Ford 2005 F-150 v.1- Manuals

Warning symbols on your vehicle When you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempting adjustmentof any kind. Protecting the environment We must all play our part inprotecting the environment. Correctvehicle usage and the authorizedd...

Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, steering or brake...

Front seat mounted rear-facing child or infant seats should NEVER be placed in front of an active passenger air bag. Using your vehicle with a snowplow For more information and guidelines for using your vehicle with asnowplow, refer to the Driving chapter. F150 SuperCrew Owners: Snowplowing Your veh...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -No...

WARNING LIGHTS AND CHIMES Base instrument cluster Base with Tachometer instrument cluster Mid instrument cluster REVIEW COPY 2005 F150 (f12) , Owners Guide (post-2002-fmt) (own2002) , Market: USA_English (fus) Instrument Cluster Instrument Cluster 10

Luxury instrument cluster Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

On vehicles equipped with a message center, “ENGINE FAILSAFEMODE” will be displayed, refer to Message Center in the Driver Controls chapter. Brake system warning light: To confirm the brake system warning light is functional, it will momentarily illuminate when the ignition isturned to the ON positi...

immediately. A chime will also sound when a malfunction in thesupplemental restraint system has been detected. Safety belt: Reminds you to fasten your safety belt. A chime will alsosound to remind you to fasten yoursafety belt. Charging system: Illuminates when the battery is not charging properly. ...

High beams: Illuminates when the high beam headlamps are turned on. MINI MESSAGE CENTER WARNING DISPLAYS (IF EQUIPPED) Door ajar: Displays when the ignition is in the ON position andany door is open. Low fuel: Displays when the fuel level in the fuel tank is at or nearempty (refer to Fuel gauge in t...

Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in the ignition) and thedriver’s door is opened. GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperaturegauge: Indicates engine coolant temperature. At norma...

Odometer: Registers the total miles (kilometers) of the vehicle. • With Mini Message Center • With Full Message Center Refer to Message Center in theDrivers Controls chapter on how toswitch the display from Metric toEnglish. Trip odometer: Registers the miles (kilometers) of individual journeys. • W...

Engine oil pressure gauge: Indicates engine oil pressure. Theneedle should stay in the normaloperating range (between “L” and“H”). If the needle falls below thenormal range, stop the vehicle, turnoff the engine and check the engineoil level. Add oil if needed. If the oil level is correct, have your ...

FORD AM/FM STEREO SYSTEM (IF EQUIPPED) 1. / Tune: Press to manually go up or down the radio frequency.Also use in menu mode to selectvarious settings. 2. Audio: Press to access select various settings. Treble: Press to adjust the treble setting. Use / / SEEK, SEEK . Bass: Press to adjust the bass se...

FORD SINGLE CD SOUND SYSTEM (IF EQUIPPED) 1. / Tune: Press to manually go up or down the radio frequency.Also use in menu mode to selectvarious settings. 2. Phone/mute: Press to mute the playing media. Press again to returnto the playing media. 3. Menu: Press to toggle through the following modes: T...

Fade: Press to adjust the audio between the front and rear speakers. Use / / SEEK, SEEK . Speed sensitive volume: Radio volume automatically changes slightly with vehicle speed to compensate for road and wind noise. Use / / SEEK, SEEK to adjust. Autoset: Allows you to set the strongest local radio s...

FORD DUAL MEDIA SOUND SYSTEM (IF EQUIPPED) 1. / Tune: Press to manually go up or down the radio frequency.Also use in menu mode to selectvarious settings. 2. Seek: Press to access the next strong station or track. 3. Phone/mute: Press to mute the playing media. Press again to returnto the playing me...

10. Repeat: Press to repeat the current CD track. 11. Fast forward: Press to manually advance in a tape or CDtrack. 12. Rewind: Press to manually reverse in a tape or CD track. 13. Memory presets: To set a station: Select frequency bandAM/FM; tune to a station, press andhold a preset button until so...

Show functions.To activate, press and hold MENU until TRAFFIC appears in the display.This indicates RDS is active. Press MENU consecutively to scroll throughTraffic, Find, Show or RDS ON. Use SEEK, SEEK to activate/deactivate the functions. To deactivate RDS, scroll to RDS ONand press SEEK, SEEK so ...

Traffic : Allows you to hear traffic broadcasts. Use / to turn on/off, then use SEEK or SCAN to find a station broadcasting a traffic report (if it is broadcasting RDS data). Traffic information is not available in most U.S. markets. RDS : Press MENU consecutively to scroll through RDS Find Program ...

11. Rewind: Press to manually reverse in a CD track. 12. Memory presets: To set a station: Select frequency bandAM/FM; tune to a station, press andhold a preset button until sound returns. 13. Scan: Press for a brief sampling of radio stations or CD tracks. Pressagain to stop. 14. Seek: Press to acc...

RADIO FREQUENCIES AM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio and TelecommunicationsCommission (CRTC). Those frequencies are: AM - 530, 540–1700, 1710 kHz FM- 87.7, 87.9–107.7, 107.9 MHz RADIO RECEPTION FACTORS There are three factors th...

Don’t: • Expose discs to direct sunlight or heat sources for extended periodsof time. • Insert more than one disc into each slot of the CD changer magazine. • Clean using a circular motion. CD units are designed to play commercially pressed 4.75 in (12cm) audio compact discs only. Due to technical i...

