Ford 2003 Mustang v.2- Manuals

Protecting the environment We must all play ourpart in protecting theenvironment. Correctvehicle usage and theauthorized disposal of waste cleaning and lubricationmaterials are significant steps towards this aim.Information in this respect is highlighted in thisguide with the tree symbol. BREAKING-I...

SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty includesBumper-to-Bumper Coverage, Safety RestraintCoverage, Corrosion Coverage, and 7.3L PowerStroke Diesel Engine Coverage. In addition, yourvehicle is eligible for Emissions Defect andEmissions Performance Warranties. For a detail...

These are some of the symbols you may see on yourvehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child SeatInstallation Warning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock BrakeSystem Brake Fluid -Non-...

WARNING LIGHTS AND CHIMES Base instrument cluster Optional instrument cluster Mach 1 instrument cluster Warning lights and gauges can alert you to a vehiclecondition that may become serious enough to causeexpensive repairs. A warning light may illuminatewhen a problem exists with one of your vehicle...

Service engine soon: If this light illuminateswhile driving, it is apossible indication thatone of the engine’s emission control systems has failed. Check fuel cap: Illuminates when thefuel cap may not beproperly installed.Continued driving with this light on may cause theService engine soon light t...

Air bag readiness: If this light fails toilluminate whenignition is turned to ON, continues to flash orremains on, have the system serviced immediately. Achime will also sound when a malfunction in thesupplemental restraint system has been detected. Safety belt: Reminds you to fasten yoursafety belt...

Turn signal: Illuminates when theleft or right turn signalor the hazard lights are turned on. If the indicatorsstay on or flash faster, check for a burned out bulb. High beams: Illuminates when thehigh beam headlampsare turned on. Key-in-ignition warning chime: Sounds when the key is left in the ign...

Mach 1 instrument cluster gauges Speedometer: Indicates the current vehicle speed. • Base instrument cluster • Optional instrument cluster • Mach 1 instrument cluster Engine coolanttemperature gauge: Indicates enginecoolant temperature. Atnormal operating temperature, the needle will be inthe normal...

AM/FM STEREO / SINGLE CD RADIO 1. Balance: Press / to shift sound to the left/rightspeakers. 2. Fade: Press / to shift sound to thefront/rear speakers. 3. SCN (Scan): Press to hear a brief samplingof all listenable stationsor CD tracks. Press again to stop. 4. CLK: To set the hour, press and holdCLK...

6. COMP (Compression): In CD mode, press to bringlouder and softer levels into more comfortablelistening level. The compression icon (c) will appearin the display. 7. Shuffle: Press to listen to the tracks onthe CD in randomorder. Press again to turn off. 8. Memory presets: To set a station: Selectf...

10. CD (Rewind): Press and hold untilthe desired selectionpoint is reached. This function is not enabled in MP3mode. 11. MP3 directory: Allows you to listen tosongs in MP3 flat filemode and MP3 directory mode. • Insert a MP3 disc to engage in the flat file mode.The MP3 icon will be displayed. • Whil...

17. Power/volume: Press to turn ON/OFF;turn to increase ordecrease volume levels. 18. CD: Press CD to play a CD or MP3 disc.When the MP3 disc isloaded, CD and LOAD will appear on the display.The display will briefly show the total number oftracks on the disc as TXXX (XXX=number oftracks). 19. AM/FM:...

Your MACH 威 MP3 player is also equipped with an anti-shock buffer for MP3 discs. MP3 FILE DIRECTORY STRUCTURE The MACH 威 MP3 music system recognizes MP3 disc file and directory (folder) structure as follows: • There are two different modes for MP3 discplayback: MP3 flat file mode (default) and MP3di...

MACH 姞 460 SOUND SYSTEM RADIO (CD CHANGER COMPATIBLE) MACH 姞 1000 SOUND SYSTEM RADIO (CD CHANGER COMPATIBLE) Your vehicle may be equipped with the MACH 1000 威 audio system. This system is equipped with a rack of amplifiers and subwoofers in the trunk of thevehicle. Do not store or rest items on the ...

5. Eject: Press EJ and choose thecorresponding preset(1–6) to eject the desired CD. Press and hold toeject all loaded discs. 6. Bass: Press BASS; then pressSEL / to decrease/increase the bass output. Treble: Press TREB; then pressSEL / to decrease/increase the treble output. 7. Select: Use with Bass...

Show TYPE: Displays the station’s call letters and format. Compression: Brings soft and loud CD passages together for a more consistent listening level. 10. Memory presets: To set a station: Selectfrequency bandAM/FM; tune to a station, press and hold a presetbutton until sound returns. In CD mode, ...

