Ford 2003 Ranger v.2- Manuals

SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and 7.3LPower Stroke Diesel Engine Coverage. In addition, your vehicle is eligiblefor Emissions Defect and Emissions Performance Warranties. For adetai...

Special instructions For your added safety, your vehicle is fitted with sophisticated electroniccontrols. Please read the section Supplemental Restraint System (SRS) in the Seating and safety restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury...

Using your vehicle as an ambulance Do not use this vehicle as an ambulance. Your vehicle is not equipped with the Ford Ambulance PreparationPackage. Electric vehicles For specific information regarding the operation of your electric vehicle,refer to the Electric Vehicle Owner’s Guide Supplement. Mid...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -No...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

Brake system warning light: To confirm the brake system warninglight is functional, it willmomentarily illuminate when theignition is turned to the ON positionwhen the engine is not running, or in a position between ON and START,or by applying the parking brake when the ignition is turned to the ONp...

Check gage: Illuminates when any of the following conditions hasoccurred: • The engine coolant temperatureis high. • The engine oil pressure is low. • The fuel gauge is at or near empty. Door ajar: Illuminates when the ignition is in the ON position andany door is open. Overdrive off (if equipped): ...

Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, the engine is overheating. Stopthe vehicle as soon as safelypossible, switch off the engineand let the engi...

Battery voltage gauge: Indicates the battery voltage when theignition is in the ON position. If thepointer moves and stays outside thenormal operating range (asindicated by arrows), have thevehicle’s electrical system checkedas soon as possible. Engine oil pressure gauge: Indicates engine oil pressu...

AM/FM STEREO 1. Seek: Press / to find the next strong station down/up thefrequency band. 2. Tune: Press / to manually change radio frequency down/up. 3. AM/FM: Press to choose a frequency band in radio mode. 1 2 3 4 AM/FM SEEK TONE CLK TUNE TONE VOL 12 FM ST DX VOL PUSH ON 5 3 6 7 4 1 2 AM/FM Entert...

4. Memory preset buttons: To set a station: Select frequency bandAM/FM; tune to a station, press andhold a preset button until sound returns. 5. Power/volume: Press to turn ON/OFF; turn to increase ordecrease volume levels. 6. Tone: Press TONE until the desired level — Bass, Treble, Fadeappears on t...

5. EJ (eject): Press to eject a CD. 6. COMP (Compression): In CD mode, press to bring louder andsofter levels into more comfortablelistening level. The compression icon (c) will appear in the display. 7. Shuffle: Press to listen to the tracks on the CD in random order.Press again to turn off. 8. Mem...

15. AM/FM: Press to choose a frequency band in radio mode. 16. Bass: Press / to increase/decrease the bass output. 17. Treble: Press / to increase/decrease the treble output. 18. CD door: Insert a CD printed side up. PREMIUM IN-DASH SIX CD SOUND SYSTEM 1. Seek: Press and release SEEK / for previous/...

2. Rewind: Press for a slow rewind, press and hold for a fast rewind. Fast forward: Press for a slow advance, press and hold for a fastadvance. 3. Comp (Compression): In CD mode, press to adjust the soft and loud passages together for a more consistent listening level. Press the COMPcontrol until CO...

Traffic: Allows you to hear traffic broadcasts. With the feature ON, press SEEK or SCAN to find a station broadcasting a traffic report (if it isbroadcasting RDS data). Traffic information is not available in most U.S. markets. FIND Program type: Allows you to search RDS-equipped stations for a cert...

17. Power/volume: Press to turn ON/OFF; turn to increase ordecrease volume levels. 18. CD: Press CD to play a CD or MP3 disc. When the MP3 disc isloaded, CD and LOAD will appearon the display. The display willbriefly show the total number of tracks on the disc as TXXX(XXX=number of tracks). 19. AM/F...

SAMPLE HIERARCHIES If you are burning your own MP3discs, it is important to understandhow the MACH 威 MP3 music system will read the hierarchies you create.This is an example of creating adirectory structure that is one leveldeep with various types of music.While various files are present, (fileswith...

TREMOR AUDIO SYSTEM 1. MUTE: Press to mute the playing media. Press again to return to theplaying media. 2. TAPE: Insert the cassette with the opening to the right. If a tape isalready inserted into the system,press TAPE to being tape play. 3. CD: Insert a CD label side up. If a CD is already insert...

16. EJ (Eject): Press to eject a CD. RADIO FREQUENCIES AM and FM frequencies are established by the Federal CommunicationsCommission (FCC) and the Canadian Radio and TelecommunicationsCommission (CRTC). Those frequencies are: AM - 530, 540–1700, 1710 kHz FM- 87.7, 87.9–107.7, 107.9 MHz RADIO RECEPTI...

