Ford 2004 Expedition v.1- Manuals

SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury and prevent possibledamage to others, your vehicle and its equipment? In this guide, answersto such questions are contained in comments highlighted by the warningtriangle symbol. These comm...

SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and 6.0LPower Stroke Diesel Engine Coverage. In addition, your vehicle is eligiblefor Emissions Defect and Emissions Performance Warranties. For adetai...

Front seat mounted rear facing child or infant seats should NEVER be used in front of a passenger side air bag unless the air bag can be and is turned OFF. Using your vehicle with a snowplow Do not use this vehicle for snowplowing. Your vehicle is not equipped with a snowplowing package. Notice to o...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -No...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

when the ignition is turned to the ON position. If the brake systemwarning light does not illuminate at this time, seek service immediatelyfrom your dealership. Illumination after releasing the parking brakeindicates low brake fluid level and the brake system should be inspectedimmediately by your s...

Low tire warning: Illuminates when the low tire warning system isenabled. If the light remains onwhile driving, the tire pressureshould be checked, refer to Low tire warning in the Maintenance and Specifications chapter. If this light fails to illuminate when ignition is turned to ON, continues to f...

Speed control: Illuminates when the speed control is activated. Turnsoff when the speed control systemis deactivated. O/D off: Illuminates when the overdrive function of thetransmission has been turned off,refer to the Driving chapter. If the light flashes steadily or does not illuminate, have the t...

Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in the ignition) and thedriver’s door is opened. Door ajar warning chime: Sounds when any door, liftgate or the liftgate glass is opened (or not fully closed). GAUGES Speedometer: Indic...

Battery voltage gauge: Indicates the battery voltage when theignition is in the ON position. If thepointer moves and stays outside thenormal operating range (asindicated by arrows), have thevehicle’s electrical system checkedas soon as possible. Engine oil pressure gauge: Indicates engine oil pressu...

PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD (IF EQUIPPED) 1. EJ (Eject): Press to stop and eject a tape. 2. EJ (Eject): Press to stop and eject a CD. 3. BASS: Allows you to increase or decrease the audio system’s bassoutput. Press BASS then press SELto decrease or increase the bass levels. TREB (Treble)...

In CD mode, REW control reverses the CD within the current track. FF (Fast Forward): Works in tape and CD modes. In the tape mode, tape directionautomatically reverses when the end of the tape is reached. In CD mode, FF advances the CD within the current track. 10. MUTE: Press to mute the playing me...

11. AUTOSET: Press to set first six strong stations into AM, FM1 orFM2 memory buttons; press again toreturn to the original presetstations. If there are less than six strong stations available on thefrequency band, the remaining memory preset controls will all store thelast strong station available....

PREMIUM IN-DASH SIX CD SOUND SYSTEM AUDIOPHILE SATELLITE READY AM/FM STEREO IN-DASH SIX CDRADIO 1. Seek: Press and release SEEK / for previous/next strong station, selection or track. 2004 Expedition (exd) Owners Guide (post-2002-fmt)USA English (fus) Entertainment Systems 22

Treble: Press TREB; then press SEL / to decrease/increase the treble output. 7. Select: Use with Bass, Treble, Balance and Fade controls to adjustlevels and set the clock. 8. Balance: Press BAL; then press SEL / to shift sound to the left/right speakers. Fade: Press FADE; then press SEL / to shift s...

COMP OFF is displayed. Press the SEL control again to disable thefeature when COMP ON is displayed. Setting the clock: Press MENU until SELECT HOUR or SELECT MINUTE is displayed. Use SEL to manually increase ( ) or decrease ( ) the hours/minutes. Press MENU again to disengage clock mode. 10. Memory ...

The rear speakers will cut out once the speaker on/off control is pressed.The front speaker will remain playing for the front passengers. Press thecontrol again to deactivate the headphones. SINGLE PLAY illuminates inthe radio display and the fade control is enabled, signaling that Dual Playmode has...

Seek function • In radio mode, press to find the next listenable station downthe frequency band. • In radio mode, press to find the next listenable station up thefrequency band. • In tape mode (if equipped), use theSEEK function to access thenext or previous selection. • In CD mode (if equipped), us...

AUDIO SYSTEM WARRANTY AND SERVICE Refer to the Warranty Guide for audio system warranty information. If service is necessary, see your dealer or qualified technician. Whenever a warning is received, the radio volume will be loweredto a volume that will allow the tones to be heard. The radiovolume wi...

Press to playback or pause the DVD. 3. DIM control Adjust to increase (+) or decrease (-) the amount of brightness on thescreen. 4. ENTER control Press to select the function pointed to within the active menu. May alsobe used by some user interactive discs during movie play. 5. MENU control Press to...

In stop mode, press to change to a different playing media (e.g. AM, FM,CD . . . ) 8. VOLUME control Press to increase (+) or decrease (-) volume level. Battery replacement Batteries are supplied with theremote control unit. Since allbatteries have a limited shelf life,replace them when the unit fai...

Liquid Crystal Display (LCD) flip-down screen The screen rotates down to view and into the housing to store when notin use. Be sure the screen is latched into the housing when being stored. 1. 7.0” (diagonal) active matrix liquid crystal display (LCD) screen.2. Screen housing.3. Dimmer switch. Press...

• When the temperature of the DVD player becomes too hot, the hightemperature sensor circuit stops machine operation. DVD/CD HOT willilluminate in the radio display. • The DVD player will remain inactive until it cools to a normaloperating temperature. Length of time to cool will vary depending onco...

Removing a CD/DVD 1. Press the STOP/EJECT control to stop playback. 2. Press the STOP/EJECT control again to eject the CD/DVD. If the CD/DVD is not removed within the allotted time, the system willpull the CD/DVD back into the system for safety purposes. If theCD/DVD will not eject from the system, ...

