Ford 2005 Focus v.4- Manuals

SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury to yourself or others? Inthis guide, answers to such questions are contained in commentshighlighted by the warning triangle symbol. These comments should beread and observed. Warning symbol...

SPECIAL NOTICES New Vehicle Limited Warranty For a detailed description of what is covered and what is not covered byyour vehicle’s New Vehicle Limited Warranty, refer to the Warranty Guide that is provided to you along with your Owner’s Guide. Special instructions For your added safety, your vehicl...

Event Data Recording Other modules in your vehicle — event data recorders — are capable ofcollecting and storing data during a crash or near crash event. Therecorded information may assist in the investigation of such an event.The modules may record information about both the vehicle and theoccupant...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -No...

WARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lig...

converter. Drive in a moderate fashion (avoid heavy acceleration anddeceleration) and have your vehicle serviced immediately by yourauthorized dealer. Under engine misfire conditions, excessive exhaust temperaturescould damage the catalytic converter, the fuel system, interior floor coverings or oth...

Airbag readiness: If this light fails to illuminate when ignition is turnedto ON, continues to flash or remainson, have the system servicedimmediately by your authorized dealer. A chime will also sound when amalfunction in the supplemental restraint system has been detected. Safety belt: Reminds you...

Traction Control 娂 system (if equipped): Illuminates when the Traction Control 娂 is turned OFF and will flash when active. If thelight remains on, have the systemserviced immediately, refer to the Driving chapter for more information. Low fuel: Illuminates when the fuel level in the fuel tank is at ...

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range. If it enters the red section, the engine isoverheating. Stop the vehicle assoon as safely possible, s...

AM/FM STEREO WITH SINGLE CD — PREMIUM (IF EQUIPPED) AM/FM STEREO WITH SINGLE CD/MP3 — PREMIUM(IF EQUIPPED) 2005 Focus (foc)Owners Guide (post-2002-fmt)USA (fus) Entertainment Systems 16

1. / Tune selector: Press to manually increase/decrease theradio frequency. 2. Phone/mute: Press to mute the playing media. Press again to returnto the playing media. 3. Menu: Press MENU to access the main menu functions. Use the Tune selector ( / ) or SEEK for adjustments. Track/Folder mode: (Avail...

REMOTE AUDIO STEERING COLUMN CONTROLS (IF EQUIPPED) The remote audio steering column controls may be used to select radioor CD mode. The following functions can be carried out using the remotecontrol. • Volume: Pull VOL+ towards the steering wheel to increase the volume.Pull VOL- towards the steerin...

AM: 530, 540–1700, 1710 kHz FM: 87.7, 87.9–107.7, 107.9 MHz RADIO RECEPTION FACTORS There are three factors that can affect radio reception: • Distance/strength: The further you travel from an FM station, theweaker the signal and the weaker the reception. • Terrain: Hills, mountains, tall buildings,...

HEATER ONLY SYSTEM(IF EQUIPPED) 1. Air flow selections: Controls the direction of the airflow in thecabin. See the following for a briefdescription on each control. : Distributes air through the instrument panel vents. : Distributes air through the instrument panel vents and the floorvents. : Distri...

2. Adjust the temperature control to maintain comfort. 3. Set the fan speed to the highest setting. 4. Direct the outer instrument panel vents toward the side windows. To increase airflow to the outer instrument panel vents, close the ventslocated in the middle of the instrument panel. Do not place ...

5. A/C: Provides cabin cooling. 6. Temperature selection: Controls the temperature of the airflow in the cabin. Max A/C: For maximum cabin cooling performance, select A/C (5) and (4). Operating tips • To reduce fog build up on the windshield during humid weather, placethe air flow selector in the po...

REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice andfog. • A small LED will illuminate whenthe rear defroster is activated. The ignition must be in the ONposition to operate the rear window defr...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps,license plate lamps and tail lamps. Turns the headlamps on. Foglamp control (if equipped) The headlamp control also operatesthe foglamps. The foglamps can beturned on when the headlampcontrol is in the position ...