CD/CD PLAYER CARE Do: • Handle discs by their edges only. Never touch the playing surface. • Inspect discs before playing. Clean only with an approved CD cleanerand wipe from the center out. Don’t: • Expose discs to direct sunlight or heat sources for extended periodsof time. • Insert more than one ...

HEATER ONLY SYSTEM(IF EQUIPPED) 1. Fan speed adjustment: Controls the volume of air circulated in thevehicle. 2. Temperature selection: Controls the temperature of theairflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief d...

OPERATING TIPS • To reduce fog build up on the windshield during humid weather, placethe air flow selector in the position. • To reduce humidity build up inside the vehicle: do not drive with theair flow selector in the OFF or MAX A/C position. • Under normal weather conditions, do not leave the air...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps,license plate lamps and tail lamps. Turns the headlamps on. Foglamp control (if equipped) The foglamps can be turned onwhen the headlamp control is ineither of the following positions: • Parking lamps • Low beam...

High beams Push the lever toward theinstrument panel to activate. Pullthe lever towards you to deactivate. Flash to pass Pull toward you slightly to activateand release to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of theinstrument panel and all applicableswitches in the vehicle d...

Replacing headlamp bulbs To remove the headlamp bulb: 1. Turn the headlamp switch is inthe OFF position, then open thehood. 2. Remove two screws and cover(if equipped). 3. At the back of the headlamp, pryup the two retainer pins to releasethe headlamp assembly from thevehicle and pull headlamp forwa...

Replacing tail lamp/backup lamp bulbs 1. Open the tailgate to expose thelamp assemblies. 2. Remove the four screws and thelamp assembly from vehicle. 3. Rotate bulb socketcounterclockwise turn and removefrom lamp assembly. 4. Carefully pull the bulb straightout of the socket Install the new bulb(s) ...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Windshield washer: Push the end of the stalk: • briefly: causes a single swipe ofthe wipers without washer fluid. • a quick pus...

TILT STEERING WHEEL (IF EQUIPPED) To adjust the steering wheel: 1. Pull and hold the steering wheelrelease control toward you. 2. Move the steering wheel up ordown until you find the desiredlocation. 3. Release the steering wheelrelease control. This will lock thesteering wheel in position. Never ad...

POWER WINDOWS (IF EQUIPPED) When closing the powerwindows, you should verify they are free of obstructions andensure that children and/or petsare not in the proximity of thewindow openings. Press and hold the bottom part of the rocker switch to open the window.Press and hold the top part of the rock...

SPEED CONTROL (IF EQUIPPED) With speed control set, you canmaintain a speed of 48 km/h(30 mph) or more without keepingyour foot on the accelerator pedal.Speed control does not work atspeeds below 48 km/h (30 mph). Do not use the speedcontrol in heavy traffic or on roads that are winding, slipperyor ...

CENTER CONSOLE (IF EQUIPPED) Your vehicle may be equipped with avariety of console features. Theseinclude: • Utility compartment withcassette/compact disc storage • Cupholders • Coin holder slots • Flip up armrest Use only soft cups in the cupholder. Hard objects can injure youin a collision. Cell p...

Do not drive with front panelunlocked or folded on top of therear panel. To stow the rear panel: • Before driving with the tonneaucover open, stow the rear panel. • Disconnect the hydrauliccylinders from the ball stud onthe pickup box and secure themin the clips on the tonneau cover. • Lift the rear...

KEYS The key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer. You should always carry a second key with you in a safe place in caseyou require it in an emergency. Refer to SecuriLock 娂 Passive Anti-Theft System for more information. POWER DOOR LOCK...

• unlock the vehicle doors withouta key. • lock all the vehicle doors withouta key. • activate the personal alarm. If there is any potential remote keyless entry problem with your vehicle,ensure ALL remote entry transmitters are taken to the dealership, to aid in troubleshooting. Unlocking the doors...

• 20 seconds elapse after all vehicle doors are closed and locked usingthe remote entry transmitter, or the power door unlock control (whilethe accompanying door is open). The UNLOCK feature will work again after: • a door has become ajar, • the ignition is turned to the ON position, or • using the ...

To replace the battery: 1. Twist a thin coin between the twohalves of the remote entrytransmitter near the key ring. DONOT TAKE THE FRONT PART OFTHE REMOTE ENTRYTRANSMITTER APART. 2. Remove the old battery. 3. Insert the new battery. Refer tothe diagram inside the remote entrytransmitter for the cor...

