Ford 2004 Focus v.1- Manuals

for Emissions Defect and Emissions Performance Warranties. For adetailed description of what is covered and what is not covered, refer tothe Warranty Guide that is provided to you along with your Owner’s Guide. Special instructions For your added safety, your vehicle is fitted with sophisticated ele...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -No...

WARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster 2.3L 14 PZEV instrument cluster Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of y...

Many lights will illuminate when you start your vehicle to make sure thebulb works. If any light remains on after starting the vehicle, have therespective system inspected immediately. Check engine: The Check Engine indicator light illuminates when theignition is first turned to the ONposition to ch...

Driving a vehicle with the brake system warning light on isdangerous. A significant decrease in braking performance may occur. It will take you longer to stop the vehicle. Have the vehiclechecked by your dealer immediately. Anti-lock brake system: If the ABS light stays illuminated orcontinues to fl...

Overdrive off (if equipped): Illuminates when the overdrivefunction of the transaxle has beenturned off, refer to the Driving chapter. If the light flashes steadily or does not illuminate, have thetransmission serviced soon, or damage may occur. Upshift (if equipped): To maximize fuel economy, this ...

AM/FM STEREO WITH CASSETTE (IF EQUIPPED) 1. Cassette door: Insert the cassette with the opening to the right. 2. Rewind/fast forward : Press to reverse/advance to the previous/nextcassette selection. If the end of thetape is reached, playback begins on the other side. Partially press both tochange t...

5. Menu: Press MENU to access main menu functions. UseSEEK / for adjustments. Tune adjust: Press MENU until MAN appears in the display. Press or to manually move down/up the radio frequency band. Dolby: Dolby 威 noise reduction reduces the amount of hiss and static during tape playback Press MENU unt...

Press the security release control and remove the front panel. Toreposition the panel, insert the right-hand edge first, then the left-handside, until the retaining latch is engaged. Replacement panels: Your Ford Dealer will require the following if you need to order a replacement panel: • Your name...

9006 AM/FM SOUND SYSTEM WITH 6–DISC IN DASH CHANGER(IF EQUIPPED) 1. CD Door: Insert the disc with the playing side down and printedside up. 2. Load: Press to load a CD. WAIT will appear in the display thenchange to INSERT. Insert the CD.LOAD and a disc icon will flash in the display. Repeat this ste...

CD eject during playback: Press the eject control during CD playback to eject the CD. Press again to cancel the eject process. To eject anotherdisc, press the preset control that corresponds to the desired disc thenpress EJ. EJECT CD will appear in the display. REMOVE will appear asthe disc is held ...

broadcasting a particular program type. Select AUDIO and press ENTER.Select PTY to view the broadcast information or PTY SEARCH to searchfor stations broadcasting a particular program type. There are 30different possible program types, some being: News, Inform, Sports, Talk,Rock, Country, Jazz, etc....

system will return to the current playing media. Select AUDIO and pressENTER. Select TRAF ANNOU and press ENTER. Turn the rotary controlto turn on/off. Press BACK to save the setting. Traffic announcements not available in most U.S. markets. Loudness: This function boosts the bass frequencies. Selec...

soft key next to the desired frequency. CD/MP3: Press to select the previous/next track of the current CD/MP3. 16. Fade: Press FADE and turn the right control knob (ENTER) to shiftsound to the rear/front speakers.The display will indicate the level selected. 17. Balance: Press BAL then turn the righ...

• A maximum of 20 directories is recommended as additional directorieswill increase the access time. • Each directory can contain a maximum of 254 tracks andsub-directories. • Avoid special characters when naming directories and files. • MAIN will appear in the display when files are not stored indi...

Don’t: • Expose tapes to direct sunlight, extreme humidity, heat or cold. • Leave tapes in the cassette player for a long time when not beingplayed. CD/CD PLAYER CARE Do: • Handle discs by their edges only. Never touch the playing surface. • Inspect discs before playing. Clean only with an approved ...