3. Turn on the low beam headlamps to illuminate the wall or screen andopen the hood. 4. On the wall or screen you willobserve an area of high intensitylight. The top of the high intensityarea should touch the horizontalreference line. If not, the beam willneed to be adjusted. 5. Locate the vertical ...

INTERIOR LAMPS Dome lamps The dome lamp is equipped with acontrol switch that will illuminatewhen: • the doors are closed and theswitch is in the on position. • the switch is in the door activatedposition and any door is open. When the dome lamp switch is in the off position, it will not illuminatew...

Replacing side marker bulbs 1. Make sure the headlamp controlis in the OFF position. 2. Reach under the front fender,grasp the bulb socket and turn itcounterclockwise to remove it. 3. Pull the bulb straight out. Install in reverse order. Replacing high-mount brake lamp bulbs Sedan 1. Make sure the h...

MULTI-FUNCTION LEVER Windshield wiper: Move the lever down for a single wipe. For intermittent operation, movecontrol up one position and adjustthe rotary control to the desiredspeed. For normal operation, move controlup two positions. For high speed operation, move control up three positions. Mist ...

Changing the wiper blades 1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to release the bladeand pull the wiper blade downtoward the windshield to remove itfrom the arm. 2. Attach the new wiper to thewiper arm and press it into pla...

Cigar lighter (if equipped) Do not plug optional electrical accessories into the cigarette lightersocket. Do not hold the lighter in with your hand while it is heating, this willdamage the lighter element and socket. The lighter will be released fromits heating position when it is ready to be used. ...

MIRRORS Power side view mirrors (if equipped) To adjust your mirrors: 1. Rotate the control clockwise toadjust the right mirror and rotatethe control counterclockwise toadjust the left mirror. 2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the center position tolock mi...

Setting speed control The controls for using your speedcontrol are located on the steeringwheel for your convenience. 1. Press the ON control and releaseit. 2. Accelerate to the desired speed. 3. Press the SET ACCEL controland release it. 4. Take your foot off the acceleratorpedal. 5. The indicator ...

• Depress the brake pedal until thedesired vehicle speed is reached,press the SET ACCEL control. Turning off speed control Press the speed control OFFcontrol. Note: When you turn off the speed control or the ignition, your speedcontrol set speed memory is erased. MOON ROOF (SUNROOF) (IF EQUIPPED) Yo...

To vent: • To tilt the moon roof into the vent position (when the glass panel isclosed), press and hold the front portion of the control. • To close the moon roof from the vent position, press and hold the rearportion of the control until the glass panel stops moving. Before operating the moonroof y...

Wagon Pull out the roller cover and securethe retaining points. The cover canbe removed completely by pressinginward on both ends of the support. To reduce the risk of injury,the luggage cover must be properly attached to the mountingclips. Do not place any objects on the cargo area cover. They mayo...

Make sure that the liftgate door is closed to prevent exhaustfumes from being drawn into the vehicle. This will also prevent passengers and cargo from falling out. If you must drive with theliftgate door open, keep the vents open so outside air comes into thevehicle LUGGAGE RACK (IF EQUIPPED) The ma...

KEYS The key operates all locks on your vehicle. You should always carry asecond key with you in a safe place in case you require it in anemergency. Your keys are coded to your vehicle; using a non-coded key will notpermit your vehicle to start. If you lose your dealer supplied keys,replacement keys...

Childproof door locks (if equipped) • When these locks are set, therear doors cannot be opened fromthe inside. • The rear doors can be openedfrom the outside when the doorsare unlocked. The childproof locks are located onrear edge of each rear door andmust be set separately for eachdoor. Setting the...

REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RS-210 ofIndustry Canada. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) This devicemust accept any interference received, including interfe...

4. Insert the new battery. Refer to the diagram inside the remote entrytransmitter for the correct orientation of the battery. Press the batterydown to ensure that the battery is fully seated in the battery housingcavity. 5. Snap the two halves back together. Note: Replacement of the battery will no...

SECURILOCK 姟 PASSIVE ANTI-THEFT SYSTEM SecuriLock 娂 passive anti-theft system is an engine immobilization system. This system is designed to help prevent the engine from beingstarted unless a coded key programmed to your vehicle is used. The use of the wrong type of coded key may lead to a “no-start...

