Ford 2004 Crown Victoria v.3- Manuals

SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury and prevent possibledamage to others, your vehicle and its equipment? In this guide, answersto such questions are contained in comments highlighted by the warningtriangle symbol. These comm...

SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and 6.0LPower Stroke Diesel Engine Coverage. In addition, your vehicle is eligiblefor Emissions Defect and Emissions Performance Warranties. For adetai...

Special instructions For your added safety, your vehicle is fitted with sophisticated electroniccontrols. Please read the section Supplemental restraint system (SRS) in the Seating and Safety Restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -No...

WARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lig...

misfire is occurring which could damage your catalytic converter. Drivein a moderate fashion (avoid heavy acceleration and deceleration) andhave your vehicle serviced immediately. Under engine misfire conditions, excessive exhaust temperaturescould damage the catalytic converter, the fuel system, in...

Anti-lock brake system: If the ABS light stays illuminated orcontinues to flash, a malfunction hasbeen detected, have the systemserviced immediately. Normalbraking is still functional unless the brake warning light also isilluminated. Air bag readiness: If this light fails to illuminate when ignitio...

• Optional instrument cluster Illuminates when the air suspensionis turned OFF, the load limit isexceeded or the air suspensionsystem requires servicing. Low fuel (if equipped): Illuminates when the fuel level inthe fuel tank is at or near empty(refer to Fuel gauge in this chapter for more informati...

MESSAGE CENTER INDICATOR LIGHTS (IF EQUIPPED) Speed control: This light comes on when either the SET/ACCEL orRESUME controls are pressed. Itturns off when the speed control OFF control is pressed, the brake isapplied or the ignition is turned to the OFF position. Door ajar: Illuminates when one of t...

GAUGES Standard instrument cluster gauges Optional instrument cluster gauges Speedometer: Indicates the current vehicle speed. • Standard instrument cluster MPH km/h 10 20 30 40 50 60 70 80 90 100 110 120 20 40 60 80 100 120 140 160 180 200 0 0 0 0 0 0 0 0 0 0 0 2004 Crown Victoria (cro) Owners Guid...

• Optional instrument cluster Engine coolant temperature gauge: • Standard instrument cluster • Optional instrument cluster Indicates engine coolanttemperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, theengine is over...

PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD (IF EQUIPPED) 1. Eject: Press to eject a tape. 2. Eject: Press to eject a CD. 3. Bass: Allows you to increase or decrease the audio system’s bassoutput. Press BASS then press SELto decrease or increase the bass levels. Treble: Allows you to increase or decreas...

2. Fade: Press / to shift sound to the front/rear speakers. 3. SCN (Scan): Press to hear a brief sampling of all listenable stations orCD tracks. Press again to stop. 4. CLK: To set the hour, press and hold CLK and press SEEK todecrease or increase the hours. To set the minute, press and hold CLK an...

12. Seek: Press and release SEEK / for previous/next strong station, selection or track. 13. Power/volume: Press to turn ON/OFF; turn to increase ordecrease volume levels. 14. CD : Press to enter CD mode or to play a CD already loaded into thesystem. 15. AM/FM: Press to choose a frequency band in ra...

AM/FM STEREO (IF EQUIPPED) 1. Seek: Press / to find the next strong station down/up thefrequency band. 2. Tune: Press / to manually change radio frequency down/up. 3. AM/FM: Press to choose a frequency band in radio mode. 4. Memory preset buttons: To set a station: Select frequency bandAM/FM; tune t...

4. Tape AMS: In tape mode, press and hold to activate AutomaticMusic Search (allows you to quicklylocate the beginning of the tape selection being played or to skip to thenext selection). Then, press REW (for the beginning of the currentselection) or FF (to advance to the next selection). The tape M...

3. Turn the magazine (A) over. 4. Using the disc holder releaseknob (C), pull the disc holder (B)out of the magazine. Do not pull too hard on the disc holder as the disc holder may comecompletely out of the magazine. If this happens, reinsert the disc holderback into the magazine while pressing on t...

RADIO RECEPTION FACTORS There are three factors that can affect radio reception: • Distance/strength: The further you travel from an FM station, theweaker the signal and the weaker the reception. • Terrain: Hills, mountains, tall buildings, power lines, electric fences,traffic lights and thunderstor...

