Ford 2002 Taurus v.1- Manuals

This Owner’s Guide describes every option and model variantavailable and therefore some of the items covered may not apply to your particular vehicle. Furthermore, due to printing cycles it maydescribe options before they are generally available. Remember to pass on the Owner’s Guide when reselling ...

BREAKING-IN YOUR VEHICLE There are no particular guidelines for breaking-in your vehicle. Duringthe first 1 600 km (1 000 miles) of driving, vary speeds frequently. This isrecommended to give the moving parts a chance to break in. SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty in...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat InstallationWarning Child Seat TetherAnchorage Brake System Anti-Lock Brake System Brake Fluid -Non-Petroleum Based Tr...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

These temporary malfunctions can be corrected by filling the fuel tankwith high quality fuel of the recommended octane and/or properlyinstalling and securely tightening the fuel cap. After three driving cycleswithout these or any other temporary malfunctions present, thelight should turn off. (A dri...

Brake system warning Illuminates if the parking brake isengaged. Also momentarilyilluminates at start up to ensure thecircuit is functional. If the brakewarning lamp does not illuminate atthese times, or illuminates after releasing the parking brake, seek serviceimmediately. Refer to Brakes in the D...

Engine oil pressure Illuminates when the oil pressurefalls below the normal range. Checkthe oil level and add oil if needed.Refer to Engine oil in the Maintenance and specifications chapter. Low coolant (if equipped) Illuminates when the coolant level inthe coolant reservoir is low andmore needs to ...

Check transaxle Illuminates when a transaxleproblem has been detected andshifting may be restricted. If thislamp remains on, have your vehicleserviced immediately. Turn signals Illuminates when the turn signals orthe hazard lights are turned on. Ifthe lights stay on continuously orflash faster, chec...

BeltMinder chime Sounds intermittently to remind you to fasten your safety belts. Supplemental restraint system (SRS) warning chime Sounds when a malfunction in the supplemental restraint system (frontor side airbags) has been detected. Have the supplemental restraintsystem inspected immediately. He...

GAUGES Engine coolant temperature gauge Indicates the temperature of theengine coolant. At normal operatingtemperature, the needle remainswithin the normal area (the areabetween the “H” and “C”). If itenters the red section, the engine isoverheating. Stop the vehicle assoon as safely possible, switc...

Fuel gauge Displays approximately how muchfuel is in the fuel tank. The fuelgauge may vary slightly when thevehicle is in motion or on a grade. When refueling the vehicle fromempty indication, the amount of fuelthat can be added will be less thanthe advertised capacity due to thereserve fuel. Speedo...

AM/FM STEREO Volume/power control Press the control to turn the audiosystem on or off. Turn control to raise or lowervolume. Entertainment Systems 19

If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition switch is turned back on. If you wish to maintain your presetvolume level, turn the audio system off with the power control beforeswitching off the i...

AM/FM select The AM/FM select control works inradio mode. Press the AM or FMcontrol to enter radio mode. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press thecontrol to switch between AM, FM1 or FM2 memory preset stations. Pressing the AM or FM controls whe...

Setting the clock To set the hour, press and hold thehour (H) control. When the desiredhour appears, release the control. To set the minute, press and holdthe minute (M) control. When thedesired minute appears, release thecontrol. Your vehicle is equipped with a special feature that allows you to ac...

MACH T AUDIO SYSTEM WITH AM/FM STEREO/CASSETTE Volume/power control Press the control to turn the audiosystem on or off. Turn control to raise or lowervolume. Entertainment Systems 23

Seek function in CD mode • Press to seek to the previous track of the current disc. If a selection has been playing for three seconds or more and youpress , the CD changer will replay that selection from the beginning. • Press to seek forward to the next track of the current disc. After the last tra...

AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press thecontrol to switch between AM, FM1 or FM2 memory preset stations. Pressing the AM or FM controls when the ignition is turned on will alsoengage the radio. AM/FM select in tape mode Press this control to st...

Setting the clock To set the hour, press and hold thehour (H) control. When the desiredhour appears, release the control. To set the minute, press and holdthe minute (M) control. When thedesired minute appears, release thecontrol. Your vehicle is equipped with a special feature that allows you to ac...

AUDIO SYSTEM WITH AM/FM STEREO/SINGLE CD PLAYER Volume/power control Press the control to turn the audiosystem on or off. Turn control to raise or lowervolume. Entertainment Systems 30

Setting memory preset stations 1. Select the frequency band withthe AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns,indicating the station is held in memory...

Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to movethrough the frequencies quickly. • Press to move to the next frequency up the band (whether or not a listenable station is located there). Hol...

