Ford 2002 Ranger v.2- Manuals

Fuel pump shut-off switch In the event of an accident the safety switch will automatically cut off the fuel supply to the engine. The switch can also be activated through sudden vibration(e.g. collision when parking). To reset the switch, refer to the Fuel pump shut-off switch in the Roadside emerge...

SPECIAL NOTICES Emission warranty The New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and 7.3LPower Stroke Diesel Engine Coverage. In addition, your vehicle is eligiblefor Emissions Defect and Emissions Performance Warranties. For adetai...

Using your vehicle with a snowplow Do not use this vehicle for snowplowing. Using your vehicle as an ambulance Do not use this vehicle as an ambulance. Your vehicle is not equipped with the Ford Ambulance PreparationPackage. Electric vehicles For information on operating your Electric Vehicle, also ...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat InstallationWarning Child Seat TetherAnchorage Brake System Anti-Lock Brake System Brake Fluid -Non-Petroleum Based Tr...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

Light is blinking: Engine misfire is occurring which could damage your catalytic converter. Youshould drive in a moderate fashion (avoid heavy acceleration anddeceleration) and have your vehicle serviced at the first available opportunity. Under engine misfire conditions, excessive exhaust temperatu...

will momentarily illuminate just prior to reaching the START position). If thelight remains on, continues to flash or fails to illuminate, have the ABSserviced immediately. If the ABS light remains on, it means the anti-lockbrake system has malfunctioned and is disabled, however, the normal brakesys...

Speed control Illuminates when the speed controlis activated. O/D off (if equipped) Illuminates when the overdrivefunction has been turned OFF usingthe Transmission Control Switch(TCS) on end of gearshift. If thelight does not come on or the light flashes steadily, have your vehicleserviced as soon ...

Four wheel drive high (if equipped) Illuminates when four-wheel drive isput in high range. If the lightcontinues to flash have the systemserviced. Four wheel drive high (if equipped) Illuminates when four-wheel drive isput in high range. If the lightcontinues to flash have the systemserviced. Four w...

Engine oil pressure gauge Indicates engine oil pressure. Atnormal operating temperature, theneedle will be in the normal range(the area between the “L” and “H”);if the needle goes below the normalrange, stop the vehicle as soon assafely possible and switch off theengine immediately. Check the oillev...

Speedometer Indicates the current vehicle speed. Odometer Registers the total kilometers(miles) of the vehicle. Trip odometer Registers the kilometers (miles) ofindividual journeys. To reset,depress the control. Tachometer Indicates the engine speed inrevolutions per minute. Driving with your tachom...

AM/FM STEREO Volume/power control Press the control to turn the audiosystem on or off. Turn the control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition switch is turned bac...

AM/FM select The AM/FM select control works inradio mode. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press thecontrol to switch between AM, FM1 or FM2 memory preset stations. Tune adjust The tune control works in radio mode. Tune adjust in radio mode • Pre...

Radio station memory preset The radio is equipped with four station memory preset controls. Thesecontrols can be used to select up to four preset AM stations and eightFM stations (four in FM1 and four in FM2). Setting memory preset stations 1. Select the frequency band with the AM/FM select control....

Speaker balance adjust Speaker sound distribution can beadjusted between the right and leftspeakers. Press the TONE control three times,then use the volume knob to adjustthe desired level. Setting the clock Press CLK to toggle betweenlistening frequencies and clockmode. To set the hour, press and ho...

If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition switch is turned back on. AM/FM select The AM/FM select control works inradio and CD modes. AM/FM select in radio mode This control allows you to sel...

• Press to select the next disc in the CD changer. Hold the control to fast-forward through the remaining discs. Seek function The seek function control works in radio or CD mode. Seek function in radio mode • Press to find the next listenable station down thefrequency band. • Press to find the next...

Radio station memory preset The radio is equipped with four or six station memory preset controls.These controls can be used to select up to four or six preset AM stationsand eight or twelve FM stations (four to six in FM1 and four to six inFM2). Setting memory preset stations 1. Select the frequenc...

Speaker balance adjust Speaker sound distribution can beadjusted between the right and leftspeakers. Speaker fade adjust Speaker sound can be adjustedbetween the front and rearspeakers. CD select • To begin CD play (if CD[s] areloaded), press the CD control.The first track of the disc willbegin play...

Fast forward The fast forward control works in CD mode. To fast forward in CD mode, pressthe CD control (preset 2). Pressing the control for less thanthree seconds results in slowforward action. Pressing the control for more than three seconds resultsin fast forward action. Eject function Press the ...

MACH T MP3 MUSIC SYSTEM 1. ON/OFF and volume control 2. AM/FM control 3. Bass control 4. Treble control 5. Fade control 6. Balance control 7. Seek control 8. Scan control 9. Clock control 10. Tune/Directory control 11. CD control 12. MP3 directory control 13. Eject control 14. CD rewind control 15. ...

MP3 functions Your audio system is equipped with MP3 capability which allows you tolisten to songs in MP3 flat file mode and MP3 directory mode. To engage MP3 flat file mode, insert an MP3 disc. If an MP3 disc isalready present in the player, press the CD control. The MP3 icon willdisplay while the ...

Radio station memory preset The radio is equipped with six station memory preset controls. Thesecontrols can be used to select up to six preset AM stations and twelveFM stations (six in FM1 and six in FM2). Setting memory preset stations 1. Select the frequency band withthe AM/FM select control. 2. ...

Bass adjust The bass adjust control allows youto increase or decrease the audiosystem’s bass output. Treble adjust The treble adjust control allows youto increase or decrease the audiosystem’s treble output. Speaker balance adjust Speaker sound distribution can beadjusted between the right and lefts...

Playing a CD • If a CD is already loaded, pressthe CD control. CD play willbegin where it stopped last. • If a CD is not already loaded,insert the CD into the system. CD will briefly appear in the displayand then the first track on the disc will begin playing. Playing an MP3 disc in MP3 flat file mo...