6. Within 20 seconds press any button on the remote entry transmitter. Note: If more than 20 seconds have passed you will need to start the procedure over again. 7. The doors will lock, then unlock, to confirm that this remote entrytransmitter has been programmed. 8. Repeat Step 6 to program each ad...

Note: The SecuriLock 娂 passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems mayresult in vehicle starting problems and a loss of security protection. Note: Large metallic objects, electronic devices that are used to purchase gasoline or sim...

Automatic disarming Switching the ignition to the 4 (ON) position with a coded key disarms the vehicle. • The THEFT indicator will illuminate for three seconds and then go out. • If the THEFT indicator stays on for an extended period of time or flashes rapidly, have the system serviced by your deale...

1. Insert a previously programmedcoded key into the ignition. 2. Turn the ignition from the 3(OFF) position to the 4 (ON)position. Keep the ignition in the 4(ON) position for at least onesecond, but no more than 10seconds. 3. Turn the ignition to the 3 (OFF)position, and remove the coded keyfrom the...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Adjusting the front manual seat ...

Using the manual lumbar support (if equipped) Turn the lumbar support controlclockwise to increase firmness. Turn the lumbar support controlcounterclockwise to increasesoftness. Passenger side rear access (if equipped) Pull up on the recliner handle. Theseat will lean forward and unlockthe track. Sl...

Center facing jump seat (4 door SuperCab) (if equipped) To open, pull seat assembly down,then raise seatback. To stow the seat, fold seat backdown and raise seat assembly to thefully upright position. Do not install a child seat ina center facing jump seat. Booster seats must beinstalled only in sea...

It is extremely dangerous to ride in a cargo area, inside oroutside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people toride in any area of your vehicle that is not equipped with seats andsafety belts. Be sure everyone i...

2. To unfasten, push the releasebutton and remove the tongue fromthe buckle. The front outboard safety restraints in the vehicle are combination lapand shoulder belts. The front passenger outboard safety belt has twotypes of locking modes described below: Vehicle sensitive mode This is the normal re...

BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED ifthe safety belt assembly “automatic locking retractor” feature or any other safety belt function is not operating properly when checkedaccording to the procedures in Workshop Manual. Failure to replace the Belt and Retractor assembly couldincrease the r...

• Regular Cab and 4–door SuperCab • 2–door SuperCab To lower the shoulder belt height, push the button and slide the heightadjuster down. To raise the height of the shoulder belt, slide the heightadjuster up. Pull down on the height adjuster to make sure it is locked inplace. Position the safety bel...

Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a right angle to the beltand pull across your lap until itreaches the buckle. To tighten thebelt, pull the loose end of the beltthrough the tongue until it ...

Safety belt extension assembly If the safety belt is too short when fully extended, there is a 20 cm (8inch) safety belt extension assembly that can be added (part number611C22). This assembly can be obtained from your dealer at no cost. Use only extensions manufactured by the same supplier as the s...

One time disable Any time the safety belt is buckled and then unbuckled during anignition ON cycle, the BeltMinder will be disabled for that ignition cycleonly. Deactivating/activating the BeltMinder feature Read steps 1 - 9 thoroughly before proceeding with thedeactivation/activation programming pr...

Failure to inspect and if necessary replace the safety beltassembly under the above conditions could result in severe personal injuries in the event of a collision. Refer to Interior in the Cleaning chapter. AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Important supplemental restraint system (SRS) pr...

Never place your arm over the air bag module as a deploying airbag can result in serious arm fractures or other injuries. Never place a rear facing infant seat in the front seat unless thepassenger air bag is turned off. Steps you can take to properly position yourself away from the airbag: • Move y...

Children and air bags For additional important safety information, read all information onsafety restraints in this guide. Never place a rearwardfacing child safety restraint in front of an airbag. Airbags havebeen known to kill or injurechildren in front facing childsafety restraints. Wheneverplaci...

An air bag can kill or injure a child in a child seat. Child seatsshould never be placed in the front seats, unless passenger air bag switch is turned off. See Passenger air bag on/off switch in this chapter. Rear facing child seats should NEVER be placed in the frontseats unless the passenger airba...

The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion ...

The RCM (restraints control module) monitors its own internal circuitsand the supplemental air bag electrical system warning (including thepassenger air bag deactivation switch, the impact sensors, the systemwiring, the air bag system readiness light, the air bag back up power andthe air bag ignitor...