14. Load: Press LOAD and the correspondingpreset (1–6) to load aCD into the desired slot. Press and hold to load upto six discs at once. 15. Shuffle: Press to play tracks/discs inrandom order. PressSHUF to cycle through SHUF DISC, SHUF TRAC orSHUF OFF. 16. Scan: Press to move up the radiofrequency b...

RADIO RECEPTION FACTORS There are three factors that can effect radioreception: • Distance/strength: The further you travel from anFM station, the weaker the signal and the weakerthe reception. • Terrain: Hills, mountains, tall buildings, powerlines, electric fences, traffic lights andthunderstorms ...

peel and cause the CD to become jammed. It isrecommended that homemade CDs be identifiedwith permanent felt tip marker rather thanadhesive labels. Ball point pens may damageCDs. Please contact your dealer for furtherinformation. AUDIO SYSTEM WARRANTY AND SERVICE Refer to the Warranty Guide for audio...

MANUAL HEATING AND AIR CONDITIONINGSYSTEM 1. Fan speed adjustment: Controls the volume of aircirculated in thevehicle. 2. Temperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for...

• Under normal weather conditions, do not leavethe air flow selector in MAX A/C or OFF when thevehicle is parked. This allows the vehicle to“breathe” using the outside air inlet vents. • Do not put objects under the front seats that willinterfere with the air flow to the back seats. • Remove any sno...

HEADLAMP CONTROL • The first positionturns on the parking,tail, license plate andside marker lamps. • The outer positionturns on theheadlamps. Foglamp control (if equipped) The foglamps can beturned on when theheadlamp control is ineither of the followingpositions: • Parking lamps • Low beams Press ...

High beams Push the lever towardthe instrument panel toactivate. Pull the levertowards you todeactivate. Flash to pass Pull toward you slightlyto activate and releaseto deactivate. PANEL DIMMER CONTROL To adjust thebrightness of theinstrument panel: • Rotate clockwise/counterclockwisewhen the headla...

Headlamp vertical aim adjustment 1. Park the vehicle on a level surface approximately7.6 meters (25 feet) from a vertical wall or screendirectly in front of it. • (1) Eight feet • (2) Center height of lamp to ground • (3) Twenty five feet • (4) Horizontalreference line 2. Measure the heightfrom the ...

6. HORIZONTAL AIM IS NOT REQUIRED FOR THISVEHICLE AND IS NON-ADJUSTABLE. 7. Close the hood and turn off the lamps. TURN SIGNAL CONTROL • Push down toactivate the left turnsignal. • Push up to activatethe right turn signal. INTERIOR LAMPS Map lamps (if equipped) If equipped with aconvertible top them...

BULBS Replacing exterior bulbs Check the operation of all the bulbs frequently. Using the right bulbs Replacement bulbs are specified in the chart below.Headlamp bulbs must be marked with an authorized“D.O.T.” for North America and an “E” for Europe toassure lamp performance, light brightness andpat...

Replacing headlamp bulbs To remove the headlamp bulb: 1. Make sure headlamp switch is in the OFFposition, then open the hood. 2. At the back of theheadlamp, pull tworetainer pins up torelease the headlampassembly. 3. Pull headlampassembly forward anddisconnect theelectrical connector from the bulb b...

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of thecontrol away from youto increase the intervalspeed of the wipers;rotate towards you todecrease the interval speed of the wipers. • Top two positions are for LO and HI speedconstant wipe. Windshield washer: Push the end of thestalk: • briefl...

POWER SIDE VIEW MIRRORS (IF EQUIPPED) To adjust your mirrors: 1. Move the mirrorselector control all theway to the left toadjust the left mirroror all the way to theright to adjust the rightmirror. 2. Move the control in the direction you wish to tiltthe mirror. 3. Return the control to the center p...

CENTER CONSOLE Your vehicle may be equipped with a variety ofconsole features. These include: • Dual cupholders • Auxiliary power point • Coin holder slots (if equipped) • Convertible top control (if equipped) Use only soft cups in the cupholder. Hardobjects can injure you in a collision. Cell phone...

POSITIVE RETENTION FLOOR MAT(IF EQUIPPED) Position the floor mat sothat the eyelet is over thepointed end of theretention post and rotateforward to lock in. Makesure that the mat does notinterfere with the operationof the accelerator or thebrake pedal. To remove thefloor mat, reverse the installatio...

4. Close the windshield header clamps immediatelyafter disengagement, to avoid cutting the topmaterial and to permit installation of the vinyl boot. 5. If the top has notbeen lowered for sometime and sticks to thewindshield header,push the front of thetop up slightly withyour hand to loosen it. 6. P...