2. Press to eject the magazine. 3. Turn the magazine (A) over. 4. Using the disc holder releaseknob (C), pull the disc holder (B)out of the magazine. If you pull too hard on the disc holder, the disc holder may comecompletely out of the magazine. If this happens, reinsert the disc holderback into th...

5. Line up the CD with the grooveof the disc holder. Ensure that thelabel on the CD faces downwards. 6. Press in on the disc holder until itlocks securely into the magazine. Ifthe disc holders are not fully lockedinto the magazine, the unit will notoperate. Ensure that the disc holder isevenly inser...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) Fan speed control Controls the volume of air circulatedin the vehicle. Temperature control knob Controls the temperature of theairflow inside the vehicle. Mode Selector Control Controls the direction of the airflowto the inside of the vehicle. ...

• (Defrost) – Distributes outside air through the windshield defroster ducts. It can be used to clear ice or fog from the windshield.If the temperature is about 6°C (43°F) or higher, the air conditionerwill automatically dehumidify the air to reduce fogging. Operating tips • In humid weather conditi...

Turning the EATC on Press AUTO, any of the override controls or the fan speed control. TheEATC will only operate when the vehicle is running. Turning the EATC system off Press OFF. The outside temperaturefunction will continue to operateuntil the ignition is turned off. Automatic operation Press AUT...

Temperature selection The display window indicates theselected temperature, function(AUTO or one of the overridecontrols) and manual control of fanspeed ( ) if automatic fan speed is not desired. To control the temperature, selectany temperature between 18°C(65°F) and 29°C (85°F) by pressingthe temp...

Temperature conversion Press MAX A/C and F at the same time (until the display changes) to switch between Fahrenheit and Celsius. Fan speed ( ) When AUTO is pressed, fan speed isadjusted automatically for existingconditions. You can override fanspeed at any time. To control fanspeed manually, press ...

Manual override controls The override controls are located at the bottom of the EATC and allowyou to determine where airflow is directed. To return to full automaticcontrol, press AUTO. The air conditioning compressor can operate in all modes except . It will also operate only when required when AUT...

• (Floor)-Distributes outside air through the floor ducts. Heating and air conditioning capabilities are provided in this mode. The air willbe heated or cooled based on temperature selection. • (Panel and floor) -Distributes outside air through the instrument panel registers and the floor ducts. Hea...

Operating tips • In humid weather conditions, place the climate control system inF before driving. This will reduce fogging on your windshield. Once the windshield has been cleared, operate the climate controlsystem as desired. • To reduce humidity buildup inside the vehicle in cold weathercondition...

REAR WINDOW DEFROSTER The rear defroster control is locatedon the instrument panel. Press the rear defroster control toclear the rear window of thin iceand fog. • A small LED will illuminate whenthe rear defroster is activated. The ignition must be in the ON position to operate the rear windowdefros...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parkinglamps. Rotate to the second positionto turn on the headlamps. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the he...

High beams • Push forward to activate. • Pull toward you to deactivate. Flash to pass Pull toward you to activate andrelease to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of theinstrument panel during headlampand parklamp operation. • Rotate up to brighten. • Rotate down to dim. •...

Vertical aim adjustment 1. Park the vehicle on a level surface approximately 7.6 meters (25 feet)from a vertical wall or screen directly in front of it. • (A) Eight feet • (B) Center height of lamp to ground • (C) Twenty five feet • (D) Horizontal reference line 2. Measure the height of the headlamp...

Replacing headlamp bulbs To remove the headlamp bulb: 1. Make sure headlamp switch is inOFF position. 2. Remove the bolt from theheadlamp housing. 3. At the back of the headlamp, pryup and remove the two retainer pinsto release the headlamp assemblyfrom the vehicle and pull headlampforward. 4. Remov...

5. Disconnect the electricalconnector from the bulb by pullingrearward. 6. Remove the bulb retaining ring byrotating it counterclockwise. 7. Remove the old bulb from thelamp assembly by pulling it straightout of the lamp assembly. To install the new bulb: Handle a halogen headlamp bulb carefully and...

2. Install the bulb retaining ring over the plastic base and lock the ringby rotating clockwise until it snaps into place. 3. Connect the electrical connector to the bulb. 4. Install the protective dust shield and lock the shield by rotating itclockwise until it locks into position. 5. Carefully pos...

5. Carefully pull bulb straight out ofthe socket and push in the newbulb. 6. Install the bulb socket into thelamp assembly by rotating itclockwise. 7. Carefully position the headlampassembly onto the vehicle. 8. Hold the headlamp assemblysnugly against the vehicle and installthe retainer pins straig...