HEATER ONLY SYSTEM(IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in thevehicle. 2. Temperature selection: Controls the temperature of theairflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief d...

4. Direct the outer instrument panel vents towards the side windows. To increase airflow to the outer instrument panel vents, close the ventslocated in the middle of the instrument panel. Do not place objects on top of the instrument panel as theseobjects may become projectiles in a collision or sud...

Temperature conversion: To switch between Fahrenheit and Celsius: If your vehicle is equipped with a full message center, refer to Setup menu in the Message center section of the Driver Controls chapter for more information. If your vehicle is equipped with a mini message center, seeyour dealer for ...

engaged manually in any other airflow selection except (defrost). Recirculation may turn off automatically in all airflow selections exceptMAX A/C. 5. A/C control: Press to activate/deactivate air conditioning. Use with recirculated air to improve cooling performance and efficiency. Engagesautomatic...

Automatic Temperature Control (ATC) system with heated seats(if equipped) Temperature conversion: To switch between Fahrenheit and Celsius: If your vehicle is equipped with a full message center, refer to Units (Fahrenheit/Celsius) in the Driver Controls chapter. If your vehicle is equipped with a m...

12. A/C control: Press to activate/deactivate air conditioning. Use with recirculated air to improve cooling performance and efficiency. Engagesautomatically in AUTO, (defrost) and (floor/defrost). 13. OFF: Outside air is shut out and the fan will not operate. 14. Temperature control: Press to incre...

HEADLAMP CONTROL Rotate the headlamp controlclockwise to the first position to turn on the parking lamps. Rotateclockwise to the secondposition to also turn on the headlamps. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights nor...

Foglamp control (if equipped) The headlamp control also operatesthe foglamps. The foglamps can beturned on only when the headlamp control is in the , or position and the high beams are notturned on. Pull headlamp control towards youto turn foglamps on. The foglampindicator light will illuminate if t...

Rear map lamp (if equipped) The rear map lamp lights arelocated on the end of the overheadrail system. The lamps can beturned on or off by pushing on thelens. Dome/courtesy lamps (if equipped) The dome lamp lights when: • any door is opened. • the instrument panel dimmerswitch is rotated up until th...

2. At the top and inboard side of theheadlamp, loosen the three retainingscrews. 3. Once the three retaining screwshave been removed, disengage thetab at the top center of theheadlamp assembly by lifting it up. 4. Slide headlamp assembly forwarddisconnecting the snap attachmentat the fender and disc...

Replacing front parking lamp/turn signal/sidemarker bulbs 1. Make sure the headlamp controlis in the OFF position and open thehood. 2. At the top and inboard side of theheadlamp, loosen the three retainingscrews. 3. Once the three retaining screwshave been removed, disengage thetab at the top center...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick pus...

1. To open the bins, move thecenter latch forward which willallow the door to be opened. 2. The latches on the side of thebins are to enable the user toremove the bin or add a dealerpurchased feature. Sliding the bins on the rails maycause damage to the headliner.The removable bins are to besnapped ...

While pushing upwards with palms, grip the side latches with fingers andsqueeze. With pressure applied with palms and side latches squeezed down, pulldownward on the entire storage bin and remove. AUXILIARY POWER POINT Power outlets are designedfor accessory plugs only. Do not hang any type of acces...

CELL PHONE USE The use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,drivers must not compromise their own or others’ safety when usingsuch equipment. Mobile Communications can enhance personal safetyand security when app...

One touch down Allows the driver’s window to openfully without holding the controldown. Press completely down onthe bottom part of the rocker switchand release quickly. Press the toppart of the rocker switch to stop. Window lock (if equipped) The window lock feature allows onlythe driver to operate ...

Accessory delay (if equipped) With accessory delay, the window switches may be used for up to tenminutes after the ignition switch is turned to the OFF position or untilany door is opened. MIRRORS Automatic dimming inside rear view mirror (if equipped) Your vehicle is equipped with aninside rear vie...

Heated outside mirrors (if equipped) Heated mirrors remove ice, mist andfog. To activate the heated mirrors,press the rear defrost button R located on the climate control panel. Refer to Rear Window Defrost in the Climate Controls chapter for more information. On vehicles not equipped with reardefro...

Fold-away mirrors Fold the side mirrors in carefullybefore driving through a narrowspace, like an automatic car wash. If equipped with powerfold mirrors,you can fold the side mirrors usingthe power mirror switch. 1. Rotate the switch to thecenter/neutral position. 2. Momentarily pull the switchrearw...

SPEED CONTROL (IF EQUIPPED) With speed control set, you can maintain a speed of 30 mph (48 km/h)or more without keeping your foot on the accelerator pedal. Speedcontrol does not work at speeds below 30 mph (48 km/h). Do not use the speed control in heavy traffic or on roads thatare winding, slippery...

• Depress the brake pedal until thedesired vehicle speed is reached,press the SET control. Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal or the clutch pedal (if equipped). This willnot erase your vehicle’s previously set speed, if RES/RESUME is...

