Ford 2005 Freestyle v.3- Manuals

SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? Inthis guide, answers to such questions are contained in commentshighlighted by the warning triangle symbol. These comments should beread and observed. Warning symbol...

SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and 6.0LPower Stroke Diesel Engine Coverage. In addition, your vehicle is eligiblefor Emissions Defect and Emissions Performance Warranties. For adetai...

Special instructions For your added safety, your vehicle is fitted with sophisticated electroniccontrols. Please read the section Supplemental restraint system (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -No...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause extensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

Check fuel cap: Illuminates when the fuel cap may not be properlyinstalled. Continued driving withthis light on may cause the Checkengine warning light to come on,refer to Fuel filler cap in the Maintenance and Specification chapter. Brake system warning light: To confirm the brake system warninglig...

Parking brake ON: Sounds when the parking brake is left ON and driven. If the warning stays on after the park brake is off, contact yourdealer as soon as possible. GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At norma...

AM/FM STEREO/ SINGLE CD SOUND SYSTEM (IF EQUIPPED) 1. / Tuner: Press to manually go up or down the radiofrequency. Also use in menu modeto select various settings. 2. Phone/mute: Press to mute the playing media. Press again to returnto the playing media. 3. Menu: Press to toggle through the followin...

14. Seek: Press to access the previous strong station or track. 15. AM/FM: Press to select AM/FM frequency band. 16. ON/OFF/Volume: Press to turn ON/OFF. Turn to increase/decreasevolume.If the volume is set above a certainlevel and the ignition is turned off,the volume will come back on at a“nominal...

FAMILY ENTERTAINMENT DVD SYSTEM (IF EQUIPPED) Your vehicle may be equipped with a Family Entertainment DVD Systemwhich allows you to watch DVDs, play music CDs, and to plug in andplay video game systems. Please review this material to become familiarwith the Family Entertainment System (FES) feature...

4. ENTER control Press to select the function highlighted on the active menu. ENTER mayalso be used by some user interactive discs during movie play. 5. MENU control Press to bring up the disc menu. 6. AUX control Press to switch DVD player from play mode to auxiliary mode. 7. Auxiliary jacks Input ...

Remote control 1. REV (REVERSE) control Press to reverse the direction of the DVD movie. 2. FWD (FORWARD) control Press to advance the direction of the DVD movie. 3. PLAY/STOP control When playing, press PLAY/STOP to stop the disc. When stopped, pressPLAY/STOP to play the disc. 4. SEEK control Press...

Playback and format • The DVD player of your Family Entertainment DVD System can onlybe used in the “playback” mode. (The DVD player does not offer arecord feature.) • The system plays standard CDs or DVDs, CDR/RW, DVDRs, VCDs andMP3 media. Family Entertainment DVD System protection circuits High te...

On-screen indicators Each time a control is pressed, the operational status of the DVD playeris shown on the screen. The following are some possible indicators: 1. DVD/ CD STATUS (PLAY/FWD/REV/PAUSE) 2. CD track number / DVD title 3. DVD chapter number 4. MEDIA COUNTER — displays current viewing tim...

The front glass on the flip-down liquid crystal display (LCD) maybreak when hit with a hard surface. If the glass breaks, do not touch the liquid crystalline material. In case of contact with skin, washimmediately with soap and water. Do not expose the flip-down liquid crystal display (LCD) to direc...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Temperature selection: Controls the temperature of theairflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in thevehicle. See the following for a briefdescription on each control setting: MAX A/C: Distributes...

Operating tips • To reduce fog build up on the windshield during humid weather, placethe air flow selector in the position. • To reduce humidity build up inside the vehicle: do not drive with theairflow selector in the O (OFF) or with recirculated air engaged. • Do not put objects under the front se...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL(IF EQUIPPED) 1. Defrost: Distributes outside air through the windshield defroster and demister vents. Can be used to clear thin ice or fog from thewirndshield. To exit select another mode. 2. Passenger temperature control: Press to increase/decrease the airflo...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITHHEATED SEATS (IF EQUIPPED) 1. Defrost: Distributes outside air through the windshield defroster and demister vents. Can be used to clear thin ice or fog from thewirndshield. To exit select another mode. 2. Passenger temperature control: Press to increase/d...