• Press on TUNE DIR to revert to the previous directory on the MP3 disc. If the current directory is the first directory on the disc,pressing will select the last directory on the disc. Press and hold for fast selection. Eject function Press the control to stop and eject adisc. If a disc is ejected ...

Compression adjust brings soft andloud CD passages together for amore consistent listening level.Press the COMP control to activate compression adjust. The compression icon(c) will illuminate in the display while the compression function is enabled.Press the COMP control again to disengage the featu...

• To select another random trackon the disc, press or on the SEEK control. • Press SCN to scan throughrandom tracks. The track numberwill flash in the display. Theshuffle function will remainenabled. • Press SHUFFLE again todisengage the shuffle feature.SHF and then OFF will brieflydisplay and the c...

To shuffle tracks in anotherdirectory, press or on the TUNE DIR control to select thedesired directory. The shuffle function still remains enabled.Press the SHUFFLE control again to disengage the SHUFFLE feature. SHUFand OFF will briefly display and the current track will continue to play. MACH T Tr...

• The player supports multi session discs. However, be sure to importthe previous session of the disc before you add new files. If you do notimport the previous session, only the last session will be played. • When burning a disc, ensure that you close/finalize the disc before playback,or the disc m...

Setting memory preset stations 1. Select the frequency band withthe AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns,indicating the station is held in memory...

Bass adjust The bass adjust control allows youto increase or decrease the audiosystem’s bass output. Press the BASS control then press: • to decrease the bass output and • to increase the bass output. Treble adjust The treble adjust control allows youto increase or decrease the audiosystem’s treble ...

Speaker fade adjust Speaker sound can be adjustedbetween the front and rearspeakers. Press the FADE control then press: • to shift the sound to the front and • to shift the sound to the rear. Tape/CD select • To begin tape play (with a tapeloaded into the audio system)while in the radio or CD mode,p...

Fast forward The fast forward control works intape and CD modes. • In the tape mode, tape directionwill automatically reverse whenthe end of the tape is reached. • In CD mode, pressing the control fast forwards the CD within thecurrent track. Tape direction select Press SIDE 1–2 to play the alternat...

Compression adjust Compression adjust brings soft andloud CD passages together for amore consistent listening level. Press the COMP control to activateand deactivate compression adjust. Shuffle feature The shuffle feature operates in CDmode and plays all tracks in randomorder. Press the SHUFFLE cont...

• to decrease minutes and • to increase minutes. If your vehicle has a separate clock,(other than the digital radiodisplay), the CLK control will notfunction in the above manner. The CLK control will allow you toswitch between media display mode(radio station, stereo information,etc.) and clock disp...

PREMIUM AM/FM STEREO IN DASH SIX CD RADIO Volume/power control Press the control to turn the audiosystem on or off. Turn the control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when the...

Radio station memory preset The radio is equipped with six station memory preset controls. Thesecontrols can be used to select up to six preset AM stations and twelveFM stations (six in FM1 and six in FM2). Setting memory preset stations 1. Select the frequency band with the AM/FM select control. Pr...

CD select CD mode may be entered bypressing the CD control and theLOAD control. Load the CD into theaudio system. The first track of thedisc will begin playing. After that,CD play will begin where it stopped last. If an alternative CD is desired, press the corresponding preset control (1–6)of a load...

Auto load This feature allows you to autoloadup to 6 discs into the multi disc CDplayer internal to the radio. Press and hold the LOAD control until AUTOLOAD # is displayed. TheCD door will open. Load the desired disc, one at a time. The CD isloaded into position and the audio system will display CD...

Traffic announcements This feature allows you to heartraffic announcements. When in thismode, traffic announcements willinterrupt radio and CD play. When in FM mode and RDS isactivated, press the MENU until TRAFFIC OFF displays. Press the SELcontrol to engage the feature. The display will read TRAFF...

To activate RDS: • When in FM mode, press the MENU control until RDS OFF displays. • Press the SEL control to engage this feature (RDS ON). RDS features: Once the RDS feature is on, press the MENU control to scroll throughthe following selections: Traffic announcements This feature allows you to hea...

• Jazz • Oldies • R & B • Religious • Rock • Soft • Top 40 Show This feature allows you to select thetype of RDS broadcast informationthe radio will regularly show in thedisplay. With RDS activated, press theMENU control until SHOW isdisplayed. Use the SEL control to select TYPE(displays the RDS...

CD, MP3 AND CD PLAYER CARE • Handle discs by their edges only. Never touch the playing surface. • Do not expose discs to direct sunlight or heat sources for extendedperiods of time. • Do not insert more than one disc into the slot of the CD player (if equipped). • Always store discs out of direct su...

HEATER ONLY SYSTEM (IF EQUIPPED) Fan speed control Controls the volume of air circulatedin the vehicle. Temperature control knob Controls the temperature of theairflow inside the vehicle. Onheater-only systems, the air cannotbe cooled below the outsidetemperature. Mode selector control Controls the ...

Operating tips • In humid weather, place the climate control system in DEF beforedriving. This will reduce fogging on your windshield. Once thewindshield has been cleared, select any desired position. • To reduce humidity buildup inside the vehicle, do not drive with theclimate control system in the...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) Fan speed control Controls the volume of air circulatedin the vehicle. Temperature control knob Controls the temperature of theairflow inside the vehicle. Mode Selector Control Controls the direction of the airflowto the inside of the vehicle. ...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parkinglamps. Rotate to the second positionto turn on the headlamps. Foglamp control (if equipped) The foglamps can be turned onwhen the headlamp control is ineither of the following positions: • Parking lamps • Low bea...

High beams • Push forward past detent toactivate. • Pull toward you past detent todeactivate. Flash to pass Pull toward you slightly to activateand release to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of theinstrument panel during headlampand parklamp operation. • Rotate up to br...