Replacing high-mount brakelamp bulbs — Wagon only 1. Open liftgate. 2. Remove two screw covers, screwsand handle from liftgate. 3. Remove two screws and the lowertrim panel from the liftgate. 4. Remove the upper trim panel. 5. Remove the rubber plug from thelower access hole in the upperportion of t...

7. Carefully lift the lamp assemblyaway from the liftgate. 8. Remove the bulb socket byrotating it counterclockwise andpulling it out from the lampassembly. 9. Carefully pull the bulb straightout of the socket and push in thenew bulb. 10. To complete installation, followthe removal procedure in reve...

WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper controlto the desired interval, low or highspeed position. The bars of varying length are forintermittent wipers. When in thisposition rotate the control upwardfor fast intervals and downward forslow intervals. Push the control on the end ...

Press the washer control to activatethe rear washer. The wiper willcome on when the washer control ispressed, if it is not already on. Windshield wiper blades Check the wiper blades at least twice a year or when they seem lesseffective. Substances such as tree sap and some hot wax treatments usedby ...

Rear window wiper blades Refer to Windshield wiper blades in this section for more information on rear wiper blades. TILT STEERING Pull the tilt steering control towardyou to move the steering wheel upor down. Hold the control whileadjusting the wheel to the desiredposition, then release the control...

AUXILIARY POWER POINT Power outlets are designed for accessory plugs only. Do not hangany type of accessory or accessory bracket from the plug.Improper use of the power outlet can cause damage not coveredby your warranty. The auxiliary power point is located on the instrument panel below thecigarett...

MIRRORS Automatic dimming inside rear view mirror (if equipped) Your vehicle is equipped with aninside rear view mirror which has anauto-dimming function. Theelectronic day/night mirror willchange from the normal state to thenon-glare state when bright lights(glare) reach the mirror. When the mirror...

Compass zone adjustment 1. Determine which compass zoneyou are in by referring to the zonemap. 2. With the compass display turnedon, press and hold the COMP side ofthe control for no more than fiveseconds until the zone selectionnumber appears in the mirrordisplay window. If a “C” appears, see Compa...

Compass calibration adjustment Perform this adjustment in an open area free from steel structures andhigh voltage lines. 1. Start the vehicle. 2. Press and hold the COMP side ofthe control for approximately sixseconds until “C” appears in themirror display. 3. Drive the vehicle slowly (lessthan 5 km...

Heated outside mirrors (if equipped) Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated. Do not remove ice from the mirrorswith a scraper or attempt toreadjust the mirror glass if it isfrozen in place. These actions couldcause damage to the glass...

SPEED CONTROL (IF EQUIPPED) To turn speed control on • Press ON. Vehicle speed cannot be controlleduntil the vehicle is traveling at orabove 48 km/h (30 mph). Do not shift the gearshift leverinto N (Neutral) with the speedcontrol on. Do not use the speed control in heavy traffic or on roads thatare ...

To set a lower set speed • Press and hold CST −. Releasethe control when the desiredspeed is reached or • Press and release CST − tooperate the Tap-Down function.Each press will decrease the setspeed by 1.6 km/h (1 mph) or • Depress the brake pedal. Whenthe desired vehicle speed isreached, press SET...

Indicator light This light comes on when either theSET or RES controls are pressed. Itturns off when the speed controlOFF control is pressed, the brake is applied or the ignition is turned tothe OFF position. MOON ROOF (IF EQUIPPED) Push up on the control to raise themoon roof to the vent position. ...

To avoid potential distraction and increased risk of injury oraccident, Ford recommends you do not use the phone while driving. Please pull off the road and park before making or answering a call. To prevent damage to the antenna or your car, remove the cellular phoneantenna mast before using an aut...

Rewinding the shade With extended use, the cargo shade may lose its spring tension. If thisoccurs, the shade must be manually rewound. This is a two-personoperation. 1. Remove the shade from the vehicle and extend it with the smoothgrain facing you. 2. Wrap the vinyl around the rollertube twice. Tuc...

Cargo utility hooks (Sedan) The utility hooks located in side the trunk can be used to attach a cargonet to secure lightweight objects or hang small items on. Do not hangmore than 12 kg (20 lbs) on the hooks. The hooks are not designed torestrain objects during a collision. LUGGAGE RACK (IF EQUIPPED...

KEYS The key operates all locks on yourvehicle. In case of loss, replacementkeys are available from your dealer. You should always carry a secondkey with you in a safe place in caseyou require it in an emergency. Refer to SecuriLock y Passive Anti-Theft System for more information. POWER DOOR LOCKS ...

INTERIOR LUGGAGE COMPARTMENT RELEASE Your vehicle is equipped with a mechanical interior luggage compartmentrelease handle that provides a means of escape for children and adults inthe event they become locked inside the luggage compartment. Adults are advised to familiarize themselves with the oper...

REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RS-210 ofIndustry Canada. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) This devicemust accept any interference received, including interfe...

Programming remote transmitters It is necessary to have all (maximum of four — original and/or new) of your remote transmitters available prior to beginning this procedure. To program the transmitters yourself: • Place the key in the ignition andturn from 2 (LOCK) to 3 (OFF)and cycle between 3 (OFF)...

Perimeter lamps illuminated entry The exterior lamps illuminate when the vehicle is unlocked by theremote entry key fob. Vehicles equipped with auto lamps, the puddle,head, park, and tail lamps illuminate. Vehicles not equipped with autolamp, only the puddle, park and tail lamps illuminate. The syst...

Your vehicle has a factory-set 5–digit code that operates the keylessentry system. You can also program your own 5–digit personal entrycode. The factory-set code is located: • on the owner’s wallet card in the glove compartment • on the inner side of the passenger compartment fuse box • or at your d...

If you wish to erase your personal code, use the following instructions: Erasing personal code 1. Enter the factory-set code. 2. Press 1/2 within five seconds ofstep 1 and release. 3. Press the 1/2 control and hold for2 seconds to erase the customerprogrammed keycode, within fiveseconds of step 2. T...

Autolock (if equipped) The autolock feature will lock all of the vehicle doors when: • all doors are closed • the engine is running and • you shift into any gear putting the vehicle in motion The autolock feature repeats when: • any door, except the drivers door, is opened then closed while theengin...

Automatic arming The vehicle is armed immediatelyafter switching the ignition to the 3(OFF) position. The THEFT light in the instrument cluster will flashevery two seconds when the vehicleis armed. Automatic disarming Switching the ignition to the 4 (ON) position with a coded key disarms the vehicle...

Programming spare keys A maximum of eight keys can be coded to your vehicle. OnlySecuriLock y keys can be used. To program a coded key yourself, you will need two previously programmed coded keys (keys that already operate your vehicle’s engine) and the new unprogrammed key(s) readilyaccessible for ...

PERIMETER ALARM SYSTEM (IF EQUIPPED) The perimeter anti-theft system will help prevent your vehicle fromunauthorized entry. If there is any potential perimeter anti-theft problem with your vehicle,ensure ALL key fobs (remote entry transmitters) are brought to the dealership, to aid in troubleshootin...

When you press the lock controltwice within three seconds on yourremote entry transmitter, the hornwill chirp once to let you know thatall doors/hood and liftgate (wagon)are closed. If the doors/hood or liftgate (wagon) are not closed and you press theremote entry transmitter twice to confirm the do...

• Press the PANIC control on theremote entry transmitter. Thiswill only shut the horn OFF whenthe alarm is sounding. The alarmsystem will still be armed. Triggering the anti-theft system The armed system will be triggered if: • Any door, liftgate or hood is opened without using the door key or there...

SEATING Adjustable head restraints Your vehicle’s seats are equipped with head restraints which arevertically adjustable. The purpose of these head restraints is to help limithead motion in the event of a rear collision. To properly adjust your headrestraints, lift the head restraint so that it is l...

Adjusting the front manual seat Never adjust the driver’s seat or seatback when the vehicle ismoving. Do not pile cargo higher than the seatbacks to reduce the risk ofinjuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lapbelt snug and low across t...

Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle ismoving. Do not pile cargo higher than the seatbacks to avoid injuringpeople in a collision or sudden stop. Always drive and ride with your seatback upright and the lapbelt snug and low across t...

REAR SEATS 2nd seat/split-folding rear seat (if equipped) One or both rear seatbacks can be folded down to provide additionalcargo space. To lower the seatback(s) frominside the vehicle, pull tab to releaseseat back and then fold seatbackdown. When raising the seatback(s), make sure you hear the sea...

How does the personal safety system work? The Personal Safety System can adapt the deployment strategy of yourvehicle’s safety devices according to crash severity and occupantconditions. A collection of crash and occupant sensors providesinformation to the Restraints Control Module (RCM). During a c...

allows your Personal Safety System to tailor the air bag deployment andsafety belt pretensioner activation depending upon safety belt usage.Refer to Safety Belt section in this chapter. Front safety belt pretensioners The safety belt pretensioners are designed to tighten the safety beltsfirmly again...

Safety belt precautions Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. To reduce the risk of injury, make sure children sit where theycan be properly restrained. Never let a passenger hold a child on his or her lap while thevehicle is moving. The passe...

Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing freeshoulder belt length adjustment to your movements and locking inresponse to vehicle movement. For example, if the driver brakessuddenly or turns a corner sharply, or the vehicle receives an impact ofapproxim...