DUAL ZONE AUTOMATIC TEMPERATURE CONTROL WITH REARPASSENGER COMPARTMENT CLIMATE CONTROL (IF EQUIPPED) 1. Defrost: Distributes outside air through the windshield defroster and demister vents. Can be used to clear thin ice or fog from thewirndshield. To exit select another mode. 2. Rear temperature con...

To aid in side window defogging/demisting in cold weather: 1. Select . 2. Select A/C. 3. Adjust the temperature control to maintain comfort. 4. Set the fan to the highest speed. 5. Direct the outer instrument panel vents towards the side windows. Do not place objects on top of the instrument panel a...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the headlamps on. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the hea...

Vertical aim adjustment 1. Park the vehicle directly in front of a wall or screen on a level surface,approximately 25 feet (7.6 meters) away. • (1) 8 feet (2.4 meters) • (2) Center height of lamp toground • (3) 25 feet (7.6 meters) • (4) Horizontal reference line 2. Measure the height of theheadlamp...

Replacing headlamp (high/low beam) bulbs 1. Make sure headlamp switch is in the OFF position, then open thehood. 2. Reach behind the headlamp assembly to access the bulb sockets andconnectors. 3. Locate the outboardmostelectrical connector and remove itby releasing the locking tab andpulling it off....

Replacing front sidemarker bulbs 1. Make sure headlamp switch is in the OFF position, then open thehood. 2. Reach behind the headlamp assembly to access the bulb sockets andconnectors. 3. Locate the front sidemarker lampelectrical connector and remove itby pulling it off. 4. Remove the bulb socket b...

MULTI-FUNCTION LEVER Windshield wiper: For intermittent operation, move control up oneposition. Adjust the rotary control to thedesired speed setting. Mist function: To activate mist, push control down from the OFFposition and release to get one wipe. For normal or low speed wiperoperation, move con...

Rear window wiper/washer controls For rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select: 2 — One second interval rear wiper. 1 — Ten second interval rear wiper. O — Rear wiper and washer off. For rear wash cycle, rotate (and hold as desired) the rear ...

TILT STEERING WHEEL To adjust the steering wheel: 1. Pull down and hold the steeringwheel release control. 2. Move the steering wheel up ordown until you find the desiredlocation. 3. Pull the steering wheel releasecontrol up. This will lock thesteering wheel in position. Never adjust the steering wh...

Conversation mirror (if equipped) The conversation mirror allows the driver to view the rear seating area. This does not replace the rear view mirror. Pull down on the housing to lock itin place. Adjust the mirror, asneeded, in any direction. The rear view mirror may have tobe adjusted to its lower ...

POWER WINDOWS Do not leave children unattended in the vehicle and do not letchildren play with the power windows. They may seriously injure themselves. When closing the power windows, you should verify they are freeof obstructions and ensure that children and/or pets are not in the proximity of the ...

If the switch is pressed and held to the normal open or ONE TOUCHDOWN position during a ONE TOUCH UP event, the window will stop. If,after 1/2 second the switch is still held, the window will perform anormal open or ONE TOUCH DOWN. Window lock The window lock feature allows onlythe driver to operate...

MIRRORS Power side view mirrors To adjust your mirrors: 1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror. 2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the center position tolock mirrors in place...

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is in the P (Park) position. Press and hold the rocker control(located on the instrument panel) toadjust accelerator and brake pedal. • Press the top of...

Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal or pressCNCL (Cancel). This will noterase your vehicle’s previously setspeed. • Press the speed control OFFcontrol. Note: When you turn off the speed control or the ignition, your speedcontrol set s...

In any mode: • Press VOL up or down to adjustthe volume. • Press MUTE to mute the volume. MOON ROOF (IF EQUIPPED) You can move the glass panel of the moon roof back to open or tilt up toventilate the vehicle. To open the moon roof: The moon roof is equipped with anautomatic, one-touch, expressopenin...

HOMELINK 姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink 威 Wireless Control System, located on the driver’s visor, provides a convenient way to replace up to three hand-held transmitterswith a single built-in device. This feature will learn the radio frequencycodes of most transmitters to opera...