HEATER ONLY SYSTEM(IF EQUIPPED) 1. Air flow selections: Controls the direction of the airflow in thevehicle. See the following for a briefdescription on each control. : Distributes outside air through the instrument panel vents. : Distributes outside air through the instrument panel vents and theflo...

To aid in side window defogging/demisting in cold weather: 1. Select 2. Set the temperature control to full heat 3. Set the fan speed to HI 4. Direct the outer instrument panel vents towards the side windows To increase airflow to the outer instrument panel vents, close the ventslocated in the middl...

REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice andfog. • A small LED will illuminate when the rear defroster is activated. The ignition must be in the ON position to operate the rear windowdef...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps,license plate lamps and tail lamps. Turns the headlamps on. Foglamp control (if equipped) The headlamp control also operatesthe foglamps. The foglamps can beturned on when the headlampcontrol is in the position ...

High beams Push the lever toward theinstrument panel to activate. Pullthe lever towards you to deactivate. Flash to pass Pull toward you slightly to activateand release to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of theinstrument panel during headlightand parklamp operation. • R...

VOR 1. Park the vehicle on a level surface approximately 7.6 meters (25 feet)from the vertical wall or the screen directly in front of it. 2. Measure the height of the headlamp bulb center from the ground andmark a 2.5 meters (8 foot) horizontal reference line on the vertical wallor screen at this h...

5. Remove the headlamp bulb cover by releasing the four snap hooks(two top and two bottom). Note: On the left headlamp, pull the bulb cover approximately 1 inch rearward and then slide it out until the vertical aiming adjuster isaccessible. 6. Turn on the low beam to illuminate the wall or screen. O...

INTERIOR LAMPS Dome lamps The dome lamp is equipped with acontrol switch that will illuminatewhen: • the doors are closed and theswitch is in the on position. • the switch is in the door activatedposition and any door is open. When the dome lamp switch is in the off position, it will not illuminatew...

Function Trade number Headlamps (VOR) HB2 Headlamps (high beam, VOL) H7 Headlamps (low beam, VOL) D2S Park lamp (front, VOL) W5W Turn lamp (front, VOL) 3457K Park and turn lamp (front) 3157K Side marker lamp (front) GE194 Foglamps (if equipped) 899 Stop/turn and tail lamps 3157K Backup lamp (sedan/w...

Replacing headlamp bulbs Make sure the headlamp switch is in the OFF position. To remove the high or low beam headlamp bulb: 1. Lift the hood and remove thebulb cover. 2. Swivel the wire clip to the sideand pull out the lamp. 3. Pull the bulb holder straight outfrom the lamp assembly. 4. Pull the bu...

Replacing high-mount brake lamp bulbs Sedan 1. Make sure the headlamp controlis in the OFF position and open theluggage compartment. 2. Using a screw driver remove thetrim from the tailgate. 3. Pull the bulb holder from thelamp assembly. 4. Pull the bulb straight out. Install in reverse order. Coupe...

MULTI-FUNCTION LEVER Windshield wiper: Move the lever down for a single wipe. For intermittent operation, movecontrol up one position and adjustthe rotary control to the desiredspeed. For normal operation, move controlup two positions. For high speed operation, move control up three positions. Mist ...

Changing the wiper blades 1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to release the bladeand pull the wiper blade downtoward the windshield to remove itfrom the arm. 2. Attach the new wiper to thewiper arm and press it into pla...

HORN Press the steering wheel pad. Thehorn can be operated when theignition is off. AUXILIARY POWER POINT Power point outlets are designedfor accessory use only. Do nothang any type of accessories oraccessory bracket from the theirplugs. Improper use of thepower point outlet can causedamage not cove...

Press and hold the bottom part ofthe rocker switch to open thewindow. Press and hold the top partof the rocker switch to close thewindow. One touch down: Allows the driver’s window to open fullywithout holding the control down.Press the driver window control completely down then release. Pressagain ...

