Ford 2005 Escape Hybrid v.2- Manuals

Starting the vehicle • The engine will start and run when you first turn the ignition key tothe start position. • The engine cannot be started in the N (Neutral) position. • Depending upon temperature and the high voltage battery’s state ofcharge, the engine may shut off shortly after starting the v...

• The Escape Hybrid’s hydraulic brake system used for regenerativebraking is different from other vehicles. The noise from the ABS pumpmotor and the brake pedal pulsation are much less than on vehicleswith conventional ABS. Noise and pedal pulsation during ABS may notbe noticed. For more information...

Service Data Recording Service data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehicle. This potentiallyincludes information about the performance or status of various systemsand modules in the vehicle, such as engine, throttle, steering or brake...

Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate thanother types of vehicles. Before you drive your vehicle, please read this Owner’s Guide carefully. Your vehicle is not a passenger car. As with other vehicles of this type,failur...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -No...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to test ...

Under engine misfire conditions, excessive exhaust temperaturescould damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Service soon: Illuminates when the vehicle has detected a malfunction.Report the fault to a dealer at t...

Safety belt: Reminds you to fasten your safety belt. A chime will alsosound to remind you to fasten yoursafety belt. If this light continues toflash the chime will sound again toremind you to fasten your safety belt. Master vehicle electrical hazardwarning lamp: Indicates Hybrid component fault/fail...

Never remove the coolant reservoir cap while the engine isrunning or hot. ABS active/Traction control 娂 active (if equipped): Flashes when the ABS system is active. Ifthe light remains on, have thesystem serviced immediately, referto the Driving chapter for more information. Turn signal: Illuminates...

GAUGES Speedometer: Indicates the current vehicle speed. Battery gauge: Provides information about the vehicle’senergy usage. • ASSIST — Battery provides extrapower to boost the vehicle’sacceleration. • CHARGE — Storing extra energyin the battery when coasting orslowing down. Odometer: Registers the...

PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD (IF EQUIPPED) 1. Power/volume: Press to turn ON/OFF; turn to increase/decreasevolume. 2. SCAN: Press to hear a brief sampling of all listenable stations,tape selections or CD tracks. Pressagain to stop. 3. CD slot: Insert a CD with the label side up. SCAN 2005...

8. BAL (Balance): Press BAL; then press SEL / to shift sound to the right/left speakers. FADE: Press FADE; then press SEL / to shift sound to the front/rear speakers. 9. MENU: Press MENU and SEL to access clock mode, RDS on/off,Traffic, Program type, Show typeand Compression modes. Setting the clock...

AM/FM STEREO IN-DASH SIX CD MODULAR AUDIO (IF EQUIPPED) 1. CD: To begin CD play, press LOAD. When the system is ready toaccept a disc, IN will appear on theradio display. You may then insert a CD. The system will load the CD andbegin play after a short pause. The disc number and track number willill...

• Allow tapes which have been subjected to extreme heat, humidity orcold to reach a moderate temperature before playing. • Clean the cassette player head with a cassette cleaning cartridge after10–12 hours of play to maintain good sound/operation. Don’t: • Expose tapes to direct sunlight, extreme hu...

System overview 1. CD slot: Insert an audio CD, label side up. 2. Eject: Press this control to eject an audio CD or a navigation CD. 3. Navigation (NAV): Press the NAV control to access the navigationsystem menu. 4. MAP: The MAP control works in all modes. Press to show currentlocation. 5. BACK: Thi...

6. ENTER: Use this control when viewing a menu in the navigationsystem. Press the control up ordown, left or right to highlight anitem in the display. Press the centerof the control to make your selection. 7. Memory presets: The memory presets store favorite AM/FMstations and allow you to accessvari...

Quick start – how to get going To play a radio station: 1. Ensure that the ignition and the Vehicle Navigation Radio (VNR)system are ON. 2. Press the AM/FM control to selectthe desired frequency band. 3. Press the SEEK control to locatea station. To play a CD in the VNR: 1. Ensure that the ignition ...

2. Press the NAV control to enterinto Navigation mode. 3. To enter a destination, ensurethat the vehicle is in the PARK position. 4. To navigate to home from thecurrent location, press HOME. If ahome location has not previouslybeen stored, pressing and holdingHOME will store the home location. Energ...

The vehicle is either at rest, or issharing very little power betweenthe Hybrid parts. This can occur athigher speeds if the vehicle is notspeeding up or slowing down. The vehicle is driving in electricmode. (Power is coming from theelectric motors and not the engine). Fuel economy screen Your Vehic...

• Average Fuel Economy (AFE): The AFE is displayed on the white bar across the graph. The AFE will be retained when the key is turnedOFF, and will continue averaging when driving resumes. PressingRESET will reset the AFE to zero. • One minute average graph: The graph is updated each minute with the ...