3. Insert boot tongueinto groove located onrear of seat. 4. To remove, unfastenthe snaps or pivotlatches and the boottongue. 5. Pull forward and liftoff. Raising the convertible top The convertible top will not operate unless the parking brake is engaged. Do not raise the top whilethe vehicle is mov...

8. To fasten both clamps securely, push the clamphandles into the header on the top until they areflush with the header. Pulling down on the header atthe center grip while closing the latches may assistin fastening the clamps. 9. Raise the front and rear side windows. 10. Disengage the parking brake...

KEYS The key operates all locks on your vehicle. In case ofloss, replacement keys are available from yourdealer. You should always carry a second key with you in asafe place in case you require it in an emergency. Refer to SecuriLock 娂 Passive Anti-Theft System for more information. POWER DOOR LOCKS...

How to reprogram your remote entrytransmitters You must have all remote entry transmitters (maximum of four) available before beginning thisprocedure. To reprogram theremote entrytransmitters: 1. Ensure the vehicle iselectronically unlocked. 2. Put the key in theignition. 3. Turn the key from the 2 ...

Illuminated entry The interior lamps illuminate when the remote entrysystem is used to unlock the door(s) or sound thepersonal alarm. The illuminated entry system will turn off theinterior lights if: • the ignition switch is turned to the ON position,or • the remote transmitter lock control is press...

start systems. Use of these systems may result invehicle starting problems and a loss of securityprotection. Note: Large metallic objects, electronic devices that are used to purchase gasoline or similar items, or asecond coded key on the same key chain may causevehicle starting issues. You need to ...

Automatic disarming Switching the ignition to the 4 (ON) position with a coded key disarms the vehicle. • The THEFT indicator will illuminate for three seconds and then go out. • If the THEFT indicator stays on for an extended period of time or flashes rapidly, have the systemserviced by your dealer...

1. Insert a previouslyprogrammed coded keyinto the ignition. 2. Turn the ignitionfrom the 3 (OFF)position to the 4 (ON)position. Keep theignition in the 4 (ON)position for at least one second, but no more than10 seconds. 3. Turn the ignition to the 3 (OFF) position, andremove the coded key from the ...

SEATING Notes: Reclining the seatback can cause anoccupant to slide under the seat’s safety belt, resulting in severe personal injuries in theevent of a collision. Do not pile cargo higher than the seatbacksto reduce the risk of injury in a collision or sudden stop. Adjustable head restraints Head r...

Adjusting the front manual seat Never adjust the driver’s seat or seatbackwhen the vehicle is moving. Always drive and ride with your seatbackupright and the lap belt snug and low across the hips. Lift handle to moveseat forward orbackward. Pull lever up to adjustseatback. Using the power lumbar sup...

REAR SEATS Use the seatbackrelease to fold the backof the front seatforward for rear seatpassenger entry or exit.This release handle islocated on the loweroutboard back of theseat. The seatbacklocks automatically when returned to the normalposition.The rotating boot on the front seat belt is designe...

SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatbackupright and the lap belt snug and low across the hips. To reduce the risk of injury, make surechildren sit where they can be properly restrained. Never let a passenger hold a child on his orher lap while the vehi...

Each seating position in your vehicle has aspecific safety belt assembly which is made up of one buckle and one tongue that are designedto be used as a pair. 1) Use the shoulder belt onthe outside shoulder only. Never wear the shoulderbelt under the arm. 2) Never swing the safety beltaround your nec...

2. To unfasten, pushthe release button andremove the tonguefrom the buckle. The front and rear outboard safety restraints in thevehicle are combination lap and shoulder belts. Thefront passenger and rear seat outboard safety beltshave two types of locking modes described below: Energy Management Fea...

Failure to replace the Belt and Retractorassembly could increase the risk of injury in collisions. Vehicle sensitive mode This is the normal retractor mode, which allows freeshoulder belt length adjustment to your movementsand locking in response to vehicle movement. Forexample, if the driver brakes...

Reasons given... Consider... “The people I’m withdon’t wear belts” Set the example, teen deathsoccur 4 times more often invehicles with TWO or MOREpeople. Children and youngerbrothers/sisters imitate behaviorthey see. “I have an air bag” Air bags offer greater protectionwhen used with safety belts.F...

Important SRS precautions The SRS is designed towork with the safetybelt to help protect thedriver and right frontpassenger from certainupper body injuries.Air bags DO NOTinflate slowly; there isa risk of injury from adeploying air bag. All occupants of the vehicle, including thedriver, should alway...

