Ford 2004 Escape v.2- Manuals

to such questions are contained in comments highlighted by the warningtriangle symbol. These comments should be read and observed. Warning symbols on your vehicle When you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempting adjustmentof an...

Special instructions For your added safety, your vehicle is fitted with sophisticated electroniccontrols. Please read the section Supplemental Restraint System (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury...

authority. Other parties may seek to access the informationindependently of Ford Motor Company and Ford of Canada. Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate thanother types of vehicles. Before you drive your vehicle, please...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -No...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

Brake system warning light: To confirm the brake system warninglight is functional, it willmomentarily illuminate when theignition is turned to the ON positionwhen the engine is not running, or in a position between ON and START,or by applying the parking brake when the ignition is turned to the ONp...

Engine oil pressure: Illuminates when the oil pressure falls below thenormal range, refer to Engine oil in the Maintenance and specifications chapter. Low fuel: Illuminates when the fuel level in the fuel tank is at or nearempty (refer to Fuel gauge in this chapter). Overdrive off: Illuminates when ...

AM/FM STEREO / SINGLE CD RADIO (IF EQUIPPED) 1. Balance: Press / to shift sound to the left/right speakers. 2. Fade: Press / to shift sound to the front/rear speakers. 3. SCN (Scan): Press to hear a brief sampling of all listenablestations or CD tracks. Press again tostop. 4. CLK: To set the hour, p...

5. EJ (eject): Press to eject a CD. 6. COMP (Compression): In CD mode, press to bring louder andsofter levels into more comfortablelistening level. The compression icon (c) will appear in the display. 7. Shuffle: Press to listen to the tracks on the CD in random order.Press again to turn off. 8. Mem...

PREMIUM IN-DASH SIX CD SOUND SYSTEM AUDIOPHILE IN-DASH SIX CD SOUND SYSTEM 1. Seek: Press and release SEEK / for previous/next strong station, selection or track. LOAD EJ SHUF MUTE SEL BAL BASS FADE TREB SCAN PUSH ON CD 1 2 3 4 5 6 MENU AMFM SEEK REW FF DISC TUNE 2 3 4 17 16 15 14 13 12 11 10 9 5 6 ...

2. Rewind: In CD mode, press until desired selection is reached. Fast forward: In CD mode, press until desired selection is reached. 3. DSP (Digital Signal Processing) (if equipped): Press to enter DSP mode – allows you toengage/disengage DSP status, andchoose signal modes of JAZZ CLUB, HALL, CHURCH...

Fade: Press FADE; then press SEL / to shift sound to the rear/front speakers. 9. Menu: Press MENU and SEL to access clock mode, RDS on/off,Traffic announcement mode andProgram type mode. On Audiophileaudios, press MENU to access the compression feature. Press SEL toturn the feature ON or OFF. Traffi...

13. Power/volume: Press to turn ON/OFF; turn to increase ordecrease volume levels. Automatic Volume Control (if equipped): Changes the volume automatically and slightly with vehicle speed to compensate for road andwind noise. The recommended level is 1–3. Level 0 turns the speedsensitive volume off ...

MACH 姞 MP3 AUDIO SYSTEM (IF EQUIPPED) 1. Balance: Press / to shift sound to the left/right speakers. 2. Fade: Press / to shift sound to the rear/front speakers. 3. Scan: Press to hear a brief sampling of all listenable radiostations, CD or MP3 tracks. Pressagain to stop. 4. CLK: To set the clock pre...

CD/CD PLAYER CARE Do: • Handle discs by their edges only. Never touch the playing surface. • Inspect discs before playing. Clean only with an approved CD cleanerand wipe from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periodsof time. • Insert more than one ...

HEATER ONLY SYSTEM 1. Fan speed adjustment: Controls the volume of air circulated in thevehicle. 2. Air flow selections: Controls the direction of the airflow in thevehicle. See the following for a briefdescription on each control. : Distributes outside air through the instrument panel vents. : Dist...

Operating tips • To reduce fog build up on the windshield during humid weather, placethe air flow selector in the position. • To reduce humidity build up inside the vehicle: do not drive with theair flow selector in the OFF or MAX A/C position. • Under normal weather conditions, do not leave the air...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parkinglamps. Rotate to the second positionto also turn on the headlamps. HEADLAMP BATTERY SAVER The battery saver will shut off the exterior lamps 10 minutes after theignition switch has been turned off and the headlam...

Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the ON position and • the headlamp control is in the OFF or parking lamp. Always remember to turn on your headlamps at dusk or duringinclement weather. The Daytime Running L...

PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel. • Push and hold top of control tobrighten. • Push and hold bottom of controlto dim. AIMING THE HEADLAMPS The headlamps on your vehicle are properly aimed at the assembly plant.If your vehicle has been in an accident the align...

TURN SIGNAL CONTROL • Push down to activate the leftturn signal. • Push up to activate the right turnsignal. INTERIOR LAMPSDome lamps and map lamps The front dome lamp is located overhead between the driver andpassenger seats. The dome lamp will stay on if thecontrol is moved to the passengerside po...

Replacing the interior bulbs Check the operation of all bulbs frequently. Replacing headlamp bulbs 1. Make sure that the headlamp control is in the OFF position. 2. Open the hood. 3. Press two tabs and disconnect theelectrical connector from the bulb. 4. Remove the rubber boot from thelamp assembly ...

Replacing brake/tail/turn/backup lamp bulbs The brake/tail/turn/backup lamp bulbs are located in the tail lampassembly, one just below the other. Follow the same steps to replaceeither bulb: 1. Make sure the headlamp switch isin the OFF position and then openthe liftgate to expose the lampassemblies...

MULTI-FUNCTION LEVER Windshield wiper: For intermittent operation, move control down oneposition. Adjust the rotary control to thedesired speed setting. For normal or low speed wiperoperation, move control down twopositions from OFF. For high speed wiper operation,move control down three positionsfr...

Rear window wiper/washer controls For intermittent operation of rearwiper, rotate end of control upwardto the INT position. For normal speed rear wiperoperation, rotate control upward toON. To activate the rear washer, rotatethe control to the position and release. Changing the wiper blades 1. Pull ...

• Install the transmitter (6) on to storage compartment door (3)aligning the actuator control (8) with the rubber plunger (1).Close the storage compartment door (3) to verify proper fit. Do notforce the storage compartment door (3) or you may break the doorlatch. If the rubber actuator (1) is the pr...

The mirror will automatically return to the normal high reflective statewhenever the vehicle is placed in R (Reverse). This helps to ensure abright clear view in the mirror when backing up. AUXILIARY POWER POINT Power outlets are designed foraccessory plugs only. Do nothang any type of accessory ora...

One touch down Allows the driver’s window to openfully without holding the controldown. Press completely down onAUTO and release quickly. Pressagain to stop. Window lock (if equipped) The window lock feature disables allthe power windows except thedriver’s. To lock out all the window controlsexcept ...

Reducing speed while using speed control There are two ways to reduce a setspeed: • Press and hold the CST controluntil you get to the desired speed,then release the control. You canalso use the CST control tooperate the Tap-Down function.Press and release this control todecrease the vehicle set spe...

Cell phone use The use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,drivers must not compromise their own or others’ safety when usingsuch equipment. Mobile Communications can enhance personal safetyand security when app...

Do not let children play with the moon roof. They may seriouslyinjure themselves. LIFTGATE To open the rear window, pull theright side of the liftgate handle. To open the liftgate, pull the leftside of the liftgate handle. • Do not open the liftgate orliftgate glass in a garage or otherenclosed area...

To install the shade: • Insert the ends of the cargoshade into the mounting featureslocated behind the rear seat onthe rear trim panels. To operate the shade: 1. Grasp the pull tube at therearward edge of the shade and pullrearward. 2. Secure both ends of the pull tubein the retention slots located ...

NO BOUNDARIES RACK SYSTEM (IF EQUIPPED) Your vehicle may be equipped withan optional roof rack. This uniquefeature allows you to carry cargo onan inner roof rack as well as on theconventional roof rack. Themaximum load for the conventionalroof rack is 45 kg (100 lbs). Theinner rack can also hold 45 ...

6. Figure shows foot (A) clicked into place correctly. 7. With the locking tab (B) exposed on the foot, this figureshows the rack is not installedcorrectly. Repeat steps 3 through5 and secure the rack beforeloading cargo. Do not drive the vehicle if the inner roof rack is extended andloaded with car...

To stow the inner rack: 1. Rotate the handle on the lift barof the inner rack in the direction ofthe arrows on the handle and pullthe inner rack away from thebumper. 2. Lift the inner rack (pivoting atthe hinges). 3. Continue lifting the inner rackuntil it is parallel with the roof. 4. Slide the rac...

Always stow the inner rack on the roof when using an automatedcar wash. Do not attempt to open the liftgate or rear window when the rackis in the down position. This may damage the rack or yourvehicle. To ensure proper sliding function of your rack, keep the rackclear of debris. If debris is visible...