4. Select AVC. 5. Use the cursor control to increaseor decrease the levels. The higherthe level selected, the greater thecompensation. The levels will beshown in the display. Decrease allthe way to the left to turn AVC off. AM/FM select The AM/FM control works in radio,CD and navigation modes. AM/FM...

Select the TRAF soft key to select traffic information broadcast fromcertain stations which will automatically interrupt radio or CD playbackat a preset volume level. The default Traffic volume can be adjusted withthe slider bar using the cursor input. Moving the position to the left mostposition wi...

2. Insert one disc into each CD trayof the magazine (up to 6 discs).Ensure that the label side is facingup. If you pull too hard on the discholder, the disc holder may comecompletely out of the magazine. Ifthis happens, reinsert the discholder back into the magazine. 3. Insert each CD tray, with the...

Navigation features The route guidance navigation system in your audio unit will not functionunless a navigation CD is inserted. Ensure that you follow highway code restrictions and do not takeany risks. For example, if you are unable to make a U-turn,continue on your journey. The navigation system ...

• Sort by Distance – Lists the closest POI entries to the vehicle’s current location. • Within a Town/City – Lists entries for a specific city in alphabetical order. Note: The intersection function is not available when the vehicle is moving. Certain categories may not be available in some areas and...

5. Use freeways — Creates a route which uses freeways where possible. Route calculation Once the route criteria is selected, the navigation system automaticallycalculates a route to the selected destination. The route appears on thedisplay screen and a voice prompt provides instructions. This screen...

Route interruptions In the course of your destination, you may decide to temporarily leaveyour planned route for gas, food, etc. If you turn off the ignition, theoption to continue the route guidance will be displayed when the ignitionis turned on again. Use the cursor control to select from one of ...

1. Access the CLOCK screen. 2. Press the ADJUST control toselect the hours or minutes to set. 3. Use the cursor control to increaseor decrease the hours or minutes. 4. Press DONE to set the time. 5. Select the SET soft key tosynchronize/set the minutes andseconds to GPS time. The hours will remain a...

MANUAL HEATING AND AIRCONDITIONING SYSTEM 1. Fan speed adjustment: Controls the volume of air circulated in thevehicle. 2. Air flow selections: Controls the direction of the airflow in thevehicle. See the following for a briefdescription on each control. MAX A/C: Uses recirculated air to cool the ve...

Operating tips • To reduce fog build up on the windshield during humid weather, placethe air flow selector in the position. • To reduce humidity build up inside the vehicle in cold weather: do notdrive with the air flow selector in the O (OFF), A/C or MAX A/C position. • Under normal weather conditi...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parking lamps. Rotate to the secondposition to also turn on the headlamps. Headlamp battery saver The battery saver will shut off the exterior lamps 10 minutes after theignition switch has been turned off if the headlam...

Autolamp delay system (if equipped) If your vehicle has an autolamp delay feature, you can set the delay timeto keep the headlights on for up to three minutes after the key is turnedOFF. The delay time is set to 20 seconds at the factory, but the delaytime may be changed by following the steps below...

• the parking brake must be released. Always remember to turn on your headlamps at dusk or duringinclement weather. The Daytime Running Lamp (DRL) system does not activate the tail lamps and generally may not provideadequate lighting during these conditions. Failure to activate yourheadlamps under t...

PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel. • Push and hold top of control tobrighten. • Push and hold bottom of controlto dim. AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant.If your vehicle has been in an accident the align...

3. Turn on the low beam headlamps to illuminate the wall or screen andopen the hood. Cover the left-hand headlamp with an opaque cloth. 4. On the wall or screen you willobserve a light pattern with adistinct horizontal edge of highintensity light towards the right. Ifthis edge is not at the horizont...

The dome lamp control has threepositions: • OFF: In this position, the lampwill not illuminate. • DOOR: In this position, the domelamp will illuminate only when adoor is opened and will remainilluminated for 25 seconds after the door is shut. • ON: In this position, the lamp will remain illuminated....

Replacing headlamp bulbs 1. Make sure that the headlamp control is in the OFF position and openthe hood. 2. Press down on the wire retainerto release it and access the back ofthe headlamp assembly. Lowbeam bulb replacement 3. Locate the outboard most bulb,turn it a 1 ⁄ 4 turn to the outside of the v...

MULTI-FUNCTION LEVER Windshield wiper: For intermittent operation, move control down oneposition. Adjust the rotary control to thedesired speed setting. For normal or low speed wiperoperation, move control down twopositions from OFF. For high speed wiper operation,move control down three positionsfr...

Rear window wiper/washer controls For intermittent operation of rearwiper, rotate end of control upwardto the position. For normal speed rear wiperoperation, rotate control upward toON. To activate the rear washer, rotatethe control to the position and release. Changing the wiper blades 1. Pull the ...

To prolong the life of the wiper blades, it is highly recommended toscrape off the ice on the windshield before turning on the wipers. Thelayer of ice has many sharp edges and can damage the micro edge of thewiper rubber element. TILT STEERING WHEEL To adjust the steering wheel: 1. Pull down the ste...