Do not put anything on or over the air bagmodule. Placing objects on or over the air bag inflation area may cause those objects to bepropelled by the air bag into your face and torsocausing serious injury. Do not attempt to service, repair, or modifythe air bag supplemental restraint systems or its ...

of position at the time of air bag deployment. It isextremely important that occupants be properlyrestrained as far away from the air bag module aspossible while maintaining vehicle control. The SRS consists of: • driver and passenger air bag modules (whichinclude the inflators and air bags) • one o...

A difficulty with the system is indicated by one ormore of the following: • The readiness lightwill either flash orstay lit. • The readiness light will not illuminate immediatelyafter ignition is turned on. • A series of five beeps will be heard. The tonepattern will repeat periodically until the pr...

restrained in the rear seating positions than in thefront seating position. Never let a passenger hold a child on his orher lap while the vehicle is moving. The passenger cannot protect the child from injury in acollision. Always follow the instructions and warnings thatcome with any infant or child...

Booster seats position a child so that safety belts fitbetter. They lift the child up so that the lap beltrests low across the hips and the knees bendcomfortably. Booster seats also make the shoulderbelt fit better and more comfortably for growingchildren. When children should use booster seats Chil...

restraint, a backless booster seat may place yourchild’s head (top of ear level) above the top of theseat. In this case, move the backless booster toanother seating position with a higher seat backand lap/shoulder belts. • Those with a highback. If, with a backlessbooster seat, youcannot find a seat...

Never use pillows, books, or towels to boosta child. They can slide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the sizeand weight of the child. Carefully follow all o...

Installing child safety seats with combinationlap and shoulder belts If you must use aforward facing childseat in the front seat(reminder - children 12years old and undershould always beproperly restrained inthe rear seat) the shoulder belt mustbe routed throughthe belt guide at thetop of the seatba...

The rear seats of your vehicle are equipped withbuilt-in tether strap anchors located behind the seatson the package tray behind the speakers (coupe) oron the lower backside of the seatback (convertible). The tether anchors in your vehicle are either locatedunder a cover marked with the child tether...

For Coupe only: 4. Open the tetheranchor covers. 5. Clip the tether strapto the anchor asshown. For Convertible only: The tether anchors onthe convertible arelocated on the lowerbackside of theseatback. 4. Access tetheranchors located behindthe seatback and pullaway vinyl flap toexpose anchors. 5. C...

Your vehicle has LATCH anchors for child seatinstallation at the seating positions marked with thechild seat symbol. The center ofthe rear seat is NOT designed as a seating position. TheLATCH anchors werenot designed to beused with a childseat in the centerposition and there isno tether anchoravaila...

STARTING Positions of the ignition 1. ACCESSORY, allowsthe electricalaccessories such as theradio to operate whilethe engine is notrunning. 2. LOCK, locks thesteering wheel, automatic transmission gearshiftlever and allows key removal. For vehicle equippedwith a manual transmission, you must depress...

Preparing to start your vehicle Engine starting is controlled by the powertraincontrol system. This system meets all CanadianInterference-Causing Equipment standardrequirements regulating the impulse electrical fieldstrength of radio noise. When starting a fuel-injected engine, don’t press theaccele...

Starting the engine 1. Turn the key to 4(ON) without turningthe key to 5 (START). 2. Turn the key to 5(START), then releasethe key as soon as theengine starts.Excessive crankingcould damage the starter. Note: If the engine does not start within five seconds on the first try, turn the key to 3 (OFF),...

Important ventilating information If the engine is idling while the vehicle is stoppedfor a long period of time, open the windows at least2.5 cm (one inch) or adjust the heating or airconditioning to bring in fresh air. BRAKES Occasional brake noise is normal. If a metal-to-metal,continuous grinding...

result in a permanent reduction in effectiveness.This loss of effectiveness does not affect normaldriving and should not be noticeable to the driver. To reduce the risk of injury, never run theengine with one wheel off the ground, such as when changing a tire. AUTOMATIC TRANSMISSION OPERATION(IF EQU...

Always set the parking brake fully and makesure the gearshift is latched in P (Park). Turn the ignition to the LOCK position and removethe key whenever you leave your vehicle. R (Reverse) With the gearshift lever in R (Reverse), the vehiclewill move backward. Always come to a completestop before shi...

2 (Second) This position allows for second gear only. • Provides engine braking. • Use to start-up on slippery roads. • To return to D (Overdrive), move the gearshiftlever into the D (Overdrive) position. • Selecting 2 (Second) at higher speeds will causethe transmission to downshift to second gear ...

