Ford 2003 Excursion v.1- Manuals

Event Data Recorder The computer in your vehicle is capable of recording detailed datapotentially including but not limited to information such as: • the use of restraint systems including seat belts by the driver andpassengers, • information about the performance of various systems and modules inth...

Notice to owners of diesel-powered vehicles Read the 7.3 Liter Power Stroke Direct Injection Turbo Diesel Owner’sGuide Supplement for information regarding correct operation andmaintenance of your diesel-powered light truck. Notice to owners of pickup trucks and utility type vehicles Utility vehicle...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat InstallationWarning Child Seat LowerAnchor Child Seat TetherAnchor Brake System Anti-Lock Brake System Brake Fluid -No...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

Brake system warning light: To confirm the brake system warninglight is functional, it willmomentarily illuminate when theignition is turned to the ON position when the engine is not running, orin a position between ON and START, or by applying the parking brakewhen the ignition is turned to the ON ...

Low fuel: Illuminates when the fuel level in the fuel tank is at, or nearempty (refer to Fuel gauge in this chapter). Speed control: Illuminates when the speed control is activated. Turnsoff when the speed control systemis deactivated. Transmission Tow/Haul Feature(if equipped): The ON light on the ...

Engine coolant temperaturegauge: Indicates engine coolant temperature. At normal operatingtemperature, the needle will be inthe normal range (between “H” and“C”). If it enters the red section, the engine is overheating. Stopthe vehicle as soon as safelypossible, switch off the engineand let the engi...

Engine oil pressure gauge: Indicates engine oil pressure. Theneedle should stay in the normaloperating range (between “L” and“H”). If the needle falls below thenormal range, stop the vehicle, turnoff the engine and check the engineoil level. Add oil if needed. If the oillevel is correct, have your v...

Yellow area (warning) — the transmission fluid is higher thannormal operating temperature. Thiscan be caused by special operationconditions (i.e. snowplowing, towingor off road use). Refer to Special Operating Conditions in the scheduled maintenance guide forinstructions. Operating thetransmission f...

PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD 1. Power/volume: Press to turn ON/OFF; turn to increase/decreasevolume. 2. Scan: Press to hear a brief sampling of all listenable stations,tape selections or CD tracks. Pressagain to stop. 3. CD Door: Insert a CD with the label side up. SCAN Entertainment Syst...

6. Bass: Press BASS; then press SEL / to decrease/increase the bass output. Treble: Press TREB; then press SEL / to decrease/increase the treble output. 7. Select: Use with Bass, Treble, Balance and Fade controls to adjustlevels. Use with MENU to set theclock and engage RDS. 8. Balance: Press BAL; t...

17. Disc/Tune: Radio: Press or to manually tune down or up the frequency band. CD: Press or to select the previous or next track on the CD. 18. CD door: Insert a CD label side up. REAR AUDIO CONTROLS (IF EQUIPPED) The rear seat controls allow the middle seat passengers to operate theradio, tape, CD ...

7. Auxiliary jacks Insert lines for standard video game players. 8. STOP/EJECT control Press once to stop DVD play. Press again to eject the DVD. 9. DISPLAY (DISP) control Press to enable on screen display of player menu and user displayadjustments. DVD control features Menu control Press the MENU c...

FWD or REV control for slow motion playback. Three different speedsare available depending on how long the control is held. Press thecontrol once for slow motion playback. Press the control again todisengage slow motion playback. Press the control a third time to returnto normal playback mode. User ...

Rear seat controls The DVD system controls allow therear seat passengers to operate theradio, tape, CD, DVD or CD DJ (ifequipped). Press the / control to activate the rear controls. will appear in the radio display. Adjusting the volume from the rear seat controls The volume control allows the rears...

Liquid Crystal Display (LCD) flip-down screen The screen rotates down to view and up into housing to store when notin use. Be sure the screen is latched into the housing when being stored. 1. 7.0” (diagonal) active matrix liquid crystal display (LCD) screen.2. Screen housing.3. Dimmer switch. Toggle...

General operating tips • When the engine is not running, use the system sparingly otherwise itwill run the battery down. • When the ignition is turned to OFF, the Rear Seat Entertainment DVDSystem is also turned OFF. When the ignition is turned ON, thesystem will begin playback from the last selecte...