In CD mode: • Press MEM to select the next selection on the CD. In any mode: • Press VOL + or − to adjustvolume. Climate control features Press TEMP + or - to adjusttemperature. Press FAN + or - to adjust fanspeed. MOON ROOF (IF EQUIPPED) The moon roof control is located on the overhead console. Do ...

U.S. federal safety standards (this includes any garage door openermodel manufactured before April 1, 1982). A garage door which cannotdetect an object, signaling the door to stop and reverse, does not meetcurrent U.S. federal safety standards. For more information, contactHomeLink 威 at: www.homelin...

4. The indicator light will flash slowly and then rapidly. Release bothbuttons when the indicator light flashes rapidly. (The rapid flashing lightindicates acceptance of the hand-held transmitters’ radio frequencysignals.) 5. Press and hold the just-trained HomeLink 威 button and observe the indicato...

• Continue to press and hold the HomeLink 威 button (note Step 3 in the “Programming” section) while you press and release — every two seconds (“cycle”) your hand-held transmitter until the frequency signal has been accepted by the HomeLink 威 . The indicator light will flash slowly and then rapidly a...

2. The indicator light will begin to flash after 20 seconds. Withoutreleasing the HomeLink 威 button, follow Step 2 in the “Programming” section. For questions or comments, contact HomeLink 威 at www.homelink.com or 1–800–355–3515. MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position,the ...

DTE is calculated using a running average fuel economy, which is basedon your recent driving history of 500 miles (800 km). This value is notthe same as the average fuel economy display. The running average fueleconomy is reinitialized to a factory default value if the battery isdisconnected. Averag...

System warnings System warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems. In the event of a multiple warning situation, the message center willcycle the display to show all warnings by displaying each one for 4seconds. The message center will display the last...

• Auto locks • Brake fluid • Compass • Outside temperature • Engine sensor Contact your dealer as soon as possible if these messages occur on aregular basis. MINI MESSAGE CENTER ELECTRONIC COMPASS/TEMPERATUREDISPLAY (IF EQUIPPED) Outside air temperature The outside temperature display iscontained in...

Compass zone adjustment 1. Determine which magnetic zoneyou are in for your geographiclocation by referring to the zonemap. 2. Turn ignition to the ON position. 3. Start the engine. 4. Press the ODO reset button inthe cluster, hold for six seconds andrelease. You will see that ZONEappears in the ins...

TAILGATE LOCK (IF EQUIPPED) Your vehicle may be equipped with atailgate lock designed to preventtheft of the tailgate. • Insert ignition key and turn to theright to engage lock. • Turn ignition key to the left tounlock. TAILGATE REMOVAL Your tailgate is removable to allowmore room for loading. 1. Lo...

BED EXTENDER (IF EQUIPPED) Your vehicle may be equipped with a bed extender designed to extendthe pickup box for longer loads. To extend the bed extender: 1. Lower tailgate. 2. Pull the round knobs on each sideof the extender to release it fromthe pickup box. 3. Pivot extender on to the tailgate. 4....

KEYS The key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer. You should always carry a second key with you in a safe place in caseyou require it in an emergency. Refer to the SecuriLock 娂 passive anti-theft system section in this chapter for more ...

The (lock) and (unlock) features will work again after: • a door has become ajar, • the ignition is turned to the 3 (ON) position, or • using the UNLOCK control on your remote entry transmitter or unlocking via the keyless entry keypad. Deactivating/activating power door lock/unlock disable feature ...

Memory feature (if equipped) The remote entry system can also control the memory feature. Press the control once to unlock the driver’s door. Pressing the control will automatically move the seat and adjustable pedals to thedesired memory position (the memory position corresponds to thetransmitter b...

Programming remote transmitters It is necessary to have all (maximum of six — original and/or new) of your remote transmitters available prior to beginning this procedure. Ifall remote entry transmitters are not present during the programmingprocedure, the transmitters that are not present during pr...

The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. The battery saver will shut off the interior lamps 30 minutes after thelast door is closed, even if the dimmer control is on. Perimeter lighting feature (if equipped) The perimeter ligh...

4. Pressing the power door control two times again will turn the feature ON if it was previously OFF, or OFF if it was previously ON.Every two consecutive presses of the control after successfully entering the configuration mode will change the enable/disable conditionof the feature. 5. Turn the ign...

Power door unlock/lock procedure You must complete Steps 1–5 within30 seconds, or the procedure willhave to be repeated. If theprocedure needs to be repeated,you must wait a minimum of 30seconds to begin again. 1. Turn the ignition to the 3 (ON)position, then press the control three times. 2. Turn t...

Your personal code is now erased and only the factory set 5–digit codewill work. Antiscan feature The keyless entry keypad is equipped with an anti-theft function called“antiscan.” The antiscan feature provides a one-minute lockout feature,where the user is unable to enter the vehicle using the keyp...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Adjustable head restraints Head ...

Front seat • Lift the track release bar to movethe seat forward or rearward.Make sure that the seat isrelatched into place. • Pull the release lever handlelocated on the side of the seat upto move the seat back forward orbackward. Using the armrest (if equipped) Push the release control to movethe a...

1. Pull control to release seatcushion. 2. Rotate seat cushion up until itlocks into vertical storage position. Returning the seat to seating position Before returning the seatback to its original position, make surethat cargo or any objects are not trapped underneath the seatback. After returning t...

position. The system is designed to help protect smaller drivers sittingclose to the driver air bag by providing a lower air bag output level. Front passenger sensing system For air bags to do their job they must inflate with great force, and thisforce can pose a potentially deadly risk to occupants...