• Map lamp For bulb replacement, see a dealer or qualified technician. Replacing headlamp bulbs To remove the headlamp bulb: 1. Make sure headlamp switch is inOFF position, then open the hood. 2. Remove two screws and cover (ifequipped). 3. At the back of the headlamp, pryup the two retainer pins to...

Handle a halogen headlamp bulb carefully and keep out ofchildren’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb tobreak the next time the headlamps are operated. 1. With the flat side of the bulb’s plastic base facing upward, ...

Replacing tail lamp/backup lamp bulbs The tail lamp/backup lamp bulbs arelocated in the same portion of thetail lamp assembly, one just belowthe other. Follow the same steps toreplace either bulb: 1. Open the tailgate to expose thelamp assemblies. 2. Remove the four screws and thelamp assembly from ...

Replacing foglamp bulbs 1. Remove the bulb socket from thefoglamp by turningcounterclockwise. 2. Disconnect the electricalconnector from the foglamp bulb. 3. Connect the electrical connector to the new foglamp bulb. 4. Install the bulb socket in the foglamp turning clockwise. Replacing high-mount br...

Replacing license plate lamp bulbs The license plate bulbs are locatedbehind the rear bumper. To changethe license plate lamp bulbs: 1. Reach behind the rear bumper tolocate the bulb socket. 2. Twist the socket counterclockwiseand remove. 3. Pull out the old bulb from socketand push in the new bulb....

WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper controlto the desired interval, low or highspeed position. The bars of varying length are forintermittent wipers. When in thisposition rotate the control upwardfor fast intervals and downward forslow intervals. Push (tap) the end of the st...

Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from thewindshield and lock into the serviceposition. 2. Turn the blade at an angle fromthe wiper arm. Push the lock pinmanually to release the blade andpull the wiper blade down towardthe windshield to remove it from ...

Never adjust the steering wheel when the vehicle is moving. AUXILIARY POWER POINT Power outlets are designed for accessory plugs only. Do not hangany type of accessory or accessory bracket from the plug.Improper use of the power outlet can cause damage not coveredby your warranty. The auxiliary powe...

POWER WINDOWS (IF EQUIPPED) Press and hold the rocker switches to open and close windows. • Press the top portion of therocker switch to close. • Press the bottom portion of therocker switch to open. One touch down • Press AUTO completely down andrelease quickly. The driver’swindow will open fully. ...

POWER SIDE VIEW MIRRORS (IF EQUIPPED) To adjust your mirrors: 1. Select to adjust the left mirror or to adjust the right mirror. 2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the center position tolock mirrors in place. SPEED CONTROL (IF EQUIPPED) To turn speed contro...

To turn speed control off • Press OFF or • Turn off the vehicle ignition. Once speed control is switched off,the previously programmed setspeed will be erased. To set a speed • Press SET ACC. For speedcontrol to operate, the speedcontrol must be ON and thevehicle speed must be greaterthan 48 km/h (3...

To disengage speed control • Depress the brake pedal or • Depress the clutch pedal (ifequipped). Disengaging the speed control willnot erase the previouslyprogrammed set speed. Fullydepressing the clutch pedal maycause a flare in engine RPM as thethrottle is returned to idle. This isnormal. Pressing...

To return to a previously set speed • Press RSM. For RSM to operate,the vehicle speed must be fasterthan 48 km/h (30 mph). Indicator light This light comes on when either theSET ACCEL or RES controls arepressed. It turns off when the speedcontrol OFF control is pressed, thebrake or clutch is applied...

To return to normal overdrive mode,press the Transmission ControlSwitch again. The TCIL will nolonger be illuminated. When you shut off and re-start yourvehicle, the transmission will automatically return to normal(Overdrive) mode. For additional information about the gearshift lever and the transmi...

BED EXTENDER (IF EQUIPPED) Your vehicle may be equipped with a bed extender designed to extendthe pickup box for longer loads. To extend the bed extender: 1. Lower tailgate. 2. Pull the round knobs on each sideof the extender to release it fromthe pickup box. 3. Pivot extender on to the tailgate. Dr...

To remove the bed extender: 1. Extend the bed extender. 2. Pull the round knobs on each sideof the extender to unlock it. Make sure the locking clip screwsare loose before removing theextender. 1. Press the locking clips below themiddle bar on each side and lift theextender out of the bed. To instal...

To stow the rear panel: • Before driving with the tonneaucover open, stow the rear panel. • Release four cylinder clips andremove two hydraulic cylindersfrom the pickup box and rearpanel. • Lift the rear panel up, lay it ontop of the front panel and secureit with the two straps on thefront panel tie...

KEYS The key operates all locks on yourvehicle. In case of loss, replacementkeys are available from your dealer. You should always carry a secondkey with you in a safe place in caseyou require it in an emergency. Refer to SecuriLock y Passive Anti-Theft System for more information. POWER DOOR LOCKS ...

The remote entry features only operate with the ignition in the LOCKposition. If there is any potential remote keyless entry problem with your vehicle,ensure ALL remote entry transmitters are brought to the dealership, to aid in troubleshooting. Unlocking the doors Press this control to unlock thedr...

Deactivating/activating power door lock disable feature 1. Turn the ignition key to ON, thenpress the UNLOCK button 3 times. 2. Turn the ignition key to OFF,then press the UNLOCK button 3times. 3. Turn the ignition key to ON,within five seconds press theUNLOCK button 2 times then LOCKonce. The user ...

• nearby radio towers • structures around the vehicle • other vehicles parked next to the vehicle To replace the battery: 1. Twist a thin coin between the twohalves of the transmitter near thekey ring. DO NOT TAKE THEFRONT PART OF THETRANSMITTER APART. 2. Place the positive (+) side of newbattery in...

