dome...

KEYLESS ENTRY SYSTEM You can use the keyless entrykeypad to: • lock or unlock the doors withoutusing a key. • open the trunk. • recall memory seat/powermirrors/adjustable pedalspositions 1 or 2. The keypad can be operated withthe factory set 5–digit entry code;this code is located on the owner’swall...

3. Enter factory–set 5–digit entry code. 4. Press and hold the 7 • 8. While holding the 7 • 8 press the 3 • 4. 5. Release the 3 • 4. 6. Release the 7 • 8. The user should receive a horn chirp to indicate the system has been disabled or a chirp followed by a honk to indicate the system has beenenable...

If a problem occurs with the SecuriLock 娂 system, the indicator will flash rapidly or glow steadily when the ignition is in the 3 (RUN) position. Ifthis occurs, the vehicle will not start and should be taken to anauthorized dealer for service. Automatic arming The vehicle is armed immediately after ...

PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will help prevent your vehicle fromunauthorized entry. If there is any potential perimeter anti-theft problem with your vehicle,ensure ALL remote entry transmitters are brought to the authorized dealer to aid in troubleshooting. Ar...

• Press the 7 • 8 and 9 • 0 controls on the keyless entry padat the same time to lock thedoors (driver’s door must beclosed). There is a 20 second countdownwhen any of the above actions occurbefore the vehicle becomes armed. Each door, the hood or the trunk isarmed individually, and if any areopen, ...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Before returning the seatback to...

Push release button to lower headrestraint. Using the manual lumbar support (if equipped) The lumbar support control islocated on the outboard side of theseatback. Move the control up or down toadjust lumbar support. Folding down the front passenger seatback The front passenger seatback can befolded...

Cover sharp edges on the load to help prevent injury tooccupants. Secure the load to help prevent shifting during sudden stops. Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatback. After returning the seatback to its original...

Pull lever up to adjust seatback. Before returning theseatback to its original position, make sure that cargo orany objects are not trappedbehind the seatback. Afterreturning the seatback to itsoriginal position, pull on theseatback to ensure that it has fullylatched. An unlatched seat maybecome dan...

A position can be recalled: • in any gearshift position if the ignition is not in the RUN position. • only in P (Park) or N (Neutral) if the ignition is in the RUN position. A memory seat position may be programmed at any time.The memory positions are also recalled when you press your remoteentry tr...

SAFETY RESTRAINTS Personal Safety System 姟 The Personal Safety System 娂 provides an improved overall level of frontal crash protection to front seat occupants and is designed to helpfurther reduce the risk of airbag-related injuries. The system is able toanalyze different occupant conditions and cra...

(child size) occupants from airbag deployments when they areimproperly seated or restrained in the front passenger seat contrary toproper child-seating or restraint usage recommendations. Even with thistechnology, parents are STRONGLY encouraged to always properly restrain children in the rear seat....

position sensor, and passenger occupant classification sensor. In addition,the RCM also monitors the restraints warning light in the instrumentcluster. A difficulty with the system is indicated by one or more of thefollowing. • The warning light will either flash or stay lit. • The warning light wil...

In a rollover crash, an unbelted person is significantly more likelyto die than a person wearing a seat belt. Each seating position in your vehicle has a specific safety beltassembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on the...

if your vehicle receives an impact of 5 mph (8 km/h) or more, the safetybelt will become locked and help reduce your forward movement. Energy Management Feature — Front Outboard • This vehicle has a safety belt system with an energy managementfeature at the front seats to help further reduce the ris...

BeltMinder 姞 The BeltMinder 威 feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders byintermittently sounding a chime and illuminating the safety belt warninglight in the instrument cluster when the driver’s and front passenger’ssafety belt...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... “Crashes are rare events” 36700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be ser...

Reasons given... Consider... “I have an airbag” Airbags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety be...

Safety belt extension assembly If the safety belt is too short when fully extended, there is a 8 inch (20cm) safety belt extension assembly that can be added (part number611C22). This assembly can be obtained from an authorized dealer. Use only extensions manufactured by the same supplier as the saf...

All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even when an air bag supplemental restraint system (SRS) is provided. Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints. National Hig...

Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. Airbags can k...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

• diagnostic module. • and the electrical wiring which connects the components. The diagnostic module monitors its own internal circuits and thesupplemental airbag electrical system wiring (including the impactsensors), the system wiring, the airbag system readiness light, the airbagback up power an...

The front passenger sensing systemuses a ⬙ passenger airbag off ⬙ or ⬙ pass airbag off ⬙ indicator which will illuminate and stay lit to remind youthat the front passenger frontal airbag is disabled. The indicator lamp islocated above the glove box on the instrument panel. Note : The indicator lamp ...

In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit. If the airbag readiness lamp is lit, do the following: The driver and/or adult passengers should check for any objects thatmay be lodged underneath the front passenger ...