• Grasp the shoulder portion andpull downward until the entirebelt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automatic lockingmode. How to disengage the automatic locking mode Ford Motor Company recomm...

Failure to replace the Belt and Retractor assembly couldincrease the risk of injury in collisions. Safety belt pretensioner Your vehicle is equipped with safety belt pretensioners at the driver andfront outboard passenger seating positions. The safety belt pretensioners are designed to activate only...

Front safety belt height adjustment Your vehicle has safety belt heightadjustments for the driver and frontpassenger. Adjust the height of theshoulder belt so the belt restsacross the middle of your shoulder. To lower the shoulder belt height,pull the control down and slide theheight adjuster down. ...

Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a right angle to the beltand pull across your lap until itreaches the buckle. To tighten thebelt, pull the loose end of the beltthrough the tongue until it ...

grasp the tongue so that it is parallel to the webbing and slide thetongue upward. Provide enough length so that the tongue can reach thebuckle. To fasten the belt, pull the combination lap and shoulder belt from theretractor so that the shoulder belt portion of the safety belt crosses yourshoulder ...

If... Then... The driver’s safety belt isbuckled before the ignitionswitch is turned to the ONposition... The BeltMinder feature will notactivate. The purpose of the BeltMinder is to remind occasional wearers to wearsafety belts all of the time. The following are reasons most often given for not wea...

Reasons given... Consider... “Belts wrinkle my clothes” Possibly, but a serious crash can domuch more than wrinkle your clothes,particularly if you are unbelted. “The people I’m with don’twear belts” Set the example, teen deaths occur 4times more often in vehicles withTWO or MORE people. Children an...

Safety belt extension assembly If the safety belt is too short when fully extended, there is a 20 cm(8 inch) safety belt extension assembly that can be added (part number611C22). This assembly can be obtained from your dealer at no cost. Use only extensions manufactured by the same supplier as the s...

AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM Your vehicle is equipped with a crash sensing and diagnostic modulewhich records information about the air bag and sensor systems. In theevent of a collision this module may save information related to thecollision including information about the air bag system ...

The air bag supplemental restraints are an intergral part of the PersonalSafety System. They are designed to be deployed in cases where thePersonal Safety System has determined the occupant conditions andcrash severity are appropriate to activate these devices. Refer to the Personal Safety System se...

Steps you can take to properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching thepedals comfortably. • Recline the seat slightly (one or two degrees) from the uprightposition. Do not put anything on or over the air bag module. Placingobjec...

Children and air bags For additional important safetyinformation, read all information onsafety restraints in this guide. Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating posit...

How do the air bag supplemental restraints work? The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (...

How does the side air bag system work? The side air bag system consists ofthe following: • An inflatable nylon bag (air bag)with a gas generator concealedbehind the outboard bolster ofthe driver and front passengerseatbacks. • A special seat cover designed toallow airbag deployment. • The same warni...

Several air bag systemcomponents get hot after inflation. Do not touch them afterinflation. If the side air bag hasdeployed, the air bag will not function again. The sideair bag system (including theseat) must be inspected andserviced by a qualifiedtechnician in accordance withthe vehicle service ma...

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant orchild restraint you might use. When possible, always place children under age 12...

SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all of the manufacturer’s instructions with thesafety seat you put in your vehicle. If you do not install and use thesafety seat properly, the ...

• Put the safety belt in the automatic locking mode. Refer to Automatic locking mode. Ford recommends the use of a child safety seat having a top tetherstrap. Install the child safety seat in a seating position which is capableof providing a tether anchorage. For more information on top tetherstraps...

Installing child safety seats in the lap belt seating positions 1. Lengthen the lap belt. To lengthen the belt, hold the tongue so that itsbottom is perpendicular to the direction of webbing while sliding thetongue up the webbing. 2. Place the child safety seat in the center seating position. 3. Rou...

STARTING Positions of the ignition 1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 2. LOCK, locks the steering wheel,automatic transmission gearshiftlever and allows key removal. 3. OFF, shuts off the engine withoutlocking the steering wheel...

Do not start your vehicle in a closed garage or in other enclosedareas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions. If you smell exhaust fumes inside your vehicle, have your dealerinspe...

3. If the temperature is below -12° C (10° F) and the engine does notstart in 15 seconds on the first try, turn the key OFF and wait 10seconds and try again. If the engine does not start in two attempts, Pressthe accelerator pedal all the way to floor and hold. Turn the key toSTART position. 4. When...