MANUAL TRANSMISSION OPERATION(IF EQUIPPED) Using the clutch The manual transmission has a starter interlock thatprevents cranking the engine unless the clutch pedalis fully depressed. To start the vehicle: 1. Make sure the parking brake is fully set. 2. Press the clutch pedal to the floor, then put ...

Upshift according to the following chart: Upshifts when accelerating (recommended for best fuel economy) Shift from: 1 - 2 18 km/h (11 mph) 2 - 3 31 km/h (19 mph) 3 - 4 48 km/h (30 mph) 4 - 5 64 km/h (40 mph) Reverse 1. Make sure that your vehicle is at a complete stopbefore you shift into R (Revers...

DRIVING THROUGH WATER Do not drive quickly through standing water,especially if the depth is unknown. Traction or brakecapability may be limited and if the ignition systemgets wet, your engine may stall. Water may alsoenter your engine’s air intake and severely damageyour engine. If driving through ...

• GVWR (Gross Vehicle Weight Rating): Maximum permissible total weight of the basevehicle, occupants, optional equipment and cargo.The GVWR is specific to each vehicle and is listedon the Safety Certification Label on the driver’sdoor pillar. • GAWR (Gross Axle Weight Rating): Carrying capacity for ...

Do not use replacement tires with lower loadcarrying capacities than the originals because theymay lower the vehicle’s GVWR and GAWRlimitations. Replacement tires with a higher limitthan the originals do not increase the GVWR andGAWR limitations. The Safety Certification Label, found on the driver’s...

GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicleconcern, Ford Motor Company offers acomplimentary roadside assistance program. Thisprogram is separate from the New Vehicle LimitedWarranty. The service is available: • 24–hours, seven days a week • for the New Vehicle Limited ...

USING ROADSIDE ASSISTANCE Complete the roadside assistance identification cardand place it in your wallet for quick reference. In theUnited States, this card is found in the Owner Guideportfolio in the glove compartment in Ford vehiclesand is mailed to you if you own a Mercury orLincoln. In Canada, ...

HAZARD FLASHER The hazard flasher islocated on the steeringcolumn, just behind thesteering wheel. Thehazard flashers willoperate when theignition is in anyposition. Push in the flasher control and all front and reardirection signals will flash. Press the flasher controlagain to turn them off. Use it...

FUSES AND RELAYS Fuses If electricalcomponents in thevehicle are notworking, a fuse mayhave blown. Blownfuses are identified by a broken wire within the fuse.Check the appropriate fuses before replacing anyelectrical components. Note: Always replace a fuse with one that has the specified amperage ra...

Passenger compartment fuse panel The fuse panel is located below and to the left ofthe steering wheel by the brake pedal. Remove thepanel cover to access the fuses. To remove a fuse use the fuse puller tool providedon the fuse panel cover. The fuses are coded as follows: Fuse/Relay Location Fuse Amp...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 34 20A Instrument Cluster, CCRM,Data link connector,Securilock transceivermodule 35 15A Shift lock actuator,Powertrain Control Module(PCM), Speed control servo,ABS module 36 15A Air bag control module 37 5A Adjustable i...

The high-current fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description Relay 1 — Fog lamp interrupt Relay 2 — Interval wiper Relay 3 — Wiper HI/LO Relay 4 — Starter Relay 5 — Fog lamps 1 50A** (4.6L), 30A CB (3.8L) Electric cooling fan motor 2 30A** Headl...

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 14 20A* Fuel pump 15 30A* MACH 1000 right amplifiers 16 20A* Horn 17 20A* ABS 18 30A* Power seats 19 10A* Intercooler pump (Cobraonly) 20 20A* Alternator 21 — Not used 22 — Not used 23 — Not used 24 20A* A/C pressure 25 — Not use...

and is designed for emergency use only. Replace thistire with a full-size tire as soon as possible. If you use the temporary spare tirecontinuously or do not follow these precautions, the tire could fail, causing you to losecontrol of the vehicle, possibly injuring yourself orothers. When driving wi...

To lessen the risk of personal injury, do notput any part of your body under the vehicle while changing a tire. Do not start the enginewhen your vehicle is on the jack. The jack is onlymeant for changing the tire. 5. Remove the lug nuts with the lug wrench. 6. Replace the flat tire with the spare ti...

To remove theanti-theft lug nut: 1. Insert the key overthe locking lug nut.Make sure you hold the key square to the lug nut. Ifyou hold the key at an angle, you could damage thekey and the lug nut. 2. Place the lug nut wrench over the lug nut key andapply pressure on the key with the wrench. 3. Turn...

