Ford 2002 Ranger v.1- Manuals

Special instructions For your safety, your vehicle is fitted with sophisticated electroniccontrols. By operating other electronic equipment (e.g. mobile telephonewithout exterior aerial) electromagnetic fields can occur which can cause malfunctions of the vehicle electronics. Therefore you shouldobs...

Using your vehicle with a snowplow Do not use this vehicle for snowplowing. Using your vehicle as an ambulance Do not use this vehicle as an ambulance. Your vehicle is not equipped with the Ford Ambulance PreparationPackage. Electric vehicles For information on operating your Electric Vehicle, also ...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat InstallationWarning Child Seat TetherAnchorage Brake System Anti-Lock Brake System Brake Fluid -Non-Petroleum Based Tr...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

These temporary malfunctions can be corrected by filling the fuel tankwith high quality fuel of the recommended octane and/or properlyinstalling and securely tightening the fuel cap. After three driving cycleswithout these or any other temporary malfunctions present, the lightshould turn off. (A dri...

Anti-lock brake system (ABS) Momentarily illuminates at start upto ensure the circuit is functional. Ifthe light does not illuminate,remains on or continues to flash, theABS needs to be serviced (refer to Brakes in the Driving chapter for more information). With the ABS light on, the ABS is disabled...

It may take a long period of time for the system to detect animproperly installed fuel filler cap. For more information, refer to Fuel filler cap in the Maintenance and specifications chapter. Speed control Illuminates when the speed controlis activated. O/D off (if equipped) Illuminates when the ov...

Anti-theft system (if equipped) Refer to SecuriLock y passive anti-theft system in the Locks and Security chapter. Four wheel drive high (if equipped) Illuminates when four-wheel drivelow is put in high range. If the lightcontinues to flash have the systemserviced. Four wheel drive low (if equipped)...

GAUGES Engine coolant temperature gauge Indicates the temperature of theengine coolant. At normal operatingtemperature, the needle remainswithin the normal area (the areabetween the “H” and “C”). If it enters the red section, theengine is overheating. Stop thevehicle as soon as safelypossible, switc...

Engine oil pressure gauge Indicates engine oil pressure. Atnormal operating temperature, theneedle will be in the normal range(the area between the “L” and “H”);if the needle goes below the normalrange, stop the vehicle as soon assafely possible and switch off theengine immediately. Check the oillev...

Speedometer Indicates the current vehicle speed. Odometer Registers the total kilometers(miles) of the vehicle. Trip odometer Registers the kilometers (miles) ofindividual journeys. To reset,depress the control. Tachometer Indicates the engine speed inrevolutions per minute. Driving with your tachom...

AM/FM STEREO Volume/power control Press the control to turn the audiosystem on or off. Turn the control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition switch is turned bac...

AM/FM select The AM/FM select control works inradio mode. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press thecontrol to switch between AM, FM1 or FM2 memory preset stations. Tune adjust The tune control works in radio mode. Tune adjust in radio mode • Pre...

Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns,indicating the station is held in memor...

Setting the clock Press CLK to toggle betweenlistening frequencies and clockmode. To set the hour, press and hold theCLK control until CLOCK SETappears in the display and press theSEEK control: • to decrease hours and • to increase hours. To set the minute, press and holdthe CLK control until CLOCK ...

AM/FM select The AM/FM select control works inradio and CD modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press thecontrol to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in CD mode Press this control to stop CD play and begin radi...

Seek function The seek function control works in radio or CD mode. Seek function in radio mode • Press to find the next listenable station down thefrequency band. • Press to find the next listenable station up thefrequency band. Seek function for CD mode • Press to seek to the previous track of the ...

Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns,indicating the station is held in memor...

Speaker balance adjust Speaker sound distribution can beadjusted between the right and leftspeakers. Speaker fade adjust Speaker sound can be adjustedbetween the front and rearspeakers. CD select • To begin CD play (if CD[s] areloaded), press the CD control.The first track of the disc willbegin play...

Rewind The rewind control works in CD and CD changer (if equipped) modes. To rewind in CD mode press the CDcontrol (preset 1). Pressing the control for less thanthree seconds results in slowrewind. Pressing the control for more than three seconds results in fastrewind. Fast forward The fast forward ...

Setting the clock Press CLK to toggle betweenlistening frequencies and clockmode while in radio mode. To set the hour, press and hold theCLK control. Press the SEEK control: • to decrease hours and • to increase hours. To set the minute, press and holdthe CLK control. Press the TUNE control: • to de...