To program the transmitters yourself: • Place the key in the ignition andturn from 2 (LOCK) to 3 (OFF)and cycle between 3 (OFF) and4(ON) eight times in rapidsuccession (within 10 seconds)with the eighth turn ending in the4 (ON) position. The doors willlock/unlock to confirm thatprogramming mode has ...

SECURILOCK Y PASSIVE ANTI-THEFT SYSTEM (IF EQUIPPED) SecuriLock y passive anti-theft system is an engine immobilization system. This system prevents the engine from being started unless a coded key programmed to your vehicle is used. The SecuriLock y passive anti-theft system is not compatible with ...

Certain items may cause vehiclestarting issues: • large metallic objects • electronic devices on the keychain that can be used topurchase gasoline or similar items • a second key on the same keyring as the coded key If any of these items are present,you need to keep these objects fromtouching the co...

SEATING Adjusting the front manual seat Never adjust the driver’s seat or seatback when the vehicle ismoving. Do not pile cargo higher than the seatbacks to reduce the risk ofinjuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lapbelt snug and low ...

Pull lever up to adjust seatback. Using the manual lumbar support (if equipped) Turn the lumbar support controlclockwise to increase firmness. Turn the lumbar support controlcounterclockwise to increasesoftness. REAR SEATS Center facing jump seat (2 door SuperCab) (if equipped) To open, pull inboard...

Center facing jump seat (4 door SuperCab) (if equipped) To open, pull seat assembly down,then raise seatback. To stow the seat, fold seat backdown and raise seat assembly to thefully upright position. Do not install a child seat ina center facing jump seat. SAFETY RESTRAINTS Safety restraints precau...

In a rollover crash, an unbelted person is significantly more likelyto die than a person wearing a safety belt. Each seating position in your vehicle has a specific safety beltassembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on t...

The front outboard safety restraints in the vehicle are combination lapand shoulder belts. The front passenger outboard safety belt has twotypes of locking modes described below: Energy Management Feature • This vehicle has a seat belt system with an energy managementfeature at the front outboard se...

After any vehicle collision, the seat belt system at all outboardseating positions (except driver, which has no “automatic locking retractor” feature) must be checked by a qualified technician to verifythat the “automatic locking retractor” feature for child seats is stillfunctioning properly. In ad...

• Regular Cab and 4–door SuperCab • 2–door SuperCab To lower the shoulder belt height, push the button and slide the heightadjuster down. To raise the height of the shoulder belt, slide the heightadjuster up. Pull down on the height adjuster to make sure it is locked inplace. Position the safety bel...

Lap belts Adjusting the front center seat lap belt (if equipped) The lap belt does not adjust automatically. The lap belt should fit snugly and as low as possible around thehips, not across the waist. Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfr...

The lap belt should fit snugly and as low as possible around thehips, not across the waist. If you need to lengthen the belt, unfasten it and repeat the procedureabove. To unfasten the belt, push in the release button prior to opening the reardoor. Safety belt extension assembly If the safety belt i...

BeltMinder The BeltMinder feature is a supplemental warning to the safety beltwarning function. This feature provides additional reminders to thedriver that the driver’s safety belt is unbuckled by intermittentlysounding a chime and illuminating the safety belt warning lamp in theinstrument cluster....

Reasons given... Consider... “Belts areuncomfortable” We design our safety belts to enhance comfort. Ifyou are uncomfortable - try different positions forthe safety belt upper anchorage and seatbackwhich should be as upright as possible; this canimprove comfort. “I was in a hurry” Prime time for an ...

Deactivating/activating the BeltMinder feature Read steps 1 - 9 thoroughly before proceeding with thedeactivation/activation programming procedure. The BeltMinder feature can be deactivated/activated by performing thefollowing procedure: Before following the procedure, make sure that: • The parking ...

• This will disable BeltMinder if it is currently enabled, or enableBeltMinder if it is currently disabled. 7. Confirmation of disabling BeltMinder is provided by the safety beltwarning light flashing four times per second for three seconds. 8. Confirmation of enabling BeltMinder is provided by: • T...

The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion ...

• a readiness light and tone, • and the electrical wiring which connects the components. The RCM (restraints control module) monitors its own internal circuitsand the supplemental air bag electrical system warning (including thepassenger air bag deactivation switch, the impact sensors, the systemwir...

Passenger air bag ON/OFF switch An air bag ON/OFF switchhas been installed in this vehicle. Before driving, always look at the face of the switch tobe sure the switch is in the properposition in accordance with theseinstructions and warnings. Failureto put the switch in a properposition can increase...

Turning the passenger air bag back on The passenger air bag remains OFF until you turn it back ON. 1. Insert the ignition key and turnthe switch to ON. 2. The OFF light will brieflyilluminate when the ignition isturned to ON. This indicates thatthe passenger air bag is operational. If the OFF light ...

The vast majority of drivers and passengers are much safer with an airbag than without. To do their job and reduce the risk of life threateninginjuries, air bags must open with great force, and this force can pose apotentially deadly risk in some situations, particularly when a front seatoccupant is...

• causes the passenger air bag to pose a special risk for the passenger;and • makes the potential harm from the passenger air bag in a crashgreater than the potential harm from turning OFF the air bag andallowing the passenger, even if belted, to hit the dashboard orwindshield in a crash. This vehic...

3. Medical condition: A passenger has a medical condition that, according to his or her physician: • poses a special risk for the passenger if the air bag deploys; and • makes the potential harm from the passenger air bag deploymentgreater than the potential harm from turning OFF the air bag andexpe...

Always follow the instructions and warnings that come with any infant orchild restraint you might use. When possible, always place children under age 12 in the rear seat ofyour vehicle. Accident statistics suggest that children are safer whenproperly restrained in the rear seating positions than in ...

SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all of the manufacturer’s instructions with thesafety seat you put in your vehicle. If you do not install and use thesafety seat properly, the ...