Do not keep electrical devices plugged in the power pointwhenever the device is not in use. It is not recommended to useany extension cord with the 110 VAC power point, since it willdefeat the safety protection design provided by the cap and twisttab. It will also cause the power point to overload d...

One touch down Allows the driver’s window to openfully without holding the controldown. Press completely down onAUTO and release quickly. Pressagain to stop. Window lock (if equipped) The window lock feature disables allthe power windows except thedriver’s. To lock out all the window controlsexcept ...

MESSAGE CENTER With the ignition in the RUN position,the message center, located on yourinstrument cluster, displays importantvehicle and daily driving information through a constant monitor ofvehicle systems. You may select display features on the messagecenter for a display of status preceded by a...

System warnings/information System warnings alert you to possible problems or malfunctions in yourvehicle’s operating systems. In the event of a multiple warning situation, the message center willcycle the display to show all warnings by displaying each one for fourseconds. The message center will d...

• Washer fluid • Brake fluid • Engine sensor Contact your Ford dealer as soon as possible if these messages occur ona regular basis. CENTER CONSOLE Your vehicle is equipped with a variety of console features. Theseinclude: 1. Power point 2. Cupholders 3. Utility compartment 4. Ash cup (if equipped) ...

LIFTGATE To open the rear window, pull theright side of the liftgate handle. To open the liftgate, pull the leftside of the liftgate handle. • Do not open the liftgate orliftgate glass in a garage or otherenclosed area with a low ceiling.If the liftgate glass is raised andthe liftgate is also opened...

Ensure that the posts are properly latched in mounting features.The cover may cause injury in a sudden stop or accident if it is not securely installed. Do not place any objects on the cargo area shade. They mayobstruct your vision or strike occupants of vehicle in the case of a sudden stop or colli...

To remove the cross-bar assembly from the roof rack side rails: 1. Loosen the thumbwheel at bothends of the cross-bar (bothcross-bars are adjustable). 2. Slide the cross-bar to the end ofthe rail. 3. Use a long, flat object to depressthe tongue in the endcaps on bothsides of the cross-bar. 4. Slide ...

To reinstall the cross-bar assembly to the roof rack side rails: 1. Ensure that both cross-barassemblies are installed with the F(front) arrow facing towards thefront of the vehicle. 2. Use a long, flat object to depressthe tongue in the endcaps on bothsides of the cross-bar. 3. Slide the cross-bar ...

KEYS One key operates all locks and starts the vehicle. Always carry a sparekey with you in case of an emergency. If you lose your dealer supplied keys, replacement keys are availablethrough your authorized dealer. POWER DOOR LOCKS The power door lock controls arelocated on the driver and frontpasse...

Repeat the procedure to turn the feature on or off. Door key unlocking/locking Two step door unlocking 1. Turn the key in the door cylinder to unlock the driver’s door. Note: The interior lamps will illuminate if the control on the overhead lamp isin the DOOR position and the perimeter alarm system ...

Childproof door locks • When these locks are set, therear doors cannot be opened fromthe inside. • The rear doors can be openedfrom the outside when the doorsare unlocked. The childproof locks are located onrear edge of each rear door andmust be set separately for each door. Setting the lock for one...

The remote entry system allows youto lock or unlock all vehicle doorswithout a key. The remote lockingand unlocking features will operateindependent of the ignition position;however, the panic feature will onlyoperate when the ignition is in the 1(LOCK) or 2 (ACCESSORY)position. If there are problem...

2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board. 3. Remove the old battery. Note: Please refer to local regulations when disposing of transmitter batteries. 4. Insert the new battery. Refer to the diagram inside the remote entrytransmitter for the correc...

To reprogram the remote entrytransmitters: 1. Ensure the vehicle is electronically unlocked. 2. Put the key in the ignition. 3. Turn the key from the 1 (LOCK) position to 3 (RUN). 4. Cycle eight times rapidly (within 10 seconds) between the 1 (LOCK)position and 3 (RUN). Note: The eighth turn must en...

• after 25 seconds of illumination. Illuminated exit • The interior lights will illuminate when the key is removed from theignition. The lamps automatically turn off after 25 seconds. The dome and cargolamp controls must not be set to the OFF position for the illuminated exit system to operate. PERI...

Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by pressing the control on your remote entry transmitter. • Unlock the doors with a key. Turn the key full travel (toward the frontof the vehicle) to ensure the alarm disarms. • Turning the key in the ...

FRONT SEATS Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Adjustable head restraints T...

Adjusting the front manual seat Lift handle to move seat forward orbackward. Pull lever up to adjust seatback. Adjusting the front power seat (if equipped) The control is located on the outboard side of the seat cushion. Press to raise or lower the frontportion of the seat cushion. 2005 Escape Hybri...

Press to raise or lower the rearportion of the seat cushion. Press the control to move the seatforward, backward, up or down. Heated seats (if equipped) To operate the heated seats: • Push the control located on theseat to activate. • Push again to deactivate. The heated seats will activate when the...