Replacing coded keys can be very costly. Store an extra programmed keyaway from the vehicle in a safe place to help prevent any inconveniences.Please visit an authorized dealer to purchase additional spare or replacement keys. Programming spare keys You can program your own coded keys to your vehicl...

10. Turn the ignition from the 2 (OFF) position to the 3 (ON) position.Keep the ignition in the 3 (ON) position for at least one second, but nomore than 10 seconds.11. Your new, unprogrammed key is now programmed.If the key has been successfully programmed it will start the vehicle’sengine and the t...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Before returning the seatback to...

Adjusting the front manual seat Pull the lever located under thefront edge of the seat to move theseat forward or backward. Turn the handle to adjust the heightof the seat. Lift the control to adjust the angleof the seatback. Reclining the seatback can cause an occupant to slide under theseat’s safe...

To operate the heated seats: • Push control to activate. • Push again to deactivate. The heating will operate when the ignition switch is in position 2. The indicator light on the switch is illuminated when activated. Althoughthe indicator light is illuminated, the heat is regulated by a thermostatw...

Do not place objects behind the seat which could prevent theengagement of the seat lock. REAR SEATS Folding rear seat cushion forward Lift the seat cushion and pull itforward. Before returning the seatback to its original position, make surethat cargo or any objects are not trapped behind the seatba...

Sedan Remove the head restraints (ifequipped) of the rear seats andstow them on the floor behind thefront seats. Pull one or both of the unlockingcontrols in the luggage compartmentand fold the rear seatback forward. Returning the seatback to the upright position Fold back the seatback until it lock...

Folding the seat cushion and seatback forward Fold the seat cushion forward. Remove the head restraint(s) (ifequipped) of the rear seat, and foldthe seatback forward. Stow the head restraint(s) in theplastic retainers provided in the nowupright underside of the seatcushion, as shown on the decal. Wh...

Front passenger sensing system For airbags to do their job they must inflate with great force, and thisforce can pose a potentially deadly risk to occupants that are very closeto the airbag when it begins to inflate. For some occupants, like infantsin rear-facing child seats, this occurs because the...

Front safety belt pretensioners The safety belt pretensioners are designed to tighten the safety beltsfirmly against the occupant’s body during a collision. This maximizes theeffectiveness of the safety belts and helps properly position the occupantrelative to the airbag to improve protection. The s...

To reduce the risk of injury, make sure children sit where theycan be properly restrained. Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child from injury in a collision. All occupants of the vehicle, including the driver, should al...

Automatic locking mode When to use the automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to remove any slack in the shoulder belt. The automaticlocking mode is not available on the driver safety belt. This mode should be used any time a ch...

How to disengage the automatic locking mode Ford Motor Company recommends that all passenger safety beltassemblies and attaching hardware should be inspected by an authorized dealer after any collision to verify that the ⬙ automatic locking retractor ⬙ feature for child seats is still working proper...

If... Then... The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the ONposition or less than 1-2minutes have elapsed since theignition switch has been turnedON... The BeltMinder 娂 feature will not activate. The driver’s or frontpassenger’s safety belt is...

Do not sit on top of a buckled safety belt to avoid theBeltMinder 娂 chime. Sitting on the safety belt will increase the risk of injury in an accident. To disable (one-time) or deactivate theBeltMinder 娂 feature please follow the directions stated below. One time disable If at any time the driver/fro...

• Step 3 must be completed within 50 seconds after the safety beltwarning light turns off. 3. For the seating position being disabled, at a moderate speed, bucklethen unbuckle the safety belt 9 times, ending in the unbuckled state.(Step 3 must be completed within 50 seconds after the safety beltwarn...

equipped), child safety seat LATCH and tether anchors, and attachinghardware, should be inspected after a collision. Ford Motor Companyrecommends that all safety belt assemblies in use in vehicles involved ina collision be replaced. However, if the collision was minor and anauthorized dealer finds t...

Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries.Airbags DO NOT inflate slowly;there is a risk of injury from adeploying airbag. All occupants of the vehicle, including the driver, should alw...