CD units are designed to play commercially pressed 12 cm (4.75 in)audio compact discs only. Due to technical incompatibility, certainrecordable and re-recordable compact discs may not functioncorrectly when used in Ford CD players. Irregular shaped CDs,CDs with a scratch protection film attached, an...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in thevehicle. 2. Temperature selection: Controls the temperature of theairflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the...

To aid in side window defogging/demisting in cold weather: 1. Select NORM A/C. 2. Modulate the temperature control to maintain comfort. 3. Set the fan speed to HI. 4. Direct the outer instrument panel vents towards the side windows. To increase airflow to the outer instrument panel vents, close the ...

• Remove any snow, ice or leaves from the air intake area at the base ofthe windshield. To aid in side window defogging/demisting in cold weather: 1. Select NORM A/C. 2. Modulate the temperature control to maintain comfort. 3. Set the fan speed to HI. 4. Direct the outer instrument panel vents towar...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps,license plate lamps and tail lamps. Turns the headlamps on. Autolamp control The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the headlamp control....

Always remember to turn on your headlamps at dusk or duringinclement weather. The Daytime Running Light (DRL) System does not activate your tail lamps and generally may not provideadequate lighting during these conditions. Failure to activate yourheadlamps under these conditions may result in a coll...

Replacing headlamp bulbs To remove the headlamp bulb:1. Make sure headlamp switch is in OFF position, then open the hood.2. Remove the radiator cover by turning the three knobs to the unlockposition. 3. Disconnect the electricalconnector from the bulb by pullingrearward. 4. Remove the bulb retaining...

3. Connect the electrical connector into the rear of the plastic base untilit snaps, locking it into position. 4. Install the protective cover over headlamps locking it in place withthree knobs. 5. Turn the headlamps on and make sure they work properly. If theheadlamp was correctly aligned before yo...

Replacing tail lamp/brake/turn lamp bulbs The tail lamp, the brake lamp and the turn signal lamp bulbs are locatedin the tail lamp assembly. Follow the same steps to replace either bulb. 1. Make sure headlamp switch is inOFF position, then open the trunkand remove plastic retainer toexpose the lamp ...

Replacing high-mount brakelamp bulbs 1. Make sure headlamp switch is inOFF position, then remove twoscrews from the lamp assembly. 2. Carefully lift the lamp assemblyup for access to the bulbs. 3. Carefully pull the bulb socket outof the lamp assembly. 4. Pull the bulb straight out of thesocket and ...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick pus...

To replace the wiper blades: 1. Pull the wiper arm away from thewindshield and lock into the serviceposition. 2. Press and hold the tab on theblade and slide the blade off thewiper arm pin. 3. To attach the new wiper blade,press and hold the tab on the bladeand slide the blade on to the wiperarm pin...

OVERHEAD CONSOLE WITHOUT MOON ROOF (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according toyour option package. Some of the features in the overhead consoleinclude a compass and HomeLink 威 . To program the Homelink 威 , refer to Homelink 威 Wireless Control System it this...

Compass calibration adjustment Perform this adjustment in an openarea free from steel structures andhigh voltage lines: 1. Press and hold the MODE controluntil CAL appears in the display(approximately eight seconds) andrelease. 2. Drive the vehicle slowly (lessthan 5 km/h [3 mph]) in circles untilCA...

6. DID NOT TRAIN will be displayedif the channel did not properly train. 7. Release the channel X button.Training is complete. Note: Additional training may be required for rolling code equippeddevices. Refer to the Rolling code programming in this section. Rolling code programming To train a garage...

HomeLink 姞 default code mode HomeLink 威 uses default codes for testing and for optional home lighting accessories. To load the default codes: 1. Simultaneously press and holdbuttons 1 and 3. CLEARINGCHANNELS is displayed. 2. After 20 seconds CHANNELSCLEARED is displayed. Continue tohold the buttons....

Do not plug optional electrical accessories into the cigarette lighter. Usethe power point. Do not use the power point for operating the cigarette lighter element. The Maximum power each power point can supply depends on the fuserating. For example: a 20A fuse should supply a maximum of 240 Watts,a ...