4. DVD/ CD STATUS (PLAY/FF/REW/PAUSE) 5. AUDIO OUTPUT (not changeable) 6. Subtitles (specific language type - English or Spanish, dependent ondisc capability and ON/OFF selection.) 7. Camera angle (of picture) - Adjustable with cursor controls andENTER control. Safety information Read all of the saf...

Federal Communication Commission (FCC) Compliance Changes or modifications not approved by Ford Motor Company couldvoid user’s authority to operate the equipment. This equipment has beentested and found to comply with the limits for a Class B digital device,pursuant to Part 15 of the FCC Rules. Thes...

Cleaning the liquid crystal display (LCD) flip-down screen Clean the display screen by applying a small amount of water or anyammonia-based household glass cleaner directly to a soft cloth. Rub thescreen gently until the dust, dirt or fingerprints are removed. Do notspray the screen directly with wa...

• Set the volume level so that you can hear directions clearly. • Do not disassemble or modify the system as this may lead to damageand void your warranty. If a problem occurs, stop using the systemimmediately and contact your Ford or Lincoln Mercury Dealer. System overview 1. HOME: When the home lo...

2. Press the AM/FM control to selectthe desired frequency band. 3. Press the SEEK control to locatea station. To play a CD in the VNR: 1. Ensure that the ignition and theVNR system are ON. 2. Insert a CD into the single slot ofthe VNR and the CD will automatically begin play. If a CD is alreadyloade...

2. Press the NAV control to enterinto Navigation mode. 3. To enter a destination, ensurethat the vehicle is in the PARK position. 4. To navigate to home from thecurrent location, press HOME. If ahome location has not previouslybeen stored, pressing and holdingHOME will store the home location. Audio...

AM/FM select The AM/FM control works in radio,CD and navigation modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press thecontrol to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in CD mode Press to stop CD play and begin radio play. ...

If a navigation CD is in the head unit and you press CD, the system willautomatically search for an audio CD in the CD DJ and begin play if it ispresent. Adjusting the levels 1. Press the MENU control. 2. Select the AUDIO OPTIONS softkey. 3. Select BASS, TREB, BAL orFADE. The bass adjust allows you ...

(STOP) / AUX — If a DVD movie is playing, press to stop. If a movie is not playing, press to activate AUX mode. CD DJ Your vehicle is equipped with a CD DJ (CD changer). It is located in thecenter console. Radio power must be turned on to play the CDs in the CD DJ. Themagazine may be stored in the g...

will disable rear seat control (headphone/speaker icon on display willappear with a red slash through it). When RSC is active, pressing presets 2 and 4 simultaneously on the radiowill enable Dual Play mode (or the RSC can enable Dual Play mode bypressing the / button). The front speakers play the se...

• Within a Town/City – Lists entries for a specific city in alphabetical order. Certain categories may not be available in some areas and POIs may notall be listed. Up to date information also depends upon using the latestnavigation CD available. Previous destination The last 50 destinations entered...

• Resume route - The navigationsystem displays the Select RouteCriteria screen. Refer to Selecting Route Criteria earlier in this chapter. • Cancel route - Press to return tothe main menu. If the ignition is not turned off,simply continue along your highlighted route. Route changes or cancellations ...

5. Select the SET soft key to synchronize/set the minutes and seconds toGPS time. The hours will remain at the user set value. You may choose to set the clock to a 12 or 24 hour display. General information Federal Communication Commission (FCC) Compliance Changes or modifications not approved by Fo...

MANUAL HEATING AND AIRCONDITIONING SYSTEM 1. Temperature selection: Controls the temperature of theairflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in thevehicle. See the following for a briefdescription on each control. MAX A/C: Uses recirculated air through the...

AUXILIARY A/C-HEATER CONTROLS (IF EQUIPPED) Your vehicle may be equipped with auxiliary climate controls. Theseallow the front or rear seat passengers to control airflow direction,temperature and fan level of the rear compartment to quickly heat orcool the vehicle. Auxiliary climate controls are loc...

Rear auxiliary controls (if equipped): Once the front auxiliary control is set to REAR, the rear seat passengersmay use the rear auxiliary controls in the floor console to make thedesired adjustments. 1. Temperature control: Determines temperature levels. Ifthe main climate control system iscooling ...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parking lamps. Rotate to the secondposition to turn on the headlamps. Foglamp control (if equipped) The headlamp control also operatesthe foglamps. The foglamps can beturned on when the headlamp control is in the , or p...

Daytime running lamps (DRL) (if equipped) Turns the foglamps on at full intensity output. To activate: • the ignition must be in the ON position and • the headlamp control must be in the OFF or Parking lamps position. Always remember to turn on your headlamps at dusk or duringinclement weather. The ...

5. Locate the vertical adjuster oneach headlamp, then use a 10 mmsocket/wrench to turn the adjustereither counterclockwise (to adjustdown) or clockwise (to adjust up)aligning the upper edge of the lightpattern up to the horizontal line. 6. HORIZONTAL AIM IS NOTREQUIRED FOR THIS VEHICLEAND IS NON-ADJ...

Front row dome lamp/ map light (if equipped) The dome lamp lights when: • any door is opened, • the instrument panel dimmerswitch is rotated up until thecourtesy lamps come on, and • any of the remote entry controlsare pressed and the ignition isOFF. The map lights are activated by pressing the cont...

Map lamps To change the map lamp bulbs: 1. Use a small screwdriver toremove the map lamp lens. 2. To remove the old bulb, twist 1 ⁄ 4 turn and pull it out. 3. Twist in a new bulb. 4. Align and press the map lamplens back on and test the lamp operation. Replacing headlamp bulbs 1. Make sure that the ...