MACH T MP3 MUSIC SYSTEM 1. ON/OFF and volume control 2. AM/FM control 3. Bass control 4. Treble control 5. Fade control 6. Balance control 7. Seek control 8. Scan controlat 9. Clock control 10. Tune/Directory control 11. CD control 12. MP3 directory control 13. Eject control 14. CD rewind control 15...

MP3 functions Your audio system is equipped with MP3 capability which allows you tolisten to songs in MP3 flat file mode and MP3 directory mode. To engage MP3 flat file mode, insert an MP3 disc. If an MP3 disc isalready present in the player, press the CD control. The MP3 icon willdisplay while the ...

Radio station memory preset The radio is equipped with six station memory preset controls. Thesecontrols can be used to select up to six preset AM stations and twelveFM stations (six in FM1 and six in FM2). Setting memory preset stations 1. Select the frequency band withthe AM/FM select control. 2. ...

Bass adjust The bass adjust control allows youto increase or decrease the audiosystem’s bass output. Treble adjust The treble adjust control allows youto increase or decrease the audiosystem’s treble output. Speaker balance adjust Speaker sound distribution can beadjusted between the right and lefts...

Playing a CD • If a CD is already loaded, pressthe CD control. CD play willbegin where it stopped last. • If a CD is not already loaded,insert the CD into the system. CD will briefly appear in the displayand then the first track on the disc will begin playing. Playing an MP3 disc in MP3 flat file mo...

Compression feature The compression feature works in CD, MP3 flat file mode and MP3directory mode. Compression adjust brings soft andloud CD passages together for amore consistent listening level. Press the COMP control to activate compression adjust. The compressionicon (c) will illuminate in the d...

Shuffle feature in MP3 flat file mode The shuffle feature in MP3 flat file mode allows you to play all the trackson the MP3 disc in random order. • Press the SHUFFLE control toengage random play. SHF andthen ON will briefly appear in thedisplay. The player will thenbegin random play. • To select ano...

• To select another random track inthe current directory, pressor on the SEEK control. • Press the SCN control to scanthrough random tracks in thecurrent directory. The tracknumber will flash in the display.The shuffle feature will remainenabled. To shuffle tracks in anotherdirectory, press or on th...

Seek function in CD mode • Press to seek to the previous track of the disc. • Press to seek forward to the next track of the current disc.After the last track has beencompleted, the first track of thecurrent disc will automatically replay. Scan function The scan function works in radio,tape or CD mo...

2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns,indicating the station is held in memory on the control you selected. Autoset memory preset Autoset allows you to set strong radio...

Bass adjust The bass adjust control allows youto increase or decrease the audiosystem’s bass output. Press the BASS control then press: • to decrease the bass output and • to increase the bass output. Treble adjust The treble adjust control allows youto increase or decrease the audiosystem’s treble ...

Speaker fade adjust Speaker sound can be adjustedbetween the front and rearspeakers. Press the FADE control then press: • to shift the sound to the front and • to shift the sound to the rear. Tape select • To begin tape play (with a tapeloaded into the audio system)while in the radio or CD mode,pres...

Fast forward The fast forward control works intape and CD modes. • In the tape mode, tape directionwill automatically reverse whenthe end of the tape is reached. • In CD mode, pressing the control fast forwards the CD within thecurrent track. Tape direction select Press SIDE 1–2 to play the alternat...

Compression adjust Compression adjust brings soft andloud CD passages together for amore consistent listening level. Press the COMP control to activateand deactivate compression adjust. Shuffle feature The shuffle feature operates in CDmode and plays all tracks in randomorder. Press the SHUFFLE cont...

To set the minute, press and holdthe CLK control and press TUNE: • to decrease minutes and • to increase minutes. If your vehicle has a separate clock,(other than the digital radiodisplay), the CLK control will notfunction in the above manner. The CLK control will allow you toswitch between media di...

PREMIUM AM/FM STEREO IN DASH SIX CD RADIO Volume/power control Press the control to turn the audiosystem on or off. Turn the control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when the...

Radio station memory preset The radio is equipped with six station memory preset controls. Thesecontrols can be used to select up to six preset AM stations and twelveFM stations (six in FM1 and six in FM2). Setting memory preset stations 1. Select the frequency band with the AM/FM select control. Pr...

To deactivate autoset and return to your audio system’s manually setmemory stations, press the AM/FM control again. CD select CD mode may be entered bypressing the CD control and theLOAD control. Load the CD into theaudio system. The first track of thedisc will begin playing. After that,CD play will...