Window lock The window lock feature allows onlythe driver to operate the powerwindows. To lock out all the window controlsexcept for the driver’s press the leftside of the control. Press the rightside to restore the window controls. POWER SIDE VIEW MIRRORS To adjust your mirrors: 1. Select to adjust...

Fold-away mirrors Pull the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash. Automatic dimming inside rear view mirror (if equipped) Your vehicle is equipped with aninside rear view mirror with anauto-dimming function. Theelectronic day/night mirror willchange ...

Never adjust the accelerator and brake pedal with feet on thepedals while the vehicle is moving. SPEED CONTROL (IF EQUIPPED) With speed control set, you can maintain a speed of 48 km/h (30 mph)or more without keeping your foot on the accelerator pedal. Speedcontrol does not work at speeds below 48 k...

STEERING WHEEL CONTROLS (IF EQUIPPED) Radio control features • Press MODE to select AM, FM1,FM2, TAPE or CD (if equipped). In Radio mode: • Press NEXT to select a presetstation from memory. In Tape mode: • Press NEXT to listen to the nextselection on the tape. In CD mode: • Press NEXT to listen to t...

• To close from the vent position, press and hold the control rearward. Do not let children play with the moon roof. They may seriouslyhurt themselves. HOMELINK 姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink 威 Wireless Control System, located on the overhead console, provides a convenient way ...

Note: There are 30 seconds in which to initiate step eight. 8. Return to the vehicle and firmly press, hold for two seconds andrelease the HomeLink 威 button. Repeat the press/hold/release sequence again, and, depending on the brand of the garage door opener (or otherrolling code equipped device), re...

Operating the HomeLink 姞 Wireless Control System To operate, simply press and releasethe appropriate HomeLink 威 button. Activation will now occur for thetrained product (garage door, gateoperator, security system, entrydoor lock, or home or office lightingetc.). For convenience, thehand-held transmi...

Select Each press of the SELECT controlwill select a different function. • Press the right side of the controlto advance the function to theright. • Press the left side of the controlto advance the function to theleft. To reset any function: 1. Push either the right or left side of the SELECT contro...

TRIP A and TRIP B These two functions allow you tosee how far you have traveled sinceyou last reset. Trip A and Trip B arecompletely independent and mustbe reset individually. To reset either trip feature to zero,press the RESET control while theappropriate trip distance feature(TRIP A or TRIP B) is...

CELL PHONE USE The use of Mobile Communications Equipment has become increasinglyimportant in the conduct of business and personal affairs. However,drivers must not compromise their own or others’ safety when usingsuch equipment. Mobile Communications can enhance personal safetyand security when app...

KEYS The vehicle is equipped with a master (black) key and valet (gray) keylock system. The master key will access doors, trunk, glove box, ignitionand remote trunk release. The valet key will access doors and ignitiononly. Before using this key, lock the trunk remote control to disable the Trunk re...

Keep vehicle doors andluggage compartment locked and keep keys and remotetransmitters out of a child’s reach.Unsupervised children could lockthemselves in the trunk and riskinjury. Children should be taughtnot to play in vehicles. On hot days, the temperature in the trunk or vehicle interior canrise...

Unlocking the doors Press this control to unlock thedriver’s door. The interior lamps willilluminate. Press the control a second timewithin five seconds to unlock alldoors. Locking the doors Press this control to lock all doors. The horn will chirp and theparklamps/taillamps will flash toconfirm the...

To replace the battery: 1. Twist a thin coin between the twohalves of the remote entrytransmitter near the key ring. DONOT TAKE THE RUBBER COVERAND CIRCUIT BOARD OFF THEFRONT HOUSING OF THEREMOTE ENTRY TRANSMITTER. 2. Do not wipe off any grease on thebattery terminals on the backsurface of the circu...

7. With the ignition still in the ON position, press the unlock controlonce. After a five to ten second delay, the door will lock/unlock toconfirm successful programming. 8. After having waited the necessary time for the programming toconfirm, turn the ignition to OFF. Once disabled, the autolock fe...