Passenger air bag ON/OFF switch An air bag ON/OFF switchhas been installed in this vehicle. Before driving, always look at the face of the switch tobe sure the switch is in the properposition in accordance with theseinstructions and warnings. Failureto put the switch in a properposition can increase...

injuries, air bags must open with great force, and this force can pose apotentially deadly risk in some situations, particularly when a front seatoccupant is not properly buckled up. The most effective way to reducethe risk of unnecessary air bag injuries without reducing the overallsafety of the ve...

This vehicle has special energy management safety belts for thedriver and/or right front passenger. These particular belts are specifically designed to work with air bags to help reduce the risk ofinjury in a collision. The energy management safety belt is designed togive or release additional belt ...

This vehicle has special energy management safety belts for thedriver and/or right front passenger. These particular belts are specifically designed to work with air bags to help reduce the risk ofinjury in a collision. The energy management safety belt is designed togive or release additional belt ...

Follow all the important safety restraint and air bag precautions thatapply to adult passengers in your vehicle. If the shoulder belt portion of a combination lap and shoulder belt canbe positioned so it does not cross or rest in front of the child’s face orneck, the child should wear the lap and sh...

The importance of shoulder belts Using a booster without a shoulder belt increases the risk of a child’shead hitting a hard surface in a collision. For this reason, you shouldnever use a booster seat with a lap belt only. It is best to use a boosterseat with lap/shoulder belts in the back seat- the ...

Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all of the manufacturer’s instructions with thesafety seat you put in your vehicle. If you do not install and use thesafety seat properly, the child may be injured in a ...

7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with knee on thechild seat. 8. Allow the safety belt to retract toremove any slack in the belt. 9. Before placing the child in theseat, forcibly tilt the seat forwardand back to make...

• Bucket seats • 60/40 seats Attach the tether strap only to the appropriate tether anchor asshown. The tether strap may not work properly if attached somewhere other than the correct tether anchor. 1. Position the child safety seat on the front seat cushion. 2. Route the child safety seat tether st...

Center seating location When installing a child safety seat in the front center position, route thetether strap over the center arm rest and clip it to the center anchor. Seating and Safety Restraints 105

STARTING Positions of the ignition 1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 2. LOCK, locks the steering wheel,automatic transmission gearshiftlever and allows key removal. Forvehicle equipped with a manualtransmission, you must depres...

Extended idling at high engine speeds can produce very hightemperatures in the engine and exhaust system, creating the risk of fire or other damage. Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the engine compartment and exhaust system,...

If starting a vehicle with an automatic transmission: • Make sure the parking brake isset. • Make sure the gearshift is in P(Park). If starting a vehicle with a manualtransmission: 1. Make sure the parking brake isset. 2. Push the clutch pedal to the floor. Driving 111

• Turn the key to 4 (ON) withoutturning the key to 5 (START). Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate. Starting the engine 1. Turn the key to...

Cold weather starting (flexible fuel vehicles only) In cold weather, ethanol fuel distributors should supply winter grade(E d 85) ethanol. If summer grade (E d 85) ethanol is used in cold weather, you may experience increased cranking times, rough idle or hesitationuntil the engine has warmed up. Co...

If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important ventilating information If the engine is idling while the vehicle is stopped for a long period oftime, open the windows at least 2.5 cm (one inch) or a...

Even when the ABS is disabled,normal braking is still effective. (Ifyour BRAKE warning lampilluminates with the parking brakereleased, have your brake systemserviced immediately.) Parking brake To set the parking brake (1), pressthe parking brake pedal down untilthe pedal stops. The BRAKE warning la...

AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever from being moved from P (Park) when the ignition isin the ON position unless the brake pedal is depressed. If you cannot move the gearsh...

Driving with a 5–speed automatic transmission (if equipped) Your transmission is equipped with an adaptive learning strategy found inthe vehicle computer. This feature is designed to increase durability, andprovide consistent shift feel over the life of the vehicle. A new vehicle ortransmission may ...

(Overdrive) The normal driving position for thebest fuel economy. Transmissionoperates in gears one throughfive. (Overdrive) can be deactivated by pressing thetransmission control switch on the end of the gearshift lever. This willilluminate the O/D OFF lamp and activate Drive. Drive (not shown) Dri...

MANUAL TRANSMISSION OPERATION (IF EQUIPPED) Using the clutch The manual transmission has a starter interlock that prevents crankingthe engine unless the clutch pedal is fully depressed. To start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor, then pu...

Upshifts when accelerating (for best fuel economy) Shift from: Transfer case position (if equipped) 2H or 4H 4L 1 -2 16 km/h (10 mph) 6 km/h (4 mph) 2 - 3 26 km/h (19 mph) 10 km/h (8 mph) 3 - 4 43 km/h (28 mph) 16 km/h (12 mph) 4 - 5 (Overdrive) 68 km/h (40 mph) 26 km/h (16 mph) Maximum downshift sp...