KEYS The key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer. You should always carry a second key with you in a safe place in caseyou require it in an emergency. Refer to SecuriLock 娂 Passive Anti-Theft System for more information. POWER DOOR LOCK...

Locking the doors Turn the key in the door cylinder to lock all the doors. The park lampswill flash once and the perimeter alarm (if equipped) will start thearming process. For more information concerning the perimeter alarm,refer to Perimeter alarm system (if equipped) later in this chapter. If any...

2. Do not wipe off any grease on thebattery terminals on the backsurface of the circuit board. 3. Remove the old battery. 4. Insert the new battery. Refer to the diagram inside the remote entrytransmitter for the correct orientation of the battery. Press the batterydown to ensure that the battery is...

To reprogram the remote entrytransmitters: 1. Ensure the vehicle is electronically unlocked. 2. Put the key in the ignition. 3. Turn the key from the 1 (LOCK) position to 3 (RUN). 4. Cycle eight times rapidly (within 10 seconds) between the 1 (LOCK)position and 3 (RUN). Note: The eighth turn must en...

• after 30 seconds of illumination. The dome lamp control (if equipped) must not be set to the off position for the illuminated entry system to operate. The inside lights will not turn off if: • they have been turned on with the dome lamp control, or • any door is open. The battery saver will shut o...

If a problem occurs with the SecuriLock 娂 system, the indicator will flash rapidly or glow steadily when the ignition is in the ON position. If thisoccurs, the vehicle should be taken to an authorized dealer for service. Automatic arming The vehicle is armed immediatelyafter switching the ignition t...

Disarming the system When you disarm the system, the park lamps will flash twice to indicatethe system has been disarmed. You can disarm the system by any of the following actions: • Unlock the doors by pressing the control on your remote entry transmitter. • Unlock the doors with a key. Turn the ke...

FRONT SEATS Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Adjustable head restraints (...

Adjusting the front manual seat Lift handle to move seat forward orbackward. Pull lever up to adjust seatback. Adjusting the front power seat (if equipped) The control is located on the outboard side of the seat cushion. Press to raise or lower the frontportion of the seat cushion. 2004 Escape (204)...

Press to raise or lower the rearportion of the seat cushion. Press the control to move the seatforward, backward, up or down. Heated seats (if equipped) To operate the heated seats: • Push the control located on theseat to activate. • Push again to deactivate. The heated seats will activate when the...

The head restraints can be movedup and down. Lift the head restraintso that it is located directly or asclose as possible behind your head. Push control to lower or removehead restraint. Reclining the second row seatback Locate the release strip located onthe outboard side of the seatcushion bottom ...

Folding down rear seats 1. Raise the rear seat head restraintand remove. 2. Place the head restraint underthe front seat for storage. 3. Pull the seat release control. NOTE: Make sure the floor is clear of all objects before folding the seat. 2004 Escape (204) Owners Guide (post-2002-fmt)USA English...

4. Flip seat forward. 5. Pull the seatback release straptoward the front seat. Make sure theseat belt buckle heads are fullyextended towards the front of thevehicle and are away from theseatback. NOTE: When the seatback release strap is pulled use your other handto guide the seatback. 6. Rotate seat...

Returning the rear seats to upright position 1. Pull seatback up and into uprightposition making sure seatback locksinto place. While holding theseatback, pull the release and pushseatback backward into the desiredposition. 2. Rotate seat cushion down into theseating position making sure thatthe sea...

To remove the rear cushion 1. Pull the Yellow tab 2. Pull the cushion to the outboardside of the vehicle. To install the rear cushion 1. Push the cushion to the inboardside of the vehicle. 2. Make sure that the hinges arelocked into place. Folding down rear bench seats (if equipped) 1. Raise the rea...

Make sure that the seat is firmly locked into position and theseat belt buckles are exposed. To remove the rear cushion 1. Pull the Yellow tab. 2. Pull the cushion so that the rodsremove from the locking tabs. To install the rear cushion 1. Push the cushion so that the rodsfit into the locking tabs....

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child from injury in a collision. All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even when an air bag (SRS) is provided. It is extreme...

movement. For example, if the driver brakes suddenly or turns a cornersharply, or the vehicle receives an impact of approximately 8 km/h (5mph) or more, the combination safety belts will lock to help reduceforward movement of the driver and passengers. Automatic locking mode In this mode, the should...

How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retractcompletely to disengage the automatic locking mode and activate thevehicle sensitive (emergency) locking mode. After any vehicle collision, the safety belt systems at all outboardseating p...