7. Press and release the “learn” or “smart” button. (The name and colorof the button may vary by manufacturer.) Note: There are 30 seconds in which to initiate Step 8. 8. Return to the vehicle and firmly press, hold for two seconds andrelease the HomeLink 威 button. Repeat the press/hold/release sequ...

Operating the HomeLink 姞 Wireless Control System To operate, simply press and releasethe appropriate HomeLink 威 button. Activation will now occur for thetrained product (garage door, gateoperator, security system, entrydoor lock, or home or office lightingetc.). For convenience, thehand-held transmi...

MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle information through a constant monitor ofvehicle systems. You may select display features on the message center for a display of status. Thesystem will a...

Warnings Status Low brake fluid Warning returns after the ignition keyis turned from OFF to RUN Liftgate ajar (if equipped) Trunk ajar (if equipped) Check Traction Control (ifequipped) Washer Fluid level low Coolant level low Check engine Change oil soon Oil change required Data error DRIVER’S DOOR ...

CENTER CONSOLE Your vehicle may be equipped with a variety of console features. Theseinclude: • Utility compartment with powerpoint • Gear Shift • Cup holders • Rear vent and cup holders (ifequipped) Use only soft cups in the cupholder. Hard objects can injure youin a collision. Second row center co...

Mobile Communication Equipment includes, but is not limited to cellularphones, pagers, portable email devices, in-vehicle communicationssystems, telematics devices and portable two-way radios. A driver’s first responsibility is the safe operation of the vehicle.The most important thing you can do to...

KEYS One key operates all the locks and starts the vehicle. Always carry aspare key with you in case of an emergency. Your keys are programmed to your vehicle; using a non-programmed keywill not permit your vehicle to start. If you lose your dealer suppliedkeys, replacement keys are available throug...

Before starting, ensure the ignition is in the 1 (LOCK) position and allvehicle doors are closed. You must complete Steps 1–5 within 30 secondsor the procedure will have to be repeated. 1. Place the key in the ignition and turn the ignition to the 3 (RUN)position. 2. Press the power door unlock cont...

The remote entry system activates the illuminated entry feature; thisfeature turns on the lamps for 25 seconds or until the ignition is turnedto the 3 (RUN) position. The inside lights will not turn off if: • they have been turned on using the dimmer control or • any door is open. The battery saver ...

Activating the memory seat feature To activate this feature: 1. Position the seat, mirrors and adjustable pedals to the positiondesired. 2. Press the SET control on thedriver’s door panel. 3. Within 5 five seconds, press the 1or 2 control on the driver’s doorpanel to which you would like toassociate...

3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery. Refer to the diagram inside the remote entrytransmitter for the correct orientation of the battery. Press the batterydown to ensure that the battery is fully seated ...

6. The doors will lock, then unlock, to confirm that each remote entrytransmitter has been programmed. 7. Repeat Step 5 to program each additional remote entry transmitter. Note: The first remote transmitter programmed corresponds to Driver 1; the second, Driver 2. 8. Turn the ignition to the 1 (LOC...

The lights will turn off if all the doors and the liftgate remain closed and • 25 seconds elapse, or • the key is inserted in the ignition. KEYLESS ENTRY SYSTEM You can use the keyless entrykeypad to: • lock or unlock the doors withoutusing a key. • activate or deactivate theautolock feature. The ke...

3. Enter factory-set 5–digit entry code. 4. Press and hold the 7 • 8. While holding the 7 • 8 press the 3 • 4. 5. Release the 3 • 4. 6. Release the 7 • 8. The user should receive a horn chirp to indicate the system has been disabled or a chirp followed by a honk to indicate the system has beenenable...

If a problem occurs with the SecuriLock 娂 system, the indicator will flash rapidly or glow steadily when the ignition is in the 3 (RUN) position. Ifthis occurs, the vehicle will not start and should be taken to anauthorized dealer for service. Automatic arming The vehicle is armed immediately after ...

PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will help prevent your vehicle fromunauthorized entry. If there is any potential perimeter anti-theft problem with your vehicle,ensure ALL remote entry transmitters are brought to the dealership, to aid in troubleshooting. Arming t...