If the CD/DVD is not removed within the allotted time, the system willpull the CD/DVD back into the system for safety purposes. If theCD/DVD will not eject from the system, press and hold the EJECTcontrol for approximately 2 seconds. The disc should eject whether thevehicle ignition is ON or OFF. Pl...

6. Subtitles (specific language type - English or Spanish, dependent ofdisc capability and ON/OFF selection.) 7. Camera angle (of picture) - Adjustable with cursor controls andENTER control. Safety information Read all of the safety and operating instructions before operating thesystem and retain fo...

provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance withthe instructions, may cause harmful interference and radiocommunications. However, there is n...

from these fluids could drip down into the internal electronics of thescreen and cause damage. Do not apply excessive pressure whilecleaning the screen. Foreign substances Exercise care to prevent dirt and foreign objects from entering the DVDplayer compartment. Be especially careful not to spill li...

• Tighten very loose tapes by inserting a finger or pencil into the holeand turning the hub. • Remove loose labels before inserting tapes. • Allow tapes which have been subjected to extreme heat, humidity orcold to reach a moderate temperature before playing. • Clean the cassette player head with a ...

MANUAL HEATING AND AIRCONDITIONING SYSTEM 1. Fan speed adjustment: Controls the volume of air circulated in thevehicle. 2. Temperature selection: Controls the temperature of the airflow in the vehicle. 3. Air flow selections: Controls the direction of the airflow in the vehicle. See the following fo...

• To reduce humidity build up inside the vehicle: do not drive with theair flow selector in the OFF or MAX A/C position. • Under normal weather conditions, do not leave the air flow selector inMAX A/C or OFF when the vehicle is parked. This allows the vehicleto “breathe” using the outside air inlet ...

3. Airflow control: FLOOR directs air to the floor of the third row seating. PANEL directs air to the overhead registers of the second andthird row seating. To blend the airflow, select any position betweenPANEL and FLOOR. Rear auxiliary controls: Once the front auxiliary control is set to REAR, the...

HEADLAMP CONTROL Turns the lamps off. Turns on the parking lamps, instrument panel lamps, licenseplate lamps and tail lamps. Turns the headlamps on. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the hea...

Foglamp control (if equipped) The headlamp control also operatesthe foglamps. The foglamps can beturned on only when the headlampcontrol is in the or position and the high beams are notturned on. Pull headlamp control towards youto turn foglamps on. The foglampindicator light will illuminate if the ...

INTERIOR LAMPS Dome/Map lamps (if equipped) The map lamps and controls arelocated on the dome lamp. Press thecontrols on either side of each maplamp to activate the lamps. Rear courtesy/reading lamps • Second row courtesy/reading lamp • Third row courtesy/reading lamp The courtesy lamps light when: ...

Function Number of bulbs Trade number Second row reading lamp 2 578 Third row reading lamp 2 211-2 License lamp 2 168 All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your dealer Interior bulbs Check the operation of all bulbs frequently. Repl...

2. Remove the two screws andcarefully pull the parking lamp/turnsignal assembly from the vehicle. 3. Rotate bulb socketcounterclockwise and remove itfrom lamp assembly. 4. Pull the bulb straight out of thesocket. Install the new bulbs in reverse order. Lights 51

MULTI-FUNCTION LEVER Windshield wiper: Rotate the end of the control away from you toincrease the speed of the wipers;rotate towards you to decrease thespeed of the wipers. Speed dependent wipers: When the wiper control is on, the speed ofthe wipers will automatically adjustwith the vehicle speed. T...

Changing the wiper blades 1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to release the bladeand pull the wiper blade downtoward the windshield to remove itfrom the arm. 2. Attach the new wiper to thewiper arm and press it into pla...

OVERHEAD CONSOLE The appearance of your vehicle’s overhead console will vary according toyour option package. Forward storage bin (if equipped) Press the release control to openthe storage compartment. The doorwill open slightly and can be movedto full open. The storage compartment may beused to sec...