Approach lamp bulb removal (if equipped) To change the bulbs: 1. Make sure that all the doors areclosed and the interior lights haveautomatically turned off or theopposite mirror approach lamp hasturned off. 2. With a small flat tippedscrewdriver, insert the tip into theapproach light module slot lo...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Speed dependent wipers: When the wiper control is on, the speed ofthe wipers will automatically adjustwith the vehicle speed. T...

Changing the wiper blades It is recommended that wiper blades are renewed before winter. To replace the wiper blades: 1. Fold back the wiper arm andposition the wiper blade at rightangles to the wiper arm. 2. To remove, press the retainingclip (A) to disengage the wiperblade, then pull the blade dow...

Forward storage bin and conversation mirror (if equipped) The storage compartment may beused to store two pairs of sunglassesor similar objects. Press the releasecontrol to open the storagecompartment. The door will openslightly and can be moved to fullopen. The conversation mirror on thecover allow...

Do not let children play with the moon roof. They may seriouslyhurt themselves. Power quarter rear windows (if equipped) • Without a moon roof • With a moon roof Press the portion of the VENT control to open the power rear quarter windows. Press the portion of the VENT control to close the power rea...

Do not plug optional electricalaccessories into the cigarette lighter.Use the power point. Do not use the power point foroperating the cigarette lighterelement. The Maximum power each powerpoint can supply depends on thefuse rating. For example: a 20A fuseshould supply a maximum of 240Watts, a 15A f...

Accessory delay With accessory delay, the window switches, audio system and moon roofmay be used for up to ten minutes after the ignition switch is turned tothe OFF position or until any door is opened. MIRRORS Automatic dimming rear view mirrors (if equipped) Your vehicle may be equipped with an in...

Heated outside mirrors Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated. Do not remove ice from themirrors with a scraper orattempt to readjust the mirrorglass if it is frozen in place.These actions could causedamage to the glass and mirrors. R...

Fold-away mirrors Pull the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash. POWER ADJUSTABLE FOOT PEDALS The accelerator and brake pedalshould only be adjusted when thevehicle is stopped and the gearshiftlever is in the P (Park) position. Press and hold the ro...

Setting speed control The controls for using your speedcontrol are located on the steeringwheel for your convenience. 1. Press the ON control and releaseit. 2. Accelerate to the desired speed. 3. Press the SET + control andrelease it. 4. Take your foot off the acceleratorpedal. 5. The indicator ligh...

Audio control features Press to select: • AM, FM1, FM2, • CD, or • DVD (if equipped). In AM, FM1, or FM2 mode: • Press MEM to select presetstations within the selected radioband. In CD mode: • Press MEM to select the nextselection on the CD. In any mode: • Press VOL + or − to adjustvolume. 2004 Expe...

Retain the original transmitter for use in other vehicles as well as forfuture programming procedures (i.e. new HomeLink 威 equipped vehicle purchase). It is also suggested that upon the sale of the vehicle, theprogrammed Homelink 威 buttons be erased for security purposes, refer to Programming in thi...

device should activate when the HomeLink 威 button is pressed and released. Note: To program the remaining two HomeLink 威 buttons, begin with step 2 in the “Programming” section — do not repeat step 1. Note: If the red light blinks rapidly for two seconds and then turns to a continuous red, proceed w...

• Proceed with step 4 in the “Programming” section. Operating the HomeLink 姞 Wireless Control System To operate, simply press and releasethe appropriate HomeLink 威 button. Activation will now occur for thetrained product (garage door, gateoperator, security system, entrydoor lock, or home or office ...

ELECTRONIC COMPASS/TEMPERATURE DISPLAY WITHOUTMESSAGE CENTER (IF EQUIPPED) Outside air temperature In vehicles without Dual ElectronicAutomatic Temperature Control(DEATC), the outside temperaturedisplay is contained in theinstrument cluster and displays allthe time. In vehicles with DEATC,the temper...

3. Drive the vehicle slowly (less than 5 km/h [3 mph]) in circles untilCAL indicator turns off. As many as 5 complete circles may be required. 4. The compass is now calibrated. MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position,the message center, located on yourinstrument cluster, di...

1. To disable/enable the autolampdelay feature, select this functionfrom the SETUP control for thecurrent display mode. 2. Press the RESET control to selecta new Autolamp delay value. Reverse Sensing System (if equipped) This feature sounds a warning tone to warn the driver of obstacles nearthe rear...

• Washer fluid • Brake fluid • Compass • Outside temperature • Engine sensor Contact your dealer as soon as possible if these messages occur on aregular basis. CENTER CONSOLE (IF EQUIPPED) The center console offers several useful storage features. These include: 1. Pen holder 2. Tissue holder 3. Cas...

Make sure the liftgate is closed to prevent exhaust fumes frombeing drawn into the vehicle. If you must drive with the liftgate open, keep the vents open so outside air comes into the vehicle. LUGGAGE RACK The rear cross-bar can be adjusted to fit the item being carried. Thefront cross-bar does not ...

KEYS The key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer. You should always carry a second key with you in a safe place in caseyou require it in an emergency. Refer to SecuriLock 娂 Passive Anti-Theft System for more information. POWER DOOR LOCK...

REMOTE ENTRY SYSTEM This device complies with part 15 of the FCC rules and with RS-210 ofIndustry Canada. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) This devicemust accept any interference received, including interference that may...

Replacing the battery The remote entry transmitter uses one coin type three-volt lithiumbattery CR2032 or equivalent. The typical operating range for yourremote entry transmitter is approximately 10 meters (33 feet). Adecrease in the operating range could be caused by: • weather conditions, • nearby...

Replacing lost transmitters If a remote transmitter has been lost and you would like to remove itfrom the vehicle’s memory, or you would like to purchase additionalremote transmitters and have them programmed to your vehicle: • Take all your vehicle’s transmitters to your dealer for programming, or ...