The head restraints can be movedup and down. Lift the head restraintso that it is located directly or asclose as possible behind your head. Push control to lower or removehead restraint. Folding down rear seats 1. Raise the rear seat head restraintand remove. 2. Place the head restraint underthe fro...

3. Pull the seat release control. Note: Make sure the floor is clear of all objects before folding the seat. 4. Flip seat forward. Attach the safety belt web snapbutton to the quarter trim panelsnap button. This will ensure thatsafety belt does not get caught bystaying out of the seat back foldingpa...

To remove the rear cushion 1. Lift the yellow tab to release thehinges. 2. Pull the cushion to the outboardside of the vehicle. To install the rear cushion 1. Push the cushion to the inboardside of the vehicle. 2. Make sure that the hinges arelocked into place. SAFETY RESTRAINTS Safety System The Sa...

Driver’s seat position sensor The driver’s seat position sensor allows your Safety System to tailor thedeployment level of the driver airbag based on seat position. The systemis designed to help protect smaller drivers sitting close to the driverairbag by providing a lower airbag output level. Front...

• A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and warning light are repaired. If any of these things happen, even intermittently, have the SafetySystem serviced at your dealership or by a qualified technicianimmediately. Unless serviced, the syste...

All safety belts in the vehicle are combination lap and shoulder belts.The passenger safety belts have two types of locking modes describedbelow: Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt lengthadjustment to your movements and locking in response to ve...

Safety belt height adjustment Your vehicle has safety belt heightadjustments at the front outboardseating positions. Adjust the heightof the shoulder belt so the belt restsacross the middle of your shoulder. To adjust the shoulder belt height,squeeze and hold the buttons on theside and slide the hei...

Safety belt extension assembly If the safety belt is too short when fully extended, there is an 8 inch (20cm) safety belt extension assembly that can be added (part number611C22). This assembly can be obtained from your dealer at no cost. Use only extensions manufactured by the same supplier as the ...

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data): Reasons given... Consider... ⬙ Crashes are rare events ⬙ 36700 crashes occur every day. The more we drive, the more we areexposed to ⬙ rare ⬙ events, even for good drivers. 1 in 4 of us will b...

Reasons given... Consider... ⬙ The people I’m with don’t wear belts ⬙ Set the example, teen deaths occur 4times more often in vehicles withTWO or MORE people. Children andyounger brothers/sisters imitatebehavior they see. ⬙ I have an airbag ⬙ Airbags offer greater protection whenused with safety bel...

Safety belt maintenance Inspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to make surethere are no nicks, tears or cuts. Replace if necessary. All safety beltassemblies, including retractors, buckles, front safety belt buckleass...

Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries.Airbags DO NOT inflate slowly;there is a risk of injury from adeploying airbag. All occupants of the vehicle, including the driver, should alw...

Do not attempt to service, repair, or modify the airbagsupplemental restraint systems or its fuses. See your Ford or Lincoln Mercury dealer. Modifications to the front end of the vehicle, including frame,bumper, front end body structure, tow hooks and B-pillar surrounding parts may affect the perfor...

How does the airbag supplemental restraint system work? The airbag SRS is designed toactivate when the vehicle sustains alongitudinal deceleration sufficientto cause the airbag sensors to closean electrical circuit that initiatesairbag inflation. The fact that theairbags did not inflate in a collisi...

If it is necessary to modify an advanced front airbag system toaccommodate a person with disabilities, contact the Ford CustomerRelationship Center at the phone number shown in the CustomerAssistance section of this Owner’s Guide . Any alteration/modification to the front passenger seat mayaffect th...

How does the Safety Canopy 姟 system work? The design and development of theSafety Canopy 娂 system included recommended testing proceduresthat were developed by a group ofautomotive safety experts known asthe Side Airbag Technical WorkingGroup. These recommended testingprocedures help reduce the risk...

to inflate in side-impact collisions, not roll-over, rear-impact, frontal ornear-frontal collisions, unless the collision causes sufficient lateraldeceleration. Several air bag system components get hot after inflation. Do nottouch them after inflation. If the side airbag hasdeployed, the airbag wil...

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag supplemental restraint system (SRS) in this chapter for special instructions about using airbags. Important child restraint precautions You are required by l...

Child booster seats Children outgrow a typical convertible or toddler seat when they weigh40 lb. (18 kg) and are around 4 years of age. Although the lap/shoulderbelt will provide some protection, these children are still too small forlap/shoulder belts to fit properly, which could increase the risk ...

Types of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has aremovable shield, remove theshield and use the lap/shoulderbelt. If a seating position has alow seat back and no headrestraint, a backless booster seatmay place...

8. Allow the safety belt to retract toremove any slack in the belt. 9. Before placing the child in theseat, forcibly tilt the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the seat at the belt pathand attempt to move it side to sideand forward and back. Ther...