Safety restraints precautions Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. To reduce the risk of injury, make sure children sit in the backseat where they can be properly restrained. Never let a passenger hold a child on his or her lap while thevehic...

Safety belts and seats can become hot in a vehicle that has beenclosed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child anywhere near them. Combination lap and shoulder belts 1. Insert the belt tongue into theproper buckle (the buckle closest...

If the belt has been disconnected to carry large objects behind the seat,reconnect it as follows: 1. Remove the belt from thestowage clip on the back panel. 2. Buckle the small tongue on theend of the belt into the mini-buckleon the driver’s side. The belt is nowready for use. This mini-buckleshould...

1. To lengthen the lap belt, pullsome webbing out of the shoulderbelt retractor. 2. While holding the webbing belowthe tongue, grasp the tip (metalportion) of the tongue so that it isparallel to the webbing and slide thetongue upward. 3. Provide enough lap belt length so that the tongue can reach th...

Energy management retractors Your vehicle has a seat belt system equipped with energy managementretractors at the driver and front outboard passenger seating positions. An energy management retractor is a device which pays out webbing in acontrolled manner. This feature is designed to help further r...

After any vehicle collision, the safety belt systems at all outboardseating positions (except the driver position, which does not have this feature) must be checked by a qualified technician to verifythat the automatic locking retractor feature for child seats is stillfunctioning properly. In additi...

sensors provide information to the Personal Safety System which canthen adapt the air bag deployment or safety belt pretensioner activationbased upon safety belt usage. The Personal Safety System provides the most benefit to beltedoccupants. The system monitors and tailors the air bag deployment bas...

Lap belts Adjusting the lap belt The lap belt should fit snugly and as low as possible around thehips, not across the waist. The front center lap belt tongue is designed to fit only in the correctbuckle. The tongue will not securely latch if you attempt to use it in anyof the outboard seating positi...

The following are reasons most often given for not wearing safety belts:(All statistics based on U.S. data) Reasons given... Consider... “Crashes are rareevents” 36700 crashes occur every day. The more we drive, the more we are exposed to “rare” events,even for good drivers. 1 in 4 of us will be ser...

Do not sit on top of a buckled safety belt to avoid the BeltMinder chime. Sitting on the safety belt will increase the risk of injury in an accident. To disable (one-time) or deactivate the BeltMinder feature please follow the directions stated below. One time disable If at any time the driver/front...

• After step 3, the restraint system warning light (airbag light) will beturned on for three seconds. 4. Within 10 seconds of the light turning on, buckle then unbuckle thesafety belt. • This will disable the BeltMinder 娂 feature for that seating position if it is currently enabled. As confirmation,...

Failure to inspect and if necessary replace the safety beltassembly under the above conditions could result in severe personal injuries in the event of a collision. For proper care of soiled safety belts, refer to Interior in the Cleaning chapter. AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) 1. Air b...

crash severity are appropriate to activate these devices. Refer to the Personal Safety System section in this chapter. The front passenger air bag is not designed to offer protection toan occupant in the center front seating position. Modifying or adding equipment to the front end of the vehicle(inc...

vehicle. This arrangement provides lap and shoulder belt protection forall occupants, and air bag protection for the adults. A child or infantrestrained in the center front seat is not at risk of serious injury from theair bags. How does the air bag supplemental restraint system work? The air bag SR...

Several air bag system components get hot after inflation. Do nottouch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in acollision. Determin...

Objects Pass Airbag OffIndicator Light Passenger Airbag Empty seat Unlit Disabled Small (i.e. 3 ringbinder, small purse,bottled water) Unlit Disabled Medium (i.e. heavybriefcase, fully packedluggage) Lit Disabled Empty seat, Small ormedium object withsafety belt buckled Lit Disabled In case there is...

Important child restraint precautions You are required by law to use safety restraints for children in the U.S.and Canada. If small children (generally children who are four years oldor younger and who weigh 40 lb. [18 kg] or less) ride in your vehicle, youmust put them in safety seats made especial...

To improve the fit of both the lap and shoulder belt on children whohave outgrown child safety seats, Ford Motor Company recommends useof a belt-positioning booster. Booster seats position a child so that safety belts fit better. They lift thechild up so that the lap belt rests low across the hips a...

• Those with a high back. If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boosterseat would be a better choice. Both can be used in any vehicle in a seating position equipped withlap/shoulder belts if your child is over 40 lb....

SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all of the manufacturer’s instructions with thesafety seat you put in your vehicle. If you do not install and use thesafety seat properly, the ...

tether anchors. For more information on top tether straps and anchors,refer to Attaching safety seats with tether straps in this chapter. For more information of LATCH anchors refer to Attaching safety seats with LATCH (Lower Anchors and Tethers for Children) attachments in this chapter. Carefully f...

2. Place the child safety seat in the center seating position. 3. Route the tongue and webbing through the child seat according to thechild seat manufacturer’s instructions. 4. Insert the belt tongue into the proper buckle for the center seatingposition until you hear a snap and feel it latch. Make ...