The inside lights will not turn off if: • they have been turned on with the dimmer control, or • any door is open. The battery saver will shut off the interior lamps 30 minutes after theignition has been turned to the OFF position. Smart unlocking feature The smart unlocking feature prevents you fro...

electronically locked by the remote entry transmitter, key pad, or powerdoor control (if pressed while the door was open). The UNLOCK function will operate again after you unlock the vehicleusing the remote entry transmitter or key pad, turn the ignition to ON,or open the door from inside of the veh...

Note: The 5–digit code (e.g. 12345) will be in large, BOLD numbers on the module label. When pressing the controls on the keyless entry keypad, press themiddle of the controls to ensure a good activation. Programming your own personal entry code To program your own code: 6. Enter factory set code (k...

THEFT INDICATOR The theft indicator is the flashing red indicator located on the dashpanel. • When the ignition is in the OFF position, the indicator will flash onceevery 2 seconds to indicate the SecuriLock 娂 system is functioning as a theft deterrent. • When the ignition is in the ON position, the...

devices cannot damage the coded key, but can cause a momentary “no start” condition if they are too close to the key during engine start. If aproblem occurs, turn ignition OFF and restart the engine with all otherobjects on the key ring held away from the ignition key. Check to makesure the coded ke...

key into the ignition and turn the ignition from 1 (OFF) to 3 (ON) (maintain ignition in 3 (ON) for at least three seconds but no more thanten seconds). 4. Turn the ignition from 3 (ON) back to 1 (OFF) in order to remove thesecond coded key from the ignition. 5. Within 10 seconds of removing the sec...

SEATING Adjusting the front manual seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle ismoving. Do not pile cargo higher than the seatbacks to reduce the risk ofinjuring people in a collision or sudden stop. Lift handle to move seat forward orbackward. Seat recliner Alway...

• There is a filter located underboth front seats. • It can be accessed from thesecond row seat. Move the frontseat all the way forward and upto ease access. To remove climate controlled seatair filter: • Remove key from ignition. • Push on the outside rigid edge ofthe air filter at the center andro...

To install climate controlled seat air filter: • First, position the filter in it’shousing making sure that the farforward end is all the way up inthe housing. Then push in on thecenter of the outside edge of thefilter and rotate up into thehousing until it clips into position. REAR SEATS Second row...

3. To return the seat to a seatingposition, push down on the seatuntil the seat is latched to the floor. 4. With the seat in the flat back position, lift up on the lever located onthe side of the seat cushion. This will allow the seat back to be lifted tothe upright locked position. 5. Lift the seat...

1. Locate the handle on the side ofthe seat, lifting it to release theseatback. 2. Ensure that the seat back islocked in the down position byapplying pressure to the seat back. 3. Locate the latch strap at the frontof the seat and pull to release theseat into a kneel down load floorposition. A moder...

The rear latch hooks mustbe properly engaged with the floor striker. Position the rearlegs of the seat over the floorstrikers and engage. 2. With the seat in the flat back position, lift up on the lever locatedon the side of the seat cushion. Thiswill allow the seat back to be liftedto the upright l...

Reclining the second row 40% seatback Locate the release handle located onthe outboard side of the seatcushion and lift gently to allow theseatback to be adjusted to thedesired location. Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal i...

Pull up on the handle locatedbehind the seatback while pushingthe seatback forward and down intothe seat cushion. To return the seatback to its originalposition lift the seatback until itlatches into place. Third row power folding seat (if equipped) The control buttons are located on the right-hand ...

Push the top of the control buttonto return the seatback to its originalposition. The power folding seats are designed to stall within 1–10 secondsof encountering an obstruction when opening or closing. Shouldthis occur, remove the obstruction and wait approximately 1–4minutes for the seat motor to ...

If any of these things happen, even intermittently, have the PersonalSafety System serviced at your dealership or by a qualified technicianimmediately. Unless serviced, the system may not function properly inthe event of a collision. Safety restraints precautions Always drive and ride with your seat...

Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints. Safety belts and seats can become hot in a vehicle that has beenclosed up in sunny weather; they could burn a small child. Check seat covers and buckles before you place a child any...

2. To unfasten, push the releasebutton and remove the tongue fromthe buckle. The front outboard, rear outboard, and second and third row centersafety restraints in the vehicle are combination lap and shoulder belts.The front center safety restraint (if equipped) is a manually-adjustablelap belt. All...

BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED ifthe safety belt assembly “automatic locking retractor” feature or any other safety belt function is not operating properly. In addition, allsafety belts should be checked for proper function. Failure to replacethe belt and retractor assembly could incre...

Front and second row safety belt height adjustment Your vehicle has safety belt heightadjustments for the driver, rightfront passenger and second rowoutboard passengers. Adjust theheight of the shoulder belt so thebelt rests across the middle of yourshoulder. To lower the shoulder belt height,push t...

Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a right angle to the beltand pull across your lap until itreaches the buckle. To tighten thebelt, pull the loose end of the beltthrough the tongue until it ...

If... Then... The driver’s safety belt isbuckled before the ignitionswitch is turned to the ONposition... The BeltMinder 娂 feature will not activate. The purpose of the BeltMinder 娂 is to remind occasional wearers to wear safety belts all of the time. The following are reasons most often given for n...

Reasons given... Consider... “Belts wrinkle my clothes” Possibly, but a serious crash can domuch more than wrinkle your clothes,particularly if you are unbelted. “The people I’m with don’twear belts” Set the example, teen deaths occur 4times more often in vehicles withTWO or MORE people. Children an...

• The ignition switch is in the OFF position • All vehicle doors are closed • The driver’s safety belt is unbuckled • The parklamps/headlamps are in OFF position (If vehicle is equippedwith Autolamps, this will not affect the procedure.) To reduce the risk of injury, do not deactivate/activate theBe...