If your vehicle gets stuck in mud or snow If your vehicle gets stuck in mud or snow, it may be rocked out byshifting from forward and reverse gears, stopping between shifts in asteady pattern. Press lightly on the accelerator in each gear. Do not rock the vehicle if the engine is not at normal opera...

Using a manual 4WD system (if equipped) 2H (2WD High) – Power to the rear wheels only; used for street and highway driving. 4H (4WD High) – Used for extra traction such as in snow or icy roads or in off-road situations. Not intended for use on dry pavement. N (Neutral) – No power to either front or ...

Using the N (Neutral) position The transfer case N (Neutral) position overrides the transmissionand puts the vehicle in neutral regardless of transmissiongearshift lever position. The vehicle can move forward orbackward. This position should only be used when towing the vehicle. Do not leave the veh...

3. On vehicles equipped with an automatic transmission, place thetransmission in N (Neutral); on vehicles equipped with a manualtransmission, depress the clutch. 4. Move the 4WD control to the desired position. • If shifting into 4X4 LOW (4WD Low), wait for the LOW RANGE lightin the instrument clust...

If your vehicle goes off the edge of the pavement • If your vehicle goes off the edge of the pavement, slow down, butavoid severe brake application, ease the vehicle back onto thepavement only after reducing your speed. Do not turn the steeringwheel too sharply while returning to the road surface. •...

Mud and water If you must drive through highwater, drive slowly. Traction orbrake capability may be limited. When driving through water,determine the depth; avoid waterhigher than the bottom of the hubs(if possible) and proceed slowly. Ifthe ignition system gets wet, thevehicle may stall. Once throu...

slopes or hills . A danger lies in losing traction, slipping sideways and possibly rolling over. Whenever driving on a hill, determine beforehandthe route you will use. Do not drive over the crest of a hill withoutseeing what conditions are on the other side. Do not drive in reverseover a hill witho...

Do not use “aftermarket lift kits” or other suspension modifications,whether or not they are used with larger tires and wheels. These “aftermarket lift kits” could adversely affect the vehicle’s handlingcharacteristics, which could lead to loss of vehicle control or rollover andserious injury. Tires...

Ford Motor Company recommends that caution be used with any vehicleequipped with a high load or device (such as ladder racks or pickup boxcover). Failure to maintain your vehicle properly may void the warranty, increaseyour repair cost, reduce vehicle performance and operational capabilitiesand adve...

Special loading instructions for owners of pickup trucks andutility-type vehicles For important information regarding safe operation of this typeof vehicle, see the Preparing to drive your vehicle section in this chapter. Loaded vehicles may handle differently than unloaded vehicles.Extra precaution...

Towing trailers beyond the maximum recommended gross trailerweight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, loss of vehiclecontrol, vehicle rollover and personal injury. Preparing to tow Use the proper equipment for towing a trailer ...

Trailer tow connector Color Function Comment 1. Dark Green Trailer right-handturn signal Circuit activated when brakepedal is depressed or whenignition is on and right-handturn signal is applied. 2. Yellow Trailer left-hand turnsignal Circuit activated when brakepedal is depressed or whenignition is...

Trailer towing tips • Practice turning, stopping and backing up before starting on a trip toget the feel of the vehicle trailer combination. When turning, makewider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached. • The tra...

4x2 and 4x4 vehicles equipped with automatic transmissions: 4x2 vehicles with automatic transmissions or 4x4 vehicles with anelectronic-shift transfer case and automatic transmission, follow theseguidelines for recreational towing: • Release the parking brake. • Turn the key in the ignition to the O...

GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the New Vehicle Limited...

Canadian customers who require roadside assistance, call1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford MotorCompany will reimburse a reasonable amount. To obtain reimbursementinformation, U.S. Ford or Mercury vehicles customers call1-800-241-3673; Lincoln vehicle custo...

This switch is located in the frontpassenger’s footwell, by the kickpanel access cover. To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset theswitch by pushing in on the resetbutton. 4. Turn the ignition ON. 5. Wait a few seconds and...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and specifications chapter. 2.3L engine (if equipped) The high-current fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 50A** I/P fuse panel 2 — N...

If you use the temporary spare tire continuously or do not followthese precautions, the tire could fail, causing you to lose control of the vehicle, possibly injuring yourself or others. When driving with the temporary spare tire do not: • exceed 80 km/h (50 mph) or drive further than 3,200 km (2,00...