Safety belt pretensioner Your vehicle is equipped with safety belt pretensioners at the driver andfront passenger seating positions. The safety belt pretensioners are designed to activate during certainfrontal or near-frontal collisions with sufficient longitudinal deceleration.A safety belt pretens...

Shorten and fasten the belt whennot in use. Safety belt extension assembly If the safety belt is too short when fully extended, there is a 20 cm (8inch) safety belt extension assembly that can be added (part number611C22). This assembly can be obtained from your dealer at no cost. Use only extension...

If... Then... The driver’s safety belt isbuckled before the ignitionswitch is turned to the ONposition... The safety belt warning light andindicator chime remain off. BeltMinder The BeltMinder feature is a supplemental warning to the safety beltwarning function. This feature provides additional remi...

The following are reasons most often given for not wearing safety belts:(All statistics based on U.S. data) Reasons given... Consider... ⬙ Crashes are rare events ⬙ 36700 crashes occur every day. The more we drive, the more we areexposed to ⬙ rare ⬙ events, even for good drivers. 1 in 4 of us will b...

Reasons given... Consider... ⬙ The people I’m with don’t wear belts ⬙ Set the example, teen deaths occur 4times more often in vehicles withTWO or MORE people. Children andyounger brothers/sisters imitatebehavior they see. ⬙ I have an air bag ⬙ Air bags offer greater protection whenused with safety b...

• the driver’s safety belt is unbuckled • the parklamps/headlamps are in OFF position (If vehicle is equippedwith Autolamps, this will not affect the procedure.) To reduce the risk of injury, do not deactivate/activate the BeltMinder feature while driving the vehicle. 1. Turn the ignition switch to ...

Safety belt maintenance Inspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to make surethere are no nicks, tears or cuts. Replace if necessary. All safety beltassemblies, including retractors, buckles, front seat belt buckleassem...

Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries. Airbags DO NOT inflate slowly; there isa risk of injury from a deploying airbag. All occupants of the vehicle, including the driver, should a...

Do not attempt to service, repair, or modify the air bagsupplemental restraint systems or its fuses. See your Ford or Lincoln Mercury dealer. Modifications to the front end of the vehicle, including frame,bumper, front end body structure, tow hooks and B-pillar surrounding parts may affect the perfo...

How does the air bag supplemental restraint system work? The air bag SRS is designed toactivate when the vehicle sustains alongitudinal deceleration sufficientto cause the air bag sensors to closean electrical circuit that initiates airbag inflation. The fact that the airbags did not inflate in a co...

• one or more impact and safing sensors • a readiness light and tone • a diagnostic module • and the electrical wiring which connects the components The RCM (restraints control module) monitors its own internal circuitsand the supplemental air bag electrical system wiring (including theimpact sensor...

How does the side air bag system work? The side air bag system consists ofthe following: • An inflatable nylon bag (air bag)with a gas generator concealedbehind the outboard bolster ofthe driver and front passengerseatbacks. • A special seat cover designed toallow airbag deployment. • The same warni...

Several air bag systemcomponents get hot after inflation. Do not touch them afterinflation. If the side air bag has deployed, the air bag will not function again. The side air bag system (including the seat) must be inspected and serviced by a qualified technician inaccordance with the vehicle servi...

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safetyrestraints for children. Also see Air bag supplemental restraint system (SRS) in this chapter for special instructions about using air bags. Important child restraint precautions You are required by...

Child booster seats Children outgrow a typical convertible or toddler seat when they weigh40 pounds and are around 4 years of age. Although the lap/shoulder beltwill provide some protection, these children are still too small forlap/shoulder belts to fit properly, which could increase the risk of se...

Types of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has aremovable shield, remove theshield and use the lap/shoulderbelt. If a seating position has alow seat back and no headrestraint, a backless booster seatmay place...

Follow all instructions provided by the manufacturer of thebooster seat. Never put the shoulder belt under a child’s arm or behind theback because it eliminates the protection for the upper part of the body and may increase the risk of injury or death in a collision. Never use pillows, books, or tow...

8. Allow the safety belt to retract toremove any slack in the belt. 9. Before placing the child in theseat, forcibly tilt the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the seat at the belt pathand attempt to move it side to sideand forward and back. Ther...

STARTING Positions of the ignition 1. LOCK, locks the gearshift leverand allows key removal. 2. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 3. RUN, all electrical circuitsoperational and warning lights willilluminate. This is the position t...

Starting the engine 1. Turn the key to 3 (RUN) withoutturning the key to 4 (START). Ifthere is difficulty in turning the key,rotate the steering wheel until thekey turns freely. This condition mayoccur when: • the front wheels are turned • a front wheel is against the curb Turn the key to 4 (START),...