3. When the engine starts, release the key, then release the acceleratorpedal gradually as the engine speeds up. 4. If the engine still fails to start, repeat steps one through three. 5. After the engine starts, hold your foot on the brake pedal, put thegearshift lever in gear and release the parkin...

WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or otherreproductive harm. In addition, certain fluids contained in vehicles andcertain products of component wear contain or...

heard during this test. This is normal. If a malfunction is found, the ABSwarning light will come on. If the vehicle has continuous vibration orshudder in the steering wheel while braking, the vehicle should beinspected by a qualified service technician. The ABS operates by detecting theonset of whe...

Parking brake Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops. The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released....

Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy. Park brake warning chime Sounds when the parking brake is set, the engine is running and thetransaxle is not in P (Park) or N (Neutral). The chime will shut o...

During Traction Control y operation, the traction control active light willilluminate, you may hear an electricmotor type of sound coming fromthe engine compartment and theengine will not “rev-up” when you push further on the accelerator. Thisis normal system behavior. The Traction Control y on/off ...

• high crown in center of road • high crosswinds • wheels out of alignment • loose or worn suspension components AUTOMATIC TRANSAXLE OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever from being moved from P (Park) when the ...

Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn off the ignition whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lampremains illuminated, the brakes may not be working properly. See your dealer or a qualified s...

Hold the brake pedal down while you move the gearshift leverfrom P (Park) to another position. If you do not hold the brake pedal down, your vehicle may move unexpectedly and injure someone. Understanding gearshift positions P (Park) Always come to a complete stopbefore shifting into P (Park). Makes...

When parking, do not use the gearshift in place of the parkingbrake. Always set the parking brake fully and make sure that the gearshift is securely latched in Park (P). Turn off the ignitionwhenever you leave your vehicle. Never leave your vehicle unattendedwhile it is running. If you do not take t...

Always ensure that the weight of occupants, cargo and equipment beingcarried is within the weight limitations that have been established foryour vehicle including both gross vehicle weight and front and rear grossaxle weight rating limits. Under no circumstance should these limitationsbe exceeded. E...

3.0L 4-Valve Duratec Engine Model PassengerLoad - #/kg(lbs.) Luggage Load -kg (lbs.) Max TrailerWt.- kg (lbs.) Sedan 5/340 (750) 0 590 (1 300) 2/135 (300) 70 (150) 725 (1 600) 2/135 (300) 0 795 (1 750) Wagon 5/340 (750) 70 (150) 455 (1 000) 2/135 (300) 70 (150) 660 (1 450) 2/135 (300) 0 725 (1 600) ...

If you use a rental trailer, follow the instructions that the rental agencygives to you. Do not attach safety chains to the bumper. Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes aresafe if installed properly and adjusted to the manufacturer’sspecifications. The tr...

Trailer towing tips • Practice turning, stopping and backing up before starting on a trip toget the feel of the vehicle trailer combination. When turning, makewider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached. • If you ...

GETTING ROADSIDE ASSISTANCE To fully assist if you should have a vehicle concern, Ford Motor Companyoffers a complimentary roadside assistance program. This program isseparate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for the Basic warranty peri...

FUSES AND RELAYS Fuses If electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check the appropriatefuses before replacing any electricalcomponents. Note: Always replace a fuse with one that has the specified amperage r...

Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel bythe brake pedal. Remove the panel cover to access the fuses. To remove a fuse use the fuse puller tool provided on the fuse panelcover. The fuses are coded as follows. Fuse/relay location Fuse am...

Power distribution box The power distribution box islocated in the engine compartment.The power distribution box containshigh-current fuses that protect yourvehicle’s main electrical systemsfrom overloads. Always disconnect the battery before servicing high currentfuses. To reduce risk of electrical...

• drive through an automatic car wash, because of the vehicle’s reducedground clearance • try to repair the temporary spare tire or remove it from its wheel • use the wheel for any other type of vehicle Tire change procedure 1. Park on a level surface, activate hazard flashers and set parking brake....

6. Put the jack in the jack notchnext to the door of the tire you arechanging. Turn the jack handleclockwise until the wheel iscompletely off the ground. 7. Remove the lug nuts with the lugnut wrench. 8. Replace the flat tire with the spare tire, making sure the valve stem isfacing outward. Reinstal...

JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes, andclothing, if contacted. Do not attempt to push-start your vehicle. ...

Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+)term...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable. Make theconnection to an exposed metal part of the stalled vehicle’s engine, awayfrom the battery and the carburetor/fuel injection system. Do not use fuel ...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingbelt. Ford Motor Company has notapproved a ...

If your vehicle must be towed with the drive wheels on the ground: • Place the transaxle in N (Neutral). • DO NOT exceed the distance of 80 km (50 miles). • DO NOT exceed the speed of 56 km/h (35 mph). If the vehicle is towed by other means or incorrectly, vehicledamage may occur. Ford Motor Company...