Use only extensions manufactured by the same supplier as the safetybelt. Manufacturer identification is located at the end of the webbing onthe label. Also, use the safety belt extension only if the safety belt is tooshort for you when fully extended. Do not use extensions to change the fit of the s...

Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries. Airbags DO NOT inflate slowly; there isa risk of injury from a deploying airbag. All occupants of the vehicle, including the driver, should a...

Do not attempt to service, repair, or modify the air bagsupplemental restraint systems or its fuses. See your Ford or Lincoln Mercury dealer. The front passenger air bag is not designed to offer protection toan occupant in the center front seating position. Modifying or adding equipment to the front...

How does the air bag supplemental restraint system work? The air bag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration sufficientto cause the sensors to close anelectrical circuit that initiates airbag inflation. The fact that the air bags did notinflate in a collision do...

Several air bag system components get hot after inflation. Do nottouch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in acollision. The SRS ...

Safety Canopy 姟 system (if equipped) Do not place objects ormount equipment on or near the headliner at the siderailthat may come into contact with adeploying Safety Canopy 娂 . Failure to follow these instructions mayincrease the risk of personal injuryin the event of a collision. Do not lean your h...

How does the Safety Canopy 姟 system work? The design and development of theSafety Canopy 娂 system included recommended testing proceduresthat were developed by a group ofautomotive safety experts known asthe Side Air Bag Technical WorkingGroup. These recommended testingprocedures help reduce the ris...

Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Refer to the Air bag readiness section in the Instrument Cluster chapter. Routine maintenance of the air bag is not required. Any difficulty with the sy...

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant orchild restraint you might use. Children and safety belts If the child is the pro...

When children should use booster seats Children need to use booster seats from the time they outgrow thetoddler seat until they are big enough for the vehicle seat andlap/shoulder belt to fit properly. Generally this is when they weigh about80 lbs (about 8 to 12 years old). Booster seats should be u...

• Those with a high back. If, with a backless booster seat,you cannot find a seating positionthat adequately supports yourchild’s head, a high back boosterseat would be a better choice. Both can be used in any vehicle in a seating position equipped withlap/shoulder belts if your child is over 40 lbs...

SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all of the manufacturer’s instructions with thesafety seat you put in your vehicle. If you do not install and use thesafety seat properly, the ...

• The second row center seat can be moved forward to keep a child in achild restraint close to the front seat occupants. The seat should bemoved to the full rearward position when it is occupied by olderchildren or adults. • LATCH lower anchors are recommended for use by children up to22 kg (48 poun...

6. Before placing the child into the child seat, forcibly move the childseat from side to side and forward to make sure that the seat is heldsecurely. If the child seat moves excessively, repeat steps 5 through 6, orproperly install the child seat in a different position. Attaching child safety seat...

Second row seating positions 1. Position the child safety seat on the seat cushion. 2. Locate the tether anchor at the bottom back of the seat. • outboard seating positions • center seating position (ifequipped) 3. Route the child safety seat tether strap under the head restraint(outboard seats) and...

5. Rotate the tether strap, and clipthe tether strap to the anchor onthe seat frame. 6. Rotate the tether strap clip. 7. Tighten the child safety seat tether strap according to themanufacturer’s instructions. Third row seating position 1. Position the child safety seat on the center of the seat cush...

STARTING Positions of the ignition 1. OFF/LOCK, locks the steeringwheel, automatic transmissiongearshift lever and allows keyremoval. 2. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 3. ON, all electrical circuitsoperational. Warning lightsil...

5. Turn the key to 3 (ON) withoutturning the key to 4 (START). Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate. Starting the engine Note: Whenever yo...

Note: If the engine does not start within five seconds on the first try, turn the key to OFF, wait 10 seconds and try again. If the engine stillfails to start, press the accelerator to the floor and try again; this willallow the engine to crank with the fuel shut off in case the engine isflooded wit...

BRAKES Your service brakes are self-adjusting. Refer to the scheduledmaintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate aperformance concern with the vehicle’s brake system. In normaloperation, automotive brake systems may emit occasional or int...

• The anti-lock system does not always reduce stopping distance.Always leave enough room between your vehicle and the vehicle infront of you to stop. • We recommend that you familiarize yourself with this brakingtechnique. However, avoid taking any unnecessary risks. ABS warning lamp ABS The ABS war...

The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released. If the parking brake is fully released, but the brake warning lampremains illuminated, the brakes may not be working properly. See your dealer or a q...

If the power steering system breaks down (or if the engine is turnedoff), you can steer the vehicle manually, but it takes more effort. If the steering wanders or pulls, check for: • Underinflated tire(s) on any wheel(s) • Uneven vehicle loading • High crown in center of road • High crosswinds • Whe...

LIMITED-SLIP AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly whenone wheel is on a poor traction surface. Under normal conditions, thelimited slip axle functions like a standard rear axle. Extended use of other than the manufacturer’s specified size tires on a...

• Entering a paved road from a gravel road, or vice versa • Hitting a curb while turning • Driving on slick surfaces • Cornering while towing a heavily loaded trailer (refer to Trailer Towing in this chapter) The AdvanceTrac 娂 system automatically turns on when the engine is started. However, the sy...

• A slight deceleration of the vehicle • The AdvanceTrac 娂 indicator light will flash • If your foot is on the brake pedal, you will feel a vibration in thepedal. • If the driving condition is severe and your foot is not on the brake, thebrake pedal will move to apply higher brake forces. You may al...

3. Locate the round access plug onthe underside of the steeringcolumn cover. 4. Remove the access plug using a flat-head screwdriver, then insert yourfinger and pull the override button toward you. With the button pulledtoward you, apply the brake pedal and shift the transmission into N(Neutral). 5....