AUXILIARY POWER POINT Power outlets are designed for accessory plugs only. Do not hangany type of accessory or accessory bracket from the plug.Improper use of the power outlet can cause damage not coveredby your warranty. The power point is an additional power source for electrical accessories. Do n...

Power side view mirrors (if equipped) To adjust your mirrors 1. Select L to adjust the left mirror or R to adjust the right mirror. 2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the center position todisable the adjust function. Heated outside mirrors (if equipped) Bo...

Fold-away mirrors Fold the side mirrors in carefully when driving through a narrow space,like an automatic car wash. The telescoping feature (if equipped) allows the mirror to extendapproximately 76 mm (3 inches). This feature is especially useful to thedriver when towing a trailer. POWER ADJUSTABLE...

Do not use the speed control in heavy traffic or on roads thatare winding, slippery or unpaved. Setting speed control The controls for using your speedcontrol are located on the steeringwheel for your convenience. 1. Press the ON control and releaseit. 2. Accelerate to the desired speed. 3. Press th...

• Press the speed control OFFcontrol. Note: When you turn off the speed control or the ignition, your speedcontrol set speed memory is erased. Indicator light This light comes on when either theSET ACCEL or RES controls arepressed. The vehicle speed must beat or above 48 km/h (30 mph). Itturns off w...

TRIP COMPUTER (IF EQUIPPED) The trip computer tells you about the condition of your vehicle througha constant monitor of vehicle systems. You may select display features onthe trip computer for a display of status. The appearance of your vehicle’s trip computer may differ depending onyour vehicle’s ...

Compass The compass display is contained in the overhead console. The vehicleheading is displayed as one of N, NE, E, SE, S, SW, W and NW.The compass heading is displayed in average fuel economy modes, fuelrange modes and temperature modes.The compass reading may be affected when you drive near larg...

For optimum calibration, turn off all electrical accessories (heater/airconditioning, wipers, etc.) and make sure all vehicle doors are shut. 1. Locate the trip computer located in the overhead console. 2. Start the vehicle. 3. Press and hold both tripcomputer controls. Afterapproximately eight seco...

purchase). It is also suggested that upon the sale of the vehicle, theprogrammed Homelink 威 Universal Transceiver buttons be erased for security purposes, refer to Programming in this section. Programming Do not program the HomeLink 威 Universal Transceiver with the vehicle parked in the garage. Note...

device should activate when the HomeLink 威 button is pressed and released. Note: To program the remaining two HomeLink 威 buttons, begin with step 2 in the “Programming” section — do not repeat step 1. If the red light blinks rapidly for two seconds and then turns to acontinuous red, proceed with ste...

• Proceed with step 4 in the “Programming” section. Operating the HomeLink 姞 Universal Transceiver To operate, simply press and releasethe appropriate HomeLink 威 button. Activation will now occur for thetrained product (garage door, gateoperator, security system, entrydoor lock, or home or office li...

• To open the liftgate, unlock theliftgate (with the key, the key fobby pressing the UNLOCK buttontwice or power door locks) andpull up on the liftgate handle. • To open the cargo doors, openthe liftgate, then open right cargodoor first, using the handle ontop of the door, then open theleft cargo do...

KEYS The key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer. You should always carry a second key with you in a safe place in caseyou require it in an emergency. Refer to SecuriLock 娂 Passive Anti-Theft System for more information. POWER DOOR LOCK...

• the ignition is turned to the ON position, or • using the UNLOCK control on your remote entry transmitter. Power door unlock disable feature — activation/deactivation Please see your dealer in order to activate/deactivate this feature. Sounding a panic alarm Press to activate the alarm. Press agai...

transmitters, you can either reprogram them yourself, or take all remote entry transmitters to your authorized dealer for reprogramming. How to reprogram your remote entry transmitters You must have all remote entry transmitters (maximum of four) available before beginning this procedure. To reprogr...

Erasing personal code 1. Enter the factory set 5–digit code. 2. Press and hold the 1 • 2 for two seconds. This must be done within five seconds of completing step 1. 3. Press the 7 • 8 and the 9 • 0 at the same time. This must be done within five seconds of completing step 2. Your personal code is n...