• F150 Regular Cab • F150 SuperCrew and SuperCab Front seat tether strap attachment 1. Position the child safety seat on the seat cushion. 2. Route the child safety seat tether strap over the back of the seat andunder the head restraint. 3. Locate the correct anchor for the selected seating position...

4. Clip the tether strap to the anchor as shown. • Front seat Regular Cab passengerside • Front seat Regular Cab center(located on back panel) If the tether strap is clippedincorrectly, the child safety seat may not be retained properlyin the event of a collision. 5. Install the child safety seat ti...

If the safety seat is not anchored properly, the risk of a childbeing injured in a collision greatly increases. Rear seat tether strap attachment There are three loops of webbingjust above the back of the rear seat(along the bottom edge of the rearwindow) in the SuperCab andSuperCrew. These loops ar...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

Power is supplied to all four wheelsthrough a transfer case or powertransfer unit. 4WD vehicles allowyou to select different drive modesas necessary. Information on shiftingprocedures and maintenance can befound in your Owner’s Guide . You should become thoroughly familiarwith this information befor...

Every day before you drive, checkyour tires. If one looks lower thanthe others, use a tire gauge to checkpressure of all tires and adjust ifrequired. At least once a month and beforelong trips, inspect each tire andcheck the tire pressure with a tiregauge (including spare, if equipped).Inflate all t...

Always inflate your tires to the Ford recommended inflation pressureeven if it is less than the maximum inflation pressure information foundon the tire. The Ford recommended tire inflation pressure is found onthe tire label or certification label which is located on the B-Pillar or theedge of the dr...

5. Repeat this procedure for each tire, including the spare. Note: Some spare tires require higher inflation pressure than the other tires. Check the tire label on the B pillar or the edge of the driver’s doorfor the recommended spare tire pressure.6. Visually inspect the tires to make sure there ar...

“Temporary Use Only” molded into the tire sidewall or it may be a fullsize dissimilar spare tire/wheel that is different in brand, size orappearance from the road tire, which will be identified with a “Caution”label on the wheel. Both of these spare tires are considered “temporary”.Replace these tem...

Tool Location Spare tire Under the vehicle, just forward ofthe rear bumper Jack, jack handle and lug nut wrench Regular Cab: Behind the interiortrim on the passenger side of thecabSuperCrew and SuperCab: Underthe rear seat on the passenger side Removing the spare tire 1. Use the ignition key to remo...

3. Turn the jack handle clockwise until the tire is raised to its stowedposition underneath the vehicle. The effort to turn the jack handleincreases significantly and the spare tire carrier ratchets or slips whenthe tire is raised to the maximum tightness. Tighten to the best of yourability, to the ...

7. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods oftime under a standard condition of load and inflation pressure. The tireson your vehicle may operate at different conditions for load and inflationpressure. The...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

Safety practices Driving habits have a great deal to do with your tire mileage and safety. • Observe posted speed limits • Avoid fast starts, stops and turns • Avoid potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow,...

The tires should also be balanced periodically. An unbalanced tire andwheel assembly may result in irregular tire wear. Tire rotation Rotating your tires at the recommended interval (as indicated in the Scheduled Maintenance Guide that comes with your vehicle) will help your tires wear more evenly, ...

Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weigh...

GVW (Gross Vehicle Weight) – is the Vehicle Curb Weight + cargo + passengers. GVWR (Gross Vehicle WeightRating) – is the maximum allowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo). The GVWR is shown on theSafety Compliance CertificationLabel located o...

Exceeding any vehicle weight rating limitation could result inserious damage to the vehicle and/or personal injury. Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargoshould never exceed XXX pounds” on your vehicle’s placard. 2. Determine...

transport the cement to your home? If you and your friend eachweighed 220 lb. (100 kg), the calculation would be: 1400 – (2 x 220) –(12 x 100) = 1400 – 440 – 1200 = – 40 lb. Metric conversion; 636 kg –(2 x 100) – (12 x 45) = 636 – 200 – 540 = –104 kg. No, you do nothave enough cargo capacity to carr...

Towing a trailer places an additional load on your vehicle’s engine,transmission, axle, brakes, tires and suspension. Inspect thesecomponents carefully periodically during, and after any towing operation. Exceeding the maximum GCWR could result in extensive damageto your vehicle and personal injury....

Crew Cab 4x4 (139” wheelbase) Engine Rear axle ratio Maximum GCWR-lb. (kg) Maximum trailer weight-lb. (kg) 4.6L 3.73 12200 (5534) 6500 (2948) 5.4L (with 17” tires) 3.55 14000 (6350) 8200 (3719) 5.4L (with 18” tires) 3.55 13500 (6123) 7700 (3493) 5.4L (with 17” tires) 3.73 15000 (6804) 9200 (4173) 5....

3. Attach the trailer to the vehicle and adjust the hitch equalizers so thatthe front bumper height is within 1 ⁄ 2 ” (13 mm) of the reference point. After proper adjustment, the rear bumper should be no higher than inStep 2. Note: Adjusting an equalizing hitch so the rear bumper of the vehicle is h...

Driving while you tow When towing a trailer: • Turn off the speed control. The speed control may shut offautomatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer. • To eliminate excessive shifting, use a lower gear. This will ...