Do not attempt to service, repair, or modify the airbagsupplemental restraint systems or its fuses. See your authorized dealer. Children and airbags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions tha...

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion pr...

• diagnostic module. • and the electrical wiring which connects the components. The diagnostic module monitors its own internal circuits and thesupplemental airbag electrical system wiring (including the impactsensors), the system wiring, the airbag system readiness light, the airbagback up power an...

If it is necessary to modify an advanced front airbag system toaccommodate a person with disabilities, contact the Ford CustomerRelationship Center at the phone number shown in the Customer Assistance section of this Owner’s Guide . Any alteration/modification to the front passenger seat mayaffect t...

Do not lean your head on the door. The side airbag could injureyou as it deploys from the side of the seatback. Do not attempt to service, repair, or modify the airbag SRS, itsfuses or the seat cover on a seat containing an airbag. See your authorized dealer. All occupants of the vehicle should alwa...

panel and occupant to further enhance the protection providedoccupants in side impact collisions. The airbag SRS is designed to activate when the vehicle sustains lateraldeceleration sufficient to cause the sensors to close an electrical circuitthat initiates airbag inflation. The fact that the airb...

Always transport children 12 years old and under in the backseat and always use appropriate child restraints. Accident statistics indicate that children are safer when properlyrestrained in the rear seats. Do not leave children, unreliable adults, or pets unattended inyour vehicle. Safety belts and ...

neck, the child should wear the lap and shoulder belt. Moving the childcloser to the center of the vehicle may help provide a good shoulder beltfit. Do not leave children, unreliable adults, or pets unattended inyour vehicle. Child booster seats Children outgrow a typical convertible or toddler seat...

Types of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has aremovable shield, remove theshield and use the lap/shoulderbelt. If a seating position has alow seat back and no headrestraint, a backless booster seatmay place...

• LATCH lower anchors are recommended for use by children up to 48lb. (22 kg) in a child restraint. Top tether anchors can be used forchildren up to 60 lb. (27 kg) in a child restraint, and to provide uppertorso restraint for children up to 80 lb. (36 kg) using an upper torsoharness and a belt-posit...

8. Allow the safety belt to retract toremove any slack in the belt. 9. Before placing the child in theseat, forcibly move the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the seat at the belt pathand attempt to move it side to sideand forward. There should ...

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrades can be found whereapplicable on the tire sidewallbetween tread shoulder andmaximum section width. Forexample: • Treadwear 200 Traction AA Temperatu...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing thetire’s resistance to the gene...

tread grooves. Check for holes or cuts that may permit air leakage fromthe tire and make necessary repairs. Also inspect the tire sidewalls for cuts, bruises and other damage. Ifinternal damage to the tire is suspected, have the tire demounted andinspected in case it needs to be repaired or replaced...

is located on the B-Pillar or the edge of the driver’s door. The coldinflation pressure should never be set lower than the recommendedpressure on the Safety Compliance Certification Label. When weather temperature changes occur, tire inflation pressures alsochange. A 10° F (6° C) temperature drop ca...

Tire change procedure 1. Park on a level surface, activatehazard flashers and set the parkingbrake. When one of the front wheels is off the ground, the transaxlealone will not prevent the vehicle from moving or slipping off the jack, even if the vehicle is in P (Park) (automatic transaxle) or R(Reve...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

Note: You may not find this information on all tires because it is not required by federal law. Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R 106 mph (171 km/h) S 112 mph (180 km/h) T 118 mph (190 km/h) U 124 mph (200 km/h) H 130 mph (210 km/h)...

12. Treadwear, Traction and Temperature Grades • Treadwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on aspecified government test course. For example, a tire graded 150would wear one and one-half (1 1 ⁄ 2 ) times as well ...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

the road in adverse (wet, snowy, etc.) conditions. Visually check yourtires for uneven wear, looking for high and low areas or unusuallysmooth areas. Also check for signs of tire damage. When the tread is worn down to1/16th of an inch (2 mm), tires mustbe replaced to prevent your vehiclefrom skiddin...

If your vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. Never spin the tires in excess of the 35 mph (55 km/h) pointindicated on the speedometer. Highway h...

Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanicalproblem involved before tire rotation. Note: Your vehicle may be equipped with a dissimilar...

Exceeding any vehicle weight rating limitation could result inserious damage to the vehicle and/or personal injury. Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX kg or XXX lbs.” on your vehicle’s placard. 2. D...

transport the cement to your home? If you and your friend each weigh220 lb. (99 kg), the calculation would be: 1400 – (2 x 220) – (12 x100) = 1400 – 440 – 1200 = – 240 lb. No, you do not have enoughcargo capacity to carry that much weight. In metric units, thecalculation would be: 635 kg — (2 x 99 k...

Model Passengers/Luggage load - lb. (kg) Maximum trailer weight - lb. (kg) Wagon 5/827 (375) 500 (227) 4/677 (307) 650 (295) 3/527 (239) 800 (363) 2/377 (171) 950 (431) 1/227 (103) 1100 (499) This chart is based on the specified vehicle at a maximum GCW(Vehicle Weight + Trailer Weight) equal to 4,30...

Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes aresafe if installed properly and adjusted to the manufacturer’sspecifications. The trailer brakes must meet local and Federalregulations. Do not connect a trailer’s hydraulic brake system directly to yourvehicle’s bra...

• If you are driving down a long or steep hill, shift to a lower gear. Donot apply the brakes continuously, as they may overheat and becomeless effective. • The trailer tongue weight should be 10–15% of the loaded trailerweight. • After you have traveled 50 miles (80 km), thoroughly check yourhitch,...

STARTING Positions of the ignition 1. LOCK, locks the steering wheel,automatic transaxle gearshift leverand allows key removal. 2. OFF, shuts the engine and allelectrical accessories off withoutlocking the steering wheel. 3. ON, all electrical circuitsoperational. Warning lightsilluminated. Key posi...

Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate. Starting the engine 1. Turn the key to 3 (ON) withoutturning the key to 4 (START). 2. Turn the key t...

BRAKES Occasional brake noise is normal. If a metal-to-metal, continuous grindingor continuous squeal sound is present, the brake linings may be worn-outand should be inspected by an authorized dealer. If the vehicle hascontinuous vibration or shudder in the steering wheel while braking, thevehicle ...

Even when the ABS is disabled,normal braking is still effective. (Ifyour BRAKE warning lampilluminates with the parking brakereleased, have your brake system serviced immediately.) Parking brake To set the parking brake (1), pullthe parking brake handle up as faras possible. The BRAKE warning lamp w...

During Traction Control 娂 operation, the traction control active light willilluminate, you may hear an electricmotor type of sound coming fromthe engine compartment and theengine will not “rev-up” when you push further on the accelerator. Thisis normal system behavior and should be no reason for con...

If the steering wanders or pulls, check for: • an improperly inflated tire • uneven tire wear • loose or worn suspension components • loose or worn steering components • improper steering alignment A high crown in the road or high crosswinds may also make the steeringseem to wander/pull. AUTOMATIC T...

2 (Second) This position allows for second gear only. • Provides engine braking. • Use to start-up on slippery roads. • To return to D (Overdrive), move the gearshift lever into the D(Overdrive) position. • Selecting 2 (Second) at higher speeds will cause the transaxle todownshift to second gear at ...

To start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor, then put the gearshift lever in theneutral position. 3. Start the engine, then press the brake pedal and release the parkingbrake. 4. Move the gearshift lever to the desired gear, then slowly r...

Parking your vehicle 1. Apply the brake and shift into the neutral position. 2. Fully apply the parking brake, then shift into 1 (First). 3. Turn the ignition off. Do not park your vehicle in Neutral, it may move unexpectedlyand injure someone. Use 1 (First) gear and set the parking brake fully. Rem...

GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the New Vehicle Limited...

Canadian customers who require roadside assistance, call1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford MotorCompany will reimburse a reasonable amount. To obtain reimbursementinformation, U.S. Ford or Mercury vehicles customers call1-800-241-3673; Lincoln vehicle custo...