A difficulty with the system is indicated by one or more of the following: • The readiness light (same lightfor front and side airbag system)will either flash or stay lit. • The readiness light will notilluminate immediately after ignition is turned on. • A series of five beeps will be heard. The to...

How does the side airbag system work? The design and development of the side airbag system includedrecommended testing procedures that were developed by a group ofautomotive safety experts known as the Side Airbag Technical WorkingGroup. These recommended testing procedures help reduce the risk ofin...

If the Safety Canopy 娂 system has deployed, the Safety Canopy 娂 will not function again unless replaced. The Safety Canopy 娂 system (including the A, B, and C pillar trim) must be inspected and serviced by an authorized dealer. If the Safety Canopy 娂 is not replaced, the unrepaired area will increas...

must put them in safety seats made especially for children. Many statesrequire that children use approved booster seats until they are eightyears old. Check your local and state or provincial laws for specificrequirements regarding the safety of children in your vehicle. Whenpossible, always place c...

Move a child to a different seating location if the shoulder beltdoes not stay positioned on the shoulder during use. Follow all instructions provided by the manufacturer of thebooster seat. Never put the shoulder belt under a child’s arm or behind theback because it eliminates the protection for th...

8. Allow the safety belt to retract toremove any slack in the belt. 9. Before placing the child in theseat, forcibly move the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the seat at the belt pathand attempt to move it side to sideand forward. There should ...

2. Route the child safety seat tether strap over the back of the seat. For vehicles with adjustable head restraints, route the tether strap underthe head restraint and between the head restraint posts, otherwise routethe tether strap over the top of the seatback. 3. Locate the correct anchor for the...

Attaching safety seats with LATCH (Lower Anchors and Tethers forChildren) attachments for child seat anchors Some child safety seats have two rigid or webbing mounted attachmentsthat connect to two anchors at certain seating positions in your vehicle.This type of child seat eliminates the need to us...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperatu...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing the tire’sresistance to the gene...

Use a tire gauge to check the tire inflation pressure, including the spare(if equipped), at least monthly and before long trips. You are stronglyurged to buy a reliable tire pressure gauge, as automatic service stationgauges may be inaccurate. Ford Motor Company recommends the use ofa digital or dia...

To check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from drivingeven a mile. If you are checking tire pressure when the tire is hot, (i.e. driven morethan 1 mile [1.6 km]), never “bleed” or reduce air pressure. The tires arehot from driving and it is norm...

cracking, cuts, bruises and other signs of damage or excessive wear. Ifinternal damage to the tire is suspected, have the tire demounted andinspected in case it needs to be repaired or replaced. For your safety,tires that are damaged or show signs of excessive wear should not beused because they are...

If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. Do not spin the wheels at over 35 mph (56 km/h). The tires mayfail and injure a passenger or bystan...

3. 65: Indicates the aspect ratio which gives the tire’s ratio of height to width. 4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheeldiameter. 6. 95: Indicates the tire’...

13. Maximum Permissible Inflation Pressure: Indicates the tire manufacturers’ maximum permissible pressure and/or the pressure atwhich the maximum load can be carried by the tire. This pressure isnormally higher than the manufacturer’s recommended cold inflationpressure which can be found on the Saf...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires youcurrently have on your vehicle. The tires on your vehicle have all weather treads to provide traction inrain and snow. However, in some climates, you may need to use snowtires and chains. Follow these guidelines when us...

your vehicle’s weight ratings, with or without a trailer, from the vehicle’sTire Label or Safety Compliance Certification Label: Base Curb Weight – is the weight of the vehicle including a full tank of fuel and all standard equipment. It does not include passengers, cargo, oroptional equipment. Vehi...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehi...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the B-Pillar or the edge of the driver’s door. The totalload on each axle must never exceed its GAWR....

If you use a rental trailer, follow the instructions that the rental agencygives to you. Do not attach safety chains to the bumper. Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes aresafe if installed properly and adjusted to the manufacturer’sspecifications. The tr...

• Allow more distance for stopping with a trailer attached. • If you are driving down a long or steep hill, shift into the “L” gearposition. Do not apply the brakes continuously, as they may overheatand become less effective. • The trailer tongue weight should be 10–15% of the loaded trailerweight. ...

STARTING Positions of the ignition 1. LOCK, locks the automatictransaxle gearshift lever and allowskey removal. This position also shutsthe engine and all electricalaccessories off without locking thesteering wheel. To lock the steeringwheel, remove the key then turn thesteering wheel. 2. ACC, allow...

• Make sure the gearshift lever is inP (Park). 3. Turn the key to 3 (RUN) withoutturning the key to 4 (START). Some warning lights will briefly illuminate. See Warning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine 1. Turn t...