Your vehicle comes with two coded keys; additional coded keys may bepurchased from your dealer. The dealer can program your spare keys toyour vehicle or you can program the keys yourself. Refer to Programming spare keys for instructions on how to program the coded key. Note: The SecuriLock 娂 passive...

Replacing coded keys can be very costly. Store an extra programmed keyaway from the vehicle in a safe place to help prevent anyinconveniences. Please visit an authorized dealer to purchase additionalspare or replacement keys. Programming spare keys You can program your own coded keys to your vehicle...

8. Remove the previously programmed coded key from the ignition. 9. Within twenty seconds of removing the previously programmed codedkey, insert the unprogrammed key (new/valet key) into the ignition. 10. Turn the ignition from the 1 (OFF) position to the 3 (ON) position.Keep the ignition in the 3 (...

SEATING Notes: Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in the event of a collision. Do not pile cargo higher than the seatbacks to reduce the risk ofinjury in a collision or sudden stop. Full bench seat (if equipped) • ...

Memory seats, adjustable pedals, and mirrors (if equipped) This system allows automaticpositioning of the driver seat,adustable pedals, and outsiderearview mirrors to twoprogrammable positions. The memory seat control is locatedon the driver door. • To program position one, movethe driver seat to th...

Adjusting the front power seat (if equipped) The control is located on the outboard side of the seat cushion. Press to raise or lower the frontportion of the seat cushion. Press to raise or lower the rearportion of the seat cushion. Press the control to move the seatforward, backward, up or down. Se...

To gain access to the storagecompartment in your armrest, liftthe latch to open the lid. The lidcannot be opened in the uprightposition. REAR SEATS Head restraints To properly adjust your headrestraints, lift the head restraint sothat it is located directly behindyour head or as close to thatpositio...

Reclining the second row seatback Locate the release handle located onthe outboard side of the seatcushion and lift gently to allow theseatback to be adjusted to thedesired location. Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injur...

SAFETY RESTRAINTSSafety restraints precautions Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. To reduce the risk of injury, make sure children sit where theycan be properly restrained. Never let a passenger hold a child on his or her lap while thevehic...

When to use the automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to remove any slack in the shoulder belt. The automaticlocking mode is not available on the driver safety belt. This mode should be used any time a child safety seat is inst...

In the event of a collision, thecolored label (REPLACE BELT)may become visible. If this occurs, the safety belt must be replaced. Whenever the yellowportion of the label is visible, the safety belt must bereplaced. Failure to follow theseinstructions will affect the performance of the safety beltsan...

Position the safety belt height adjusters so that the belt restsacross the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt andincrease the risk of injury in a collision. Lap belts Adjusting the lap belt The lap belt should fit snugl...

Reasons given... Consider... “I was in a hurry” Prime time for an accident. BeltMinder reminds us to take a fewseconds to buckle up. “Seat belts don’t work” Safety belts, when used properly, reduce risk of death to front seat occupants by 45% in cars, and by 60% in light trucks. “Traffic is light” N...

8. Confirmation of enabling BeltMinder is provided by flashing the safetybelt warning light four times per second for three seconds, followed bythree seconds with the safety belt warning light off, then followed byflashing the safety belt warning light four times per second for threeseconds again. 9...

AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Important SRS precautions The SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body injuries. Airbags DO NOT inflate slowly; there isa risk of injury from a deploying airbag. All occupants of...

Children and air bags Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating position. Failure to followthese instructions may increase therisk of injury in a collision. Air bags can...

Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone toindicate the condition of the system. Refer to Air bag readiness section in the Instrument cluster chapter. Routine maintenance of the air bag is not required. A difficulty with the system i...

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant orchild restraint you might use. Children and safety belts If the child is the pro...

Booster seats should be used until you can answer YES to ALL of thesequestions: • Can the child sit all the way backagainst the vehicle seat back withknees bent comfortably at theedge of the seat withoutslouching? • Does the lap belt rest low across the hips? • Is the shoulder belt centered on the s...

The shoulder belt should cross the chest, resting snugly on the center ofthe shoulder. The lap belt should rest low and snug across the hips,never up high across the stomach. If the booster seat slides on the vehicle seat, placing a rubberized meshsold as shelf or carpet liner under the booster seat...