Heated mirrors (if equipped) Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated. Do not remove ice from themirrors with a scraper orattempt to readjust the mirrorglass if it is frozen in place.These actions could causedamage to the glass and mirr...

Turning off speed control Press the speed control OFFcontrol. Note: When you turn off the speed control or the ignition, your speedcontrol set speed memory is erased. MOON ROOF (SUNROOF) (IF EQUIPPED) You can move the glass panel of the moon roof back to open or tilt up toventilate the vehicle. To o...

Relearning function: In case the moon roof does not close properly anymore, follow this relearning procedure. • Tilt the moon roof into the vent position as far as possible. Release theswitch. • Press and hold the same switch again for 30 seconds until you see themoon roof move. • Release the switch...

Wagon Pull out the roller cover and securethe retaining points. The cover canbe removed completely by pressinginward on both ends of the support. To reduce the risk of injury,the luggage cover must be properly attached to the mountingclips. Do not place any objects on the cargo area cover. They mayo...

KEYS The key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer. You should always carry a second key with you in a safe place in caseyou require it in an emergency. POWER DOOR LOCKS The power door lock controls arelocated on the driver and frontpasse...

2. Press the power door unlock control three times. 3. Turn the ignition key from ON to OFF. 4. Press the power door unlock control three times. 5. Turn the ignition back to ON. The horn will chirp. 6. Press the unlock control, then press the lock control. The horn willchirp once if autolock was dea...

REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RS-210 ofIndustry Canada. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) This devicemust accept any interference received, including interfe...

Unlocking the doors 1. Press and release to unlock the driver’s door. Note: The interior lamps will illuminate. 2. With the all-door remote entry, press and release again within three seconds to unlock all the doors. The remote entry system activates the illuminated entry feature. Thisfeature turns ...

To replace the battery: 1. Twist a thin coin between the twohalves of the remote entrytransmitter near the key ring. DONOT TAKE THE RUBBER COVERAND CIRCUIT BOARD OFF THEFRONT HOUSING OF THEREMOTE ENTRY TRANSMITTER. 2. Do not wipe off any grease on thebattery terminals on the backsurface of the circu...

To reprogram the remote entrytransmitters: 1. Close all doors and fasten the driver’s seat belt to ensure conflictingchimes do not sound during the procedure. 2. Put the key in the ignition. 3. Turn the key from the 1 (OFF) position to 3 (ON). 4. Cycle four times rapidly (within 10 seconds) between ...

key chain may cause vehicle starting issues. You need to prevent theseobjects from touching the coded key while starting the engine. Theseobjects will not cause damage to the coded key, but may cause amomentary issue if they are too close to the key when starting theengine. If a problem occurs, turn...

PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will warn you in the event of anunauthorized entry to your vehicle. If there is any potential perimeter anti-theft problem with your vehicle,ensure ALL remote entry transmitters are taken to the dealership to aid in troubleshooting...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Adjustable head restraints (if e...

Adjusting the front manual seat Pull the lever located under thefront edge of the seat to move theseat forward or backward. Turn the control to adjust thelumbar support. Turn the handle to adjust the heightof the seat. Lift the control to adjust the angleof the seatback. 2004 Focus (foc) Owners Guid...

Heated seats (if equipped) The heated seats switch is located on the center console. To operate the heated seats: • Push control to activate. • Push again to deactivate. The maximum temperature is reached after five or six minutes. The indicator light on the switch is illuminated when activated. The...

On three door models, front safetybelts should be pulled backwards toallow easier entry to or exit fromthe rear seats. Do not place objects behind the seat which could prevent theengagement of the seat lock. REAR SEATS Folding rear seat cushion forward Lift the seat cushion and pull itforward. When ...