Press the LOAD control. (You can choose which slot will be loaded bypressing the desired preset number. If you do not choose a slot, the systemwill choose the next available one.) Wait until the CD door opens. Load theCD into the player. LOADING CD# is displayed. When the CD has beenloaded, the door...

Traffic announcements This feature allows you to heartraffic announcements. When in thismode, traffic announcements willinterrupt radio and CD play. When in FM mode and RDS isactivated, press the MENU until TRAFFIC OFF displays. Press the SELcontrol to engage the feature. The display will read TRAFF...

Radio data system (RDS) feature This feature allows your audiosystem to receive text informationfrom RDS-equipped FM radiostations. To activate RDS: • When in FM mode, press the MENU control until RDS OFF displays. • Press the SEL control to engage this feature (RDS ON). RDS features: Once the RDS f...

• Disc finalization — The disc may be left open for the purpose ofadding sessions to it at a later time, but be sure to close each sessionor the disc will not play. • Bit rate — The player supports bit rates from 56–320 kbps, as well asvariable bit rate MP3 files, but lower bit rates will have a not...

• Station overload. Weak signals are sometimes captured by stronger signals when you pass a broadcast tower. A stronger signal maytemporarily overtake a weaker signal and play while the weak stationfrequency is displayed. The audio system automatically switches to single channel reception if itwill ...

HEATER ONLY SYSTEM (IF EQUIPPED) Fan speed control Controls the volume of air circulatedin the vehicle. Temperature control knob Controls the temperature of theairflow inside the vehicle. Onheater-only systems, the air cannotbe cooled below the outsidetemperature. Mode selector control Controls the ...

Operating tips • In humid weather, place the climate control system in DEF beforedriving. This will reduce fogging on your windshield. Once thewindshield has been cleared, select any desired position. • To reduce humidity buildup inside the vehicle, do not drive with theclimate control system in the...

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED) Fan speed control Controls the volume of air circulatedin the vehicle. Temperature control knob Controls the temperature of theairflow inside the vehicle. Mode Selector Control Controls the direction of the airflowto the inside of the vehicle. ...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parkinglamps. Rotate to the second positionto turn on the headlamps. Foglamp control (if equipped) The foglamps can be turned onwhen the headlamp control is ineither of the following positions: • Parking lamps • Low bea...

High beams • Push forward to activate. • Pull toward you to deactivate. Flash to pass Pull toward you to activate andrelease to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of theinstrument panel during headlampand parklamp operation. • Rotate up to brighten. • Rotate down to dim. •...

Replacing the interior bulbs Check the operation of the following interior bulbs frequently: • interior overhead lamp • map lamp For bulb replacement, see a dealer or qualified technician. Replacing headlamp bulbs To remove the headlamp bulb: 1. Make sure headlamp switch is inOFF position, then open...

6. Without turning, remove the oldbulb by gently pulling it straightback out of the lamp assembly. To install the new bulb: Handle a halogen headlamp bulb carefully and keep out ofchildren’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause...

Replacing front side marker bulbs 1. Open the hood. 2. Remove two screws and cover (ifequipped). 3. At the back of the headlamp, pryup the two retainer pins to releasethe headlamp assembly from thevehicle and pull headlamp forward. 4. Remove screw(s) from lampassembly. 5. Disengage lamp assembly (it...

6. Rotate bulb socketcounterclockwise and remove fromlamp assembly. 7. Carefully pull bulb straight out ofsocket and push in the new bulb. 8. Install the bulb socket in lampassembly by turning clockwise. 9. Align the lamp on the vehicle andpush to snap in place. 10. Install screw(s) on lamp assembly...

3. Rotate bulb socketcounterclockwise turn and removefrom lamp assembly. 4. Carefully pull the bulb straightout of the socket and push in thenew bulb. 5. Install the bulb socket in lampassembly by turning clockwise. 6. Install the lamp assembly andsecure with four screws. Replacing foglamp bulbs 1. ...

To remove the brakelamp assembly: 1. Remove the two screws and lampassembly from vehicle. 2. Remove the bulb socket fromlamp assembly by rotating itcounterclockwise. 3. Carefully pull bulb straight out ofsocket and push in the new bulb. To install the brakelamp assembly: 1. Install the bulb socket i...

WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper controlto the desired interval, low or highspeed position. The bars of varying length are forintermittent wipers. When in thisposition rotate the control upwardfor fast intervals and downward forslow intervals. Push (tap) the end of the st...

Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from thewindshield and lock into the serviceposition. 2. Turn the blade at an angle fromthe wiper arm. Push the lock pinmanually to release the blade andpull the wiper blade down towardthe windshield to remove it from ...