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare encountered on streets,highways and off-road. Utilityvehicles and trucks are not designedfor cornering at speeds as high aspassenger cars any more tha...

Power is supplied to all four wheels through a transfer case or powertransfer unit. 4WD vehicles allow you to select different drive modes asnecessary. You should become thoroughly familiar with this informationbefore you operate your vehicle. Do not become overconfident in the ability of 4WD and AW...

Every day before you drive, checkyour tires. If one looks lower thanthe others, use a tire gauge to checkpressure of all tires and adjust ifrequired. At least once a month and beforelong trips, inspect each tire andcheck the tire pressure with a tiregauge (including spare, if equipped).Inflate all t...

Always inflate your tires to the Ford recommended inflation pressureeven if it is less than the maximum inflation pressure information foundon the tire. The Ford recommended tire inflation pressure is found onthe tire label or certification label which is located on the B-Pillar or theedge of the dr...

Tire change procedure When one of the front wheels is off the ground, the transmissionalone will not prevent the vehicle from moving or slipping off the jack, even if the vehicle is in P (Park). To help prevent the vehicle from moving when you change a tire,be sure the parking brake is set, then blo...

If equipped with a tether, perform the following additional steps: 4. Lift the spare tire on end toaccess tether attachment (1). 5. Use the lug wrench to remove thelug nut from the spare tire tether. 6. If not replacing the spare or flattire to the underbody storage area,raise winch up into the inst...

Changing the flat tire 8. Loosen each wheel lug nutone-half turn counterclockwise butdo not remove them until the wheelis raised off the ground. Before placing the jack under the vehicle, NOTE the jack locations: • Front 2005 Escape Hybrid (hev) Owners Guide (post-2002-fmt)USA (fus) Tires, Wheels an...

• Rear 9. Lower the jack from its storedheight to fit under the jackingnotches. Position the jack accordingto the following guides and turn thejack handle clockwise until the tireis a maximum of 1 inch (25 mm) offthe ground. Never use the differentials as ajacking point. To lessen the risk ofpersona...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent from this example.) 1. P: Indicates a tire, designated by the Tir...

Note: You may not find this information on all tires because it is not required by federal law. Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R 106 mph (171 km/h) S 112 mph (180 km/h) T 118 mph (190 km/h) U 124 mph (200 km/h) H 130 mph (210 km/h)...

11. Maximum Load: Indicates the maximum load in kilograms and pounds that can be carried by the tire. Refer to the tire label or thesafety certification label, which is located on the B-Pillar or the edge ofthe driver’s door, for the correct tire pressure for your vehicle. 12. Treadwear, Traction an...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon ...

Information on “T” type tires “T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below: T145/80D16 is an example of a tiresize. Note: The temporary tire size for your vehicle may be different fromthis example. 1. T: Indicates a type of tire, ...

Safety practices Driving habits have a great deal to do with your tire mileage and safety. • Observe posted speed limits • Avoid fast starts, stops and turns • Avoid potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking If your vehicle is stuck in snow,...

The tires should also be balanced periodically. An unbalanced tire andwheel assembly may result in irregular tire wear. Tire rotation Rotating your tires at the recommended interval (as indicated in the scheduled maintenance information that comes with your vehicle) will help your tires wear more ev...

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive(4WD)/ All Wheel Drive (AWD)vehicles (front tires at top ofdiagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask a qualified technician at a Ford or Lincoln Mercury dealership to check ...

Payload – is the combined weight of cargo and passengers that the vehicle is carrying. The maximum payload for your vehicle can be foundon the Tire Label on the B-Pillar or the edge of the driver’s door. Lookfor “THE COMBINED WEIGHT OF OCCUPANTS AND CARGO SHOULD NEVER EXCEED XXX kg OR XXX lb.” for m...

Example only: Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. 2005 Escape Hybrid (hev) Owners Guide (post-2002-fmt)USA (fus) Tires, Wheels and Loading 193

GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance...

GVWR (Gross Vehicle WeightRating) – is the maximum allowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo). The GVWR is shown on theSafety Compliance CertificationLabel located on the B-Pillar orthe edge of the driver’s door.The GVW must never exceed theGV...

• Use extra caution when driving while trailer towing. Refer to Driving while you tow in this chapter. • Service your vehicle more frequently if you tow a trailer. Refer to thesevere duty schedule in the scheduled maintenance guide. • Do not tow a trailer until your vehicle has been driven at least ...

4WD GCWR (Gross Combined Weight Rating)/Trailer Weights Engine Maximum GCWR - lb. (kg) Trailer Weight Range - lb. (kg) 2.3L 4980 (2259) 1000 (454) Notes: For high altitude operation, reduce GCW by 2% per 1000 ft. (300 meters) elevation. For definitions of terms and instructions oncalculating your ve...

If you use a rental trailer, follow the instructions that the rental agencygives to you. Do not attach safety chains to the bumper. Trailer brakes Electric, manual, automatic or surge-type brakes, if compatible with thevehicle, are safe if installed properly and adjusted to the manufacturer’sspecifi...