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap whichgoes over the back of the seat and hooks to an anchoring point. Tetherstraps are available as an accessory for many older safety seats. Contactthe manufacturer of your child seat fo...

3. Locate the correct anchor for the selected seating position. The tether anchor is located on therear lower portion of the passengerseat. Seating and Safety Restraints 137

Center seating location When installing a child safety seat in the center position, route the tetherstrap over the center arm rest and clip it to the center anchor. Seating and Safety Restraints 139

Center seating location 60/40 vinyl seats When installing a child safety seat in the center position on a 60/40 vinylseat, route the tether strap through the guiding sleeve and clip it to thecenter anchor. If the tether strap is clipped incorrectly, the child safety seatmay not be retained properly ...

STARTING Positions of the ignition 1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 2. LOCK, locks the steering wheel,automatic transmission gearshiftlever and allows key removal. 3. OFF, shuts off the engine and allaccessories without lockin...

Do not start your vehicle in a closed garage or in other enclosedareas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions. If you smell exhaust fumes inside your vehicle, have your dealerinspe...

Starting the engine Note: Whenever you start your vehicle, release the key as soon as the engine starts. Excessive cranking could damage the starter. 1. Turn the key to 5 (START)without pressing the acceleratorpedal and release as soon as theengine starts. The key will return to4 (ON). 2. If the tem...

aggravated by environmental conditions such as cold, heat, moisture,road dust, salt or mud. If a “metal-to-metal,” “continuous grinding” or“continuous squeal” sound is present while braking, the brake liningsmay be worn-out and should be inspected by a qualified servicetechnician. If you are driving...

• The anti-lock system does not reduce stopping distance. Always leaveenough room between your vehicle and the vehicle in front of you tostop. • We recommend that you familiarize yourself with this brakingtechnique. However, avoid taking any unnecessary risks. ABS warning lamp ABS The ABS warning la...

The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released. Always set the parking brake fully and make sure that thegearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual t...

If the steering wanders or pulls, the condition could be caused by any ofthe following: • underinflated tire(s) on any wheel(s) • uneven vehicle loading • high crown in center of road • high crosswinds • wheels out of alignment • loose or worn suspension components TRACTION-LOK AXLE (IF EQUIPPED) Th...

Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any morethan low-slung sports cars are desig...

Do not drive your vehicle until you verify that the brakelampsare working. If your vehicle gets stuck in mud or snow it may be rocked out byshifting from forward and reverse gears, stopping between shifts, in asteady pattern. Press lightly on the accelerator in each gear. Do not rock the vehicle if ...

Understanding gearshift positions Hold the brake pedal down while you move the gearshift leverfrom P (Park) to another position. If you do not hold the brake pedal down, your vehicle may move unexpectedly and injure someone. P (Park) To put your vehicle in gear, start the engine, depress the brake p...

(Overdrive) can be deactivated by pressing the transmission controlswitch on the end of the gearshiftlever. The transmission control indicatorlight (TCIL) will illuminate on theinstrument cluster. Drive – Not shown on the display. Activate by pressing the transmission control switch on the end of th...

1 (First) Use 1 (First) to provide maximumengine braking on steepdowngrades. Upshifts can be madeby shifting to 2 (Second) or to(Overdrive). Selecting 1 (Low) athigher speeds causes the transmission to shift to a lower gear and willshift to 1 (First) after the vehicle decelerates to the proper vehic...

PARKING 1. Apply the brake and shift into N(Neutral). 2. Engage the parking brake. 3. Shift into 1 (First). 4. Turn the ignition to Off. Do not park your vehicle in Neutral, it may move unexpectedlyand injure someone. Use 1 (First) gear and set the parking brake fully. Driving 155

Shifting from 2H (2WD high) to 4H (4WD high) Move the transfer case lever to 4H(4WD High) at a stop or anyforward speed up to 88 km/h(55 mph). • At temperatures below 0°C(32°F), shifts from 2H (2WDHigh) to 4H (4WD High) shouldnot be performed above 72 km/h(45 mph). Do not shift into 4H (4WD High) wi...

Shifting from 4L (4WD low) to 4H (4WD high) or 2H (2WD high) 1. Bring the vehicle to a complete stop. 2. Depress the brake. 3. Depress the clutch. 4. Move the transfer case shift leverthrough N (Neutral) directly to 4H(4WD High) or 2H (2WD high) andhold the shift lever in position untilthe transfer ...

Shifting from 2WD (2WD high) to 4X4 HIGH (4WD high) Move the 4WD control to the 4X4HIGH position. Do not shift into 4X4 HIGH withthe rear wheels slipping. Shifting from 4X4 HIGH (4WD high) to 2WD (2WD high) Move the 4WD control to 2WDposition at any forward speed. • You do not need to operate the ve...

Shifting from 4X4 LOW (4WD low) to 2WD (2WD high) 1. Bring the vehicle to a stop. 2. Depress the brake. 3. Place the gearshift in N (Neutral) (automatic transmission) or depressthe clutch (manual transmission). 4. Move the 4WD control to the2WD position. Shifting between 4X4 HIGH (4WD high) and 4X4 ...

4WD Systems 4WD (when you select a 4WD mode) uses all four wheels to power thevehicle. This increases traction, enabling you to drive over terrain androad conditions that a conventional two-wheel drive vehicle can’t. Power is supplied to all four wheelsthrough a transfer case. On 4WDvehicles, the tr...

Mud and water If you must drive through highwater, drive slowly. Traction orbrake capability may be limited. When driving through water,determine the depth; avoid waterhigher than the bottom of the hubs(if possible) and proceed slowly. Ifthe ignition system gets wet, thevehicle may stall. Once throu...

“Tread Lightly” is an educationalprogram designed to increase publicawareness of land-use regulationsand responsibilities in our nationswilderness areas. Ford joins the U.S.Forest Service and the Bureau of Land Management in encouraging youto help preserve our national forest and other public and pr...