Never adjust the steering wheel when the vehicle is moving. AUXILIARY POWER POINT Power outlets are designed for accessory plugs only. Do not hangany type of accessory or accessory bracket from the plug.Improper use of the power outlet can cause damage not coveredby your warranty. The auxiliary powe...

POWER WINDOWS (IF EQUIPPED) Press and hold the rocker switches to open and close windows. • Press the top portion of therocker switch to close. • Press the bottom portion of therocker switch to open. One touch down • Press AUTO completely down andrelease quickly. The driver’swindow will open fully. ...

POWER SIDE VIEW MIRRORS (IF EQUIPPED) To adjust your mirrors: 1. Select to adjust the left mirror or to adjust the right mirror. 2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the center position tolock mirrors in place. SPEED CONTROL (IF EQUIPPED) To turn speed contro...

To turn speed control off • Press OFF or • Turn off the vehicle ignition. Once speed control is switched off,the previously programmed setspeed will be erased. To set a speed • Press SET ACC. For speedcontrol to operate, the speedcontrol must be ON and thevehicle speed must be greaterthan 48 km/h (3...

To disengage speed control • Depress the brake pedal or • Depress the clutch pedal (ifequipped). Disengaging the speed control willnot erase the previouslyprogrammed set speed. Fullydepressing the clutch pedal maycause a flare in engine RPM as thethrottle is returned to idle. This isnormal. Pressing...

To return to a previously set speed • Press RSM. For RSM to operate,the vehicle speed must be fasterthan 48 km/h (30 mph). Indicator light This light comes on when either theSET ACCEL or RES controls arepressed. It turns off when the speedcontrol OFF control is pressed, thebrake or clutch is applied...

To return to normal overdrive mode,press the Transmission ControlSwitch again. The TCIL will nolonger be illuminated. When you shut off and re-start yourvehicle, the transmission will automatically return to normal(Overdrive) mode. For additional information about the gearshift lever and the transmi...

BED EXTENDER (IF EQUIPPED) Your vehicle may be equipped with a bed extender designed to extendthe pickup box for longer loads. To extend the bed extender: 1. Lower tailgate. 2. Pull the round knobs on each sideof the extender to release it fromthe pickup box. 3. Pivot extender on to the tailgate. Dr...

To remove the bed extender: 1. Extend the bed extender. 2. Pull the round knobs on each sideof the extender to unlock it. Make sure the locking clip screwsare loose before removing theextender. 1. Press the locking clips below themiddle bar on each side and lift theextender out of the bed. To instal...

To stow the rear panel: • Before driving with the tonneaucover open, stow the rear panel. • Release four cylinder clips andremove two hydraulic cylindersfrom the pickup box and rearpanel. • Lift the rear panel up, lay it ontop of the front panel and secureit with the two straps on thefront panel tie...

KEYS The key operates all locks on yourvehicle. In case of loss, replacementkeys are available from your dealer. You should always carry a secondkey with you in a safe place in caseyou require it in an emergency. Refer to SecuriLock y Passive Anti-Theft System for more information. POWER DOOR LOCKS ...

The remote entry features only operate with the ignition in the LOCKposition. If there is any potential remote keyless entry problem with your vehicle,ensure ALL key fobs (remote entry transmitters) are brought to the dealership, to aid in troubleshooting. Unlocking the doors Press this control to u...

Deactivating/activating power door lock disable feature 1. Turn the ignition key to ON, thenpress the UNLOCK button 3 times. 2. Turn the ignition key to OFF,then press the UNLOCK button 3times. 3. Turn the ignition key to ON,within five seconds press the LOCKbutton 2 times. The user should receive 2...

To replace the battery: 1. Twist a thin coin between the twohalves of the transmitter near thekey ring. DO NOT TAKE THEFRONT PART OF THETRANSMITTER APART. 2. Place the positive (+) side of newbattery in the same orientation.Refer to the diagram inside thetransmitter unit. 3. Snap the two halves back...

To program the transmitters yourself: • Place the key in the ignition andturn from 2 (LOCK) to 3 (OFF)and cycle between 3 (OFF) and4(ON) eight times in rapidsuccession (within 10 seconds)with the eighth turn ending in the4 (ON) position. The doors willlock/unlock to confirm thatprogramming mode has ...

SECURILOCK Y PASSIVE ANTI-THEFT SYSTEM (IF EQUIPPED) SecuriLock y passive anti-theft system is an engine immobilization system. This system prevents the engine from being started unless a coded key programmed to your vehicle is used. The SecuriLock y passive anti-theft system is not compatible with ...