Folding the rear seat back forward Coupe and wagon Remove the head restraints (ifequipped) of the rear seats andstow them on the floor behind thefront seats. Push the unlocking control on therear seatback and fold the rearseatback forward. Sedan Remove the head restraints (ifequipped) of the rear se...

Folding the seat cushion and seatback forward Pull the loop between the respectiveseat cushion and seatback, and foldthe seat cushion on that sideforward. Remove the head restraint(s) (ifequipped) of the rear seat, and foldthe seatback forward. Stow the head restraint(s) in theplastic retainers prov...

Safety belt precautions Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. To reduce the risk of injury, make sure children sit where theycan be properly restrained. Never let a passenger hold a child on his or her lap while thevehicle is moving. The passe...

BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED ifthe seat belt assembly “automatic locking retractor” feature or any other seat belt function is not operating properly when checkedaccording to the procedures in Workshop Manual. Failure to replace the belt and retractor assembly could increasethe risk ...

Safety belt pretensioner Your vehicle is equipped with safety belt pretensioners at the driver andfront outboard passenger seating positions. The safety belt pretensioner is a device which removes excess webbingfrom the safety belt system. The safety belt pretensioner uses the samecrash sensor syste...

One time disable Any time the safety belt is buckled and then unbuckled during anignition ON cycle, the BeltMinder will be disabled for that ignition cycleonly. Deactivating/activating the BeltMinder feature Read steps 1 - 9 thoroughly before proceeding with thedeactivation/activation programming pr...

5. Buckle then unbuckle the safety belt three times, ending with thesafety belt unbuckled. • After step 5 the safety belt warning light will be turned on for threeseconds. 6. Within seven seconds of the safety belt warning light turning off,buckle then unbuckle the safety belt. • This will disable B...

equipped), child safety seat LATCH and tether anchors, and attachinghardware, should be inspected after a collision. Ford Motor Companyrecommends that all safety belt assemblies in use in vehicles involved ina collision be replaced. However, if the collision was minor and aqualified technician finds...

Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries. Airbags DO NOT inflate slowly; there isa risk of injury from a deploying airbag. All occupants of the vehicle, including the driver, should a...

Do not attempt to service, repair, or modify the air bagsupplemental restraint systems or its fuses. See your Ford or Lincoln Mercury dealer. Children and air bags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseatin...

The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion ...

• diagnostic module. • and the electrical wiring which connects the components. The diagnostic module monitors its own internal circuits and thesupplemental air bag electrical system wiring (including the impactsensors), the system wiring, the air bag system readiness light, the airbag back up power...

The fact that the air bags did not inflate in a collision does not mean thatsomething is wrong with the system. Rather, it means the forces werenot of the type sufficient to cause activation. Side air bags are designedto inflate in side-impact collisions, not roll-over, rear-impact, frontal ornear-f...

Do not leave children, unreliable adults, or pets unattended inyour vehicle. Safety belts and seats can become hot in a vehicle that has beenclosed up in sunny weather, they could burn a small child. Check seat covers and buckles before you place a child anywhere near them. Important child restraint...

Do not leave children, unreliable adults, or pets unattended inyour vehicle. Child booster seats Children outgrow a typical convertible or toddler seat when they weigh40 pounds and are around 4 years of age. Although the lap/shoulder beltwill provide some protection, these children are still too sma...

Types of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has aremovable shield, remove theshield and use the lap/shoulderbelt. If a seating position has alow seat back and no headrestraint, a backless booster seatmay place...

• LATCH lower anchors are recommended for use by children up to22 kg (48 pounds) in a child restraint. Top tether anchors can be usedfor children up to 27 kg (60 pounds) in a child restraint, and toprovide upper torso restraint for children up to 36 kg (80 pounds)using an upper torso harness and a b...

8. Allow the safety belt to retract toremove any slack in the belt. 9. Before placing the child in theseat, forcibly move the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the seat at the belt pathand attempt to move it side to sideand forward. There should ...