• Press the 7 • 8 and 9 • 0 controls on the keyless entry padat the same time to lock thedoors (driver’s door must beclosed). There is a 20 second countdownwhen any of the above actions occurbefore the vehicle becomes armed. Each door, the hood or the liftgateis armed individually, and if any areope...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Adjustable head restraints Head ...

Adjusting the front manual seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle ismoving. Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. Lift handle to move seat forward orbackward. Pull lever up to adjust seatback. Using the ...

Folding down the front passenger seatback (if equipped) The front passenger seatback can befolded to a horizontal position tomake room for a long load. To foldthe seatback: 1. Move the seat as far back aspossible. 2. Push the head restraint releasebutton and move the head restraintfully down. 3. Pul...

A position can be recalled: • in any gearshift position if the ignition is not in the RUN position. • only in Park or Neutral if the ignition is in the RUN position. A memory seat position may be programmed at any time. The memory positions are also recalled when you press your remoteentry transmitt...

Lift the handle located on the sideof the seat. The seatback will fold flat. Lift the handle all the way up untilthe seat releases from the floor.Rotate the seat forward to allowaccess to the third row. To return the seatback to the floorfrom tumbled position, rotate theseat down until you hear it l...

To return the seatback to the floorfrom tumbled position, rotate theseat down until you hear it latchingto the floor. To return the seatback to theupright position • Lift the seatback toward the rearof the vehicle, and • Rotate the seatback until youhear a click, locking it in theupright position. N...

Always latch the vehicle seat to the floor, whether the seat isoccupied or empty. If not latched, the seat may cause injury during a sudden stop. Stowing the third row bench or split bench seat (if equipped) 1. Push the head restraint releasebuttons and move the headrestraints fully down. Remove all...

2. To return the seatback to uprightposition, pull the number 1 strap,then while holding the number 1strap, pull the long strap located onthe seatback to raise the seatback. Ensure seat is latched to vehicle floor by pushing/pulling on seat.If not latched, the seat may cause injury during a sudden s...

SAFETY RESTRAINTS Personal Safety System 姟 The Personal Safety System 娂 provides an improved overall level of frontal crash protection to front seat occupants and is designed to helpfurther reduce the risk of airbag-related injuries. The system is able toanalyze different occupant conditions and cra...

(child size) occupants from airbag deployments when they areimproperly seated or restrained in the front passenger seat contrary toproper child-seating or restraint usage recommendations. Even with thistechnology, parents are STRONGLY encouraged to always properly restrain children in the rear seat....

the RCM also monitors the restraints warning light in the instrumentcluster. A difficulty with the system is indicated by one or more of thefollowing. • The warning light will either flash or stay lit. • The warning light will not illuminate immediately after ignition isturned on. • A series of five...

Each seating position in your vehicle has a specific safety beltassembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on theoutside shoulder only. Never wear the shoulder belt under the arm. 2)Never swing the safety belt around your n...

Energy Management Feature — Outboard • This vehicle has a safety belt system with an energy managementfeature at the front seats to help further reduce the risk of injury inthe event of a head-on collision. • This safety belt system has a retractor assembly that is designed toextend the seat belt we...

BeltMinder 姟 Note: If your vehicle is built without the passenger occupant classification sensor, the passenger BeltMinder 娂 feature is not available. The BeltMinder 娂 feature is a supplemental warning to the safety belt warning function. This feature provides additional reminders byintermittently s...

If... Then... The driver’s or frontpassenger’s safety belt becomesunbuckled for approximately 1minute while the vehicle istraveling at least 3 mph (5km/h) and more than 1-2minutes have elapsed since theignition switch has been turnedto ON... The BeltMinder 娂 feature is activated - the safety belt wa...

Reasons given... Consider... “Traffic is light” Nearly 1 of 2 deaths occur insingle-vehicle crashes, many when no other vehicles are around. “Belts wrinkle my clothes” Possibly, but a serious crash can domuch more than wrinkle your clothes,particularly if you are unbelted. “The people I’m with don’t...

Safety belt extension assembly If the safety belt is too short when fully extended, there is a 8 inch(20 cm) safety belt extension assembly that can be added (part number611C22). This assembly can be obtained from your dealer at no cost. Use only extensions manufactured by the same supplier as the s...

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) The instrument panel grab handle should never be used forstorage. The path of an inflating airbag must be kept clear at all times. The airbag supplemental restraint system (SRS) is designed to work inconjunction with the safety belts to help protect the dri...

Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries.Airbags DO NOT inflate slowly;there is a risk of injury from adeploying airbag. Do not place any object between an occupant and an airbag orne...

To properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching thepedals comfortably. • Recline the seat slightly one or two degrees from the upright position. Do not put anything on or over the air bag module. Placingobjects on or over the ai...

Determining if the system is operational The supplemental restraint system uses a warning indicator in theinstrument cluster or a back-up tone to indicate the condition of thesystem. Refer to the Warning lights and chimes section in the Instrument Cluster chapter. Routine maintenance of the airbag i...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

• diagnostic module. • and the electrical wiring which connects the components. The diagnostic module monitors its own internal circuits and thesupplemental airbag electrical system wiring (including the impactsensors), the system wiring, the airbag system readiness light, the airbagback up power an...

Side airbags, in combination with seat belts, can help reduce the risk ofsevere injuries in the event of a significant side impact collision. The side airbags are fitted on the outboard side of the seatbacks of thefront seats. In certain lateral collisions, the airbag on the side affected bythe coll...

Safety Canopy 姟 system (if equipped) Do not place objects ormount equipment on or near the headliner at the siderailthat may come into contact with adeploying Safety Canopy 娂 . Failure to follow these instructions mayincrease the risk of personal injuryin the event of a collision. Do not lean your h...

How does the Safety Canopy 姟 system work? The design and development of theSafety Canopy 娂 system included recommended testing proceduresthat were developed by a group ofautomotive safety experts known asthe Side Airbag Technical WorkingGroup. These recommended testingprocedures help reduce the risk...

The Safety Canopy 娂 is mounted to roof side-rail sheet metal, behind the headliner, along the entire side of the vehicle. In certain lateral collisionsor rollover events, the Safety Canopy 娂 system will be activated, regardless of which seats are occupied. The Safety Canopy 娂 is designed to inflate ...

• The readiness light will not illuminate immediately after ignition isturned on. • A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and light are repaired. If any of these things happen, even intermittently, have the SRS servicedat your dealership or ...

Follow all the important safety restraint and airbag precautions thatapply to adult passengers in your vehicle. If the shoulder belt portion of a combination lap and shoulder belt can bepositioned so it does not cross or rest in front of the child’s face or neck,the child should wear the lap and sho...

• Can the child stay seated like this for the whole trip? Types of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has aremovable shield, remove theshield and use the lap/shoulderbelt. If a seating position has alow seat b...

Follow all instructions provided by the manufacturer of thebooster seat. Never put the shoulder belt under a child’s arm or behind theback because it eliminates the protection for the upper part of the body and may increase the risk of injury or death in a collision. Never use pillows, books, or tow...

8. Allow the safety belt to retract toremove any slack in the belt. 9. Before placing the child in theseat, forcibly move the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the seat at the belt pathand attempt to move it side to sideand forward. There should ...

5. Rotate the tether strap clip. 6. Install the child safety seat tightlyusing the LATCH anchors or safetybelts. Follow the instructions in thischapter. 7. Tighten the child safety seattether strap according to themanufacturer’s instructions. Rear seating positions Follow Steps 1–7 as described abov...

• 2nd row bench (60/40) • 3rd row bench Note : The cargo tie-downs at the rear edge of the floor are nottether anchors. For additional important safety information on the proper use of safetybelts, child seats and infant seats, please read the entire Seating and safety restraints chapter in this own...

Your vehicle has LATCH anchors for child seat installation at the seatingpositions marked with the child seat symbol. Never attach two LATCHchild safety seats to the same anchor. In a crash, oneanchor may not be strong enoughto hold two child safety seatattachments and may break,causing serious inju...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperatu...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing thetire’s resistance to the gene...

Inspecting your tires Periodically inspect the tire treads for uneven or excessive wear andremove stones, nails, glass or other objects that may be wedged in thetread grooves. Check for holes or cuts that may permit air leakage fromthe tire and make necessary repairs. Also inspect the tire sidewalls...

Removing the spare tire and jack If the 3rd row seat (if equipped) is stowed in the floor, you will need tounstow it to access the spare tire and jack. Refer to Unstowing the 3rd row seat in the Seating and Safety Restraint chapter for this procedure. 1. Remove the carpeted floor panellocated in the...