Programming spare keys A maximum of eight keys can be coded to your vehicle. OnlySecuriLock y keys can be used. To program a coded key yourself, you will need two previously programmed coded keys (keys that already operate your vehicle’s engine) and the new unprogrammed key(s) readilyaccessible for ...

SEATING Adjusting the front manual seat Never adjust the driver’s seat or seatback when the vehicle ismoving. Do not pile cargo higher than the seatbacks to reduce the risk ofinjuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lapbelt snug and low ...

Pull lever up to adjust seatback. Using the manual lumbar support (if equipped) Turn the lumbar support controlclockwise to increase firmness. Turn the lumbar support controlcounterclockwise to increasesoftness. REAR SEATS Center facing jump seat (2 door SuperCab) (if equipped) To open, pull inboard...

Center facing jump seat (4 door SuperCab) (if equipped) To open, pull seat assembly down,then raise seatback. To stow the seat, fold seat backdown and raise seat assembly to thefully upright position. Do not install a child seat ina center facing jump seat. SAFETY RESTRAINTS Safety restraints precau...

In a rollover crash, an unbelted person is significantly more likelyto die than a person wearing a safety belt. Each seating position in your vehicle has a specific safety beltassembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on t...

The front outboard safety restraints in the vehicle are combination lapand shoulder belts. The front passenger outboard safety belt has twotypes of locking modes described below: Energy Management Feature • This vehicle has a seat belt system with an energy managementfeature at the front outboard se...

After any vehicle collision, the seat belt system at all outboardseating positions (except driver, which has no “automatic locking retractor” feature) must be checked by a qualified technician to verifythat the “automatic locking retractor” feature for child seats is stillfunctioning properly. In ad...

• Regular Cab and 4–door SuperCab • 2–door SuperCab To lower the shoulder belt height, push the button and slide the heightadjuster down. To raise the height of the shoulder belt, slide the heightadjuster up. Pull down on the height adjuster to make sure it is locked inplace. Position the shoulder b...

Lap belts Adjusting the front center seat lap belt (if equipped) The lap belt does not adjust automatically. The lap belt should fit snugly and as low as possible around thehips, not across the waist. Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfr...

If you need to lengthen the belt, unfasten it and repeat the procedureabove. To unfasten the belt, push in the release button prior to opening the reardoor. Safety belt extension assembly If the safety belt is too short when fully extended, there is a 20 cm(8 inch) safety belt extension assembly tha...

BeltMinder The BeltMinder feature is a supplemental warning to the safety beltwarning function. This feature provides additional reminders to thedriver that the driver’s safety belt is unbuckled by intermittentlysounding a chime and illuminating the safety belt warning lamp in theinstrument cluster....

Reasons given... Consider... “Crashes are rare events” 36 700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be seriously injured in a crash duringour lifetime. “I’m not going far” 3 of 4 fatal crashes occur within 25 mile...

Reasons given... Consider... “I have an air bag” Air bags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety ...

To reduce the risk of injury, do not deactivate/activate the BeltMinder feature while driving the vehicle. 1. Turn the ignition switch to the RUN (or ON) position. (DO NOTSTART THE ENGINE.) 2. Wait until the safety belt warning light turns off. (Approximately 1–2minutes.) • Steps 3–5 must be complet...

there are no nicks, tears or cuts. Replace if necessary. All safety beltassemblies, including retractors, buckles, front seat belt buckleassemblies, buckle support assemblies (slide bar-if equipped), shoulderbelt height adjusters (if equipped), shoulder belt guide on seatback (ifequipped), child saf...

Important supplemental restraint system (SRS) precautions The supplemental restraint systemis designed to work with the safetybelt to help protect the driver andright front passenger from certainupper body injuries. Air bags DO NOT inflate slowly orgently and the risk of injury from adeploying air b...

Do not put anything on or over the air bag module. Placingobjects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causingserious injury. Do not attempt to service, repair, or modify the Air BagSupplemental Restraint System or its ...

How does the air bag supplemental restraint system work? The air bag SRS is designed toactivate when the vehicle sustainssufficient longitudinal deceleration. The fact that the air bags did notinflate in a collision does not meanthat something is wrong with thesystem. Rather, it means the forceswere...

Several air bag system components get hot after inflation. Do nottouch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in acollision. The SRS ...

If any of these things happen, even intermittently, have the SRS serviced atyour dealership or by a qualified technician immediately. Unless serviced, thesystem may not function properly in the event of a collision. Disposal of air bags and air bag equipped vehicles(including pretensioners) For disp...