(Overdrive) The normal driving position for thebest fuel economy. Transmissionoperates in gears one through four. (Overdrive) can be deactivated by pressing the transmission controlswitch (TCS) on the end of thegearshift lever. The transmission control indicatorlight (TCIL) will illuminate in theins...

1 (First) Use 1 (Low) to provide maximumengine braking on steepdowngrades. Upshifts can be madeby shifting to 2 (Second) or to (Overdrive). Selecting 1 (Low) at higher speeds causes the transmission to shift to a lower gear, and willshift to 1 (Low) after vehicle decelerates to the proper speed. For...

To help avoid personal injury, please read and understand thelimitations of the reverse sensing system as contained in this section. Reverse sensing is only an aid for some (generally large andfixed) objects when moving in reverse on a flat surface at “parkingspeeds”. Inclement weather may also affe...

CONTROL TRAC FOUR-WHEEL DRIVE (4X4) OPERATION(IF EQUIPPED) For important information regarding safe operation of this typeof vehicle, see Preparing to drive your vehicle in this chapter. If equipped with the Control Trac 4x4 System, and 4L (4x4 LOW)is selected while the vehicle is moving, the system...

Positions of the Control Trac system The Control Trac system functionsin four modes: • 2H (2WD HIGH) delivers power to the rear wheels only. This isappropriate for normal on-roaddriving on dry pavement. • A4WD (4X4 AUTO) provides electronic control four-wheeldrive with power delivered to allfour whe...

Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily underoff-road conditions. Avoid sharp turns or abrupt maneuvers in thesevehicles. Note: The Control Trac selector knob s...

Shifting from 2H, A4WD or 4H to 4L 1. Bring the vehicle to a stop andkeep the brake pedal depressed. 2. Place the gearshift in N (Neutral). 3. Move the control to the 4Lposition. Note: Some noise may be heard as the system shifts or engages. Shifting from 4L to 4H, A4WD or 2H 1. Bring the vehicle to...

Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any morethan low-slung sports cars are desig...

called for. Avoid abrupt steering, acceleration or braking which couldresult in an increased risk of loss of vehicle control, vehicle rolloverand/or personal injury. Use all available road surface to return thevehicle to a safe direction of travel. • In the event of an emergency stop, avoid skidding...

If the transmission, transfer case or front axle are submerged in water,their fluids should be checked and changed, if necessary. Driving through deep water may damage the transmission. If the front or rear axle is submerged in water, the axle lubricant shouldbe replaced. After driving through mud, ...

Each day before you drive, checkyour tires. If one looks lower thanthe others, use a tire gauge to checkpressure of all tires, and adjust ifrequired. Check tire pressure with atire gauge every few weeks(including spare). Safe operationrequires tires that are neitherunderinflated nor a vehicle which ...

• Maximum Trailer Weight: Maximum weight of a trailer the loaded vehicle (including occupants and cargo) is permitted to tow. It isdetermined by subtracting the weight of the loaded trailer towingvehicle from the GCWR for the towing vehicle. • Trailer Weight Range: Specified weight range that the tr...

Loaded vehicles, with a higher center of gravity, may handledifferently than unloaded vehicles. Extra precautions, such as slower speeds and increased stopping distance, should be taken whendriving a heavily loaded vehicle. Your vehicle has the capability to haul more cargo and people than mostpasse...

Engine Rear axle ratio Maximum GCWR - kg (lbs.) Trailer weight range (0 - maximum) kg (lbs.) 5.4L with optional trailer tow package All 6576 (14500) 0–4059 (0–8950) 4x4 4.6L All 4853 (10700) 0–2268 (0–5000) 5.4L with standard trailer tow package All 5397 (11900) 0–2721 (0–6000) 5.4L with optional tr...

Load equalizing hitch When hooking up a trailer using a load equalizing hitch, always use thefollowing procedure: 1. Park the unloaded vehicle on a level surface. With the ignition in theON position, apply the brake and place the gearshift lever in(Overdrive) for 10 seconds, then return the gearshif...

The braking system of the tow vehicle is rated for operation at theGVWR not GCWR. Trailer lamps Trailer lamps are required on most towed vehicles. Make sure all runninglights, brake lights, turn signals and hazard lights are working. See yourdealer or trailer rental agency for proper instructions an...

• Vehicles with trailers should not be parked on a grade. If you mustpark on a grade, place wheel chocks under the trailer’s wheels. Launching or retrieving a boat Disconnect the wiring to the trailer before backing the trailerinto the water. Reconnect the wiring to the trailer after thetrailer is r...

Vehicles equipped with Control Trac four-wheel drive system: Vehicles equipped with the Control Trac four-wheel drive system cannotbe towed with any wheels on the ground. See your local dealer if youmust flat-tow a vehicle equipped with the Control Trac four-wheel drivesystem. 2004 Expedition (exd) ...

GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the New Vehicle Limited...

The fuel pump shut-off switch has ared reset button on top of it and islocated beneath the air suspensionswitch (if equipped). If the vehicleis not equipped with air suspension,the fuel pump shut-off switch’s redreset button will still be visiblebehind this access panel. Use the following procedure ...

Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wiredamage and could start a fire. Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link ca...