STARTING Positions of the ignition 1. LOCK, locks the steering wheel,automatic transaxle gearshift leverand allows key removal. 2. OFF, shuts the engine and allelectrical accessories off withoutlocking the steering wheel. Theaudio system will still function. 3. ON/RUN, all electrical circuitsoperati...

Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate. Starting the engine 1. Turn the key to 3 (ON/RUN)without turning the key to 4(START). 2. Turn the ke...

Guarding against exhaust fumes Carbon monoxide is present in exhaust fumes. Take precautions to avoidits dangerous effects. If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important ventilating information If ...

effectiveness of the ABS and will increase your vehicle’s stoppingdistance. The ABS will be activated immediately, allowing you to retainfull steering control during hard braking and on slippery surfaces.However, the ABS does not decrease stopping distance. ABS warning lamp The ABS lamp in the instr...

• To return to D (Overdrive), move the gearshift lever into the D(Overdrive) position. • Selecting 2 (Second) at higher speeds will cause the transaxle todownshift to second gear at the appropriate vehicle speed. 1 (First) • Provides maximum engine braking. • Allows upshifts by moving gearshift leve...

3. Start the engine, then press the brake pedal and release the parkingbrake. 4. Move the gearshift lever to the desired gear, then slowly release theclutch pedal while slowly pressing on the accelerator. Do not drive with your foot resting on the clutch pedal or use the clutchpedal to hold your veh...

3. Turn the ignition off. Do not park your vehicle in Neutral, it may move unexpectedlyand injure someone. Use 1 (First) gear and set the parking brake fully. Removing the key Turn the ignition to position 1 (LOCK) and remove the key. DRIVING THROUGH WATER If driving through deep or standing water i...

Cargo Weight – includes all weight added to the Base Curb Weight, including cargo and optional equipment. When towing, trailer tongue loador king pin weight is also part of cargo weight. GAW (Gross Axle Weight) – is the total weight placed on each axle (front and rear) – including vehicle curb weigh...

GVWR (Gross Vehicle WeightRating) – is the maximum allowable weight of the fully loadedvehicle (including all options,equipment, passengers and cargo). The GVWR is shown on theSafety Compliance CertificationLabel located on the driver’sdoor or door pillar. The GVWmust never exceed the GVWR. Exceedin...

10–15% (conventional trailer) or king pin weight of 15–25% (fifth wheeltrailer), and driver only (68 kg [150 lbs]). Consult your dealership (or the RV and Trailer Towing Guide provided by your dealership) formore detailed information. Tongue Load or Fifth Wheel King Pin Weight – refers to the amount...

Preparing to tow Use the proper equipment for towing a trailer and make sure it isproperly attached to your vehicle. See your dealer or a reliable trailerdealer if you require assistance. Hitches Do not use hitches that clamp onto the vehicle bumper. Use a loadcarrying hitch. You must distribute the...

• Consult your local motor vehicle speed regulations for towing a trailer. • To eliminate excessive shifting, use a lower gear. This will also assistin transaxle cooling. • Anticipate stops and brake gradually. • Do not exceed the GCWR rating or transaxle damage may occur. Servicing after towing If ...

In case of a roadside emergency with a disabled vehicle (without accessto wheel dollies, car hauling trailer or flatbed transport vehicle) yourvehicle can be flat towed (all wheels on the ground) under the followingconditions: • Place the transmission in N (Neutral). • Maximum speed is 56 km/h (35 m...

GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the New Vehicle Limited...

Canadian customers who require roadside assistance, call1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford MotorCompany will reimburse a reasonable amount. To obtain reimbursementinformation, U.S. Ford or Mercury vehicles customers call1-800-241-3673; Lincoln vehicle custo...