Stowing the tire and jack 1. Fully collapse the jack, fold thelug wrench socket into the handleand place the jack and wrench intothe felt bag as shown. Take care toposition the jack as shown to ensurethat the locating holes in the jackbase can be placed on the locatingtabs of the jack mounting brack...

If you are stowing the flat tire, remove the “L”-shaped bolt from thelarge wing nut used to secure thespare tire in the vehicle. With the3rd row seat in the raised position,stand the flat tire in the rear of thevehicle with the tire’s valve stemfacing the rear of the vehicle.Fasten the flat tire to ...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

Safety practices Driving habits have a great deal to do with your tire mileage and safety. • Observe posted speed limits • Avoid fast starts, stops and turns • Avoid potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow,...

Wheel misalignment in the front or the rear can cause uneven and rapidtreadwear of your tires and should be corrected by a qualified technicianat a Ford or Lincoln Mercury dealer. Front wheel drive (FWD) vehiclesand those with an independent rear suspension (if equipped) mayrequire alignment of all ...

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask a qualified technician at a Ford or Lincoln Mercury dealership to check ...

tires and chains. If you need to use snow tires and chains, it isrecommended that steel wheels are used of the same size andspecifications as those originally installed. Follow these guidelines when using snow tires and chains: • Use only SAE class “S” cables or equivalent on the front axle forP215/...

Vehicle Curb Weight – is the weight of your new vehicle when you picked it up from your dealer plus any aftermarket equipment. Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or ...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. 2005 Freestyle (219) Owners Guide (post-2002-fmt)USA (fus) Tires, Wheels and Loading 182

GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance...

The following gives you a few examples on how to calculate the availableamount of cargo and luggage load capacity: • Another example for your vehicle with 1400 lb. (635 kg) of cargo andluggage capacity. You decide to go golfing. Is there enough loadcapacity to carry you, 4 of your friends and all th...

Trailer lamps Trailer lamps are required on most towed vehicles. Make sure all runninglights, brake lights, turn signals and hazard lights are working. See yourdealer or trailer rental agency for proper instructions and equipment forhooking up trailer lamps. Driving while you tow When towing a trail...

RECREATIONAL TOWING Follow these guidelines for your specific powertrain combination to towyour vehicle for personal travel (such as behind a recreational vehicle ormoving truck). In case of roadside emergency with a disabled vehicle, please refer to the Wrecker towing section in the Driving chapter...

STARTING Positions of the ignition 1. LOCK, locks the automatictransaxle gearshift lever and allowskey removal. This position also shutsthe engine and all electricalaccessories off without locking thesteering wheel. To lock the steeringwheel, remove the key then turn thesteering wheel. 2. ACC, allow...

Starting the engine 1. Turn the key to 3 (ON) withoutturning the key to 4 (START). 2. Turn the key to 4 (START), thenrelease the key as soon as theengine starts. Excessive crankingcould damage the starter. Note: If the engine does not start within five seconds on the first try, turn the key to OFF, ...

BRAKES Occasional brake noise is normal. If a metal-to-metal, continuous grindingor continuous squeal sound is present, the brake linings may be worn-outand should be inspected by a qualified service technician. If the vehiclehas continuous vibration or shudder in the steering wheel while braking,th...

Parking brake Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops. The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released....

detecting and controlling wheel spin. The system borrows many of theelectronic elements already present in the anti-lock braking system(ABS). Wheel-speed sensors allow excess wheel spin to be detected by theTraction Control 娂 portion of the ABS computer. Excess wheel spin is controlled through engin...

R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward.Always come to a complete stop before shifting into and out of R(Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this p...

Certain add-on devices such as large trailer hitches, bike orsurfboard racks and any device that may block the normal detection zone of the RSS system may create false beeps. The RSS detects obstacles up to sixfeet (two meters) from the rearbumper with a decreased coveragearea at the outer corners o...

If your vehicle sustains damage to the rear bumper/fascia, leavingit misaligned or bent, the sensing zone may be altered causinginaccurate measurement of obstacles or false alarms. ALL WHEEL DRIVE (AWD) SYSTEM (IF EQUIPPED) Your vehicle may be equipped with a full-time All Wheel Drive (AWD)system. W...