1. Use only a 12–volt supply to start your vehicle. 2. Do not disconnect the battery of the disabledvehicle as this could damage the vehicle’s electricalsystem. 3. Park the booster vehicle close to the hood of thedisabled vehicle making sure the two vehicles do not touch. Set the parking brake on bo...

2. Connect the other end of the positive (+) cable tothe positive (+) terminal of the assisting battery. 3. Connect the negative (-) cable to the negative (-)terminal of the assisting battery. 4. Make the final connection of the negative (-)cable to an exposed metal part of the stalledvehicle’s engi...

5. Ensure that the cables are clear of fan blades,belts, moving parts of both engines, or any fueldelivery system parts. Jump starting 1. Start the engine of the booster vehicle and runthe engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle...

WRECKER TOWING If you need to have your vehicle towed, contact aprofessional towing service or, if you are a member,your roadside assistance center. It is recommended that your vehicle be towed withflatbed equipment. Do not tow with slingbelt orwheel lift equipment. Ford Motor Company has notapprove...

GETTING THE SERVICES YOU NEED At home Ford Motor Company and Ford of Canada haveauthorized dealerships to service your vehicle. It ispreferred that you return to the authorized dealerwhere your vehicle was purchased when warrantyrepairs are needed. However, you may also take yourvehicle to another F...

In the United States: Ford Motor CompanyCustomer Relationship Center16800 Executive Plaza DriveP.O. Box 6248Dearborn, Michigan 481211-800-392-3673 (FORD)(TDD for the hearing impaired: 1-800-232-5952)www.ford.com In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000...

• Your telephone number (home and business) • The name of the dealer and the city where thedealership is located • The year and make of your vehicle • The date of vehicle purchase • The current odometer reading • The vehicle identification number (VIN) If you still have a complaint involving a warra...

You may purchase Ford ESP from any participatingFord and Lincoln Mercury and Ford of Canadadealer. There are several plans available in varioustime, distance and deductible combinations whichcan be tailored to fit your own driving needs. FordESP also offers reimbursement benefits for towingand renta...

written new vehicle warranty are eligible for review,except those involving: • a non-Ford product • a non-Ford dealership • sales disputes between customer and dealerexcept those associated with warranty repairs orconcerns with the vehicle’s performance asdesigned • a request for reimbursement of co...

You will receive a letter of explanation if yourapplication does not qualify for Board review. Oral presentations If you would like to make an oral presentation,indicate YES to question 6 on the application. Whileit is your right to make an oral presentation beforethe Board, this is not a requiremen...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarmwater and a neutral Ph shampoo, such as MotorcraftDetail Wash (ZC-3–A), which is available from yourdealer. • Never use strong household detergents or soap,such as dish washing or laundry liquid. Theseproducts can discolor and spo...

ENGINE Engines are more efficient when they are cleanbecause grease and dirt buildup keep the enginewarmer than normal. When washing: • Take care when using a power washer to cleanthe engine. The high-pressure fluid couldpenetrate the sealed parts and cause damage. • Do not spray a hot engine with c...

INSTRUMENT PANEL AND CLUSTER LENS Clean the instrument panel with a damp cloth, thendry with a dry cloth. • Avoid cleaners or polish that increase the gloss ofthe upper portion of the instrument panel. Thedull finish in this area helps protect the driverfrom undesirable windshield reflection. Do not...

LEATHER SEATS (IF EQUIPPED) Your leather seating surfaces have a clear, protectivecoating over the leather. • To clean, use a soft cloth with Motorcraft DeluxeLeather and Vinyl Cleaner (ZC-11–A). Dry thearea with a soft cloth. • To help maintain its resiliency and color, use theMotorcraft Deluxe Lea...

Motorcraft Deluxe Leather and Vinyl Cleaner (notavailable in Canada) (ZC-11–A) Ford Extra Strength Tar and Road Oil Remover*(not available in Canada) (B7A-19520–AA) Ford Extra Strength Upholstery Cleaner (notavailable in Canada) (E8AZ-19523–AA) Motorcraft Custom Bright Metal Cleaner (ZC-15) Motorcra...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the enginecompartment for easy location. • We provide a scheduled maintenance guide whichmakes tracking routine service easy. If your vehicle requires professional service, yourdealership can provide the...

• Manual transmission: 1. Set the parking brake, depress the clutch andplace the gearshift in 1 (First). 2. Turn off the engine and remove the key. 3. Block the wheels. Working with the engine on • Automatic transmission: 1. Set the parking brake and shift to P (Park). 2. Block the wheels. • Manual ...