Important ventilating information If the engine is idling while the vehicle is stopped for a long period oftime, open the windows at least 2.5 cm (one inch) or adjust the heatingor air conditioning to bring in fresh air. BRAKES Occasional brake noise is normal. If a metal-to-metal, continuous grindi...

ABS warning lamp The ABS lamp in the instrumentcluster momentarily illuminateswhen the ignition is turned on. Ifthe light does not illuminate duringstart up, remains on or flashes, theABS may be disabled and may need to be serviced Even when the ABS is disabled,normal braking is still effective. (If...

4. Insert a tool (or screw driver)into the access hole to override thebrake-shift interlock. Apply thebrake and shift into Neutral whileholding down the override tab. If it is necessary to use the above procedure to move the gearshift lever,it is possible that a fuse has blown or the vehicle’s brake...

MANUAL TRANSAXLE OPERATION (IF EQUIPPED) Using the clutch Vehicles equipped with a manual transaxle have a starter interruptinterlock that prevents cranking of the engine unless the clutch pedal isdepressed. When starting a vehicle with a manual transaxle, you must: 1. Put the gearshift lever in the...

Recommended shift speeds Upshift according to the following charts for best fuel economy: Upshifts when accelerating (recommended for best fueleconomy) 1-2 22 km/h (14 mph) 2-3 40 km/h (25 mph) 3-4 55 km/h (34 mph) 4-5 70 km/h (44 mph) Upshifts when cruising (recommended for best fuel economy) 1-2 1...

Parking your vehicle 1. Apply the brake and shift into theneutral position. 2. Set the parking brake. 3. Shift into 1 (First). 1 2 4 R 3 5 1 2 4 R 3 5 2004 Escape (204) Owners Guide (post-2002-fmt)USA English (fus) Driving 130

4. Turn the ignition to position 1(LOCK) to shut the engine off andremove the ignition key. Do not park your vehicle in Neutral, it may move unexpectedlyand injure someone. Use 1 (First) gear and set the parking brake fully. CONTROL TRAC II FOUR WHEEL DRIVE (4X4) SYSTEM(IF EQUIPPED) For important in...

Using the electronic shift 4x4 system AUTO - Full power to front wheels, at all times; power to the rear wheels as required by driving conditions. Used for street and highway driving. ON - Full power to all wheels, at all times. Used for severe conditions such as deep snow, deep sand or icy roads. N...

Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any morethan low-slung sports cars are desig...

when you are driving over sand, apply the accelerator slowly and avoidspinning your wheels. If the vehicle does slide, steer in the direction ofthe slide until you regain control of the vehicle. If the transmission, transfer case or front axle are submerged in water,their fluids should be checked an...

Apply just enough power to the wheels to climb the hill. Too muchpower will cause the tires to slip, spin or lose traction, resulting in loss ofvehicle control. Descend a hill in the same gear youwould use to climb up the hill toavoid excessive brake applicationand brake overheating. Do notdescend i...

front door lock facing or door latch post pillar. Failure to follow tirepressure recommendations can adversely affect the way your vehiclehandles. Do not exceed the Ford Motor Company recommended pressureeven if it is less than the maximum pressure allowed for the tire. Each day before you drive, ch...

REVERSE SENSING SYSTEM (IF EQUIPPED) The Reverse Sensing System (RSS) sounds a tone to warn the driver ofobstacles near the rear bumper when R (Reverse) is selected and thevehicle is moving at speeds less than 5 km/h (3 mph). The system is noteffective at speeds above 5 km/h (3 mph) and may not dete...

GAWR (Gross Axle Weight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Labellocated on the driver’s door or door pillar. The total load on eachaxle must never exceed its GAWR. Exceeding th...

Exceeding the Safety Certification Label axle weight rating limitscould result in substandard vehicle handling, performance, engine, transmission and/or structural damage, serious damage to thevehicle, loss of control and personal injury. GCW (Gross Combined Weight) – is the weight of the loaded veh...

Do not use replacement tires with lower load carrying capacitiesthan the originals because they may lower the vehicle’s GVWR and GAWR limitations. Replacement tires with a higher limit than theoriginals do not increase the GVWR and GAWR limitations. Exceeding any vehicle weight rating limitation cou...

Follow these guidelines to ensure safe towing procedure: • Stay within your vehicle’s load limits. • Thoroughly prepare your vehicle for towing. Refer to Preparing to tow in this chapter. • Use extra caution when driving while trailer towing. Refer to Driving while you tow in this chapter. • Service...