STARTING Positions of the ignition 1. OFF/LOCK, locks the steeringwheel, automatic transmissiongearshift lever and allows keyremoval. Note: The ignition key can not be removed from the ignition unlessthe gearshift lever is securelylatched in P (Park). 2. ACCESSORY, allows the electricalaccessories s...

Note: If the engine does not start within five seconds on the first try, turn the key to OFF, wait 10 seconds and try again. If the engine stillfails to start, press and hold the accelerator to the floor and try again;this will allow the engine to crank with the fuel shut off in case theengine is fl...

Base instrument cluster withand without tachometer Mid and Luxury instrumentcluster Parking brake To set the parking brake (1), pressthe parking brake pedal down untilthe pedal stops. The BRAKE warning lamp will illuminate and will remain illuminateduntil the parking brake is released. Base instrume...

Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any morethan low-slung sports cars are desig...

2. Open the center console bin.Using a screwdriver, carefully pry offthe console finish panel surroundingthe shifter mechanism by inserting ascrewdriver into the latch slot asshown. 3. Remove console finish panelassembly to expose the inside of thegearshift. 4. Press and hold the white buttonlocated...

• Allows upshifts by moving gearshift lever. • Will not downshift into 1 (First) at high speeds; allows for 1 (First)when vehicle reaches slower speeds. Forced downshifts • Allowed in D (Overdrive) or Drive. • Depress the accelerator to the floor. • Allows transmission to select an appropriate gear....

Maximum downshift speeds 1 4 - 3 45 mph (72 km/h) 17 mph (27 km/h) 3 - 2 35 mph (56 km/h) 13 mph (21 km/h) 2 - 1 20 mph (32 km/h) 7 mph (11 km/h) 1 Downshift at lower speeds when driving on slippery surfaces. Reverse 1. Make sure that your vehicle is at a complete stop before you shift intoR (Revers...

REVERSE SENSING SYSTEM (IF EQUIPPED) The Reverse Sensing System (RSS) sounds a tone to warn the driver ofobstacles near the rear bumper when the R (Reverse) is selected and thevehicle is moving at speeds less than 3 mph (5 km/h). The system is noteffective at speeds above 3 mph (5 km/h) and may not ...

If your vehicle sustains damage to the rear bumper/fascia, leavingit misaligned or bent, the sensing zone may be altered causinginaccurate measurement of obstacles or false alarms. FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) For important information regarding safe operation of this typeof vehicl...

N (Neutral) – No power to either front or rear wheels. 4L (4WD Low) – Uses extra gearing to provide maximum power to all four wheels at reduced speeds. Intended only for off-road applicationssuch as deep sand, steep grades or pulling heavy objects. 4L (4WD Low)will not engage while the vehicle is mo...

Do not leave the vehicle unattended with the transfer case in theN (Neutral) position. Always set the parking brake fully and turn off the ignition when leaving the vehicle. Using the electronic shift 4WD system (if equipped) 2H (2WD High) - Power to the rear wheels only; used for street and highway...

3. On vehicles equipped with an automatic transmission, place thetransmission in N (Neutral); on vehicles equipped with a manualtransmission, depress the clutch. 4. Move the 4WD control to the desired position. • If shifting into 4L (4WD Low), wait for the 4X4 LOW light in theinstrument cluster to t...

• Be extremely careful when driving on pavement made slippery byloose sand, water, gravel, snow or ice. If your vehicle goes off the edge of the pavement • If your vehicle goes off the edge of the pavement, slow down, butavoid severe brake application, ease the vehicle back onto thepavement only aft...

Emergency maneuvers • In an unavoidable emergency situation where a sudden sharp turnmust be made, remember to avoid “over-driving” your vehicle, i.e.,turn the steering wheel only as rapidly and as far as required to avoidthe emergency. Excessive steering will result in less vehicle control,not more...

Mud and water If you must drive through highwater, drive slowly. Traction orbrake capability may be limited. When driving through water,determine the depth; avoid waterhigher than the bottom of the hubs(if possible) and proceed slowly. Ifthe ignition system gets wet, thevehicle may stall. Once throu...

slopes or hills . A danger lies in losing traction, slipping sideways and possibly rolling over. Whenever driving on a hill, determine beforehandthe route you will use. Do not drive over the crest of a hill withoutseeing what conditions are on the other side. Do not drive in reverseover a hill witho...

Avoid sudden applications of power and quick changes of direction onsnow and ice. Apply the accelerator slowly and steadily when startingfrom a full stop. Avoid sudden braking as well. Although a 4WD vehicle may acceleratebetter than a two-wheel drive vehicle in snow and ice, it won’t stop anyfaster...

engine’s air intake and severely damage your engine or your vehicle maystall. Driving through deep water where the transmission vent tube is submerged may allow water into the transmission andcause internal transmission damage. Once through the water, always dry the brakes by moving yourvehicle slow...

pressure for the tire and associated load rating is imprinted on the tiresidewall. Tire air pressure may require re-adjustment within thesepressure limits to accommodate the additional weight of the snowplowinstallation Operating the vehicle with the snowplow attached Ford recommends that the F–150 ...

• Shift transfer case to 4H (4WD High) when plowing larger areas orlight snow at higher speeds. Do not exceed 15 mph (24 km/h). • Do not shift the transmission from a forward gear to R (Reverse) untilthe engine is at idle and the wheels are stopped. • If the vehicle is stuck, shift the transmission ...

GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the New Vehicle Limited...

Canadian customers who require roadside assistance, call1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford MotorCompany will reimburse a reasonable amount. To obtain reimbursementinformation, U.S. Ford or Mercury vehicles customers call1-800-241-3673; Lincoln vehicle custo...

This switch is located in the frontpassenger’s footwell, behind the kickpanel access cover, in front of thefuse box. The access cover needs tobe removed to reset the fuel pumpshut-off switch. To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are appare...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 10A* Run/Accessory - Wipers, Instrumentcluster 2 20A* Stop/Turn lamps, Speed control deactivateswitch 3 5A* Power mirrors, Memory logic power,Memory seats and pedals 4 10A* DVD battery ...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description R203 Half ISO relay PCM * Mini fuses ** Cartridge fuses Auxiliary relay box The relay box is located in the engine compartment on the left fender. • With Daytime Running Lamp (DRL) and 4x4 options • Without Daytime Runn...

5. Turn the heater fan on in both vehicles to protect any electricalsurges. Turn all other accessories off. Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate t...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In ...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. Ford recommends your vehicle be towed with a wheel lift or flatbed. Donot tow with a slingbelt. Ford Motor C...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handling your vehicle linewill provide warranty service, we recommend you return to your sellingdealer who wants to ensure your continued satisfaction. Pl...

THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes. • available free to owners and lessees of qualifying Ford Motor Companyvehicles. The Dispute Settlement Board may not be available in all states. FordMot...

Board membership The Board consists of: • Three consumer representatives • A Ford or Lincoln/Mercury dealership representative Consumer candidates for Board membership are recruited and trained byan independent consulting firm. The dealership Board member is chosenfrom Ford and Lincoln Mercury deale...

Oral presentations If you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral presentationbefore the Board, this is not a requirement and the Board will decide thecase whether or not an oral presentation is made. An oral prese...

unsatisfactory, Ford of Canada participates in an impartial third partymediation/arbitration program administered by the Canadian MotorVehicle Arbitration Plan (CAMVAP). The CAMVAP program is a straight-forward and relatively speedyalternative to resolve a disagreement when all other efforts to prod...

Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website:www.helminc.com. (Items in this catalog may be purchased by credit card, check ormoney order.) Obtaining a French owner’s guide Fre...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is availablefrom your dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can discolor and s...

PAINT CHIPS Your dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jam) toyour dealer to ensure you get the correct color. • Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and in...

• 5.4L engine • Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your dealer. • For routine cleaning, use Motorcraft Detai...

Do not use sharp objects, such as a razor blade, to clean theinside of the rear window or to remove decals, as it may causedamage to the rear window defroster’s heated grid lines (ifequipped). INSTRUMENT PANEL AND CLUSTER LENS Clean the instrument panel with a damp cloth, then dry with a dry cloth. ...

Do not use cleaning solvents, bleach or dye on the vehicle’sseatbelts, as these actions may weaken the belt webbing. LEATHER SEATS (IF EQUIPPED) Your leather seating surfaces have a clear, protective coating over theleather. • To clean, use a soft cloth with Motorcraft Deluxe Leather and VinylCleane...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a scheduled maintenance guide which makes trackingroutine service easy. If your vehicle requires professional service, your dealership can providethe...

• Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N(Neutral). 2. Block the wheels. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease h...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.2L V6 engine 1. Battery 2. Clutch fluid reservoir (manual transmission) 3. Power steering fluid reservoir 4. Brake fluid reservoir 5. Engine coolant reservoir 6. Air filter assembly 7. Engine oil filler cap 8. Engine oil dipstick 9. Transmission flu...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16–A2.Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic c...

• If the oil level is between the MIN and MAX marks, the oil level is acceptable. DO NOT ADD OIL. • 4.2L V6 engine • 4.6L/5.4L V8 engine • If the oil level is below the MINmark, add enough oil to raise thelevel within the MIN-MAX range. • Oil levels above the MAX mark may cause engine damage. Some o...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. However, for severe usage or in high temperature climates, check thebattery electrolyte level. Refer to the Scheduled Maintenance Guide for the service...

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.Lift the battery with a battery carrier or with your hands on oppositecorners. Keep batteries out of reach of ...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to the Scheduled Maintenance Guide for service interval...

Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine...

To reduce the risk of personal injury, make sure the engine iscool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come outforcefully when the cap is loosened slightly. 1. Before you begin, turn the engine off and let it cool. 2. When...

Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Refill capacities in this section. Fill your engine coolant reservoir as outlined in Adding engine coolant in this section. Severe climates If you drive in extremely cold climates (less than –34° F [–3...

Never remove the coolant reservoir cap while the engine isrunning or hot. 5. Restart the engine and take your vehicle to a service facility. Driving the vehicle without repairing the engine problemincreases the chance of engine damage. Take your vehicle to aservice facility as soon as possible. WHAT...

Use the following guidelines to avoid static build-up when filling anungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including thecargo area). • Keep the fuel pump nozzle in contact with the fuel container whilefill...

Many of the world’s automakers approved the World-wide Fuel Charterthat recommends gasoline specifications to provide improvedperformance and emission control system protection for your vehicle.Gasolines that meet the World-wide Fuel Charter should be used whenavailable. Ask your fuel supplier about...