2. Go to the front of the vehicle and release theauxiliary latch that is located under the front centerof the hood. 3. Lift the hood and secure it with the prop rod. Maintenance and Specifications 156

WINDSHIELD WASHER FLUID Add fluid to fill thereservoir if the level islow. In very coldweather, do not fill thereservoir completely. Only use a washerfluid that meets FordspecificationWSB-M8B16–A2. Referto Lubricant specifications in this chapter. State or local regulations on volatile organiccompou...

3. Set the parking brake and ensure the gearshift issecurely latched in P (Park) (automatictransmissions) or 1 (First) (manual transmissions). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil levelindicator (dipstick). • 3.8L V6 engine • 4.6L SOHC V8...

6. Wipe the indicator clean. Insert the indicator fully,then remove it again. • If the oil level is between the MIN—MAX marks, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MIN mark, add enoughoil to raise the level within the MIN—MAX range. • 3.8L V6 engine • 4.6L SOH...

• Oil levels above the MAX mark may cause enginedamage. Some oil must be removed from theengine by a service technician. 7. Put the indicator back in and ensure it is fullyseated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the...

optimum fuel economy and durabilityperformance meeting all requirements for yourvehicle’s engine . Do not use supplemental engine oil additives, oiltreatments or engine treatments. They areunnecessary and could, under certain conditions,lead to engine damage which is not covered by yourwarranty. Cha...

Keep batteries out of reach of children.Batteries contain sulfuric acid. Avoid contact with skin, eyes or clothing. Shield your eyes whenworking near the battery to protect againstpossible splashing of acid solution. In case of acidcontact with skin or eyes, flush immediately withwater for a minimum...

be adversely affected until the idle trim iseventually relearned. When the battery is disconnected or a new batteryinstalled, the transmission must relearn its adaptivestrategy. As a result of this, the transmission mayshift firmly. This operation is considered normal andwill not affect function or ...

concentration of coolant falls below 40% or above60%, the engine parts could become damaged or notwork properly. A 50–50 mixture of coolant and water provides the following: • freeze protection down to -36° C (-34° F) • boiling protection up to 129° C (265° F) • protection against rust and other for...

may become low or empty. If the reservoir is low orempty, add engine coolant to the reservoir. Refer to Adding engine coolant in this chapter. Note: Automotive fluids are not interchangeable; do not use engine coolant, antifreeze or windshieldwasher fluid outside of its specified function andvehicle...

If you must remove the pressure relief cap orradiator cap (depending upon engine application),follow these steps to avoid personal injury: 1. Before you remove the cap, turn the engine offand let it cool. 2. When the engine is cool, wrap a thick clotharound the cap. Slowly turn cap counterclockwiseu...

7. Add a 50/50 mixture of engine coolant and distilled water to the engine coolant reservoir untilthe coolant level is at the “cold fill level” as listed onthe reservoir. 8. Reinstall the pressure relief cap. 9. Check the coolant level in the reservoir beforeyou drive your vehicle the next few times...

Ford Motor Company does NOT recommend the useof recycled engine coolant in vehicles originallyequipped with Motorcraft Premium Gold EngineCoolant since a Ford-approved recycling process isnot yet available. Used engine coolant should be disposed of in an appropriate manner. Follow your community’sre...

• Decreased engine coolant concentrationsbelow 40% will decrease the corrosionprotection characteristics of the enginecoolant and may cause engine damage. • Decreased engine coolant concentrationsbelow 40% will decrease the freezeprotection characteristics of the enginecoolant and may cause engine d...

Automotive fuels can cause serious injury ordeath if misused or mishandled. Gasoline may contain benzene, which is acancer-causing agent. Observe the following guidelines when handlingautomotive fuel: • Extinguish allsmoking materialsand any open flamesbefore fueling yourvehicle. • Always turn off t...

treatment of alcoholism. Breathing gasolinevapors, or skin contact could cause an adversereaction. In sensitive individuals, serious personalinjury or sickness may result. If fuel is splashedon the skin, promptly wash skin thoroughly withsoap and water. Consult a physician immediatelyif you experien...

cause these problems to become more pronounced.If the problems persist, see your dealer or a qualifiedservice technician. It should not be necessary to add any aftermarketproducts to your fuel tank if you continue to usehigh quality fuel of the recommended octane rating.Aftermarket products could ca...

of the advertised capacity of the fuel tank dueto the empty reserve still present in the tank. For consistent results when filling the fuel tank: • Turn the engine/ignition switch to the off positionprior to refueling, an error in the reading willresult if the engine is left running. • Use the same ...