Descend a hill in the same gear youwould use to climb up the hill toavoid excessive brake applicationand brake overheating. Do notdescend in neutral, disengageoverdrive or manually shift to alower gear. When descending asteep hill, avoid sudden hardbraking as you could lose control.When you brake ha...

information on the operation of the anti-lock brake system. Never drive with chains on the front tires of 4WD vehicles without alsoputting them on the rear tires. This could cause the rear to slide andswing around during braking. Tires, Replacement Requirements 4WD vehicles are equipped with tires d...

Each day before you drive, checkyour tires. If one looks lower thanthe others, use a tire gauge to checkpressure of all tires, and adjust ifrequired. Check tire pressure with atire gauge every few weeks(including spare). Safe operationrequires tires that are neitherunderinflated nor overloaded. Peri...

determined by subtracting the vehicle curb weight for eachengine/transmission combination, any required option weight for trailertowing and the weight of the driver from the GCWR for the towingvehicle. • Maximum Trailer Weight: Maximum weight of a trailer the loaded vehicle (including occupants and ...

Special loading instructions for owners of pickup trucks andutility-type vehicles For important information regarding safe operation of this typeof vehicle, see the Preparing to drive your vehicle section in this chapter. Loaded vehicles, with a higher center of gravity, may handledifferently than u...

Towing trailers beyond the maximum recommended gross trailerweight could result in engine damage, transmission/axle damage, structural damage, loss of control, and personal injury. Preparing to tow Use the proper equipment for towing a trailer, and make sure it isproperly attached to your vehicle. S...

Refer to the following chart for information regarding thefactory-equipped trailer tow connector: Trailer tow connector Color Function Comment 1. Dark Green Trailer right-handturn signal Circuit activated when brakepedal is depressed or whenignition is on and right-handturn signal is applied. 2. Yel...

Trailer towing tips • Practice turning, stopping and backing up before starting on a trip toget the feel of the vehicle trailer combination. When turning, makewider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached. • The tra...

4X2 AND 4X4 VEHICLES EQUIPPED WITH MANUALTRANSMISSIONS Before you have your vehicle towed: • Release the parking brake. • Move the gearshift to N (Neutral). • Turn the key in the ignition to the OFF/UNLOCKED position. • The maximum recommended speed is 88 km/h (55 mph). • The maximum recommended dis...

GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the New Vehicle Limited...

FUSES AND RELAYS Fuses If electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check the appropriatefuses before replacing any electricalcomponents. Note: Always replace a fuse with one that has the specified amperage r...

Passenger compartment fuse panel The fuse panel is located on theleft-hand side of the instrumentpanel facing the driver’s side door.Pull the panel cover outward toaccess the fuses. To remove a fuse use the fuse puller tool provided on the fuse panelcover. Roadside Emergencies 188

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 34 — Not Used 35 15A or Not Used 15A: Horn Relay if Not Equipped withTruck Central Security Module 36 — Not Used Power distribution box The power distribution box islocated in the engine compartment.The power distributi...

If you use the temporary spare tire continuously or do not followthese precautions, the tire could fail, causing you to lose control of the vehicle, possibly injuring yourself or others. When driving with the temporary spare tire do not: • exceed 80 km/h (50 mph) or drive further than 3 200 km(2 000...

Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the followinglocations: Tool Location Spare tire Under the vehicle, just forward ofthe rear bumper Jack, jack handle, wheel nut wrench Regular Cab: behind seats andunderneath the jack and toolscover SuperCab...

2. If equipped, unlock and removethe spare tire carrier lock from therear access hole located just abovethe rear bumper and below thetailgate. 3. Insert the straight end of the jackhandle into the rear access holelocated just above the rear bumperand below the tailgate. Forward motion will stop andr...

Stowing the spare tire 1. Lay the tire on the ground with the valve stem facing up. 2. Install the retainer through thewheel center and slide the wheelunder the vehicle. 3. Turn the spare handle clockwiseuntil the tire is raised to its originalposition underneath the vehicle. Thespare handle ratchet...

3. Block the diagonally oppositewheel. 4. Insert tapered end of the lugwrench behind hub caps and twistthem off. 5. Loosen each wheel lug nutone-half turn counterclockwise butdo not remove them until the wheelis raised off the ground. 6. Position the jack according to thefollowing guides and turn th...

10. Remove the jack and fullytighten the lug nuts in the ordershown. 11. Stow the flat tire. Refer to Stowing the spare tire. 12. Stow the jack and lug wrench.Make sure the jack is fastened so itdoes not rattle when you drive. 13. Unblock the wheels. JUMP STARTING YOUR VEHICLE The gases around the b...

4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect any electricalsurges. Turn all other accessories off. Connecting the jumper cables 1. Connect the po...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingbelt. Ford Motor Company has notapproved a ...

GETTING THE SERVICES YOU NEED At home Ford Motor Company and Ford of Canada have authorized dealerships toservice your vehicle. It is preferred that you return to the Ford dealerwhere your vehicle was purchased when warranty repairs are needed.However, you may also take your vehicle to another Ford ...

In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action un...

THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes • available free to owners and lessees of qualifying Ford Motor Companyvehicles The Dispute Settlement Board may not be available in all states. FordMotor...

Board membership The Board consists of: • three consumer representatives • a Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained byan independent consulting firm. The dealership Board member is chosenfrom Ford and Lincoln Mercury deale...

You will receive a letter of explanation if your application does notqualify for Board review. Oral presentations If you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral presentationbefore the Board, this is not a requireme...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) In those cases where you continue to feel that the efforts by Ford andthe dealer to resolve a factory-related vehicle service concern have beenunsatisfactory, Ford of Canada participates in an impartial third partymediation/arbitration program...