If the light fails to illuminate when the passenger air bag switchis in the OFF position and the ignition switch is in ON, have the passenger air bag switch serviced at your Ford or Lincoln-Mercurydealer immediately. In order to avoid inadvertent activation of the switch, alwaysremove the ignition k...

NHTSA deactivation criteria (excluding Canada) 1. Infant. An infant (less than 1 year old) must ride in the front seat because: • the vehicle has no rear seat; • the vehicle has a rear seat too small to accommodate a rear-facinginfant seat; or • the infant has a medical condition which, according to...

Transport Canada deactivation criteria (Canada Only) 1. Infant: An infant (less than 1 year old) must ride in the front seat because: • the vehicle has no rear seat; • the rear seat in the vehicle cannot accommodate a rear-facing infantseat; or • the infant has a medical condition which, according t...

SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly use safetyrestraints for children. Also see Air bag supplemental restraint system (SRS) in this chapter for special instructions about using air bags. Important child restraint precautions You are required by...

7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with knee on thechild seat. 8. Allow the safety belt to retract toremove any slack in the belt. 9. Before placing the child in theseat, forcibly tilt the seat forwardand back to make...

The tether strap anchors in your vehicle are in the following positions(shown from top view): • Bucket seats • 60/40 seats Attach the tether strap only to the appropriate tether anchor asshown. The tether strap may not work properly if attached somewhere other than the correct tether anchor. Seating...

Center seating location When installing a child safety seat in the center position, route the tetherstrap over the center arm rest and clip it to the center anchor. Seating and Safety Restraints 142

Center seating location 60/40 vinyl seats When installing a child safety seat in the center position on a 60/40 vinylseat, route the tether strap through the guiding sleeve and clip it to thecenter anchor. If the tether strap is clipped incorrectly, the child safety seatmay not be retained properly ...

STARTING Positions of the ignition 1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 2. LOCK, locks the steering wheel,automatic transmission gearshiftlever and allows key removal. 3. OFF, shuts off the engine and allaccessories without lockin...

Do not start your vehicle in a closed garage or in other enclosedareas. Exhaust fumes can be toxic. Always open the garage door before you start the engine. See Guarding against exhaust fumes in this chapter for more instructions. If you smell exhaust fumes inside your vehicle, have your dealerinspe...

Starting the engine Note: Whenever you start your vehicle, release the key as soon as the engine starts. Excessive cranking could damage the starter. 1. Turn the key to 5 (START)without pressing the acceleratorpedal and release as soon as theengine starts. The key will return to4 (ON). 2. If the tem...

aggravated by environmental conditions such as cold, heat, moisture,road dust, salt or mud. If a “metal-to-metal,” “continuous grinding” or“continuous squeal” sound is present while braking, the brake liningsmay be worn-out and should be inspected by a qualified servicetechnician. Four-wheel anti-lo...

ABS warning lamp ABS The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does notilluminate momentarily at start up, remains on or continues to flash, theABS needs to be serviced. With the ABS light on, the anti-lockbrak...

Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy. STEERING Your vehicle is equipped with power steering. Power steering uses energyfrom the engine to help steer the vehicle. To prevent damage to the power ste...

To avoid injury, never run the engine with one wheel off theground, such as when changing a tire. PREPARING TO DRIVE YOUR VEHICLE Utility vehicles have a significantly higher rollover rate thanother types of vehicles. In a rollover crash, an unbelted person is significantly more likelyto die than a ...

AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever from being moved from P (Park) when the ignition isin the ON position unless the brake pedal is depressed. If you cannot move the gearsh...

Driving with a 5–speed automatic transmission (if equipped) Your automatic transmission electronically controls the shift feel by usingan adaptive learning strategy. This feature is designed to increasedurability, and provide consistent shift feel over the life of the vehicle. Itis normal for a new ...

R (Reverse) With the gearshift lever in R(Reverse), the vehicle will movebackward. Always come to acomplete stop before shifting intoand out of R (Reverse). N (Neutral) With the gearshift lever in N(Neutral), the vehicle can be startedand is free to roll. Hold the brakepedal down while in this posit...

To return to (Overdrive) mode, press the transmission control switch. The TCIL will no longer be illuminated. Each time the vehicle is started, the transmission will automaticallyreturn to normal (Overdrive) mode. 2 (Second) Use 2 (Second) to start-up onslippery roads or to provideadditional engine ...

MANUAL TRANSMISSION OPERATION (IF EQUIPPED) USING THE CLUTCH Vehicles equipped with a manualtransmission have a starter interlockthat prevents starting the engineunless the clutch pedal is fullydepressed. When starting a vehicle with amanual transmission: 1. Hold down the brake pedal. 2. Depress the...