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 10A* Run/Accessory - Front wipermotor, Instrument cluster, Rearwiper motor, Tire PressureMonitor System (TPMS) module 2 20A* Turn signal/Hazard flasher,Stoplamp switch, IVD(AdvanceTrac)...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 4 15A* DVD player, Rear seat audiocontrols, CDDJ (navigation radio) 5 7.5A* Powertrain Control Module (PCM)(KA power), Speed controldeactivation switch, Manualclimate control mode switch,Stoplamp switch, Brake-shiftinte...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 18 10A* Auxiliary A/C temperature blenddoor actuator, Auxiliary A/C frontauxiliary control, Turn signalflasher, Electrochromatic mirror,Auxiliary mode motor, Climatecontrolled seat modules 19 10A* Restraints Control Mod...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 27 5A* Compass module, Reverse sensingsystem module, Brake shiftinterlock (BSI) solenoid,Overdrive cancel switch, Airsuspension module (Run/Startsense) 28 5A* PCM relay coil, Speed controlrelay coil, SecuriLock transcei...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 38 25A* Rear wiper motor, Washer pump(rear window wash) 39 20A* Console power points (front andrear of console), Instrument panelpower point (bench seat) 40 20A* DRL relays, DRL foglamps, DRLheadlamp relay coil, Headlam...

CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel firmlyand slowly move to a safe place on the side of the road. The use of tire sealants may damage your tires. The use of tiresealants may also dama...

3. Unsnap the wheel lug nut wrench, jack extension and handle from theplastic tray. Remove the jack and instruction sheet from the trayassembly. Removing the spare tire 1. Fold the rear seat down. Refer to Rear seats in the Seating and safety restraints chapter. 2. Remove the jack handle andwinch ex...

• Never use the front or rear differential as a jacking point. 6. Remove the lug nuts with the lug wrench. 7. Replace the flat tire with the spare tire, making sure the valve stem isfacing outward. Reinstall the lug nuts until the wheel is snug against thehub. Do not fully tighten the lug nuts until...

5. Disassemble the tools and snap them back into the tool tray. Close theaccess hole with the rubber plug. Reinstall the tray into the vehicle andsecure it with the wing nut (turn clockwise until tight). Wheel lug nut torque specifications Retighten the lug nuts to the specified torque at 800 km (50...

will not affect function or durability of the transmission. Over time, theadaptive learning process will fully update transmission operation. 1. Use only a 12–volt supply to start your vehicle. 2. Do not disconnect the battery of the disabled vehicle as this coulddamage the vehicle’s electrical syst...

4. Make the final connection of the negative (-) cable to the jumpstarting stud located in the rear of the engine compartment, near thebattery. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-)termin...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Remove the jumper cable on the negative (...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handling your vehicle linewill provide warranty service, we recommend you return to your sellingdealer who wants to ensure your continued satisfaction. Pl...

In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action under the Magnuson-MossWarranty Act, or to the extent allowed by state law, before pursuingreplacement or repurchase remedies provided by certain state laws. Thisdispute handling procedure ...

Making a decision Board members review all available information related to eachcomplaint, including oral presentations, and arrive at a fair and impartialdecision. Board review may be terminated at any time by either party. Every effort is made to decide the case within 40 days of the date thatall ...

In the CAMVAP program, impartial third-party arbitrators conducthearings at mutually convenient times and places in an informalenvironment. These impartial arbitrators review the positions of theparties, make decisions and, when appropriate, render awards to resolvedisputes. CAMVAP decisions are fas...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is availablefrom your dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can discolor and s...

PAINT CHIPS Your dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jam) toyour dealer to ensure you get the correct color. • Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and in...

WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, substances on thevehicle’s glass or the wiper blades may be the cause. These may includehot wax treatments used by commercial car washes, tree sap, or o...

• Do not use household cleaning products or glass cleaners, which canstain and discolor the fabric and affect the flame retardant abilities ofthe seat materials. Do not use cleaning solvents, bleach or dye on the vehicle’sseatbelts, as these actions may weaken the belt webbing. CLEANING THE CLIMATE ...

Motorcraft Custom Clearcoat Polish (ZC–8–A) Motorcraft Custom Vinyl Protectant (not available in Canada) (ZC-40–A) Motorcraft Vinyl Cleaner (Canada only) (CXC-93) Motorcraft Vinyl Conditioner (Canada only) (CXC-94) Motorcraft Deluxe Leather and Vinyl Cleaner (not available in Canada)(ZC-11–A) Motorc...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a scheduled maintenance guide which makes trackingroutine service easy. If your vehicle requires professional service, your dealership can providethe...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front center ofthe hood. 3. Lift the hood until the liftcylinders hold it open. 2004 Expediti...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.6L V8 engines 1. Battery 2. Automatic transmission fluid dipstick 3. Engine oil filler cap 4. Power steering fluid reservoir 5. Engine oil dipstick 6. Brake fluid reservoir 7. Engine coolant reservoir 8. Air filter assembly 9. Windshield washer flui...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16–A2.Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic c...

4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove theengine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is between the MIN and MAX marks, the oil level is acceptable. DO NOT ADD OIL...

2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler capand use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil level. Make sure the oil level is not above theMAX mark on the eng...

It is recommended you use the appropriate Motorcraft oil filter (oranother brand meeting Ford specifications) for your engine application. BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. However, for...

Batteries normally produce explosive gases which can causepersonal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery,always shield your face and protect your eyes. Always provide properventilation. When lifting a plastic-case...

battery. When the battery is disconnected or a new battery is installed,the engine must relearn its idle and fuel trim strategy for optimumdriveability and performance. To begin this process: 1. With the vehicle at a complete stop, set the parking brake. 2. Put the gearshift in P (Park), turn off al...

testing is possible with a hydrometer or antifreeze tester (such as theRotunda Battery and Antifreeze Tester, 014–R1060). The level of coolantshould be maintained at the “cold full” of “cold fill range” level in thecoolant reservoir. If the level falls below, add coolant per the instructionsin the A...

If the engine coolant has not been checked at the recommended interval,the engine coolant reservoir may become low or empty. If the reservoir islow or empty, add engine coolant to the reservoir. Refer to Adding engine coolant in this chapter. Note: Automotive fluids are not interchangeable; do not u...