If your vehicle must be serviced while you are traveling or living inCentral or South America, the Caribbean, or the Middle East, contact thenearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANYWORLDWIDE DIRECT MARKET OPERATIONS1555 Fairlane DriveFairlane Busi...

WASHING THE EXTERIOR OF YOUR VEHICLE Never wash a vehicle that is “hot tothe touch” or during exposure tostrong, direct sunlight. It isrecommended that you wash yourvehicle regularly with cool orlukewarm water and a neutral Phshampoo, such as Detail Wash(ZC-3–A), which is available fromyour authoriz...

CLEANING THE ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • The engine must be cool to the touch before spraying with water. • Never spray a hot engine with cold water, as damage to theengine block or engine co...

• 4.0L SOHC V6 engine • Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage. WASHING NON-PAINTED PLASTIC EXTERIOR PARTS Use Detail Wash (ZC-3–A) for routine cleaning. If tar or grease spots are present, clean with Extra Strength Tar andRoad Oil Re...

Use a soft cloth and a solution of Triple Clean (EOAZ-19526–AA), mixedproperly with water, in order to remove bug residue. If tar or greasespots are present, clean with Extra Strength Tar and Road Oil Removal(B7A-19520–AA). CLEANING THE WINDSHIELD, WIPER BLADES AND REARWINDOW If the wiper does not w...

CLEANING AND MAINTAINING THE SAFETY BELTS Clean the safety belts with Extra Strength Upholstery Cleaner(E8AZ-19523–AA), available from your authorized Ford, Lincoln orMercury dealer. Do not use bleach, dye or any other solvent to clean the belts, asthese actions may weaken the belt webbing. UNDERBOD...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a scheduled maintenance guide which makes trackingroutine service easy. If your vehicle requires professional service, your dealership can providethe...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Windshield washer fluid reservoir 2. Engine coolant reservoir 3. Engine oil dipstick 4. Transmission fluid dipstick (automatic transmission) 5. Engine oil filler cap 6. Brake fluid reservoir 7. Power distribution box 8. Clutch fluid ...

WINDSHIELD WASHER FLUID Washer fluid Check the washer fluid wheneveryou stop for fuel. The reservoir ishighlighted with a symbol. If the level is low, add enough fluidto fill the reservoir. In very coldweather, do not fill the reservoir allthe way. Only use a washer fluid that meets Ford specificati...

6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is between the MIN and MAX marks, the oil level is acceptable, DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough oil to raise the levelwithin the MIN-MAX range. • 2.3L I4 engine • 3.0L...

• 4.0L SOHC V6 engine • Oil levels above the MAX mark may cause engine damage. Some oilmust be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in...

Engine Oil Recommendations 2.3L & 3.0L Engines Look for this certificationtrademark. SAE 5W-20 engine oil is recommended. Change your engine oil and filter according to the appropriate schedulelisted in the scheduled maintenance guide. Do not use supplemental engine oil additives, oil treatments...

If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trouble-free operation, keep the top of the battery clean anddry. Also, make certain the battery cables are always tightly fastened tothe battery terminals. If you see any corro...

2. Put the gearshift in P (Park), turn off all accessories and start theengine. 3. Run the engine until it reaches normal operating temperature. 4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine to idle for at least one minute. 6. Drive the vehicle to compl...

testing is possible with a hydrometer or antifreeze tester (such as theRotunda Battery and Antifreeze Tester, 014–R1060). The level of coolantshould be maintained at the “cold full” of “cold fill range” level in thecoolant reservoir. If the level falls below, add coolant per the instructionsin the A...

When the engine is cold, check the level of the engine coolant in thereservoir. • The engine coolant should be at the “cold fill level” or within the “coldfill range” as listed on the engine coolant reservoir (depending uponapplication). • Refer to the Scheduled Maintenance Guide for service interva...

Oregon), depending on the type of coolant originally equippedin your vehicle. If you are unsure which type of coolant your vehicle requires, check your coolant reservoir or contact your local dealer. Note: Use of Motorcraft Cooling System Stop Leak Pellets, VC-6, darkens the color of Motorcraft Prem...

To reduce the risk of personal injury, make sure the engine iscool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come outforcefully when the cap is loosened slightly. 1. Before you begin, turn the engine off and let it cool. 2. When...

specification ESE-M97B44–A. Use of such coolant may harm the engineand cooling system components. Ford Motor Company does NOT recommend the use of recycled enginecoolant in vehicles originally equipped with Motorcraft Premium GoldEngine Coolant since a Ford-approved recycling process is not yetavail...

• Decreased engine coolant concentrations below 40% willdecrease the freeze protection characteristics of the enginecoolant and may cause engine damage. • Refer to the chart on the coolant container to ensure thecoolant concentration in your vehicle will provide adequateprotection at the temperature...

Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materialsand any open flames beforefueling your vehicle. • Always turn off the vehicle beforefueling. • Automotive fuels can be harmfulor fatal if swallowed. Fuel such asgasoline is highly toxic and ifswallowed ...

The flow of fuel through a fuel pump nozzle can produce staticelectricity, which can cause a fire if fuel is pumped into an ungrounded fuel container. Use the following guidelines to avoid static build-up when filling anungrounded fuel container: • Place approved fuel container on the ground. • DO N...

more pronounced. If the problems persist, see your dealer or a qualifiedservice technician. It should not be necessary to add any aftermarket products to your fueltank if you continue to use high quality fuel of the recommended octanerating. Aftermarket products could cause damage to the fuel system...

• Use the same side of the same pump and have the vehicle facing thesame direction each time you fill up. • Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completel...

• Sudden or hard accelerations may reduce fuel economy. • Slow down gradually. • Driving at reasonable speeds (traveling at 88 km/h [55 mph] uses 15%less fuel than traveling at 105 km/h [65 mph]). • Revving the engine before turning it off may reduce fuel economy. • Using the air conditioner or defr...