• Allow more distance for stopping with a trailer attached. • If you are driving down a long or steep hill, shift to a lower gear. Donot apply the brakes continuously, as they may overheat and becomeless effective. • The trailer tongue weight should be 10–15% of the loaded trailer weight. • After yo...

5. Turn the key to 3 (RUN) withoutturning the key to 4 (START). Make sure the corresponding lights on the instrument panel clusterilluminate or illuminate briefly. If a light fails to illuminate, have thevehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate. Start...

Turn the key to 4 (START), thenrelease the key as soon as thevehicle starts. After the vehicle hasbeen started, a vehicle outlined andilluminated in green (also called the Ready Indicator Light) will light inthe instrument cluster to indicate the vehicle is on. This indicator willremain illuminated ...

If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important ventilating information If the engine is idling while the vehicle is stopped for a long period oftime, open the windows at least one inch (2.5 cm) or a...

AUTOMATIC TRANSMISSION OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever from being moved from P (Park) when the ignition isin the RUN position unless brake pedal is depressed.If you cannot move the gearshift lever out of P...

R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward.Always come to a complete stop before shifting into and out of R(Reverse). N (Neutral) With the gearshift lever in N (Neutral), the vehicle is free to roll; holdthe brake pedal down while in this position. Because of...

You should either know the terrain or examine maps of the area beforedriving. Map out your route before driving in the area. To maintainsteering and braking control of your vehicle, you must have all fourwheels on the ground and they must be rolling, not sliding or spinning. Basic operating principl...

• If the vehicle goes from one type of surface to another (i.e., fromconcrete to gravel) there will be a change in the way the vehicleresponds to a maneuver (steering, acceleration or braking). Again,avoid these abrupt inputs. Sand When driving over sand, try to keep all four wheels on the most soli...

“Tread Lightly” is an educationalprogram designed to increase publicawareness of land-use regulationsand responsibilities in our nation’swilderness areas. Ford MotorCompany joins the U.S. Forest Service and the Bureau of LandManagement in encouraging you to help preserve our national forest andother...

GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the New Vehicle Limited...

Using roadside assistance Complete the roadside assistance identification card and place it in yourwallet for quick reference. In the United States, this card is found in theOwner Guide portfolio in the glove compartment. In Canada, the card isfound in the Owner Information Guide in the glove compar...

To reset the switch(es): 1. Turn the ignition to LOCK. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset the switch by pushing in on the resetbutton. Both switches should be checked and reset. 4. Turn the ignition to RUN. 5. Wait a few seconds and return the key to LOCK. 6. Make...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

Power distribution box The power distribution box is located in the engine compartment. Thepower distribution box contains high-current fuses that protect yourvehicle’s main electrical systems from overloads. Always disconnect the low voltage (underhood) battery beforeservicing high current fuses. T...

Auxiliary relay box The relay box is located on the radiator support (left of the hood latch). Fuse/Relay Location Description Relay 1 Driver side cooling fan Relay 2 Passenger side cooling fan (low-speed) Relay 3 Passenger side cooling fan (high-speed) JUMP STARTING YOUR VEHICLE (LOW VOLTAGE [UNDER...

Batteries contain sulfuric acid which can burn skin, eyes andclothing, if contacted. Do not attempt to push-start your vehicle. This vehicle does nothave push-start capability. Preparing your vehicle If your low voltage (underhood) battery becomes disconnected ordisabled for any reason, the vehicle ...

Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+)termi...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In ...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

When the button is pressed, the indicator light on the button willilluminate. After eight minutes has passed, the indicator light will flashrapidly for two minutes. Turn the ignition to RUN. You may now attemptto start the engine. If you attempt to start the engine before the eight minutes passes, t...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handling your vehicle linewill provide warranty service, we recommend you return to your sellingdealer who wants to ensure your continued satisfaction. Pl...

In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action under the Magnuson-MossWarranty Act, or to the extent allowed by state law, before pursuingreplacement or repurchase remedies provided by certain state laws. Thisdispute handling procedure ...

• available free to owners and lessees of qualifying Ford Motor Companyvehicles. The Dispute Settlement Board may not be available in all states. FordMotor Company reserves the right to change eligibility limitations, modifyprocedures and/or to discontinue this service without notice and withoutincu...

before the Board, this is not a requirement and the Board will decide thecase whether or not an oral presentation is made. An oral presentationmay be requested by the Board as well. Making a decision Board members review all available information related to eachcomplaint, including oral presentation...

The CAMVAP program is a straight-forward and relatively speedyalternative to resolve a disagreement when all other efforts to produce asettlement have failed. This procedure is without cost to you and isdesigned to eliminate the need for lengthy and expensive legalproceedings. In the CAMVAP program,...

Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website:www.helminc.com. (Items in this catalog may be purchased by credit card, check ormoney order.) Obtaining a French owner’s guide French Owner’s Guides can be obtained from your dealer or by writing toFord ...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft Detail Wash (ZC-3–A), which isavailable from your dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can discolor and s...

• Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, such as grained door handles, roofracks, bumpers, side moldings, mirror housings or the windshield cowlarea. The paint sealant will “gray” or stain the parts over time. PAINT CHIPS Your dealer has touch-...

• Spray Motorcraft Engine Shampoo and Degreaser (ZC-20) on all partsthat require cleaning and pressure rinse clean. • Cover the highlighted areas to prevent water damage when cleaningthe engine. Note: As with all transmissions, be especially careful as water entry into the vents can damage internal ...

• Do not use fuel, kerosene, or paint thinner to clean any parts. • Wiper blades can be cleaned with isopropyl (rubbing) alcohol orwindshield washer solution. Be sure to replace wiper blades when theyappear worn or do not function properly. Do not use sharp objects, such as a razor blade, to clean t...

• Do not use household cleaning products or glass cleaners, which canstain and discolor the fabric and affect the flame retardant abilities ofthe seat materials. Do not use cleaning solvents, bleach or dye on the vehicle’ssafety belts, as these actions may weaken the belt webbing. Do not use chemica...

FORD AND LINCOLN MERCURY CAR CARE PRODUCTS Your Ford or Lincoln Mercury dealer has many quality products availableto clean your vehicle and protect its finishes. These quality productshave been specifically engineered to fulfill your automotive needs; theyare custom designed to complement the style ...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide scheduled maintenance information which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provi...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel. 2. At the front of the vehicle, lift up on the auxiliary latch handle locatedin the center between the hood and the grille. 3. Lift the hood open and secure it with the prop rod. 2005...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Engine coolant reservoir 2. Motor/Electronics (M/E) coolant reservoir 3. Engine oil filler cap 4. Brake fluid reservoir 5. Power distribution box 6. Low Voltage (underhood) battery 7. Engine air filter assembly 8. Engine oil dipstick...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meets Ford specifications. Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic compounds m...

3. Set the parking brake and ensure the gearshift is securely latched in P(Park). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil ...

Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler capand use a funnel to pour the engine oil...

Note: Electrical or electronic accessories or components added tothe vehicle by the dealer or the owner (e.g. spot lights, electricwinch, etc.) may adversely affect vehicle performance anddurability. Batteries normally produce explosive gases which can causepersonal injury. Therefore, do not allow f...

4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine to idle for at least one minute. 6. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven 10 miles (16 km) or more torelearn the idle and fuel trim strategy. • If you do n...

ENGINE COOLANT AND MOTOR/ELECTRONICS COOLANT Your vehicle is equipped with two separate coolant systems. One is forengine cooling and the other is for various electric motors and othercomponents that are specific to the Escape Hybrid operating systems. Checking engine coolant The concentration and l...

Checking motor/electronics (M/E) coolant The M/E coolant reservoir is locatedbehind the engine coolant reservoir.Refer to the following enginecoolant sections for all information,instructions and warnings related tocooling systems. The two systemsuse the same coolant and operatesimilarly, with the M...

If the engine coolant has not been checked at the recommended interval,the engine coolant reservoir may become low or empty. If the reservoir islow or empty, add engine coolant to the reservoir. Refer to Adding engine coolant in this chapter. Note: Automotive fluids are not interchangeable; do not u...

• Do not use alcohol, methanol, brine or any engine coolantsmixed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating orfreezing. • Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosion...

Whenever coolant has been added, the coolant level in the coolantreservoir should be checked the next few times you drive the vehicle. Ifnecessary, add enough 50/50 concentration of engine coolant anddistilled water to bring the liquid level to the proper level. If you have to add more than 1.0 quar...

If you drive in extremely hot climates: • It is still necessary to maintain the coolant concentrationabove 40%. • NEVER decrease the coolant concentration below 40%. • Decreased engine coolant concentrations below 40% willdecrease the corrosion protection characteristics of the enginecoolant and may...

Refueling Fuel vapor burns violently and a fuel fire can cause severeinjuries. To help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • Turn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep spa...

Do not be concerned if your engine sometimes knocks lightly. However, ifit knocks heavily under most driving conditions while you are using fuelwith the recommended octane rating, see your dealer or a qualifiedservice technician to prevent any engine damage. Fuel quality If you are experiencing star...

Replace the fuel filter with an authorized Motorcraft part. Thecustomer warranty may be void for any damage to the fuel systemif an authorized Motorcraft fuel filter is not used. ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, th...

5. Follow one of the simple calculations in order to determine fueleconomy: Calculation 1: Divide total miles traveled by total gallons used. Calculation 2: Multiply liters used by 100, then divide by total kilometers traveled. Keep a record for at least one month and record the type of driving (cit...

• Use recommended engine oil. Refer to Lubricant specifications in this chapter. • Perform all regularly scheduled maintenance items. Follow therecommended maintenance schedule and owner maintenance checksfound in scheduled maintenance information. Conditions • Heavily loading a vehicle or towing a ...