• Do not use alcohol, methanol, brine or any engine coolantsmixed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating orfreezing. • Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosion...

necessary, add enough 50/50 concentration of engine coolant anddistilled water to bring the liquid level to the proper level. If you have to add more than 1.0 liter (1.0 quart) of engine coolant permonth, have your dealer check the engine cooling system. Your coolingsystem may have a leak. Operating...

• Decreased engine coolant concentrations below 40% willdecrease the corrosion protection characteristics of the enginecoolant and may cause engine damage. • Decreased engine coolant concentrations below 40% willdecrease the freeze protection characteristics of the enginecoolant and may cause engine...

Once the engine temperature cools, the engine can be re-started. Takeyour vehicle to a service facility as soon as possible to minimize enginedamage. When fail-safe mode is activated You have limited engine power when in the fail-safe mode, so drive thevehicle with caution. The vehicle will not be a...

When refueling always shut the engine off and never allowsparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions.Care should be taken to avoid inhaling excess fumes. The flow of fuel through a fuel pump nozzle can produce st...

It should not be necessary to add any aftermarket products to your fueltank if you continue to use high quality fuel of the recommended octanerating. Aftermarket products could cause damage to the fuel system.Repairs to correct the effects of using an aftermarket product in yourfuel may not be cover...

possible. Fuel expense, frequency of fill-ups or fuel gauge readings areNOT accurate as a measure of fuel economy. We do not recommendtaking fuel economy measurements during the first 1,600 km (1,000 miles)of driving (engine break-in period). You will get a more accuratemeasurement after 3,000 km–5,...

3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current odometer reading. 4. Subtract your initial odometer reading from the current odometerreading. 5. Follow one of the simple calculations in order to determine fueleconomy: Calculation 1: Multiply liters used by 100...

• Resting your foot on the brake pedal while driving may reduce fueleconomy. • Combine errands and minimize stop-and-go driving. Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fueleconomy. • Use recommended...

It is important to note the box in the lower left corner of the windowsticker. These numbers represent the range of fuel economy expected onthe vehicle under optimum conditions. Your fuel economy may varydepending upon the method of operation and conditions. EMISSION CONTROL SYSTEM Your vehicle is e...

condition. To ready the on-board diagnostics system for I/M testing, aminimum of 30 minutes of city and highway driving is necessary asdescribed below: • First, at least 10 minutes of driving on an expressway or highway. • Next, at least 20 minutes driving in stop-and-go, city-type traffic withat le...

High fluid level Fluid levels above the safe rangemay result in transmission failure.An overfill condition of transmissionfluid may cause shift and/orengagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition. Adjusting automatic transmission fluid levels...

Changing the air filter element 1. Loosen the clamp that securesthe air inlet tube to the engine airfilter cover and disconnect the tubefrom the cover. 2. Loosen the clamp that securesthe air filter cover to the air filterhousing and carefully separate thecover from housing. 3. Remove the air filter...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing thetire’s resistance to the gene...

3. 65: Indicates the aspect ratio which gives the tire’s ratio of height to width. 4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheeldiameter. 6. 95: Indicates the tire’...

which can be found on either the tire label or certification label which islocated on the structure by the trailing edge of the driver’s door or theedge of the driver’s door. The cold inflation pressure should never be setlower than the recommended pressure on the label. Note: You may not find this ...

• Avoid fast starts, stops and turns • Avoid potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking If you vehicle is stuck in snow, mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tirecan ex...

Changing tires with TPMS It is recommended that you alwayshave your tires serviced by a dealeror qualified technician. Each road tire is equipped with a tirepressure sensor mounted on thewheel inside the tire connectedto the valve stem. The tirepressure sensor must be unbolted from the wheel prior t...

Fluid Ford PartName Application Capacity Power steeringfluid MotorcraftMERCON 威 ATF All Fill to line onreservoir Transmissionfluid 1 MotorcraftMERCON 威 V ATF 4R70/75 E-W 13.1L(13.9 quarts) 2 Transfer casefluid MotorcraftMERCON 威 ATF 4x4 vehicles 1.9L(2.0 quarts) Engine coolant 3 MotorcraftPremium Go...

of transmission fluid and fluid level should be set by the indication onthe dipstick’s normal operating range. 3 Add the coolant type originally equipped in your vehicle. 4 Your vehicle’s rear axle is filled with a synthetic rear axle lubricant and is considered lubricated for life. These lubricants...

Transmission/Transaxle code designations You can find a transmission/transaxle code on the vehicle certificationlabel which is located on the door pillar. The following table tells youwhich transmission or transaxle each code represents. Truck application: Code Transmission Description Manual transm...

Passenger car application: Code Transmission/Transaxle Description Front wheel drive manual transaxle R 5–speed overdrive (MTX75) W 5–speed overdrive (M5) Front wheel drive automatic transaxle E 4–speed overdrive (4FE) J 3–speed (Mazda) L 4–speed overdrive (AX4S) P 4–speed overdrive (4F20E) X 4–spee...

FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of genuine Ford accessories are available for yourvehicle through your local authorized Ford or Ford of Canada dealer.These quality accessories have been specifically engineered to fulfill yourautomotive needs; they are custom designed to complement...

A ABS (see Brakes) .....................201 Accessory delay ........................106 Air bag supplemental restraintsystem ........................174–175, 179 and child safety seats ............176description ......................175, 179disposal ....................................182driver air...

F Fail safe cooling ........................295 Floor mats .................................130 Fluid capacities .........................325 Foglamps .....................................87 Four-Wheel Drive vehicles .......217 control trac .............................217description ..................

Oil (see Engine oil) ..................285 P Panic alarm feature,remote entry system ................134 Parking brake ............................202 Parts (see Motorcraft parts) ....325 Pedals (see Poweradjustable foot pedals) .............108 Power adjustable foot pedals ...108 Power distribution...