PARKING 1. Apply the brake and shift into N(Neutral). 2. Engage the parking brake. 3. Shift into 1 (First). 4. Turn the ignition to Off. Do not park your vehicle in Neutral, it may move unexpectedlyand injure someone. Use 1 (First) gear and set the parking brake fully. Driving 158

Using a manual 4WD system (if equipped) 2H (2WD High) – Power to rear axle only. 4H (4WD High) – Power to front and rear axles. N (Neutral) – No power to either axle. 4L (4WD Low) – Power to front and rear axles at reduced speed. Shifting from 2H (2WD high) to 4H (4WD high) Move the transfer case le...

4. Move the transfer case shift leverthrough N (Neutral) directly to 4L(4WD Low) and hold the shift leverin 4L (4WD Low) until the transfercase has fully engaged (up to 15seconds). 5. If the transfer case does not engage into 4L (4WD Low), repeatsteps 1 through 4. Shifting from 4L (4WD low) to 4H (4...

FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) For important information regarding safe operation of this typeof vehicle, see Preparing to drive your vehicle in this chapter. When four–wheel drive (4WD) is engaged, power is supplied to all fourwheels through a transfer case. 4WD power can be selecte...

Shifting from 2WD (2WD high) to 4X4 HIGH (4WD high) Move the 4WD control to the 4X4HIGH position. • At temperatures below 0°C(32°F), shifts from 2WD to 4X4HIGH should not be performedabove 72 km/h (45 mph). Do not shift into 4X4 HIGH withthe rear wheels slipping. Shifting from 4X4 HIGH (4WD high) to...

Shifting from 4X4 LOW (4WD low) to 2WD (2WD high) 1. Bring the vehicle to a stop. 2. Depress the brake. 3. Place the gearshift in N (Neutral) (automatic transmission) or depressthe clutch (manual transmission). 4. Move the 4WD control to the2WD position. Shifting between 4X4 HIGH (4WD high) and 4X4 ...

4WD Systems (if equipped) 4WD (when you select the 4WD mode), uses all four wheels to poweritself. This increases traction, enabling you to drive over terrain and roadconditions that a conventional two-wheel drive vehicle can’t. Power is supplied to all four wheelsthrough a transfer case. On 4WDvehi...

Mud and water If you must drive through highwater, drive slowly. Traction orbrake capability may be limited. When driving through water,determine the depth; avoid waterhigher than the bottom of the hubs(if possible) and proceed slowly. Ifthe ignition system gets wet, thevehicle may stall. Once throu...

“Tread Lightly” is an educationalprogram designed to increase publicawareness of land-use regulationsand responsibilities in our nationswilderness areas. Ford joins the U.S.Forest Service and the Bureau of Land Management in encouraging youto help preserve our national forest and other public and pr...

Descend a hill in the same gear youwould use to climb up the hill toavoid excessive brake applicationand brake overheating. Do notdescend in neutral, disengageoverdrive or manually shift to alower gear. When descending asteep hill, avoid sudden hardbraking as you could lose control.When you brake ha...

Never drive with chains on the front tires of 4WD vehicles without alsoputting them on the rear tires. This could cause the rear to slide andswing around during braking. Tires, Replacement Requirements 4WD vehicles are equipped with tires designed to provide for safe rideand handling capability. Do ...

Each day before you drive, checkyour tires. If one looks lower thanthe others, use a tire gauge to checkpressure of all tires, and adjust ifrequired. Check tire pressure with atire gauge every few weeks(including spare). Safe operationrequires tires that are neitherunderinflated nor overloaded. Peri...

• Maximum Trailer Weight Rating: Maximum weight of a trailer the vehicle is permitted to tow. The maximum trailer weight rating isdetermined by subtracting the vehicle curb weight for eachengine/transmission combination, any required option weight for trailertowing and the weight of the driver from ...

Special loading instructions for owners of pickup trucks andutility-type vehicles For important information regarding safe operation of this typeof vehicle, see the Preparing to drive your vehicle section in this chapter. Loaded vehicles, with a higher center of gravity, may handledifferently than u...

Preparing to tow Use the proper equipment for towing a trailer, and make sure it isproperly attached to your vehicle. See your dealer or a reliable trailerdealer if you require assistance. Hitches For towing trailers up to 907 kg (2 000 lb), use a weight carrying hitchand ball which uniformly distri...

Refer to the following chart for information regarding thefactory-equipped trailer tow connector: Trailer tow connector Color Function Comment 1. Dark Green Trailer right-handturn signal Circuit activated when brakepedal is depressed or whenignition is on and right-handturn signal is applied. 2. Yel...