Note: The brake system on the Escape Hybrid can only be bled at a qualified Ford dealer. TRANSMISSION FLUID Checking electronically controlled continuously variabletransmission (eCVT) Refer to your scheduled maintenance information chapter for scheduled intervals for fluid checks and changes. Your t...

7. The fluid level should be within1/4 inch (6 mm) of the plug threads. 8. Replace the check plug. Adjusting eCVT fluid levels Before adding any fluid, make sure the correct type is used. The type offluid used is indicated in the Lubricant specifications section in this chapter. Use of a non-approve...

Air filter 1. Release the clamps that secure the air filter housing cover. 2. Carefully separate the two halvesof the air filter housing. 3. Remove the air filter element from the air filter housing. 4. Wipe the air filter housing and cover clean to remove any dirt ordebris and to ensure good sealin...

Changing the high voltage battery air filter element 1. Remove access panel located inthe rear cargo area on the driver’sside trim panel to expose the filtercover. 2. Push the tabs (located on eachside of filter cover) while pullinggently to remove filter cover. 3. Install new filter and filter cove...

Fluid Ford PartName Application Capacity Rear axlelubricant Motorcraft SAE80W-90Premium RearAxle Lubricant 4WD 2.96 pints(1.4L) 4 Windshieldwasher fluid MotorcraftPremiumWindshieldWasherConcentrate All 2.7 quarts(2.6L) 1 Using any transmission fluid other than those that meet the recommended specifi...

LUBRICANT SPECIFICATIONS Item Ford PartName orequivalent Ford PartNumber FordSpecification Body hinges, latches,door striker platesand rollers, seattracks, fuel filler doorhinge and spring,primary and auxiliaryhood latches Multi-PurposeGrease XG-4 or XL-5 ESB-M1C93-B Brake fluid Motorcraft HighPerfo...

Item Ford PartName orequivalent Ford PartNumber FordSpecification PowerTake-off(PTO) 3 (4WD) Motorcraft SAE75W-140 HighPerformanceRear AxleLubricant XY-75W140–QL WSL-M2C192-A Windshield washerfluid MotorcraftPremiumWindshieldWasherConcentrate ZC-32–A WSB-M8B16–A2 1 DO NOT USE Motorcraft Specialty Or...

Vehicle identification number (VIN) The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Please note thatin the graphic XXXX isrepresentative of your vehicleidentification number.) The vehicle identification number (VIN) contains the followin...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford or Ford of Canada dealer.These quality accessories have been specifically engineered to fulfill yourautomotive needs; they are custom designed to co...

GENERAL MAINTENANCE INFORMATION Why maintain your vehicle? This guide describes the scheduled maintenance required for yourvehicle. Carefully following this schedule helps protect against majorrepair expenses resulting from neglect or inadequate maintenance andmay also help to increase the value of ...

Any modification of the emissions control system could create liabilityunder federal law (U.S.) if made prior to sale and registration, under thelaws of some states if made thereafter. Further, federal law prohibitsvehicle manufacturers, dealers and other persons engaged in thebusiness of repairing,...

WHICH MAINTENANCE SCHEDULE SHOULD YOU FOLLOW? Owner Checks and Services Refer to Mileage Intervals for Additional Checks and Services Certain basic maintenance checks and inspections should be performedby the owner or a service technician at the intervals indicated. Serviceinformation and supporting...

U.S. SCHEDULE Maintenance Item Maintenance Interval Miles (x 1000) 5 1 0 2 0 3 0 4 0 5 0 6 0 7 0 Km (x 1000) 8 1 6 3 2 4 8 6 4 8 0 9 6 112 Change engine oil and replace oil filter ••••••• Inspect tires for wear and measure tread depth • • •••••• Rotate tires • • •••••• Inspect brake pads, shoes, rot...

Date: Odometer reading: R.O.# Dealer’s Stamp: Date: Odometer reading: R.O.# Dealer’s Stamp: CANADIAN SCHEDULE For items marked with an asterisk (*), more frequent service intervalswill be required. Refer to Special operating conditions at the end of this section for more information. 2005 Escape Hyb...

Date: Odometer reading: R.O.# Dealer’s Stamp: See corresponding mileage in maintenance schedule for services performed. Date: Odometer reading: R.O.# Dealer’s Stamp: See corresponding mileage in maintenance schedule for services performed. Date: Odometer reading: R.O.# Dealer’s Stamp: See correspond...

A Accessory delay ..........................91 Air cleaner filter ...............284–286 Airbag supplemental restraintsystem ................139–140, 146, 150 and child safety seats ............141description ..............140, 146, 150disposal ....................................152driver airbag .....

Towing .......................................198 recreational towing .................202trailer towing ..........................198wrecker ....................................239 Transmission .............................211 brake-shift interlock (BSI) ....211fluid, checking and adding(automatic)...