4. Press 1 • 2 to store the first personal code. 5. The doors will lock then unlock to confirm programming of the newcode. To store a second personal code: 1. Enter the factory set code. 2. Within five seconds press 1 • 2 on the keypad to enter the programming mode. 3. Enter a second personal 5-digi...

Unlocking the doors and releasing the trunk with the keyless entrysystem To unlock the driver door, enter either the factory-set code or personalcode (each digit pressed within 5 seconds of prior digit). The interiorlamps will illuminate. • To unlock all doors, enter the factory-set code or personal...

Automatic arming The vehicle is armed immediatelyafter switching the ignition to the 3(OFF) or 2 (LOCK) position. Theindicator on the instrument panelwill flash every two seconds whenthe vehicle is armed. Automatic disarming Switching the ignition to the 4 (ON) position with a coded key disarms the ...

If your keys are lost or stolen you will need to do the following: • Use your spare key to start the vehicle, or • Have your vehicle towed to a dealership or a locksmith. The key codeswill need to be erased from your vehicle and new key codes will needto be re-coded. Replacing coded keys can be very...

4. Turn the ignition to 3 (OFF) then 2 (LOCK) and remove the second coded key from the ignition. 5. Within twenty seconds of removing the second coded key, insert the new unprogrammed key (new key) into the ignition and turn the ignitionfrom 3 (OFF) to 4 (ON) (maintain ignition in 4 (ON) for at leas...

SEATING Adjustable head restraints Your vehicle’s seats are equipped with head restraints which arevertically adjustable. The purpose of these head restraints is to help limithead motion in the event of a rear collision. To properly adjust your headrestraints, lift the head restraint so that it is l...

To adjust the front seatback usingthe manual recliner: • Lift and hold the handle locatedon the side of the seat. • Lean against the seatback toadjust it to your desired position.You can recline the seat back orbring it forward. • Release the handle when the desired position has been reached. Using ...

Adjusting the power front seats – door mounted controls(if equipped) The controls for the power seats are located on the inside of each frontdoor. Never adjust the driver’s seat or seatback when the vehicle ismoving. Do not pile cargo higher than the seatbacks to avoid injuringpeople in a collision ...

safety belt pretensioners, front safety belt buckle sensors, and the driverseat position sensor. In addition, the RCM also monitors the restraintswarning light in the instrument cluster. A difficulty with the system isindicated by one or more of the following. • The warning light will either flash o...

In a rollover crash, an unbelted person is significantly more likelyto die than a person wearing a safety belt. Each seating position in your vehicle has a specific safety beltassembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on t...

2. To unfasten, push the releasebutton and remove the tongue fromthe buckle. Energy management feature • This vehicle has a seat belt system with an energy managementfeature at the front outboard seating positions to help further reducethe risk of injury in the event of a head-on collision. • This s...

When to use the automatic locking mode • Any time a child safety seat is installed in a passenger front outboard or any rear seating position. Children 12 years old and under shouldbe properly restrained in the rear seat whenever possible. Refer to Safety Restraints for Children or Safety Seats for ...

How to disengage the automatic locking mode Ford Motor Company recommends that all passenger safety beltassemblies and attaching hardware should be inspected by a qualified technician after any collision to verify that the ⬙ automatic locking retractor ⬙ feature for child seats is still working prop...

Lap belts Adjusting the front center seat lap belt The lap belt should fit snugly and as low as possible around thehips, not across the waist. The lap belt does not adjustautomatically. Insert the tongue intothe correct buckle (the buckleclosest to the direction the tongue iscoming from). To lengthe...

If... Then... The driver’s safety belt isbuckled before the ignitionswitch is turned to the ONposition... The BeltMinder feature will notactivate. The following are reasons most often given for not wearing safety belts:(All statistics based on U.S. data) Reasons given... Consider... “Crashes are rar...

Reasons given... Consider... “The people I’m with don’twear belts” Set the example, teen deaths occur 4times more often in vehicles withTWO or MORE people. Children andyounger brothers/sisters imitatebehavior they see. “I have an air bag” Air bags offer greater protection whenused with safety belts....

Safety belt extension assembly If the safety belt is too short when fully extended, there is a 20 cm(8 inch) safety belt extension assembly that can be added (part number611C22). This assembly can be obtained from your dealer at no cost. Use only extensions manufactured by the same supplier as the s...

AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries. Airbags DO NOT inflate slowly; there isa risk of injury from a deploying airbag. All occupants of...

Children and air bags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. Air bags can...

If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in acollision. If the safety belt pretensioners deploy in an accident, they willnot function again ( belt will not e...

The side air bags are fitted on the outboard side of the seatbacks of thefront seats. In certain lateral collisions, the air bag on the side affectedby the collision will be inflated. The air bag was designed to inflatebetween the door panel and occupant to further enhance the protectionprovided occ...

• The readiness light will not illuminate immediately after ignition isturned on. • A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and/or light are repaired. If any of these things happen, even intermittently, have the SRS servicedat your dealership ...

Follow all the important safety restraint and air bag precautions thatapply to adult passengers in your vehicle. If the shoulder belt portion of a combination lap and shoulder belt canbe positioned so it does not cross or rest in front of the child’s face orneck, the child should wear the lap and sh...

• Is the shoulder belt centered on the shoulder and chest? • Can the child stay seated like this for the whole trip? Types of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has aremovable shield, remove theshield and use ...

never use a booster seat with a lap belt only. It is best to use a boosterseat with lap/shoulder belts in the back seat- the safest place for childrento ride. Follow all instructions provided by the manufacturer of thebooster seat. Never put the shoulder belt under a child’s arm or behind theback be...

8. Allow the safety belt to retract toremove any slack in the belt. 9. Before placing the child in theseat, forcibly move the seat forwardand back to make sure the seat issecurely held in place. To checkthis, grab the seat at the belt pathand attempt to move it side to sideand forward. There should ...

2. Route the child safety seat tether strap over the back of the seat. For vehicles with adjustable head restraints, route the tether strap underthe head restraint and between the head restraint posts, otherwise routethe tether strap over the top of the seatback. 3. Locate the correct anchor for the...

STARTING Positions of the ignition 1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 2. LOCK, locks steering wheel(police vehicles only), the automatictransmission gearshift lever andallows key removal. 3. OFF, shuts off the engine and allacce...

Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate. Starting the engine 1. Turn the key to 4 (ON) withoutturning the key to 5 (START). 2. Turn the key t...

To reduce the risk of electrical shock, do not use your heaterwith ungrounded electrical systems or two-pronged (cheater) adapters. Guarding against exhaust fumes Carbon monoxide is present in exhaust fumes. Take precautions to avoidits dangerous effects. If you smell exhaust fumes inside your vehic...

The parking brake is not recommended to stop a moving vehicle.However, if the normal brakes fail, the parking brake can be used to stopyour vehicle in an emergency. Since the parking brake applies only therear brakes, the vehicle’s stopping distance will increase greatly and thehandling of your vehi...

Aggressive driving in any road conditions can cause you to losecontrol of your vehicle increasing the risk of severe personal injury or property damage. The occurrence of an Traction Control 娂 event is an indication that at least some of the tires have exceededtheir ability to grip the road; this ma...

It is also important to maintain a proper power steering fluid level in thepower steering fluid reservoir: • Do not operate the vehicle with a low power steering pump fluid level(below the MIN mark on the reservoir). • Some noise is normal during operation. If the noise is excessive, checkfor low po...

This system keeps the rear of your vehicle at a constant level byautomatically adding air or releasing air from the springs.If you exceed the load limit, the rear air suspension may not operate. The air suspension shut-off switch islocated on the left side of the trunk.If this switch is in the OFF p...

Do not drive your vehicle until you verify that the brakelampsare working. Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle. If the parking brake is fully released, but the ...

• Optional instrument cluster Drive (not shown) Drive is activated when the transmission control switch is pressed. • This position allows for all forward gears except overdrive. • O/D OFF lamp is illuminated. • Provides engine braking. • Use when driving conditions cause excessive shifting from O/D...

If your vehicle gets stuck in mud or snow If your vehicle gets stuck in mud or snow, it may be rocked out byshifting from forward and reverse gears, stopping between shifts in asteady pattern. Press lightly on the accelerator in each gear. Do not rock the vehicle if the engine is not at normal opera...