GETTING THE SERVICES YOU NEED At home Ford Motor Company and Ford of Canada have authorized dealerships toservice your vehicle. It is preferred that you return to the Ford dealerwhere your vehicle was purchased when warranty repairs are needed.However, you may also take your vehicle to another Ford ...

In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action un...

THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes • available free to owners and lessees of qualifying Ford Motor Companyvehicles The Dispute Settlement Board may not be available in all states. FordMotor...

Board membership The Board consists of: • three consumer representatives • a Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained byan independent consulting firm. The dealership Board member is chosenfrom Ford and Lincoln Mercury deale...

You will receive a letter of explanation if your application does notqualify for Board review. Oral presentations If you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral presentationbefore the Board, this is not a requireme...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) In those cases where you continue to feel that the efforts by Ford andthe dealer to resolve a factory-related vehicle service concern have beenunsatisfactory, Ford of Canada participates in an impartial third partymediation/arbitration program...

If your vehicle must be serviced while you are traveling or living inCentral or South America, the Caribbean, or the Middle East, contact thenearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANYWORLDWIDE DIRECT MARKET OPERATIONS1555 Fairlane DriveFairlane Busi...

WASHING THE EXTERIOR OF YOUR VEHICLE Never wash a vehicle that is “hot tothe touch” or during exposure tostrong, direct sunlight. It isrecommended that you wash yourvehicle regularly with cool orlukewarm water and a neutral Phshampoo, such as Detail Wash(ZC-3–A), which is available fromyour authoriz...

CLEANING THE ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • The engine must be cool to the touch before spraying with water. • Never spray a hot engine with cold water, as damage to theengine block or engine co...

• 3.0L Duratec engine • Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage. WASHING NON-PAINTED PLASTIC EXTERIOR PARTS Use Detail Wash (ZC-3–A) for routine cleaning. If tar or grease spots are present, clean with Extra Strength Tar andRoad Oil Re...

Do not use household cleaning products, alcohol solutions,solvents or cleaners intended for rubber, vinyl and plastics, oroil/petroleum-based leather conditioners. These products maycause premature wearing of the clear, protective coating. CLEANING THE INSIDE WINDOWS Use Ultra Clear Spray Glass Clea...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a scheduled maintenance guide which makes trackingroutine service easy. If your vehicle requires professional service, your dealership can providethe...

Working with the engine on 1. Set the parking brake and ensure the gearshift is securely latched in P(Park). 2. Block the wheels to prevent the vehicle from moving unexpectedly. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE ...

3.0L DOHC V6 Duratec engine 1. Automatic transmission fluid dipstick 2. Brake fluid reservoir 3. Air filter assembly 4. Battery 5. Engine oil dipstick 6. Engine oil filler cap 7. Engine coolant reservoir 8. Windshield washer fluid reservoir 9. Power steering fluid reservoir Maintenance and Specifica...

WINDSHIELD WASHER FLUID Washer fluid Check the washer fluid wheneveryou stop for fuel. The reservoir ishighlighted with a symbol. If the level is low, add enough fluidto fill the reservoir. In very coldweather, do not fill the reservoir allthe way. Only use a washer fluid that meets Ford specificati...

Checking and adding washer fluid for the liftgate (if equipped) The opening for the reservoir islocated on the passenger side underthe tail lamp. Refill this reservoirwith the same fluid you use for yourwindshield. ENGINE OIL Checking the engine oil Refer to the scheduled maintenance guide for the a...

5. Locate and carefully remove theengine oil indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove it again. • If the oil level is between the add 1QT and FULL marks or between the MIN and MAX marks (depending on application), the oil level is acceptable. DO NOT ...

Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler capand use a funnel to pour the engine oil...

Ford production and aftermarket (Motorcraft) oil filters are designed foradded engine protection and long life. If a replacement oil filter is usedthat does not meet Ford material and design specifications, start-upengine noises or knock may be experienced. It is recommended you use the appropriate ...

Batteries normally produce explosive gases which can causepersonal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery,always shield your face and protect your eyes. Always provide properventilation. When lifting a plastic-case...

• The vehicle may need to be driven 16 km (10 miles) or more torelearn the idle and fuel trim strategy. • If you do not allow the engine to relearn its idle trim, the idlequality of your vehicle may be adversely affected until the idletrim is eventually relearned. If the battery has been disconnecte...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “cold fill level” or within the “coldfill range” as listed on the engine coolant reservoir (depending uponapplication). • Refer to the Scheduled Maintenance Guide for service interval...

Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine...