This switch is located in the frontpassenger’s footwell, behind the kickpanel access cover. To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset theswitch by pushing in on the resetbutton. 4. Turn the ignition ON. 5. Wait a few seconds...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 61 7.5A PATS modules, Instrument cluster 62 7.5A License plate lamp 63 20A Power locks (GEM) Fuse 63 is located on the back of the fuse panel. See your dealer or acertified technician for service of this fuse. Power dis...

To remove a fuse, use the fuse puller tool provided on the powerdistribution box cover. The high-current fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 40A Main power supply to electricalsystem 2 30A Engine cooling fan (A/C) 2nd fuse 3 30A Coolin...

The use of tire sealants may damage your tires. Temporary spare tire information The temporary spare tire for your vehicle is labeled as such. It is smallerthan a regular tire and is designed for emergency use only. Replace thetemporary spare tire with a full-size tire as soon as possible. If you us...

Tire change procedure 1. Park on a level surface, activatehazard flashers and set the parkingbrake. When one of the front wheels is off the ground, the transaxlealone will not prevent the vehicle from moving or slipping off the jack, even if the vehicle is in P (Park) (automatic transaxle) or R(Reve...

6. The vehicle jacking points aredepicted on the yellow warning labelon the jack shown here. Dependingon which tire is to be changed,locate the jack at the half-mooncutout located approximately 15 cm(6 inches) from the front wheelopening (1) or approximately 38 cm(15 inches) from the rear wheelopeni...

Do not attempt to push-start your vehicle. Automatictransmissions do not have push-start capability; doing so maydamage the catalytic converter. Preparing your vehicle When the battery is disconnected or a new battery is installed, thetransmission must relearn its shift strategy. As a result, the tr...

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second ...

5. Ensure that the cables are clear of fan blades, belts, moving parts ofboth engines, or any fuel delivery system parts. Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicl...

4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the engine computer can relearn its idle conditions. + – + – 2004 Focus (foc) Owners Guide (po...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handling your vehicle linewill provide warranty service, we recommend you return to your sellingdealer who wants to ensure your continued satisfaction. Pl...

In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action under the Magnuson-MossWarranty Act, or to the extent allowed by state law, before pursuingreplacement or repurchase remedies provided by certain state laws. Thisdispute handling procedure ...

Making a decision Board members review all available information related to eachcomplaint, including oral presentations, and arrive at a fair and impartialdecision. Board review may be terminated at any time by either party. Every effort is made to decide the case within 40 days of the date thatall ...

In the CAMVAP program, impartial third-party arbitrators conducthearings at mutually convenient times and places in an informalenvironment. These impartial arbitrators review the positions of theparties, make decisions and, when appropriate, render awards to resolvedisputes. CAMVAP decisions are fas...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is availablefrom your dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can discolor and s...

PAINT CHIPS Your dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jam) toyour dealer to ensure you get the correct color. • Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and in...

PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your dealer. • For routine cleaning, use Motorcraft Detail Wash (ZC-3–A). • If tar or grease spots are present, use Motorcraft Bug and TarRemover (ZC-42). WINDOWS AND WIPER BLADES...

INTERIOR For fabric, carpets, cloth seats, safety belts and seats equipped with sideair bags: • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Motorcraft Extra StrengthUpholstery Cleaner (ZC-41). • If grease or tar is present on the material, spot-clean the are...

FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Your Ford, Lincoln or Mercury dealer has many quality products availableto clean your vehicle and protect its finishes. These quality productshave been specifically engineered to fulfill your automotive needs; theyare custom designed to complement the styl...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a scheduled maintenance guide which makes trackingroutine service easy. If your vehicle requires professional service, your dealership can providethe...

• Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N(Neutral). 2. Block the wheels. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease h...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.0L I4 SPI 1. Power steering fluid reservoir 2. Engine oil dipstick 3. Engine oil filler cap 4. Brake/Clutch fluid reservoir 5. Power distribution box 6. Air filter assembly 7. Windshield washer fluid reservoir 8. Battery 9. Automatic transaxle fluid...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16–A2.Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic c...