Filling the tank The advertised fuel capacity of the fuel tank on your vehicle is equal tothe rated refill capacity of the fuel tank as listed in the Refill capacities section of this chapter. The advertised capacity is the amount of the indicated capacity and theempty reserve combined. Indicated ca...

5. Follow one of the simple calculations in order to determine fueleconomy: Calculation 1: Divide total miles traveled by total gallons used. Calculation 2: Multiply liters used by 100, then divide by total kilometers traveled. Keep a record for at least one month and record the type of driving (cit...

Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fueleconomy. • Use recommended engine oil. Refer to Lubricant specifications in this chapter. • Perform all regularly scheduled maintenance items. Follow there...

expected on the vehicle under optimum conditions. Your fuel economymay vary depending upon the method of operation and conditions. EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to comply withapplicabl...

• First, at least 10 minutes of driving on an expressway or highway. • Next, at least 20 minutes driving in stop-and-go, city-type traffic withat least four idle periods. Allow the vehicle to sit for at least eight hours without starting theengine. Then, start the engine and complete the above drivi...

BRAKE FLUID RESERVOIR The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“MAX” lines are within the normaloperating range; there is no need toadd fluid. If the fluid levels areoutside of the normal operating range...

1. Clean the reservoir cap beforeremoval to prevent dirt and waterfrom entering the reservoir. 2. Remove cap and rubberdiaphragm from reservoir. 3. Add fluid until the level reachesthe step in the reservoir. 4. Reinstall rubber diaphragm andcap onto reservoir. TRANSMISSION FLUID Checking automatic t...

Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug andinspect the fluid level. 3. Fluid level should be at bottom ofthe opening. 4. Add enough fluid through thefiller opening so that the fluid levelis at the bottom of the opening. 5. Insta...

Checking and adding transfer case fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug andinspect the fluid level. 3. Add only enough fluid throughthe filler opening so that the fluidlevel is at the bottom of theopening. Use only fluid that meets Ford specifications. Refer to Lubr...

AIR FILTER MAINTENANCE Refer to the scheduled maintenance guide for the appropriate intervalsfor changing the air filter element. When changing the air filter element, use only the Motorcraft air filterelement listed. Refer to Motorcraft part numbers in this chapter. Note: Do not start your engine w...

REFILL CAPACITIES Fluid Ford PartName Application Capacity Brake fluidand clutchfluid MotorcraftHighPerformanceDOT 3MotorVehicleBrake Fluid All Fill to line or step(for clutch) onreservoir Enginecoolant 1 MotorcraftPremiumGold EngineCoolant(yellow-colored) 4.2L V6 engine 20.1 quarts (19.0L) 4.6L V8 ...

MERCON 威 and MERCON 威 V type fluids are not interchangeable. DO NOT mix MERCON 威 and MERCON 威 V. Use of a transmission fluid that indicates dual usage (MERCON 威 and MERCON 威 V) in an automatic transmission application requiring MERCON 威 may cause transmission damage. Use of any fluid other than ther...

LUBRICANT SPECIFICATIONS Item Ford partname orequivalent Ford partnumber Fordspecification Front axle(4X4) Motorcraft SAE75W-90 FuelEfficient HighPerformanceSynthetic RearAxle Lubricant XY-75W90-QFEHP — Rear axle Motorcraft SAE75W-140Synthetic RearAxle Lubricant 1 XY-75W140–QL WSL-M2C192–A Brake flu...

Item Ford partname orequivalent Ford partnumber Fordspecification Hinges, latches,striker plates,fuel filler doorhinge and doorcheck arm Multi-PurposeGrease XG-3 ESE-M1C171–A Lock cylinders Motorcraftpenetrating andlock lubricant Motorcraft XL-1 none Transmission/steering/parkingbrake linkagesand pi...

handle. Check the container to verify the fluid being added is of thecorrect type. Refer to your Scheduled Maintenance Guide to determine the correct service interval. Some transmission fluids may be labeled as dual usage, such asMERCON 威 and MERCON 威 V. These dual usage fluids are not to be used in...

SuperCab Vehicledimensions Styleside 5.5’box - inches(mm) Styleside /Flareside 6.5’box - inches(mm) Styleside 8.0’box - inches(mm) (1) Overalllength 217.8 (5532) 229.8 (5837) 248.4 (6309) (2) Overallwidth 78.9 (2005) 78.9 (2005) 78.9 (2005) (3) Overallheight –4x2/4x4 74.1 (1881) /76.5 (1943) 73.5 (1...

1. World manufacturer identifier 2. Brake type and gross vehicleweight rating (GVWR) 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number Engine number The engine number (the last eight numbers of the vehicle identificationnum...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford or Ford of Canada dealer.These quality accessories have been specifically engineered to fulfill yourautomotive needs; they are custom designed to co...

A Accessory delay ..........................65 Air bag supplemental restraintsystem ........................................128 and child safety seats ............129disposal ....................................131driver air bag ..................129–130indicator light .........................131op...

starting after a collision .........224 Engine block heater .................195 Engine oil ..................................259 checking and adding ..............259dipstick ....................................259filter, specifications ........262, 290recommendations ...................262refill c...