If you have to add more than 1.0 liter (1.0 quart) of engine coolant permonth, have your dealer check the engine cooling system. Your coolingsystem may have a leak. Operating an engine with a low level of coolantcan result in engine overheating and possible engine damage. Recycled engine coolant For...

If you drive in extremely hot climates: • It is still necessary to maintain the coolant concentrationabove 40%. • NEVER decrease the coolant concentration below 40%. • Decreased engine coolant concentrations below 40% willdecrease the corrosion protection characteristics of the enginecoolant and may...

Fuel ethanol and gasoline may contain benzene, which is acancer-causing agent. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materialsand any open flames beforefueling your vehicle. • Always turn off the vehicle beforefueling. • Automotive fuels can be harm...

When refueling always shut the engine off and never allowsparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions.Care should be taken to avoid inhaling excess fumes. The flow of fuel through a fuel pump nozzle can produce st...

FFV engine (if equipped) Your FFV will operate well on ordinary “Regular” unleaded gasoline, butonly the highest quality fuel ethanol will provide the same level ofprotection and performance. To identify if your vehicle is an FFV, checkyour VIN or the label on the inside of your fuel filler door. Wh...

• Use the same side of the same pump and have the vehicle facing thesame direction each time you fill up. • Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completel...

• Slow down gradually. • Driving at reasonable speeds (traveling at 88 km/h [55 mph] uses 15%less fuel than traveling at 105 km/h [65 mph]). • Revving the engine before turning it off may reduce fuel economy. • Using the air conditioner or defroster may reduce fuel economy. • You may want to turn of...

• Driving on flat terrain offers improved fuel economy as compared todriving on hilly terrain. • Transmissions give their best fuel economy when operated in the topcruise gear and with steady pressure on the gas pedal. • Close windows for high speed driving. EPA window sticker Every new vehicle shou...

CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid.Refer to the scheduled maintenanceguide for the service intervalschedules. If adding fluid isnecessary, use only MERCON t ATF. 1. Start the engine and let it run until it reaches normal operatingtemperature (the engine coolant t...

BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked andrefilled as needed. Refer to thescheduled maintenance guide forthe service interval schedules. 1. Clean the reservoir cap beforeremoval to prevent dirt or waterfrom entering the reservoir. 2. Visually inspect the fluid leve...

TRANSMISSION FLUID Checking automatic transmission fluid Refer to your scheduled maintenance guide for scheduled intervals forfluid checks and changes. Your transaxle does not consume fluid.However, the fluid level should be checked if the transaxle is not workingproperly, i.e., if the transaxle sli...

Correct fluid level The transmission fluid should be checked at normal operatingtemperatures 66°C-77°C (150°F-170°F) on a level surface. The normaloperating temperature can be reached after approximately 30 km(20 miles) of driving. The transmission fluid should be inthis range if at normal operating...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B, and C, representing thetire’s resistance to the gen...

Tire rotation Because your vehicle’s tires perform different jobs, they often weardifferently. To make sure your tires wear evenly and last longer, rotatethem as indicated in the scheduled maintenance guide. If you notice thatthe tires wear unevenly, have them checked. • Four tire rotation Replacing...

Make sure that all replacement tires are of the same size, type,load-carrying capacity and tread design (e.g., “All Terrain”, etc.), as originally offered by Ford. Failure to follow these precautions may adversely affect thehandling of the vehicle and make it easier for the driver to lose control an...

MOTORCRAFT PART NUMBERS Component 3.0L V6 Vulcanengine 3.0L FFV V6engine 3.0L DOHC V6Duratec engine Air filterelement 1 FA-1683 FA-1683 FA-1683 Fuel filter FG-1006 FG-1006 FG-1006 Battery(standard) BXT-36R BXT-36R BXT-36R Battery(optional) BXT-36R N/A N/A Oil filter FL-400-S FL-400-S FL-820-S PCV va...

Vehicle identification number The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Please note thatin the graphic XXXX isrepresentative of your vehicleidentification number.) 1. World manufacturer identifier 2. Brake type and gross vehiclewei...

FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of genuine Ford accessories are available for yourvehicle through your local authorized Ford, Lincoln Mercury or Ford ofCanada dealer. These quality accessories have been specificallyengineered to fulfill your automotive needs; they are custom desig...

A Accessory delay ..........................70 Air bag supplementalrestraint system ........121–122, 126 and child safety seats ............124description ......................122, 126disposal ....................................128driver air bag ..........121, 125, 127indicator light ................

Locks autolock .....................................94childproof ..................................85doors ..........................................85 Lubricantspecifications .....................234, 236 Lumbar support, seats .............101 M Mirrors .........................................68 a...