Installing child safety seats with combination lap and shoulderbelts Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all theway back. Children 12 and ...

7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with your knee on thechild seat. 8. Allow the safety belt to retract toremove any slack in the belt. 9. Before placing the child in theseat, forcibly move the seat forwardand back to...

STARTING Positions of the ignition 1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 2. LOCK, locks the steering wheel,automatic transmission gearshiftlever and allows key removal. 3. OFF, shuts off the engine and allaccessories without lockin...

Starting the engine 1. Turn the key to 4 (ON) withoutturning the key to 5 (START). 2. Turn the key to 5 (START), thenrelease the key as soon as theengine starts. Excessive crankingcould damage the starter. Note: If the engine does not start within five seconds on the first try, turn the key to 3 (OF...

Important ventilating information If the engine is idling while the vehicle is stopped for a long period oftime, open the windows at least 2.5 cm (one inch) or adjust the heatingor air conditioning to bring in fresh air. BRAKES Occasional brake noise is normal. If a metal-to-metal, continuous grindi...

Parking brake To set the parking brake, press theparking brake pedal down until thepedal stops. The BRAKE warninglamp in the instrument clusterilluminates and remains illuminateduntil the parking brake is released. To release the brake, pull therelease lever. to prevent the pedalfrom releasing too q...

Loaded vehicles, with a higher center of gravity, may handledifferently than unloaded vehicles. Extra precautions, such as slower speeds and increased stopping distance, should be taken whendriving a heavily loaded vehicle. AUTOMATIC TRANSMISSION OPERATION Brake-shift interlock This vehicle is equip...

by pressing the transmission control switch on the end of the gearshiftlever. This will illuminate the O/D OFF lamp and activate Drive. Drive (not shown) Drive is activated when the transmission control switch is pressed. • This position allows for all forward gears except overdrive. • O/D OFF lamp ...

an adaptive learning strategy. The adaptive learning strategy ismaintained by power from the battery. When the battery is disconnectedor a new battery is installed, the transmission must relearn its adaptivestrategy. Optimal shifting will resume within a few hundred kilometers(miles) of operation. I...

indicator light on the control will illuminate when the system is turnedoff. If the indicator light illuminates when the RSS is not turned off, itmay indicate a failure in the RSS. Keep the RSS sensors (located on the rear bumper/fascia) freefrom snow, ice and large accumulations of dirt (do not cle...

Front wheel hub locks (if equipped) Engage or disengage the 4WD system by: • rotating the control for both front wheel hub locks from the FREE orLOCK position, then • manually engage or disengage the transfer case with the floor-mountedshifter For increased fuel economy in 2WD, rotate both hub locks...

4X4 HIGH (4WD High) - Used for extra traction such as in snow or icy roads or in off-road situations. Not intended for use on dry pavement. 4X4 LOW (4WD Low) - Uses extra gearing to provide maximum power to all four wheels. Intended only for off-road applications such as deepsand, steep grades or pu...

Drive cautiously to avoid vehicle damage from concealed objects such asrocks and stumps. You should either know the terrain or examine maps of the area beforedriving. Map out your route before driving in the area. To maintainsteering and braking control of your vehicle, you must have all fourwheels ...

Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any morethan low-slung sports cars are desig...

sounds. This is the front drivetrain coming up to speed and theautomatic locking hubs engaging and is not cause for concern. Sand When driving over sand, try to keep all four wheels on the most solidarea of the trail. Avoid reducing the tire pressures but shift to a lowergear and drive steadily thro...

After driving through mud, clean off residue stuck to rotating driveshaftsand tires. Excess mud stuck on tires and rotating driveshafts causes animbalance that could damage drive components. “Tread Lightly” is an educationalprogram designed to increase publicawareness of land-use regulationsand resp...

Never drive with chains on the front tires of 4WD vehicles without alsoputting them on the rear tires. This could cause the rear to slide andswing around during braking. Tires, Replacement Requirements Do not use a size and type of tire and wheel other than thatoriginally provided by Ford Motor Comp...

Each day before you drive, checkyour tires. If one looks lower thanthe others, use a tire gauge to checkpressure of all tires, and adjust ifrequired. Check tire pressure with atire gauge every few weeks(including spare). Safe operationrequires tires that are neitherunderinflated nor a vehicle which ...