Mud and water If you must drive through high water, drive slowly. Traction or brakecapability may be limited. When driving through water, determine the depth; avoid water higherthan the bottom of the hubs (if possible) and proceed slowly. If theignition system gets wet, the vehicle may stall. Once t...

Make sure you allow sufficient distance between you and other vehiclesfor stopping. Drive slower than usual and consider using one of the lowergears. In emergency stopping situations, apply the brake steadily. Sinceyour vehicle is equipped with a four wheel anti-lock brake system (ABS),do not “pump”...

GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the New Vehicle Limited...

Canadian customers who require roadside assistance, call1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford MotorCompany will reimburse a reasonable amount. To obtain reimbursementinformation, U.S. Ford or Mercury vehicles customers call1-800-241-3673; Lincoln vehicle custo...

The fuel pump shut-off switch islocated in the front passengerfootwell area in the right uppercorner. To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset theswitch by pushing in on the resetbutton. 4. Turn the ignition ON. 5. Wait a f...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow Blue Blue 25A Natural Natural — — — 30A Green Green Green Pin...

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description F1 20A High beams F2 15A Interior lamps (Courtesy and demandlamps), Delayed accessory (Powerwindows and moonroof) F3 25A Access/Security (Power door lockactuators, Liftgate lock actuator,...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description F19 10A Anti-lock Brake System (ABS)/Tractioncontrol module, All Wheel Drive (AWD)module, RSS, Heated seat modules F20 7.5A Cluster, Climate control F21 7.5A Restraint Control Module (RCM) F22 7.5A Auxiliary climate con...

The high-current fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 80A* Interior fuse panel (SJB), SJB fuses 1,2, 3, 4, 5, 8 and 12 2 — Not used 3 — Not used 4 50A* Wiper RUN/ACC relay to PDB, PDBfuses 37 and 38 5 — Not used 6 20A* Moonroof 7 — Not ...

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 43 — Not used 44 — Not used 45 — Not used 46 — Not used 47 — Not used 48 1 ⁄ 2 ISO relay Fog lamps 49 — Not used 50 1 ⁄ 2 ISO relay Auxiliary coolant pump 51 1 ⁄ 2 ISO relay A/C clutch 52 — Not used 53 1 ⁄ 2 ISO relay Fuel pump d...

Preparing your vehicle When the battery is disconnected or a new battery is installed, thetransmission must relearn its shift strategy. As a result, the transmissionmay have firm and/or soft shifts. This operation is considered normal andwill not affect function or durability of the transmission. Ov...

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second ...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Remove the jumper cable on the negative (...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handling your vehicle linewill provide warranty service, we recommend you return to your sellingdealer who wants to ensure your continued satisfaction. Pl...

THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes. • available free to owners and lessees of qualifying Ford Motor Companyvehicles. The Dispute Settlement Board may not be available in all states. FordMot...

Board membership The Board consists of: • Three consumer representatives • A Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained byan independent consulting firm. The dealership Board member is chosenfrom Ford and Lincoln Mercury deale...

Oral presentations If you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral presentationbefore the Board, this is not a requirement and the Board will decide thecase whether or not an oral presentation is made. An oral prese...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealerships. In those caseswhere you continue to feel that the efforts by Ford of Canada and thedealer to resolve a factory-related vehicle service concern have beenunsatisfactory, Ford of Canada p...

If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformation is subject to change, please ask your dealer for completedetails about Ford Extended Service Plan coverage options, or visit theFord ESP website at ...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which isavailable from your dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can discolor and s...

• Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and industrial fallout before repairing paint chips. • Always read the instructions before using the products. ALUMINUM WHEELS AND WHEEL COVERS Aluminum wheels and wheel covers are coated with a clearcoat paint...

• 3.0L Duratec engine • Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your dealer. • For routine cleaning, use Motorcra...

Do not use sharp objects, such as a razor blade, to clean theinside of the rear window or to remove decals, as it may causedamage to the rear window defroster’s heated grid lines. INSTRUMENT PANEL AND CLUSTER LENS Clean the instrument panel with a damp cloth, then with a clean, drycloth, or use Moto...