Keep a record for at least one month and record thetype of driving (city or highway). This will providean accurate estimate of the vehicle’s fuel economyunder current driving conditions. Additionally,keeping records during summer and winter will showhow temperature impacts fuel economy. In general,l...

EPA window sticker Every new vehicle should have the EPA windowsticker. Contact your dealer if the window sticker isnot supplied with your vehicle. The EPA windowsticker should be your guide for the fuel economycomparisons with other vehicles. It is important to note the box in the lower leftcorner ...

ready the on-board diagnostics system for I/Mtesting, a minimum of 30 minutes of city andhighway driving is necessary as described below: • First, at least 10 minutes of driving on anexpressway or highway. • Next, at least 20 minutes driving in stop-and-go,city-type traffic with at least four idle p...

4. Check the fluid level on the dipstick. It should bewithin the FULL HOT range. Do not add fluid if thelevel is within this range. 5. If the fluid is low, add fluid in small amounts,continuously checking the level until it reaches thecorrect operating range. Be sure to put the cap backon the reserv...

• 3.8L OHV V6 engine • 4.6L SOHC V8 /4.6L 4v V8 (Mach 1)engine 1. Clean the reservoir cap before removal to preventdirt or water from entering the reservoir. 2. Visually inspect thefluid level. 3. If necessary, addbrake fluid from a cleanun-opened containeruntil the level reaches MAX. Do not fill ab...

If you use a brake fluid that is not DOT 3,you will cause permanent damage to your brakes. Do not let the reservoir for the mastercylinder run dry. This may cause the brakes to fail. CLUTCH ADJUSTMENT (IF EQUIPPED) Check the clutchadjustment. Refer tothe scheduledmaintenance guide forthe service int...

SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, afterthe vehicle has been parked for at least one houror has been driven less than 5 km (3 miles). • Adjust tire pressure to recommendedspecifications found on the ce...

• 17 inch four tirerotation Replacing the tires Replace the tires whenthe wear band is visiblethrough the tire treads. When replacing full size tires, never mixradial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the tirepressure decal. Make sure that all tires are thes...

Failure to follow these precautions mayadversely affect the handling of the vehicle, and increase the risk of loss of vehicle control,vehicle rollover and/or personal injury. Tires that are larger or smaller than your vehicle’soriginal tires may also affect the accuracy of yourspeedometer. SNOW TIRE...

• The suspension insulation and bumpers will helpprevent vehicle damage. Do not remove thesecomponents from your vehicle when using snowtires and chains. MOTORCRAFT PART NUMBERS Component 3.8L OHVV6 engine 4.6L SOHCV8 engine 4.6L 4v V8 engine (Mach 1) Air filterelement FA-1611 FA-1634 FA-1634 Fuel f...

scheduled maintenance guide to determine thecorrect service interval. 4 Indicates only approximate dry-fill capacity. Some applications may vary based on cooler size and ifequipped with an in-tank cooler. The amount oftransmission fluid and fluid level should be set bythe indication on the dipstick’...

Item Ford partname Ford partnumber Fordspecification Windshieldwasher fluid MotorcraftPremiumWindshieldWasherConcentrate ZC-32–A WSB-M8B16–A2 1 Add 118 ml (4 oz.) of Additive Friction Modifier XL-3 or equivalent meeting Ford specificationEST-M2C118-A for complete refill of Traction-Lokaxles. Ford de...

VEHICLE DIMENSIONS Vehicledimensions Coupe mm (in) Convertible mm(in) (1) Overall length 4653.3 (183.2) 4653.3 (183.2) (2) Overall width 1856.7 (73.1) 1856.7 (73.1) (3) Overall height 1348.7 (53.1) 1351.3 (53.2) (4) Wheelbase 2573.0 (101.3) 2573.0 (101.3) (5) Track - Front 1534.2 (60.4) 1 1534.2 (60...

FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of genuine Ford accessories areavailable for your vehicle through your localauthorized Ford, Lincoln, Mercury or Ford of Canadadealer. These quality accessories have beenspecifically engineered to fulfill your automotiveneeds; they are custom design...

A Air bag supplementalrestraint system .. 77–78 and child safetyseats ......................... 79description .............. 78disposal .................... 82driver air bag .......... 80indicator light ......... 81operation ................. 80passenger air bag ... 80 Air cleaner filter ..... 199 A...

E Emergencies, roadside jump-starting ........ 129 Emission controlsystem ...................... 185 Engine .............. 204–205 cleaning ................. 148coolant ................... 167idle speedcontrol ................... 164lubrication specifica-tions ............... 202, 204refill capaciti...