4x4 GCWR (Gross Combined Weight Rating)/Trailer Weights Engine Maximum GCWR - kg (lbs.) Trailer Weight Range - kg (lbs.) Maximum frontal area of trailer - m 2 (ft) 2 2.0L w/manual transmission 1969 (4340) 453 (1000) 2.2 (24) 3.0L w/automatic transmission 2495 (5500) 907 (2000) 2.2 (24) 3.0L w/automa...

Safety chains Always connect the trailer’s safety chains to hook retainers on thevehicle. To connect the trailer’s safety chains, cross the chains under thetrailer tongue and allow slack for turning corners. If you use a rental trailer, follow the instructions that the rental agencygives to you. Do ...

Servicing after towing If you tow a trailer for long distances, your vehicle will require morefrequent service intervals. Refer to your scheduled maintenance guide formore information. Trailer towing tips • Practice turning, stopping and backing up before starting on a trip toget the feel of the veh...

RECREATIONAL TOWING An example of “recreational towing” is towing your vehicle behind amotorhome. If your vehicle is automatic transmission equipped, with a 4x2(front-wheel drive only) configured powertrain, “recreational towing” ispermitted by trailering the vehicle with its front wheels on a dolly...

GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the New Vehicle Limited...

Canadian customers who require roadside assistance, call1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford MotorCompany will reimburse a reasonable amount. To obtain reimbursementinformation, U.S. Ford or Mercury vehicles customers call1-800-241-3673; Lincoln vehicle custo...

This switch is located in the frontpassenger’s footwell, behind aflip-up cover, by the kick panelaccess cover. To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset theswitch by pushing in on the resetbutton. 4. Turn the ignition ON. 5....

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 5A Canister vent control solenoid 2 5A Blower relay (coil), Pressure switchto PCM 3 10A Rear wiper motor, Rear washermotor, Rear wiper relay (coil) 4 10A Four-wheel drive control module...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 24 15A Stoplamps, High mounted stoplamp,Trailer stoplamp, ABS unit, ASCunit (Brake Pedal Position Switch),PCM, Shift solenoid 25 30A Power window motors 26 30A Power door lock motors, GEM(door lock relay coil), Power se...

If you use the temporary spare tire continuously or do not followthese precautions, the tire could fail, causing you to lose control of the vehicle, possibly injuring yourself or others. When driving with the temporary spare tire do not: • use more than one temporary spare tire at a time • exceed 80...

Before placing the jack under the vehicle, NOTE the jack locations: • Front jacking notches are located under the front suspensionarm. • Rear jacking notches are located under the rear trailing arm. 6. Lower the jack from its storedheight to fit under the jackingnotches. Position the jack accordingt...

To stow the full size flat tire in thecargo floor, the long spare tire rodin the tool bag needs to be installed. 11. Using the lug wrench, removethe spare tire rod from the cargofloor and install the longer spare tirerod. 12. Put flat tire and tool bag withjack handle, lug nut wrench andspare tire r...

Wheel lug nut torque specifications Retighten the lug nuts to the specified torque at 800 km (500 miles)after any wheel disturbance (tire rotation, changing a flat tire, wheelremoval, etc.). Bolt size Wheel lug nut torque* Nm Lb-ft M12 x 1.5 113-153 84-114 * Torque specifications are for nut and bol...

Preparing your vehicle When the battery is disconnected or a new battery is installed, thetransmission must relearn its shift strategy. As a result, the transmissionmay have firm and/or soft shifts. This operation is considered normal andwill not affect function or durability of the transmission. Ov...

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second ...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Remove the jumper cable on the negative (...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift anddollies or flatbed equipment. Do not tow w...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handling your vehicle linewill provide warranty service, we recommend you return to your sellingdealer who wants to ensure your continued satisfaction. Pl...

In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action under the Magnuson-MossWarranty Act, or to the extent allowed by state law, before pursuingreplacement or repurchase remedies provided by certain state laws. Thisdispute handling procedure ...

Making a decision Board members review all available information related to eachcomplaint, including oral presentations, and arrive at a fair and impartialdecision. Board review may be terminated at any time by either party. Every effort is made to decide the case within 40 days of the date thatall ...

In the CAMVAP program, impartial third-party arbitrators conducthearings at mutually convenient times and places in an informalenvironment. These impartial arbitrators review the positions of theparties, make decisions and, when appropriate, render awards to resolvedisputes. CAMVAP decisions are fas...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is availablefrom your dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can discolor and s...