This switch is located in the frontpassenger’s footwell, behind the kickpanel access cover. To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset theswitch by pushing in on the resetbutton. 4. Turn the ignition ON. 5. Wait a few seconds...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 61 7.5A PATS modules, Instrument cluster 62 7.5A Radio (Start) 63 20A Power locks (GEM) Fuse 63 is located on the back of the fuse panel. See your authorizeddealer for service of this fuse. Power distribution box The po...

4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect any electricalsurges. Turn all other accessories off. Connecting the jumper cables 1. Connect the po...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part (engine lifting eye, see following graphic) of the stalledvehicle’s engine, away from the battery and the carburetor/fuel injectionsy...

• 2.0L/2.3L engines 5. Ensure that the cables are clear of fan blades, belts, moving parts ofboth engines, or any fuel delivery system parts. Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Remove the jumper cable on the negative (...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized dealer for warrantyrepairs. While any authorized dealer handling your vehicle line willprovide warranty service, we recommend you return to your sellingauthorized dealer who wants to ensure your continued satisfac...

THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes. • available free to owners and lessees of qualifying Ford Motor Companyvehicles. The Dispute Settlement Board may not be available in all states. FordMot...

Board membership The Board consists of: • Three consumer representatives • An authorized dealer representative Consumer candidates for Board membership are recruited and trained byan independent consulting firm. The dealership Board member is chosenfrom authorized dealer management, recognized for t...

Oral presentations If you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral presentationbefore the Board, this is not a requirement and the Board will decide thecase whether or not an oral presentation is made. An oral prese...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those caseswhere you continue to feel that the efforts by Ford of Canada and theauthorized dealer to resolve a factory-related vehicle service concernhave been unsatisfactory, Ford of C...

If you did not take advantage of the Ford Extended Service Plan at thetime of purchasing your vehicle, you may still be eligible. Since thisinformation is subject to change, please ask your authorized dealer forcomplete details about Ford Extended Service Plan coverage options, orvisit the Ford ESP ...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which isavailable from your authorized dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can dis...

• Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and industrial fallout before repairing paint chips. • Always read the instructions before using the products. ALUMINUM WHEELS AND WHEEL COVERS Aluminum wheels and wheel covers are coated with a clearcoat paint...

• 2.0L and 2.3L I4 Engines PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your authorized dealer. • For routine cleaning, use Motorcraft Detail Wash (ZC-3–A). • If tar or grease spots are present, use Motorcraft Bug and TarRem...

• Do not use abrasives, as they may cause scratches. • Do not use fuel, kerosene, or paint thinner to clean any parts. Do not use sharp objects, such as a razor blade, to clean theinside of the rear window or to remove decals, as it may causedamage to the rear window defroster’s heated grid lines. I...

Do not use chemical solvents or strong detergents when cleaningthe seat-mounted side airbag. Such products could contaminate the side airbag system and affect performance of the side airbag in acollision. LEATHER SEATS (IF EQUIPPED) Your leather seating surfaces have a clear, protective coating over...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your authorized dealer ca...

Working with the engine on • Automatic transmission: 1. Set the parking brake and shift to P (Park). 2. Block the wheels. • Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N(Neutral). 2. Block the wheels. Note: Do not start your engine with the air cleane...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.0L/2.3L I4 Engines 1. Power steering fluid reservoir 2. Engine oil filler cap 3. Brake/Clutch fluid reservoir 4. Power distribution box 5. Battery 6. Automatic transaxle fluid dipstick (if equipped) 7. Engine oil dipstick 8. Engine coolant reservoir...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16–A2.Do not use any special washer fluidsuch as windshield water repellenttype fluid or bug wash. They m...

5. Locate and carefully remove the engine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is between the MIN and MAX marks , the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MINmark, add enou...

Engine oil and filter recommendations Look for this certificationtrademark. Use SAE 5W-20 engine oil. Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). An oil with this trademark symbol conformsto the current engine and emission system protection standards and ...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trouble-free operation, keep...

Keep batteries out of reach of children. Batteries contain sulfuricacid. Avoid contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing ofacid solution. In case of acid contact with skin or eyes, flushimmediately with water for a minim...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to scheduled maintenance information for service interv...