VEHICLE LOADING – WITH AND WITHOUT A TRAILER This section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehicle weight within its design ratingcapability, with or without a trailer. Properly loading your vehicle willprovide maximum return of vehicle design p...

GCWR (Gross Combined Weight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo andpassengers – that the vehicle can handle without risking damage.(Important: The towing vehicle’s braking system is rated for operation atGVWR, not at GCWR. Separate fu...

Trailer lamps Trailer lamps are required on most towed vehicles. Make sure all runninglights, brake lights, turn signals and hazard lights are working. See yourdealer or trailer rental agency for proper instructions and equipment forhooking up trailer lamps. Driving while you tow When towing a trail...

Launching or retrieving a boat Disconnect the wiring to the trailer before backing the trailerinto the water. Reconnect the wiring to the trailer after thetrailer is removed from the water. When backing down a ramp during boat launching or retrieval: • do not allow the static water level to rise abo...

GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the New Vehicle Limited...

The fuel pump shut-off switch islocated on the left side of the trunkbehind the left rear tail light and thetrunk liner. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, r...

Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wiredamage and could start a fire. Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link ca...

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 15A Audio, CD changer 2 5A Audio (optional) 3 7.5A Mirrors 4 10A Air bags 5 25A Package tray lamps and rearflasher lamps (Police vehicleoptions) 6 15A Instrument cluster warning lampsmo...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 8 25A Powertrain Control Module (PCM)power relay, Coil-on plugs, Radionoise capacitor, Passive Anti-TheftSystem (PATS) 9 5A Transmission range sensor 10 10A Rear window defrost, Heatedmirrors 11 5A Traction control indi...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 21 15A LCM for park lamps and interiorillumination, Autolamp/Sunloadsensor 22 20A Speed control servo,Multi-function switch for hazardlamps, Brake on/off switch, Feedfor IP fuse 19 23 15A EATC module, Instrument cluster...

• Use more than one T-type/mini spare tire at a time • Use commercial car washing equipment • Try to repair the T-type/mini spare tire Use of a T-type/mini spare tire at any one wheel location can lead toimpairment of the following: • Handling, stability and braking performance • Comfort and noise •...

• Winter weather driving capability • Wet weather driving capability • All-Wheel Driving Capability (if applicable) • Load Leveling Adjustment (if applicable) When driving with the dissimilar spare tire/wheel additional cautionshould be given to: • Towing a trailer • Driving vehicles equipped with a...

• Position the jack according to thefollowing guides and turn the jackhandle clockwise until the wheelis completely off the ground. To lessen risk of personalinjury, do not put any part of your body under the vehiclewhile changing a tire. Do not startthe engine when your vehicle ison the jack. The j...

12. Remove the jack and fullytighten the lug nuts in the ordershown. Refer to Wheel lug nut torque specifications later in this chapter for the proper lug nuttorque specification. 13. Put flat tire, jack and lug wrenchaway. 14. Turn on the air suspensionswitch (if equipped). Wheel lug nut torque spe...

Preparing your vehicle When the battery is disconnected or a new battery is installed, thetransmission must relearn its shift strategy. As a result, the transmissionmay have firm and/or soft shifts. This operation is considered normal andwill not affect function or durability of the transmission. Ov...

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second ...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Remove the jumper cable on the negative (...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home You must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handling your vehicle linewill provide warranty service, we recommend you return to your sellingdealer who wants to ensure your continued satisfaction. Pl...

In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action under the Magnuson-MossWarranty Act, or to the extent allowed by state law, before pursuingreplacement or repurchase remedies provided by certain state laws. Thisdispute handling procedure ...

Every effort is made to decide the case within 40 days of the date thatall requested information is received by the Board. Since the Boardgenerally meets once a month, it may take longer for the Board toconsider some cases. After a case is reviewed, the Board mails you a decision letter and aform on...

parties, make decisions and, when appropriate, render awards to resolvedisputes. CAMVAP decisions are fast, fair, and final; the arbitrator’saward is binding both to you and Ford of Canada. CAMVAP services are available in all territories and provinces. For moreinformation, without charge or obligat...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is availablefrom your dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can discolor and s...

• Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and industrial fallout before repairing paint chips. • Always read the instructions before using the products. ALUMINUM WHEELS AND WHEEL COVERS Aluminum wheels and wheel covers are coated with a clearcoat paint...

• Cover the highlighted areas to prevent water damage when cleaningthe engine. • Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailab...

• Do not use fuel, kerosene, or paint thinner to clean any parts. • Wiper blades can be cleaned with isopropyl (rubbing) alcohol orwindshield washer solution. Be sure to replace wiper blades when theyappear worn or do not function properly. Do not use sharp objects, such as a razor blade, to clean t...

Do not use cleaning solvents, bleach or dye on the vehicle’ssafety belts, as these actions may weaken the belt webbing. Do not use chemical solvents or strong detergents when cleaningthe seat-mounted side air bag. Such products could contaminate the side air bag system and affect performance of the ...

FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Your Ford, Lincoln or Mercury dealer has many quality products availableto clean your vehicle and protect its finishes. These quality productshave been specifically engineered to fulfill your automotive needs; theyare custom designed to complement the styl...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a scheduled maintenance guide which makes trackingroutine service easy. If your vehicle requires professional service, your dealership can providethe...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under theinstrument panel. 2. Go to the front of the vehicle andrelease the auxiliary latch that islocated under the front of the hood. 3. Lift the hood until the liftcylinders hold it open. 2004 Crown Victoria (cro) Owners ...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.6L SOHC V8 engine 1. Brake fluid reservoir 2. Engine oil dipstick 3. Windshield washer fluid reservoir 4. Air filter assembly 5. Power steering fluid reservoir 6. Engine coolant reservoir 7. Battery 8. Engine oil filler cap 9. Automatic transmission...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16–A2.Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic c...

5. Locate and carefully remove theengine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added...

• If required, add engine oil to theengine. Refer to Adding engine oil in this chapter. • Do not overfill the enginewith oil. Oil levels above thismark may cause enginedamage. If the engine is overfilled, some oil must beremoved from the engine by aqualified service technician. 7. Put the indicator ...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. However, for severe usage or in high temperature climates, check thebattery electrolyte level. Refer to the Scheduled Maintenance Guide for the service...

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.Lift the battery with a battery carrier or with your hands on oppositecorners. Keep batteries out of reach of ...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant sho...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “FULL COLD” level or within the“COLD FILL RANGE” as listed on the engine coolant reservoir(depending upon application). • Refer to the Scheduled Maintenance Guide for service interval...

Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine...

remove the coolant pressure relief cap on the radiator of a vehicle withan overflow system, follow these steps to add engine coolant. To reduce the risk of personal injury, make sure the engine iscool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and ...

Used engine coolant should be disposed of in an appropriate manner. Follow your community’s regulations and standards for recyclingand disposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Refill capacities in this section....

What you should know about fail-safe cooling If the engine coolant supply is depleted, this feature allows the vehicle tobe driven temporarily before incremental component damage is incurred.The “fail-safe” distance depends on ambient temperatures, vehicle loadand terrain. How fail-safe cooling work...

• The air conditioning system will be disabled. Continued operation will increase the engine temperature: • If your vehicle is equipped with digital gauges, the gauge bars willflash and a tone will sound every five seconds for one minute. • The engine will completely shut down, causing steering and ...

splashed on the skin, promptly wash skin thoroughly with soap andwater. Consult a physician immediately if you experience an adversereaction. When refueling always shut the engine off and never allowsparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely haza...

• Your “Check Engine” indicator may come on. For more information onthe “Check Engine” indicator, refer to the Instrument Cluster chapter. Fuel Filter For fuel filter replacement, see your dealer or a qualified servicetechnician. Refer to the scheduled maintenance guide for the appropriateintervals ...

• Use the same filling rate setting (low — medium — high) each timethe tank is filled. • Allow no more than 2 automatic click-offs when filling. • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump and...

2. While the engine idles, turn the steering wheel left and right severaltimes. 3. Turn the engine off. 4. Check the fluid level in thereservoir. It should be between theMIN and MAX lines. Do not addfluid if the level is in this range. 5. If the fluid is low, add fluid in small amounts, continuously...