• Fuel economy may decrease with lower temperatures during the first12–16 km (8–10 miles) of driving. • Driving on flat terrain offers improved fuel economy as compared todriving on hilly terrain. • Transmissions give their best fuel economy when operated in the topcruise gear and with steady pressu...

Allow the vehicle to sit for at least eight hours without starting theengine. Then, start the engine and complete the above driving cycle. Theengine must warm up to its normal operating temperature. Once started,do not turn off the engine until the above driving cycle is complete. CHECKING AND ADDIN...

BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked andrefilled as needed. Refer to thescheduled maintenance guide forthe service interval schedules. 1. Clean the reservoir cap beforeremoval to prevent dirt or waterfrom entering the reservoir. 2. Visually inspect the fluid leve...

CLUTCH FLUID (IF EQUIPPED) Check the fluid level. Refer to the scheduled maintenance guide for theservice interval schedules. During normal operation, the fluid level in the clutch reservoir shouldremain constant. If the fluid level drops, refill the fluid level to the stepin the reservoir. Use only...

Automatic transmission fluid expands when warmed. To obtain anaccurate fluid check, drive the vehicle until it is at normal operatingtemperature (approximately 30 km [20 miles]). If your vehicle has beenoperated for an extended period at high speeds, in city traffic during hotweather or pulling a tr...

The transmission fluid should be inthis range if at normal operatingtemperature (66°C-77°C[150°F-170°F]). The transmission fluid should be inthis range if at ambient temperature(10°C-35°C [50°F-95°F]). High fluid level Fluid levels above the safe rangemay result in transmission failure.An overfill c...

Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug andinspect the fluid level. 3. Fluid level should be at bottom ofthe opening. 4. Add enough fluid through thefiller opening so that the fluid levelis at the bottom of the opening. 5. Insta...

Checking and adding transfer case fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug andinspect the fluid level. 3. Add only enough fluid throughthe filler opening so that the fluidlevel is at the bottom of theopening. Use only fluid that meets Ford specifications. Refer to Lubr...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B, and C, representing thetire’s resistance to the gen...

Tire rotation Because your vehicle’s tires perform different jobs, they often weardifferently. To make sure your tires wear evenly and last longer, rotatethem as indicated in the scheduled maintenance guide. If you notice thatthe tires wear unevenly, have them checked. The following procedure applie...

• Five tire rotation Replacing the tires Replace the tires when the wearband is visible through the tiretreads. When replacing full size tires, never mix radial bias-belted, orbias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same s...

Do not replace your tires with “high performance” tires or largersize tires. Failure to follow these precautions may adversely affect thehandling of the vehicle and make it easier for the driver to lose control and roll over. Tires that are larger or smaller than your vehicle’s original tires may al...

• The suspension insulation and bumpers will help prevent vehicledamage. Do not remove these components from your vehicle whenusing snow tires and chains. MOTORCRAFT PART NUMBERS Component 2.3L I4 engine 3.0L V6 engine 4.0L V6 engine Air filterelement FA-1658 FA-1658 FA-1658FA-1665 (FX4 only) Fuel f...

Fluid Ford PartName Application Capacity Brake fluid andClutch fluid Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeFluid All Fill to line orstep (for clutch)on reservoir Power steeringfluid MotorcraftMERCON t ATF All Fill to range ondipstick orreservoir Transmissionfluid 1 MotorcraftMERCON t ATF...

Fluid Ford PartName Application Capacity Engine coolant 4 MotorcraftPremium EngineCoolant(green-colored) or Motorcraft Premium GoldEngine Coolant(yellow-colored) 2.3 L I4 enginewith manualtransmission 10.0L(10.5 quarts) 2.3L I4 enginewith automatictransmission 9.7L(10.2 quarts) 3.0L V6 enginewith ma...

LUBRICANT SPECIFICATIONS Item Ford partname orequivalent Ford partnumber Fordspecification Front axle(4X4) MotorcraftSAE 80W-90Premium RearAxle Lubricant XY-80W90-QL WSP-M2C197-A Rear axle MotorcraftSAE 80W-90Premium RearAxle Lubricant 1 XY-80W90-QL WSP-M2C197-A Brake fluid andclutch fluid (ifequipp...

Item Ford partname orequivalent Ford partnumber Fordspecification Engine oil 2.3L and 3.0Lengines MotorcraftSAE 5W-20Super PremiumMotor Oil XO-5W20-QSP WSS-M2C153-Hand APICertificationMark 4.0L engines MotorcraftSAE 5W-30Super PremiumMotor Oil XO-5W30-QSP WSS-M2C205–Aand APICertificationMark Hinges,...

VEHICLE DIMENSIONS Vehicledimensions Regular CabShort WheelBase (SWB) mm(in) Regular CabLong WheelBase (LWB)mm (in) Supercab mm(in) (1) Overalllength 4 763 (187.5) 5 093 (200.5) 5 153 (202.9) (2) Overallwidth 1 785 (70.3) 1 785 (70.3) 1 785 (70.3) (3) Overallheight 4x2/4x4 1 593.5 (62.7) /1 655 (65....

FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of genuine Ford accessories are available for yourvehicle through your local authorized Ford, Lincoln Mercury or Ford ofCanada dealer. These quality accessories have been specificallyengineered to fulfill your automotive needs; they are custom desig...

A ABS (see Brakes) .....................146 Air bag supplemental restraintsystem ........................................121 and child safety seats ............123description ..............................121disposal ....................................125driver air bag ..........................123...

Limited slip axle(see Traction Loc) ....................149 Load limits .................................170 GAWR ......................................170GVWR ......................................170trailer towing ..........................170 Loading instructions .................172 Lubricant sp...

W Warning chimes ...........................14 Warning lights (see Lights) .......10 Washer fluid ..............................233 Water, Driving through .............169 Windows power .........................................84 Windshield washer fluid andwipers checking and adding fluid .....233ch...