PAINT CHIPS Your dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jam) toyour dealer to ensure you get the correct color. • Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and in...

WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should becleaned regularly. If the wipers do not wipe properly, substances on thevehicle’s glass or the wiper blades may be the cause. These may includehot wax treatments used by commercial car washes, tree sap, or o...

INTERIOR For fabric, carpets, cloth seats, safety belts and seats equipped with sideair bags: • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Motorcraft Extra StrengthUpholstery Cleaner (ZC-41). • If grease or tar is present on the material, spot-clean the are...

FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Your Ford, Lincoln or Mercury dealer has many quality products availableto clean your vehicle and protect its finishes. These quality productshave been specifically engineered to fulfill your automotive needs; theyare custom designed to complement the styl...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a scheduled maintenance guide which makes trackingroutine service easy. If your vehicle requires professional service, your dealership can providethe...

• Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N(Neutral). 2. Block the wheels. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease h...

3.0L DOHC V6 Duratec engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Automatic transmission fluid dipstick 4. Brake fluid reservoir 5. Air filter assembly 6. Power distribution box 7. Battery 8. Engine oil dipstick 9. Engine oil filler cap 10. Windshield washer fluid reservoi...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meets Ford specifications. Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic compounds m...

6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is between the MIN—MAX marks, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough oil to raise the levelwithin the MIN—MAX range. • 2.0L DOHC I4 Zetec engine...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. However, for severe usage or in high temperature climates, check thebattery electrolyte level. Refer to the scheduled maintenance guide forthe service ...

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.Lift the battery with a battery carrier or with your hands on oppositecorners. Keep batteries out of reach of ...

If the battery has been disconnected or a new battery has been installed,the clock and the preset radio stations must be reset once the battery isreconnected. • Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “cold fill level” or within the “coldfill range” as listed on the engine coolant reservoir (depending uponapplication). • Refer to the Scheduled Maintenance Guide for service interval...

• Add Motorcraft Premium Gold Engine Coolant(yellow-colored), VC-7–A (U.S., except CA and OR), VC-7–B(CA and OR only), meeting Ford SpecificationWSS-M97B51–A1. Note: Use of Motorcraft Cooling System Stop Leak Pellets, VC-6, may darken the color of Motorcraft Premium Gold Engine Coolant fromyellow to...

2. When the engine is cool, wrap a thick cloth around the coolantpressure relief cap on the coolant reservoir (a translucent plastic bottle).Slowly turn cap counterclockwise (left) until pressure begins to release. 3. Step back while the pressure releases. 4. When you are sure that all the pressure ...

Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Refill capacities in this chapter. Fill your engine coolant reservoir as outlined in Adding engine coolant in this chapter. Severe climates If you drive in extremely cold climates (less than –36° C [–3...

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tankmay cause leakage and lead to fuel spray and fire. The fuel system may be under pressure. If the fuel filler cap isventing vapor or if you hear a hissing sound, w...

• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek medical attention. Failure to seek proper medical attention couldlead to permanent injury. • Fuels can also be harmful if absorbed through the skin. If f...

2. Carefully turn the filler cap counterclockwise 1/8 of a turn until itstops. 3. Pull to remove the cap from the fuel filler pipe. 4. To install the cap, align the tabs on the cap with the notches on thefiller pipe. 5. Turn the filler cap clockwise 1/8 of a turn until it stops. After refueling, if ...

• The indicator may come on. For more information on the “Check Engine” indicator, refer to the Instrument Cluster chapter. Fuel Filter For fuel filter replacement, see your dealer or a qualified servicetechnician. Refer to the scheduled maintenance guide for the appropriateintervals for changing th...

• Allow no more than 2 automatic click-offs when filling. • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump and have the vehicle facing thesame direction each time you fill up. • Have the vehicle lo...

• Driving on flat terrain offers improved fuel economy as compared todriving on hilly terrain. • Transmissions give their best fuel economy when operated in the topcruise gear and with steady pressure on the gas pedal. • Close windows for high speed driving. EPA window sticker Every new vehicle shou...

Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test ofthe on-board diagnostics system. If your indicator is on, refer to the description in the Warning lights and chimes section of the Instrument Cluster chapter. Your vehicle may n...

4. Check the fluid level in thereservoir. It should be between theMIN and MAX lines. Do not addfluid if the level is in this range. 5. If the fluid is low, add fluid in small amounts, continuously checkingthe level until it reaches the range between the MIN and MAX lines. Besure to put the cap back ...