Tool Location Spare tire Under the vehicle, just forward ofthe rear bumper Jack, jack handle, wheel nut wrench Regular Cab: behind seats andunderneath the jack and toolscover SuperCab: stowed in the passengerside rear cab compartment orbehind the jump seat in a separatetool bag Four-door models: sto...

2. If equipped, unlock and removethe spare tire carrier lock from therear access hole located just abovethe rear bumper and below thetailgate. 3. Insert the straight end of the jackhandle into the rear access holelocated just above the rear bumperand below the tailgate. Forward motion will stop andr...

1. Park on a level surface, activatehazard flashers and place gearshiftlever in P (Park) (automatictransmission) or 1 (First) (manualtransmission). 2. Set the parking brake and turnengine OFF. 3. Block the diagonally oppositewheel. 4. Insert tapered end of the lugwrench behind hub caps and twistthem...

• Rear To lessen the risk ofpersonal injury, do not put any part of your body under thevehicle while changing a tire. Donot start the engine when yourvehicle is on the jack. The jack isonly meant for changing the tire. • Never use the differential as a jacking point. 7. Remove the wheel lug nuts wit...

Stowing the flat/spare tire 1. Lay the tire on the ground with the valve stem facing up. 2. Slide the wheel partially under the vehicle and install the wire andretainer through the center of the wheel. 3. Turn the jack handle clockwise until the tire is raised to its originalposition underneath the ...

Preparing your vehicle When the battery is disconnected or a new battery is installed, thetransmission must relearn its shift strategy. As a result, the transmissionmay have firm and/or soft shifts. This operation is considered normal andwill not affect function or durability of the transmission. Ov...

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second ...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Remove the jumper cable on the negative (...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, yourroadside assistance service provider. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingb...

GETTING THE SERVICES YOU NEED At home Ford Motor Company and Ford of Canada have authorized dealerships toservice your vehicle. It is preferred that you return to the authorizeddealer where your vehicle was purchased when warranty repairs areneeded. However, you may also take your vehicle to another...

In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action under the Magnuson-MossWarranty Act, or to the extent allowed by state law, before pursuingreplacement or repurchase remedies provided by certain state laws. Thisdispute handling procedure ...

Making a decision Board members review all available information related to eachcomplaint, including oral presentations, and arrive at a fair and impartialdecision. Board review may be terminated at any time by either party. Every effort is made to decide the case within 40 days of the date thatall ...

settlement have failed. This procedure is without cost to you and isdesigned to eliminate the need for lengthy and expensive legalproceedings. In the CAMVAP program, impartial third-party arbitrators conducthearings at mutually convenient times and places in an informalenvironment. These impartial a...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is availablefrom your dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can discolor and s...

PAINT CHIPS Your dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jam) toyour dealer to ensure you get the correct color. • Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and in...

• 4.0L SOHC V6 engine • Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your dealer. • For routine cleaning, use Motorcra...

INSTRUMENT PANEL AND CLUSTER LENS Clean the instrument panel with a damp cloth, then dry with a dry cloth. • Avoid cleaners or polish that increase the gloss of the upper portion ofthe instrument panel. The dull finish in this area helps protect thedriver from undesirable windshield reflection. Do n...

UNDERBODY Flush the complete underside of your vehicle frequently. Keep body anddoor drain holes free from packed dirt. FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Your Ford, Lincoln or Mercury dealer has many quality products availableto clean your vehicle and protect its finishes. These quality pr...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a scheduled maintenance guide which makes trackingroutine service easy. If your vehicle requires professional service, your dealership can providethe...

Working with the engine on • Automatic transmission: 1. Set the parking brake and shift to P (Park). 2. Block the wheels. • Manual transmission: 1. Set the parking brake, depress the clutch and place the gearshift in N(Neutral). 2. Block the wheels. Note: Do not start your engine with the air cleane...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Windshield washer fluid reservoir 2. Engine coolant reservoir 3. Engine oil dipstick 4. Transmission fluid dipstick (automatic transmission) 5. Engine oil filler cap 6. Brake fluid reservoir 7. Power distribution box 8. Clutch fluid ...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16–A2.Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic c...

ENGINE OIL Checking the engine oil Refer to the scheduled maintenance guide for the appropriate intervalsfor checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into theoil pan. 3. Set the parking brake and ensure t...

6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is between the MIN and MAX marks, the oil level is acceptable, DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough oil to raise the levelwithin the MIN-MAX range. • 2.3L I4 engine • 3.0L...