Calculating the load your vehicle can carry/tow 1. Use the appropriate maximum GCWR chart (in the Trailer Towing section in this chapter) for your type of engine and rear axle ratio. 2. Weigh your vehicle without cargo. To obtain correct weights, take yourvehicle to a shipping company or an inspecti...

Note: Adjusting an equalizing hitch so the rear bumper of the vehicle is higher than it was unloaded will defeat the function of the loadequalizing hitch and may cause unpredictable handling. Safety chains Always connect the trailer’s safety chains to the frame or hook retainersof the vehicle hitch....

Driving while you tow When towing a trailer: • Turn off the speed control. The speed control may shut offautomatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer. • To eliminate excessive shifting, use a lower gear. This will ...

• Do not allow waves to break higher than 15 cm (6 inches) above thebottom edge of the rear bumper. • Disconnect the trailer tow electrical connector to prevent blown fusescaused by water entering into your trailer’s electrical wiring. Exceeding these limits may allow water to enter critical vehicle...

GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the New Vehicle Limited...

Canadian customers who require roadside assistance, call1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford MotorCompany will reimburse a reasonable amount. To obtain reimbursementinformation, U.S. Ford or Mercury vehicles customers call1-800-241-3673; Lincoln vehicle custo...

This switch is located in the frontpassenger’s footwell, by the kickpanel access cover. To reset the switch: 1. Turn the ignition OFF. 2. Check the fuel system for leaks. 3. If no leaks are apparent, reset theswitch by pushing in on the resetbutton. 4. Turn the ignition ON. 5. Wait a few seconds and...

Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

If your vehicle is equipped with a tire pressure monitoringsystem, refer to Tire Pressure Monitoring System (if equipped) in the Maintenance and specifications section for important informationbefore changing your tires. If the tire pressure monitoring systembecomes damaged, it will no longer functi...

1. Park on a level surface, activatehazard flashers and set the parkingbrake. 2. Turn engine OFF and block thediagonally opposite wheel (block notprovided). 3. Remove the jack, jack handle, lugwrench and spare tire from thestowage locations. 4. Use the tip of the lug wrench to remove any wheel trim....

6. Insert the hooked end of the jackhandle into the jack and use thehandle to slide the jack under thevehicle. 7. Position the jack according to the following guides: • Front (4x2) • Front passenger side (4x4) • Front driver side (4x4) Make sure the jack fits into thenotched area on the differential...

• Rear 8. Turn the jack handle clockwiseuntil the wheel is completely off theground and high enough to installthe spare tire. To lessen the risk ofpersonal injury, do not put any part of your body under thevehicle while changing a tire. Donot start the engine when yourvehicle is on the jack. The jac...

Bolt size Wheel lug nut torque* Nm Lb-ft M14 x 1.5 200-225 150-165 * Torque specifications are for nut and bolt threads free of dirt andrust. Use only Ford recommended replacement fasteners. On all two-piece flat wheel nuts,apply one drop of motor oil betweenthe flat washer and the nut. Do notapply ...

1. Use only a 12–volt supply to start your vehicle. 2. Do not disconnect the battery of the disabled vehicle as this coulddamage the vehicle’s electrical system. 3. Park the booster vehicle close to the hood of the disabled vehiclemaking sure the two vehicles do not touch. Set the parking brake on b...

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second ...

Removing the jumper cables Remove the jumper cables in the reverse order that they wereconnected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Remove the jumper cable on the negative (...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member, your roadside assistance center. On 4x2 vehicles, it is acceptable to tow the vehicle with the front wheelson the ground and the rear wheels off the ground using a wheel lift or aslin...

GETTING THE SERVICES YOU NEED At home Ford Motor Company and Ford of Canada have authorized dealerships toservice your vehicle. It is preferred that you return to the authorizeddealer where your vehicle was purchased when warranty repairs areneeded. However, you may also take your vehicle to another...

In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action un...