• Add Motorcraft Premium Gold Engine Coolant(yellow-colored), VC-7–A (U.S., except CA, OR and NM),VC-7–B (CA, OR and NM), meeting Ford SpecificationWSS-M97B51–A1. Note: Use of Motorcraft Cooling System Stop Leak Pellets, VC-6, may darken the color of Motorcraft Premium Gold Engine Coolant fromyellow...

2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the coolant reservoir (a translucent plastic bottle).Slowly turn cap counterclockwise (left) until pressure begins to release. 3. Step back while the pressure releases. 4. When you are sure that all the pressure ...

Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Refill capacities in this section. Fill your engine coolant reservoir as outlined in Adding engine coolant in this section. Severe climates If you drive in extremely cold climates (less than –34° F [–3...

How fail-safe cooling works If the engine begins to overheat: • The engine coolant temperaturegauge will move to the red (hot)area. • The “Check Engine” indicatorlight will illuminate. If the engine reaches a presetover-temperature condition, the engine will automatically switch toalternating cylind...

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tankmay cause leakage and lead to fuel spray and fire. The fuel system may be under pressure. If the fuel filler cap isventing vapor or if you hear a hissing sound, w...

• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek medical attention. Failure to seek proper medical attention couldlead to permanent injury. • Fuels can also be harmful if absorbed through the skin. If f...

• Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including thecargo area). • Keep the fuel pump nozzle in contact with the fuel container whilefilling. • DO NOT use a device that would hold the fuel pump handle in the fillposition. Fuel Filler...

The advertised capacity is the amount of the indicated capacity and theempty reserve combined. Indicated capacity is the difference in theamount of fuel in a full tank and a tank when the fuel gauge indicatesempty. Empty reserve is the small amount of fuel remaining in the fueltank after the fuel ga...

Keep a record for at least one month and record the type of driving (cityor highway). This will provide an accurate estimate of the vehicle’s fueleconomy under current driving conditions. Additionally, keeping recordsduring summer and winter will show how temperature impacts fueleconomy. In general,...

• Perform all regularly scheduled maintenance items. Follow therecommended maintenance schedule and owner maintenance checksfound in scheduled maintenance information. Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economyat any speed. • Carrying unnecessary weight may re...

POWER STEERING FLUID Check the fluid. Refer to the scheduled maintenanceinformation for service maintenance schedules. 1. Start the engine and let it rununtil it reaches normal operatingschedules. 2. Turn the steering wheel left andright several times. 3. Turn the engine off. 4. Check the fluid leve...

CLUTCH FLUID (IF EQUIPPED) The clutch master cylinder andbrake master cylinder are part ofthe same system; both are refillablethrough the brake master cylinderwith brake fluid. For moreinformation on brake fluidmaintenance, refer to Brake fluid in this chapter. Brake fluid is toxic. If brake fluid c...

Use of a non-approved automatic transmission fluid may causeinternal transaxle component damage. If necessary, add fluid in 1/2 pint (250 mL) increments through the fillertube until the level is correct. If an overfill occurs, excess fluidshould be removed by a qualifiedtechnician. An overfill condi...

• Wagon IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic SafetyAdministration Regulations requirethat a Safety ComplianceCertification Label be affixed to avehicle and prescribe where theSafety Compliance CertificationLabel may be located. The SafetyCompliance Certification ...

Vehicle identification number (VIN) The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Please note thatin the graphic XXXX isrepresentative of your vehicleidentification number.) The Vehicle Identification Number (VIN) contains the followin...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford or Ford of Canada dealer.These quality accessories have been specifically engineered to fulfill yourautomotive needs; they are custom designed to co...

Leather wrapped steering wheels Scuff plates Speed control Lifestyle Bike racksCargo organization and management Peace of mind First aid and highway safety kitsFull vehicle coversLocking gas capNavigation systemsRemote startVehicle security systems For maximum vehicle performance, keep the following...

A Air cleaner filter .......................205 Airbag supplementalrestraint system ..............83–84, 90 and child safety seats ..............85description ..........................84, 90disposal ......................................92driver airbag ........................85, 91indicator light ...