5. Locate and carefully remove the engine oil indicator (dipstick). • 2.0L SPI/2.3L I4engine • 2.0L Zetec engine 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is between the MIN and MAX marks (2.0L SPI/2.3 engine) or between ADD and FULL (2.0L Zetec...

• 2.0L Zetec • 2.3L I4 • If the oil level is below the MIN/ADD mark, add enough oil to raise thelevel within the MIN-MAX/ADD-FULL range. • Oil levels above the MAX/FULL mark may cause engine damage. Someoil must be removed from the engine by a service technician. 7. Put the indicator back in and ens...

3. Recheck the engine oil level. Make sure the oil level is not above theMAX mark on the engine oil level indicator (dipstick). 4. Install the indicator and ensure it is fully seated. 5. Fully install the engine oil filler cap by turning the filler cap clockwisetightly until clicks are heard, or unt...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. However, for severe usage or in high temperature climates, check thebattery electrolyte level. Refer to the scheduled maintenance guide forthe service ...

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.Lift the battery with a battery carrier or with your hands on oppositecorners. Keep batteries out of reach of ...

If the battery has been disconnected or a new battery has been installed,the clock and the preset radio stations must be reset once the battery isreconnected. • Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “cold fill level” or within the “coldfill range” as listed on the engine coolant reservoir (depending uponapplication). • Refer to the Scheduled Maintenance Guide for service interval...

• Add Motorcraft Premium Gold Engine Coolant(yellow-colored), VC-7–A (U.S., except CA and OR), VC-7–B(CA and OR only), meeting Ford SpecificationWSS-M97B51–A1. Note: Use of Motorcraft Cooling System Stop Leak Pellets, VC-6, may darken the color of Motorcraft Premium Gold Engine Coolant fromyellow to...

2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the coolant reservoir (a translucent plastic bottle).Slowly turn cap counterclockwise (left) until pressure begins to release. 3. Step back while the pressure releases. 4. When you are sure that all the pressure ...

• NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% willdecrease the overheat protection characteristics of the enginecoolant and may cause engine damage. • Refer to the chart on the coolant container to ensure thecoolant concentration in your ve...

When this occurs the vehicle will still operate. However: • The engine power will be limited. • The air conditioning system will be disabled. Continued operation will increase the engine temperature: • The engine will completely shut down. • Steering and braking effort will increase. Once the engine...

clothing and wash skin thoroughly with soap and water. Repeated orprolonged skin contact with fuel liquid or vapor causes skin irritation. • Be particularly careful if you are taking “Antabuse” or other forms ofdisulfiram for the treatment of alcoholism. Breathing gasoline vapors,or skin contact cou...

Fuel quality If you are experiencing starting, rough idle or hesitation driveabilityproblems during a cold start, try a different brand of unleaded gasoline.“Premium” unleaded gasoline is not recommended for vehicles designedto use “Regular” unleaded gasoline because it may cause these problemsto be...

ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, thedriver. You must gather information as accurately and consistently aspossible. Fuel expense, frequency of fill-ups or fuel gauge readings areNOT accurate as a measure of fuel eco...

2. Each time you fill the tank, record the amount of fuel added (in litersor gallons). 3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current odometer reading. 4. Subtract your initial odometer reading from the current odometerreading. 5. Follow one of the simple cal...

• Warming up a vehicle on cold mornings is not required and mayreduce fuel economy. • Resting your foot on the brake pedal while driving may reduce fueleconomy. • Combine errands and minimize stop-and-go driving. Maintenance • Keep tires properly inflated and use only recommended size. • Operating a...

It is important to note the box in the lower left corner of the windowsticker. These numbers represent the Range of L/100 km (MPG)expected on the vehicle under optimum conditions. Your fuel economymay vary depending upon the method of operation and conditions. EMISSION CONTROL SYSTEM Your vehicle is...

condition. To ready the on-board diagnostics system for I/M testing, aminimum of 30 minutes of city and highway driving is necessary asdescribed below: • First, at least 10 minutes of driving on an expressway or highway. • Next, at least 20 minutes driving in stop-and-go, city-type traffic withat le...