• available free to owners and lessees of qualifying Ford Motor Companyvehicles. The Dispute Settlement Board may not be available in all states. FordMotor Company reserves the right to change eligibility limitations, modifyprocedures and/or to discontinue this service without notice and withoutincu...

before the Board, this is not a requirement and the Board will decide thecase whether or not an oral presentation is made. An oral presentationmay be requested by the Board as well. Making a decision Board members review all available information related to eachcomplaint, including oral presentation...

The CAMVAP program is a straight-forward and relatively speedyalternative to resolve a disagreement when all other efforts to produce asettlement have failed. This procedure is without cost to you and isdesigned to eliminate the need for lengthy and expensive legalproceedings. In the CAMVAP program,...

WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is availablefrom your dealer. • Never use strong household detergents or soap, such as dish washingor laundry liquid. These products can discolor and s...

PAINT CHIPS Your dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jam) toyour dealer to ensure you get the correct color. • Remove particles such as bird droppings, tree sap, insect deposits, tarspots, road salt and in...

• Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage. PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products areavailable from your dealer. • For routine cleaning, use Motorcraft Detail Wash (ZC-3–A...

• Avoid cleaners or polish that increase the gloss of the upper portion ofthe instrument panel. The dull finish in this area helps protect thedriver from undesirable windshield reflection. Do not use chemical solvents or strong detergents when cleaningthe steering wheel or instrument panel to avoid ...

• To help maintain its resiliency and color, use the Motorcraft DeluxeLeather Care Kit (ZC-11–D), available from your authorized dealer. • Do not use household cleaning products, alcohol solutions, solvents orcleaners intended for rubber, vinyl and plastics, or oil/petroleum-basedleather conditioner...

Motorcraft Detail Wash (ZC-3–A) Motorcraft Tire Detailer (ZC-28) Motorcraft Triple Clean (ZC-13) Motorcraft Ultra-Clear Spray Glass Cleaner (not available in Canada)(ZC-23) Motorcraft Engine Shampoo and Degreaser (ZC-20) * May be sold with the Motorcraft name Cleaning 188

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a scheduled maintenance guide which makes trackingroutine service easy. If your vehicle requires professional service, your dealership can providethe...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel. 2. Go to the front of the vehicle andrelease the auxiliary latch locatedunder the right center of the hood.Slide the handle to release theauxiliary latch. 3. Lift the hood ...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 5.4L V8/6.8L V10 gasoline engines Refer to the 7.3 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement for diesel engine component locations. 1. Battery 2. Engine oil filler cap 3. Transmission fluid dipstick 4. Engine oil dipsti...

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely. Only use a washer fluid that meetsFord specification WSB-M8B16–A2.Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic c...

4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove theengine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is between the MIN and MAX marks, the oil level is acceptable. DO NOT ADD OIL...

3. Recheck the engine oil level. Make sure the oil level is not above theMAX mark on the engine oil level indicator (dipstick). 4. Install the indicator and ensure it is fully seated. 5. Fully install the engine oil filler cap by turning the filler cap clockwise1/4 of a turn until three clicks are h...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. However, for severe usage or in high temperature climates, check thebattery electrolyte level. Refer to the scheduled maintenance guide forthe service ...

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.Lift the battery with a battery carrier or with your hands on oppositecorners. Keep batteries out of reach of ...

If the battery has been disconnected or a new battery has been installed,the clock and radio settings must be reset once the battery isreconnected. • Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling ...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “cold fill level” or within the “coldfill range” as listed on the engine coolant reservoir (depending uponapplication). • Refer to the Scheduled Maintenance Guide for service interval...

Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. The cooling system in your vehicle is filled with either green-coloredMotorcraft Premium Engine Coolant meeting Ford specificationESE...

Recycled engine coolant Ford Motor Company recommends the use of a recycled engine coolantproduced by Ford-approved processes in vehicles originally equippedwith Motorcraft Premium Engine Coolant (green-colored). However, notall coolant recycling processes produce coolant that meets Fordspecificatio...

Once the engine temperature cools, the engine can be re-started. Takeyour vehicle to a service facility as soon as possible to minimize enginedamage. When fail-safe mode is activated You have limited engine power when in the fail-safe mode, so drive thevehicle with caution. The vehicle will not be a...