If an overfill occurs, excess fluidshould be removed by a qualifiedtechnician. An overfill condition oftransmission fluid may causeshift and/or engagementconcerns and/or possibledamage. Do not use supplemental transmission fluid additives, treatments orcleaning agents. The use of these materials may...

Note: Failure to use the correct air filter element may result in severe engine damage. The customer warranty may be voided for any damage tothe engine if the correct air filter element is not used. INFORMATION ABOUT UNIFORM TIRE QUALITY GRADING New vehicles are fitted with tiresthat have a rating o...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing thetire’s resistance to the gene...

3. 65: Indicates the aspect ratio which gives the tire’s ratio of height to width. 4. R: Indicates a “radial” type tire. 5. 15: Indicates the wheel or rim diameter in inches. If you change your wheel size, you will have to purchase new tires to match the new wheeldiameter. 6. 95: Indicates the tire’...

located on the structure by the trailing edge of the driver’s door or theedge of the driver’s door. The cold inflation pressure should never be setlower than the recommended pressure on the vehicle label. The tire suppliers may have additional markings, notes or warnings suchas standard load, radial...

Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask a qualified technician at a Ford or Lincoln/Mercury dealership to check for and correct any wheelmisalignment, tire imbalance or mechanical problem involved before tirerotation. Note: Your ...

Tire explosions can cause death, personal injury or propertydamage. Do not allow anyone to stand near, directly ahead or behind the spinning tire. Never spin the tires in excess of the 35 mph (55 km/h) pointindicated on the speedometer. Highway hazards No matter how carefully you drive there’s alway...

REFILL CAPACITIES Fluid Ford Part Name Capacity Engine oil (includesfilter change) 6 Motorcraft SAE 5W-20Premium SyntheticBlend Motor Oil (US)Motorcraft SAE 5W-20Super Premium MotorOil (Canada) 5.7L (6.0 quarts) Brake fluid Motorcraft HighPerformance DOT 3Motor Vehicle BrakeFluid 1 Fill to line on r...

3 Indicates only approximate dry-fill capacity. Some applications may vary based on cooler size and if equipped with an in-tank cooler. The amountof transmission fluid and fluid level should be set by the indication onthe dipstick’s normal operating range. Police or Handling Package refillcapacity-1...

Item Ford partname Ford partnumber Fordspecification Engine oil Motorcraft SAE5W-20 PremiumSynthetic BlendMotor Oil (US)Motorcraft SAE5W-20 SuperPremium MotorOil (Canada) XO-5W20-QSP(US)CXO-5W20–LSP12(Canada) WSS-M2C153-Hwith APICertificationMark Hinges, latches,striker plates,fuel filler doorhinge ...

2 Add 118 ml (4 oz.) of Additive Friction Modifier XL-3 or equivalent meeting Ford specification EST-M2C118-A for complete refill ofTraction-Lok rear axles. 3 Ensure the correct automatic transmission fluid is used. Transmission fluid requirements are indicated on the dipstick or on the dipstickhand...

IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedto a vehicle and prescribe where theCertification label may be located.The Certification label is located onthe front door latch pillar on thedriver’...

Engine number The engine number (the last eight numbers of the vehicle identificationnumber) is stamped on the engine block, transmission, frame andtransfer case (if equipped). Transmission/Transaxle code designations You can find a transmission/transaxle code on the vehicle certificationlabel which...

Code Transmission Description E Automatic 4–speed overdrive (4R100) J Automatic 5–speed overdrive (5R55E) Electric H One speed electric D Automatic 5–speed overdrive (5R44E) R Automatic 5–speed overdrive (5R55S) Passenger car application: Code Transmission/Transaxle Description Front wheel drive man...

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for yourvehicle through your local authorized Ford or Ford of Canada dealer.These quality accessories have been specifically engineered to fulfill yourautomotive needs; they are custom designed to co...

A ABS (see Brakes) .....................129 Air bag supplementalrestraint system ................105, 109 and child safety seats ............107description ......................105, 109disposal ....................................112driver air bag ..................107, 110indicator light ............

Transmission .............................134 brake-shift interlock (BSI) ....134fluid, checking and adding(automatic) .............................209fluid, refill capacities ..............227lubricant specifications ..228, 230 Trunk ...........................................74 remote release .......