The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels between the “MIN” and“MAX” lines are within the normaloperating range, there is no need toadd fluid. If the fluid levels areoutside of the normal operatingrange, the performance of yo...

Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug andinspect the fluid level. 3. Fluid level should be at thebottom of the opening. 4. Add enough fluid through thefiller opening so that the fluid levelis at the bottom of the opening. 5. I...

Information on “P” type tires P215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (Note thatthe tire size, load index and speedrating for your vehicle may bedifferent than this example.) 1. P: Indicates a tire, designated by the Tir...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation than those of “P” typetires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon li...

Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask a qualified technician at a Ford or Lincoln/Mercury dealership to check for and correct any wheelmisalignment, tire imbalance or mechanical problem involved before tirerotation. Note: After...

Safety practices Driving habits have a great deal to do with your tire mileage and safety. • Observe posted speed limits • Avoid fast starts, stops and turns • Avoid potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking If you vehicle is stuck in snow, ...

For PCV valve replacement, see your dealer or a qualified servicetechnician. Refer to the scheduled maintenance guide for the appropriateintervals for changing the PCV valve. Replace the PCV valve with one that meets Ford material anddesign specifications for your vehicle, such as a Motorcraft orequ...

Some transmission fluids may be labeled as dual usage, such asMERCON 威 and MERCON 威 V. These dual usage fluids are not to be used in an automatic transmission that requires use of the MERCON 威 type fluid. However, these dual usage fluids may be used in transmissions thatrequire the MERCON 威 V type f...

Item Ford PartName orEquivalent Ford PartNumber FordSpecification Automatictransaxle MotorcraftMERCON 威 V ATF XT-5-QM MERCON 威 V Manual transaxle Motorcraft Full SyntheticManualTransmissionFluid XT-M5-QS WSD-M2C200–C Engine oil Motorcraft SAE5W-20 PremiumSynthetic BlendMotor Oil (US)Motorcraft SAE5W...

ENGINE DATA Engine 2.0L SPIengine 2.0L Zetec Eengine 2.3L I4 engine Cubic inches 121 121 138 Required fuel 87 octane 87 octane 87 octane Firing order 1–3–4–2 1–3–4–2 1–3–4–2 Spark plug gap 1.4 mm (0.054inch) 1.3 mm (0.051inch) 1.3 mm (0.051inch) Ignition system ElectronicIgnition ElectronicIgnition ...

• Coupe 2004 Focus (foc) Owners Guide (post-2002-fmt)USA English (fus) Maintenance and Specifications 214

• Wagon IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedto a vehicle and prescribe where theCertification label may be located.The Certification label is located onthe front door latch pillar on th...

Vehicle identification number (VIN) The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Please note thatin the graphic XXXX isrepresentative of your vehicleidentification number.) 1. World manufacturer identifier 2. Brake type and gross vehi...

Transmission/Transaxle code designations You can find a transmission/transaxle code on the vehicle certificationlabel which is located on the door pillar. The following table tells youwhich transmission or transaxle each code represents. Truck application: Code Transmission Description Manual transm...

Code Transmission Description Electric H One speed electric D Automatic 5–speed overdrive (5R44E) R Automatic 5–speed overdrive (5R55S) Passenger car application: Code Transmission/Transaxle Description Front wheel drive manual transaxle R 5–speed overdrive (MTX75) W 5–speed overdrive (M5) Front whe...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford or Ford of Canada dealer.These quality accessories have been specifically engineered to fulfill yourautomotive needs; they are custom designed to co...

A Air bag supplemental restraintsystem ..............................89–90, 93 and child safety seats ..............91description ..........................90, 93disposal ......................................95driver air bag ......................91, 94indicator light ...........................93o...