• 4.0L SOHC V6 engine • Oil levels above the MAX mark may cause engine damage. Some oilmust be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in...

Engine Oil Recommendations 2.3L & 3.0L Engines Look for this certificationtrademark. SAE 5W-20 engine oil is recommended. Change your engine oil and filter according to the appropriate schedulelisted in the scheduled maintenance guide.Do not use supplemental engine oil additives, oil treatments ...

If you see any corrosion on the battery or terminals, remove the cablesfrom the terminals and clean with a wire brush. You can neutralize theacid with a solution of baking soda and water. Batteries normally produce explosive gases which can causepersonal injury. Therefore, do not allow flames, spark...

• The vehicle may need to be driven to relearn the idle and fuel trimstrategy. • If you do not allow the engine to relearn its idle trim, the idlequality of your vehicle may be adversely affected until the idletrim is eventually relearned. When the battery is disconnected or a new battery installed,...

• Refer to the Scheduled Maintenance Guide for service intervalschedules. • Be sure to read and understand Precautions when servicing your vehicle in this chapter. If the engine coolant has not been checked at the recommended interval,the engine coolant reservoir may become low or empty. If the rese...

• Do not add/mix an orange-colored, extended life coolant suchas Motorcraft Speciality Orange Engine Coolant, VC-2 (US) orCXC-209 (Canada), meeting Ford specification WSS-M97B44–Dwith the factory-filled coolant. Mixing Motorcraft Speciality Orange Engine Coolant or any orange-colored extended life p...

5. Fill the coolant reservoir slowly with the proper coolant mixture (seeabove), to within the “cold fill range” or the “cold full” level on thereservoir. If you removed the radiator cap in an overflow system, fill theradiator until the coolant is visible and radiator is almost full. 6. Replace the ...

Severe climates If you drive in extremely cold climates (less than –36° C [–34° F]): • It may be necessary to increase the coolant concentrationabove 50%. • NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% willdecrease the overheat protection ch...

The fuel system may be under pressure. If the fuel filler cap isventing vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel mayspray out and injure you or others. If you do not use the proper fuel filler cap, excessive pressure or...

When refueling always shut the engine off and never allowsparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions.Care should be taken to avoid inhaling excess fumes. The flow of fuel through a fuel pump nozzle can produce st...

FFV engine (if equipped) Your FFV will operate well on ordinary “Regular” unleaded gasoline, butonly the highest quality fuel ethanol will provide the same level ofprotection and performance. To identify if your vehicle is an FFV, checkyour VIN or the label on the inside of your fuel filler door. Wh...

ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, thedriver. You must gather information as accurately and consistently aspossible. Fuel expense, frequency of fill-ups or fuel gauge readings areNOT accurate as a measure of fuel eco...

2. Each time you fill the tank, record the amount of fuel added (in litersor gallons). 3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current odometer reading. 4. Subtract your initial odometer reading from the current odometerreading. 5. Follow one of the simple cal...

• Warming up a vehicle on cold mornings is not required and mayreduce fuel economy. • Resting your foot on the brake pedal while driving may reduce fueleconomy. • Combine errands and minimize stop-and-go driving. Maintenance • Keep tires properly inflated and use only recommended size. • Operating a...

It is important to note the box in the lower left corner of the windowsticker. These numbers represent the Range of L/100 km (MPG)expected on the vehicle under optimum conditions. Your fuel economymay vary depending upon the method of operation and conditions. EMISSION CONTROL SYSTEM Your vehicle is...

If the vehicle’s powertrain system or its battery has just been serviced,the on-board diagnostics system is reset to a “not ready for I/M test”condition. To ready the on-board diagnostics system for I/M testing, aminimum of 30 minutes of city and highway driving is necessary asdescribed below: • Fir...

• 4.0L V6 engine Check the power steering fluid. Refer to the scheduled maintenanceguide for the service interval schedules. If adding fluid is necessary, useonly MERCON 威 ATF. 1. Start the engine and let it run until it reaches normal operatingtemperature (the engine coolant temperature gauge indic...

BRAKE FLUID RESERVOIR The fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels below the “MAX” linethat do not trigger the brake systemwarning lamp are within the normaloperating range, there is no need toadd fluid. If the fluid levels are ...

1. Clean the reservoir cap beforeremoval to prevent dirt and waterfrom entering the reservoir. 2. Remove cap and rubberdiaphragm from reservoir. 3. Add fluid until the level reachesthe step in the reservoir. 4. Reinstall rubber diaphragm andcap onto reservoir. TRANSMISSION FLUID Checking automatic t...

Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used. The type offluid used is normally indicated on the dipstick and also in the Lubricant specifications section in this chapter. Use of a non-approved automatic transmission fluid may causeinterna...

3. Fluid level should be at thebottom of the opening. 4. Add enough fluid through thefiller opening so that the fluid levelis at the bottom of the opening. 5. Install and tighten the fill plugsecurely. Use only fluid that meets Ford specifications. Refer to Lubricant Specifications in this chapter. ...

Use only fluid that meets Ford specifications. Refer to Lubricant Specifications in this chapter. DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Your vehicle may be equipped with universal joints that requirelubrication. Refer to the scheduled maintenance guide for maintenanceintervals. If the original uni...

SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has beenparked for at least one hour or has been driven less than 5 km (3miles). • Adjust tire pressure to recommended specifications found on theCe...

• Five tire rotation Note: Do not use a temporary spare tire for a 5 tire rotation. Replacing the tires Replace the tires when the wearband is visible through the tiretreads. Due to exposure to theelements and exhaust you shouldreplace the spare tire when youreplace the other tires. When replacing f...

Do not replace your tires with “high performance” tires or largersize tires. Failure to follow these precautions may adversely affect thehandling of the vehicle, and increase the risk of loss of vehicle control, vehicle rollover and/or personal injury. Tires that are larger or smaller than your vehi...

MOTORCRAFT PART NUMBERS Component 2.3L I4engine 3.0 L V6 engine 3.0L V6 FFV engine 4.0L V6 engine Air filterelement FA-1658 FA-1658 FA-1658 FA-1658 Fuel filter FG-1002 FG-1002 FG-1002 FG-1002 Battery BXT-59 BXT-59 BXT-59 BXT-59 Oil filter FL-400S FL-400S FL-400S FL-820S PCV valve EV-227 EV-130 EV-13...

Fluid Ford PartName Application Capacity Power steeringfluid MotorcraftMERCON 威 ATF All Fill to range ondipstick orreservoir Transmissionfluid 1 MotorcraftMERCON 威 ATF 5-speed manual 2.65L (2.8quarts) 3 MotorcraftMERCON 威 V ATF 4x2 vehicleswith automaticand 2.3L I4engine 9.4L (9.9quarts) 2 4x2 vehic...

Fluid Ford PartName Application Capacity Engine coolant 4 MotorcraftPremium EngineCoolant(green-colored) or Motorcraft Premium GoldEngine Coolant(yellow-colored) 2.3 L I4 enginewith manualtransmission 10.0L (10.5quarts) 2.3L I4 enginewith automatictransmission 9.7L (10.2quarts) 3.0L V6 enginewith ma...

LUBRICANT SPECIFICATIONS Item Ford part nameor equivalent Ford partnumber Fordspecification Front axle (4X4) Motorcraft SAE80W-90 PremiumRear AxleLubricant XY-80W90-QL WSP-M2C197-A Rear axle Motorcraft SAE80W-90 PremiumRear AxleLubricant 1 XY-80W90-QL WSP-M2C197-A Rear axle (FX4only) Motorcraft SAE7...

Item Ford part nameor equivalent Ford partnumber Fordspecification Engine oil 2.3L and 3.0Lengines Motorcraft SAE5W-20 PremiumSynthetic BlendMotor Oil XO-5W20-QSP WSS-M2C153-Hand APICertificationMark 4.0L engines Motorcraft SAE5W-30 SuperPremium MotorOil XO-5W30-QSP WSS-M2C205–Aand APICertificationM...

VEHICLE DIMENSIONS Vehicledimensions Regular CabShort WheelBase (SWB) mm(in) Regular CabLong WheelBase (LWB)mm (in) Supercab mm(in) (1) Overalllength 4 763 (187.5) 5 093 (200.5) 5 153 (202.9) (2) Overallwidth 1 785 (70.3) 1 785 (70.3) 1 785 (70.3) (3) Overallheight 4x2/4x4 1 593.5 (62.7) /1 655 (65....

FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of genuine Ford accessories are available for yourvehicle through your local authorized Ford, Lincoln Mercury or Ford ofCanada dealer. These quality accessories have been specificallyengineered to fulfill your automotive needs; they are custom desig...

Bed tent (Short bed, Styleside only) Cellular phone holder Compass mirror Compass mirror with outside temperature reading Daytime running lights First aid kit Fog lights Peace of mind kit Pickup box rails (tubular) Removable bike carrier (bed mount/hitch mount) Running boards/bars Speed control Trai...

A Air bag supplemental restraintsystem ..........................................85 and child safety seats ..............87description ................................85disposal ......................................90driver air bag ............................88indicator light ........................