Do not use cleaning solvents, bleach or dye on the vehicle’ssafety belts, as these actions may weaken the belt webbing. Do not use chemical solvents or strong detergents when cleaningthe seat-mounted side air bag. Such products could contaminate the side air bag system and affect performance of the ...

Motorcraft Car Wash (Canada only) (CXC-21) Motorcraft Custom Bright Metal Cleaner (ZC-15) Motorcraft Custom Clear Coat Polish (ZC–8–A) Motorcraft Custom Vinyl Protectant (U.S. only) (ZC-40-A) Motorcraft Dash and Vinyl Cleaner (ZC-38–A) Motorcraft Deluxe Leather and Vinyl Cleaner (U.S. only) (ZC-11–A...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provi...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel nearthe steering column. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood. 3. Lift the hood and support it withthe prop...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16–A2.Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic c...

5. Locate and carefully remove theengine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added...

• If required, add engine oil to theengine. Refer to Adding engine oil in this chapter. • Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the engine is overfilled, some oil must beremoved from the engine by aqualified service technician. 7. Put the indicator ...

Engine oil and filter recommendations Look for this certificationtrademark. Use SAE 5W-20 engine oil. Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol conformsto the current engine and emission system protection standards and ...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. However, for severe usage or in high temperature climates, check thebattery electrolyte level. Refer to scheduled maintenance information for the servi...

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.Lift the battery with a battery carrier or with your hands on oppositecorners. Keep batteries out of reach of ...

If the battery has been disconnected or a new battery has been installed,the clock and radio settings must be reset once the battery isreconnected. • Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling ...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interv...

Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine...

1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the coolant reservoir (an opaque plastic bottle).Slowly turn cap counterclockwise (left) until pressure begins to release. 3. Step back while the pressure...

If you have to add more than 1.0 quart (1.0 liter) of engine coolant permonth, have your dealer check the engine cooling system. Your coolingsystem may have a leak. Operating an engine with a low level of coolantcan result in engine overheating and possible engine damage. Recycled engine coolant For...

• Decreased engine coolant concentrations below 40% willdecrease the freeze protection characteristics of the enginecoolant and may cause engine damage. • Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperature...

Refueling Fuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep spa...

Do not be concerned if your engine sometimes knocks lightly. However, ifit knocks heavily under most driving conditions while you are using fuelwith the recommended octane rating, see your dealer or a qualifiedservice technician to prevent any engine damage. Fuel quality If you are experiencing star...

• Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in miles or kilometers). 2. Each time you fill the tank, record ...

Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test ofthe on-board diagnostics system. If your indicator is on, refer to the description in the Warning lights and chimes section of the Instrument Cluster chapter. Your vehicle may n...

BRAKE FLUID The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“MAX” lines are within the normaloperating range; there is no need toadd fluid. If the fluid levels areoutside of the normal operatingrange the perfor...

LUBRICANT SPECIFICATIONS Items Ford PartName orequivalent Ford PartNumber FordSpecification Brake fluid Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeFluid PM-1 ESA-M6C25-AorWSS-M6C62–A Door latch, hoodlatch, auxiliaryhood latch, seattracks, trunkand liftgatelatches Multi-PurposeGrease XG-4 or X...

Items Ford PartName orequivalent Ford PartNumber FordSpecification Power TransferUnit Motorcraft SAE75W-90 FuelEfficient HighPerformanceRear AxleLubricant XY-75W-90–QFEHP — Engine oil Motorcraft SAE5W-20 PremiumSynthetic BlendMotor Oil (US)Motorcraft SAE5W-20 SuperPremium MotorOil (Canada) XO-5W20-Q...

The Vehicle Identification Number (VIN) contains the following information: 1. World manufacturer identifier 2. Brake type and Gross VehicleWeight Rating (GVWR) 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number Engine numbe...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford or Ford of Canada dealer.These quality accessories have been specifically engineered to fulfill yourautomotive needs; they are custom designed to co...

A Accessory delay ..........................66 Air cleaner filter .......................266 Air conditioning ........42, 44, 46, 48 Airbag supplemental restraintsystem ................132–133, 139, 142 and child safety seats ............134description ..............133, 139, 142disposal ..............