High fluid level Fluid levels above the crosshatchzone may result in transaxle failure.An overfill condition of transmissionfluid may cause shift and/orengagement concerns and/orpossible damage. High fluid levels can be caused by an overheating condition. Adjusting automatic transmission fluid level...

7. Add enough fluid through the filler opening so that the fluid level is atthe bottom of the opening. 8. Install and tighten the fill plug securely. Use only fluid that meets Ford specifications. Refer to the Refill capacities in this chapter. CLUTCH FLUID (IF EQUIPPED) The clutch master cylinder a...

3. Carefully separate the two halvesof the air filter housing. 4. Remove the air filter element from the air filter housing. 5. Wipe the air filter housing and cover clean to remove any dirt ordebris and to ensure good sealing. 6. Install a new air filter element. Becareful not to crimp the filterel...

7. H: Indicates the tire’s speed rating. The speed rating denotes the speed at which a tire is designed to be driven for extended periods oftime under a standard condition of load and inflation pressure. The tireson your vehicle may operate at different conditions for load and inflationpressure. The...

Additional information contained on the tire sidewall for “LT” typetires “LT” type tires have some additionalinformation than those of “P” typetires; these differences aredescribed below: 1. LT: Indicates a tire, designated by the Tire and Rim Association(T&RA), that is intended for serviceon li...

Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask a qualified technician at a reputable repair facility to check for and correct any wheel misalignment,tire imbalance or mechanical problem involved before tire rotation. Tire wear Measure a...

Safety practices Driving habits have a great deal to do with your tire mileage and safety. • Observe posted speed limits • Avoid fast starts, stops and turns • Avoid potholes and objects on the road • Do not run over curbs or hit the tire against a curb when parking If you vehicle is stuck in snow, ...

Replace the PCV valve with one that meets Ford material anddesign specifications for your vehicle, such as a Motorcraft orequivalent replacement part. The customer warranty may be voidfor any damage to the emissions system if such a PCV valve is notused. 3 For spark plug replacement, see your dealer...

Fluid Ford PartName Application Capacity Transmissionfluid 1 Motorcraft SAE75W-90API GL-4 GearOil Manual transaxle(2WD) 2.7L (2.85quarts) 2 Manual transaxle(4X4) 2.2L (2.32quarts) 2 MotorcraftMERCON 威 ATF 2.0L engine withAutomatictransaxle and oilcooler 8.5L (9.0quarts) 3.0L engine withAutomatictran...

LUBRICANT SPECIFICATIONS Item Ford PartName orequivalent Ford PartNumber FordSpecification Body hinges,latches, doorstriker platesand rollers, seattracks, fuel fillerdoor hinge andspring, primaryand auxiliaryhood latches Multi-PurposeGrease XG-4 or XL-5 ESB-M1C93-B orESR-M1C159-A Hydraulic clutchflu...

Item Ford PartName orequivalent Ford PartNumber FordSpecification Manual transaxle 2 Motorcraft SAE75W-90 Gear Oil F32Z-19C547–MA WSS-M2C203-A1 Automatictransaxle 2 MotorcraftMERCON 威 ATF XT-2-QDX MERCON 威 Power steeringfluid MotorcraftMERCON 威 ATF XT-2-QDX MERCON 威 Rear axle (4X4) 4 Motorcraft SAE8...

Vehicle identification number (VIN) The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Please note thatin the graphic XXXX isrepresentative of your vehicleidentification number.) 1. World manufacturer identifier 2. Brake type and gross vehi...

Transmission/Transaxle code designations You can find a transmission/transaxle code on the vehicle certificationlabel which is located on the door pillar. The following table tells youwhich transmission or transaxle each code represents. Truck application: Code Transmission Description Manual transm...

Code Transmission Description Electric H One speed electric D Automatic 5–speed overdrive (5R44E) R Automatic 5–speed overdrive (5R55S) Passenger car application: Code Transmission/Transaxle Description Front wheel drive manual transaxle R 5–speed overdrive (MTX75) W 5–speed overdrive (M5) Front whe...

FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of genuine Ford accessories are available for yourvehicle through your local authorized Ford or Ford of Canada dealer.These quality accessories have been specifically engineered to fulfill yourautomotive needs; they are custom designed to complement...

A Air bag supplementalrestraint system ............97–98, 102 and child safety seats ..............99description ........................98, 102disposal ....................................104driver air bag ..................100, 103indicator light .................101, 104operation ...................

manual operation ....................128 Transmission .............................123 brake-shift interlock (BSI) ....123fluid, checking and adding(automatic) .............................217fluid, refill capacities ..............235lubricant specifications ..238, 240 Turn signal .....................