When refueling always shut the engine off and never allowsparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions.Care should be taken to avoid inhaling excess fumes. The flow of fuel through a fuel pump nozzle can produce st...

in the United States) because it may cause these problems to becomemore pronounced. If the problems persist, see your dealer or a qualifiedservice technician. It should not be necessary to add any aftermarket products to your fueltank if you continue to use high quality fuel of the recommended octan...

• Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in kilometers or miles). 2. Each time you fill the tank, record ...

• Four-wheel-drive operation (if equipped) is less fuel efficient thantwo-wheel-drive operation. • Close windows for high speed driving. EPA window sticker Every new vehicle should have the EPA window sticker. Contact yourdealer if the window sticker is not supplied with your vehicle. The EPAwindow ...

TRANSMISSION FLUID Checking automatic transmission fluid (if equipped) Refer to your scheduled maintenance guide for scheduled intervals forfluid checks and changes. Your transmission does not consume fluid.However, the fluid level should be checked if the transmission is notworking properly, i.e., ...

If an overfill occurs, excess fluidshould be removed by a qualifiedtechnician. An overfill condition oftransmission fluid may causeshift and/or engagementconcerns and/or possibledamage. Do not use supplemental transmission fluid additives, treatments orcleaning agents. The use of these materials may...

Use only fluid that meets Ford specifications. Refer to Lubricant Specifications in this chapter. AIR FILTER MAINTENANCE Refer to the scheduled maintenance guide for the appropriate intervalsfor changing the air filter element. When changing the air filter element, use only the Motorcraft air filter...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B and C, representing the tire’sresistance to the gene...

• Four tire rotation • Five tire rotation Replacing the tires Replace the tires when the wearband is visible through the tiretreads. Due to exposure to theelements and exhaust you shouldreplace the spare tire when youreplace the other tires. Maintenance and Specifications 220

When replacing full size tires, never mix radial bias-belted, orbias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same size, speedrating, and load-carrying capacity. Use only the tire combinationsrecommended on the label. If you do ...

• If possible, avoid fully loading your vehicle. • Remove the tire chains when they are no longer needed. Do not usetire chains on dry roads. • The suspension insulation and bumpers will help prevent vehicledamage. Do not remove these components from your vehicle whenusing snow tires and chains. MOT...

LUBRICANT SPECIFICATIONS Item Ford partname orequivalent Ford partnumber Fordspecification Spindle bearing HighTemperature4X4 Front Axleand WheelBearing Grease E8TZ-19590–A ESA-M1C198–A Front axle Hypoid Gear OilSAE 90 C6AZ-19580–E ESW-M2C105–A Rear axle 1 Motorcraft SAE75W-140 HighPerformanceSynthe...

Item Ford partname orequivalent Ford partnumber Fordspecification Engineoil-Gasolineengines Motorcraft SAE5W-20 PremiumSynthetic BlendMotor Oil XO-5W20-QSP WSS-M2C153-Hand APICertificationMark Engine oil-Dieselengine Refer to your 7.3L Diesel Supplement Hinges, latches,striker plates,fuel filler doo...

1 Add 236 ml (8 oz.) of Additive Friction Modifier XL-3 or equivalent meeting Ford specification EST-M2C118-A for complete refill ofTraction-Lok axles. Ford design rear axles contain a synthetic lubricantthat does not require changing unless the axle has been submerged inwater. 2 Ensure the correct ...

Vehicle identification number (VIN) The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Please note thatin the graphic XXXX isrepresentative of your vehicleidentification number.) 1. World manufacturer identifier 2. Brake type and gross vehi...

FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of genuine Ford accessories are available for yourvehicle through your local authorized Ford, Lincoln, Mercury or Ford ofCanada dealer. These quality accessories have been specificallyengineered to fulfill your automotive needs; they are custom desi...

A Accessory delay ..........................59 Air bag supplementalrestraint system ........................109 and child safety seats ............111description ..............................109disposal ....................................113driver air bag ..........................111indicator lig...

Exhaust fumes ..........................127 F Fail safe cooling ........................202 Fluid capacities .........................222 Foglamps .....................................46 Four-Wheel Drive vehicles .......136 driving off road .......................138electronic shift ...................