Guarding against exhaust fumes Carbon monoxide is present in exhaust fumes. Take precautions to avoidits dangerous effects. If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important ventilating information If ...

Four-wheel anti-lock brake system (ABS) Your vehicle is equipped with an Anti-lock Braking System (ABS). Thissystem helps you maintain steering control during emergency stops bykeeping the brakes from locking. Noise from the ABS pump motor andbrake pedal pulsation may be observed during ABS braking ...

Parking brake Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops. The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released....

To help avoid personal injury, always use caution when in R(Reverse) and when using the RSS. This system is not designed to prevent contact with small ormoving objects. The system is designed to provide a warning to assist the driver in detecting large stationary objects to avoid damagingthe vehicle...

The RSS automatically turns onwhen the gear selector is placed inR (Reverse) and the ignition is ON.An RSS control on the instrumentpanel allows the driver to turn theRSS on and off. To turn the RSS off,the ignition must be ON, and the gear selector in R (Reverse). Anindicator light on the control w...

AWD Systems (if equipped) AWD uses all four wheels to powerthe vehicle. This increases traction,enabling you to drive over terrainand road conditions that aconventional two-wheel drive vehiclecannot. Sand When driving over sand, try to keep all four wheels on the most solidarea of the trail. Avoid r...

when you are driving over sand, apply the accelerator slowly and avoidspinning your wheels. If the vehicle does slide, steer in the direction ofthe slide until you regain control of the vehicle. If the transmission, AWD system components or axles are submerged inwater, their fluids should be checked...

Maintenance and Modifications The suspension and steering systems on your vehicle have been designedand tested to provide predictable performance whether loaded or emptyand durable load carrying capability. For this reason, Ford MotorCompany strongly recommends that you do not make modifications suc...

ROADSIDE ASSISTANCE Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the...

Canadian customers refer to your Owner Information Guide forinformation on: • coverage period • exact fuel amounts • towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and ...

HAZARD FLASHER CONTROL The hazard flasher is located on theinstrument panel by the radio. Thehazard flashers will operate whenthe ignition is in any position or ifthe key is not in the ignition. Push in the flasher control and allfront and rear direction signals will flash. Press the flasher control...

FUSES AND RELAYS Fuses If electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check the appropriatefuses before replacing any electricalcomponents. Note: Always replace a fuse with one that has the specified amperage r...

Passenger compartment fuse panel/Smart Junction Box (SJB) The fuse panel is located under the instrument panel to the left of thesteering wheel. The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description F1 20A High beams F2 15A Interior lamps (C...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description F8 15A Park lamps, Side markers, Trailertow protect F9 20A Cigar lighter, Data Link Connector(DLC) F10 7.5A Mirrors and memory module F11 20A Audio, Family EntertainmentSystem (FES) F12 10A Back-up lamps, Electrochromat...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description F23 7.5A Wiper relay coil, Blower relay coil,Cluster logic F24 7.5A Occupant Classification Sensor(OCS), Passenger Air bagDeactivation (PAD) C1 30A Circuit breaker Delayed accessory (Frontpassenger window, Rear passenge...

For vehicles equipped with 4WD, it is not recommended that the vehiclebe operated in 4WD modes with a temporary emergency spare tire. If4WD operation is necessary, do not operate above speeds of 10 mph (16km/h) or for distances above 50 miles (80 km). 3. Full-size dissimilar spare without label on w...

Removing the spare tire and jack 1. Lift the trunk cargo cover, andremove the wing nut that securesthe spare tire by turning itcounterclockwise. 2. Lift and remove the spare tirefrom the trunk. 3. Remove the second wing nut thatsecures the jack retention bracketby turning it counterclockwise,remove ...

Stowing the tire and jack 1. Fully collapse the jack, fold thelug wrench socket into the handleand place the jack and wrench intothe felt bag as shown. Take care toposition the jack as shown to ensurethat the locating holes in the jackbase can be placed on the locatingtabs of the jack mounting brack...

If you are stowing the temporaryspare tire, place the tire over the jack and secure it with the largewing nut. WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque at 100 miles (160 km)after any wheel disturbance (tire rotation, changing a flat tire, wheelremoval, etc.)...

Do not attempt to push-start your vehicle. Automatictransmissions do not have push-start capability; doing so maydamage the catalytic converter. Preparing your vehicle When the battery is disconnected or a new battery is installed, thetransmission must relearn its shift strategy. As a result, the tr...

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second ...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Remove the jumper cable on the negative (...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM(U.S. ONLY) Your satisfaction is important to Ford Motor Company and to your dealer.Experience has shown that our customers have been very successful inachieving satisfaction by following the three-step procedure outlined onthe front page of the Warr...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformation is subject to change, please ask your authorized dealer forcomplete details about Ford Extended Service Plan coverage options, orvisit the Ford ESP ...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which isavailable from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

WAXING Applying Motorcraft Paint Sealant (ZC-45) to your vehicle every sixmonths will assist in reducing minor scratches and paint damage. • Wash the vehicle first. • Do not use waxes that contain abrasives; use Motorcraft PremiumLiquid Wax (ZC-53-A), which is available from your authorized dealer,o...

ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. Thehigh-pressure fluid could penetrate the sealed parts and causedamage. • Do not spray a hot engine with ...

WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, substances on thevehicle’s glass or the wiper blades may be the cause. These may includehot wax treatments used by commercial car washes, water repellan...

Do not use chemical solvents or strong detergents when cleaningthe steering wheel or instrument panel to avoid contamination of the airbag system. • Be certain to wash or wipe your hands clean if you have been incontact with certain products such as insect repellent and suntanlotion in order to avoi...

LEATHER SEATS (IF EQUIPPED) Your leather seating surfaces have a clear, protective coating over theleather. • To clean, use a soft cloth with Motorcraft Deluxe Leather and VinylCleaner (ZC-11–A). Dry the area with a soft cloth. • To help maintain its resiliency and color, use the Motorcraft DeluxeLe...

SERVICE RECOMMENDATIONS To help you service your vehicle we provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer canprovide the necessary parts and service. Check your Warranty Guide/Owner Informati...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood. 3. Lift the hood and support it withthe prop...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16-A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

To prolong the life of the wiper blades, it is highly recommended toscrape off the ice on the windshield before turning on the wipers. Thelayer of ice has many sharp edges and can damage the micro edge of thewiper rubber element. ENGINE OIL Checking the engine oil Refer to the scheduled maintenance ...

• If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added to raise the level within thenormal operating range. • If required, add engine oil to theengine. Refer to Adding engine oil in this chapter. • Do not ...

4. Install the indicator and ensure it is fully seated. 5. Fully install the engine oil filler cap by turning the filler cap clockwiseuntil it stops. To avoid possible oil loss, DO NOT operate the vehicle with theengine oil level indicator and/or the engine oil filler cap removed. Engine oil and fil...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trouble-free operation, keep...

Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing ofacid solution. In case of acid contact with skin or eyes, flushimmediately with water for a minim...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interv...

Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine...

1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the coolant reservoir (an opaque plastic bottle).Slowly turn cap counterclockwise (left) until pressure begins to release. 3. Step back while the pressure...

If you have to add more than 1.0 quart (1.0 liter) of engine coolant permonth, have your authorized dealer check the engine cooling system.Your cooling system may have a leak. Operating an engine with a lowlevel of coolant can result in engine overheating and possible enginedamage. Recycled engine c...

• Decreased engine coolant concentrations below 40% willdecrease the freeze protection characteristics of the enginecoolant and may cause engine damage. • Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperature...

Refueling Fuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep spa...

If you must replace the fuel filler cap, replace it with a fuel fillercap that is designed for your vehicle. The customer warranty maybe void for any damage to the fuel tank or fuel system if thecorrect genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If...

Octane recommendations Your vehicle is designed to use“Regular” unleaded gasoline withpump (R+M)/2 octane rating of 87.We do not recommend the use ofgasolines labeled as “Regular” thatare sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes kno...

• The indicator may come on. For more information on the “check engine” or the “service engine soon” indicator, refer to Warning lights and chimes in the Instrument Cluster chapter. ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you,...

• Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers). 2. Each time you fill the tank, record ...

Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test ofthe on-board diagnostics system. If the indicator is on, refer to the description in the Warning lights and chimes section of the Instrument Cluster chapter. Your vehicle may no...

BRAKE FLUID The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“MAX” lines are within the normaloperating range; there is no need toadd fluid. If the fluid levels areoutside of the normal operatingrange the perfor...

Items Ford PartName orequivalent Ford PartNumber FordSpecification Coupler fluid VolvoTransmissionOil, Clutch 1161641 — Power TransferUnit (PTU)fluid MotorcraftSpecialty PowerTransfer UnitFluid XY-75W90–PTU — Engine oil Motorcraft SAE5W-20 PremiumSynthetic BlendMotor Oil (US)Motorcraft SAE5W-20 Supe...

The Vehicle Identification Number (VIN) contains the followinginformation: 1. World manufacturer identifier 2. Brake system / Gross VehicleWeight Rating (GVWR) / RestraintSystem 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence nu...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local Ford or Ford of Canada dealer. These qualityaccessories have been specifically engineered to fulfill your automotiveneeds; they are custom designed to complement th...

A Accessory delay ..........................63 Air cleaner filter .......................259 Air conditioning ....................42, 44 Airbag supplemental restraintsystem ........................123, 132, 134 and child safety seats ............125description ..............123, 132, 134disposal ......