Trailer towing tips • Practice turning, stopping and backing up before starting on a trip toget the feel of the vehicle trailer combination. When turning, makewider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached. • The tra...

4X2 AND 4X4 VEHICLES EQUIPPED WITH MANUALTRANSMISSIONS Before you have your vehicle towed: • Release the parking brake. • Move the gearshift to N (Neutral). • Turn the key in the ignition to the OFF/UNLOCKED position. • The maximum recommended speed is 88 km/h (55 mph). • The maximum recommended dis...

GETTING ROADSIDE ASSISTANCE To fully assist if you should have a vehicle concern, Ford Motor Companyoffers a complimentary roadside assistance program. This program isseparate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for the Basic warranty peri...

FUSES AND RELAYS Fuses If electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check the appropriatefuses before replacing any electricalcomponents. Note: Always replace a fuse with one that has the specified amperage r...

Passenger compartment fuse panel The fuse panel is located on theleft-hand side of the instrumentpanel facing the driver’s side door.Pull the panel cover outward toaccess the fuses. To remove a fuse use the fuse puller tool provided on the fuse panelcover. 1 234 5 678 9 1 01 11 2 13 14 15 16 17 18 1...

Power distribution box The power distribution box islocated in the engine compartment.The power distribution box containshigh-current fuses that protect yourvehicle’s main electrical systemsfrom overloads. Always disconnect the battery before servicing high currentfuses. To reduce risk of electrical...

If you use the temporary spare tire continuously or do not followthese precautions, the tire could fail, causing you to lose control of the vehicle, possibly injuring yourself or others. When driving with the temporary spare tire do not: • exceed 80 km/h (50 mph) under any circumstances • load the v...

Removing the spare tire 1. Assemble the jack handle to the lug wrench as shown in theillustrations. When connecting the jack handle, assemble the following: • one handle extension and onetypical extension. To assemble,slide parts together. Todisconnect, depress button andpull apart. • one wheel nut ...

3. Insert the straight end of the jackhandle into the rear access holelocated just above the rear bumperand below the tailgate. Forward motion will stop andresistance to turning will be feltwhen properly engaged. 4. Turn the handle counterclockwiseuntil tire is lowered to the groundand the cable is ...

Tire change procedure To prevent the vehicle from moving when you change a tire, besure the parking brake is set, then block (in both directions) the wheel that is diagonally opposite (other side and end of the vehicle) tothe tire being changed. If the vehicle slips off the jack, you or someone else...

8. Replace the flat tire with the spare tire, making sure the valve stem isfacing outward. Reinstall the lug nuts until the wheel is snug against thehub. Do not fully tighten the lug nuts until the wheel has been lowered. 9. Lower the wheel by turning the jack handle counterclockwise. 10. Remove the...

3. Park the booster vehicle close to the hood of the disabled vehiclemaking sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other movingparts. 4. Check all battery terminals and remove any excessive corrosion beforeyou attach th...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingbelt. Ford Motor Company has notapproved a ...

GETTING THE SERVICES YOU NEED At home Ford Motor Company and Ford of Canada have authorized dealerships toservice your vehicle. It is preferred that you return to the Ford dealerwhere your vehicle was purchased when warranty repairs are needed.However, you may also take your vehicle to another Ford ...

In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action un...

THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes • available free to owners and lessees of qualifying Ford Motor Companyvehicles The Dispute Settlement Board may not be available in all states. FordMotor...

Board membership The Board consists of: • three consumer representatives • a Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained byan independent consulting firm. The dealership Board member is chosenfrom Ford and Lincoln Mercury deale...

You will receive a letter of explanation if your application does notqualify for Board review. Oral presentations If you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral presentationbefore the Board, this is not a requireme...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) In those cases where you continue to feel that the efforts by Ford andthe dealer to resolve a factory-related vehicle service concern have beenunsatisfactory, Ford of Canada participates in an impartial third partymediation/arbitration program...

If your vehicle must be serviced while you are traveling or living inCentral or South America, the Caribbean, or the Middle East, contact thenearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANYWORLDWIDE DIRECT MARKET OPERATIONS1555 Fairlane DriveFairlane Busi...

WASHING THE EXTERIOR OF YOUR VEHICLE Never wash a vehicle that is “hot tothe touch” or during exposure tostrong, direct sunlight. It isrecommended that you wash yourvehicle regularly with cool orlukewarm water and a neutral Phshampoo, such as Detail Wash(ZC-3–A), which is available fromyour authoriz...

Cleaning the engine Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • The engine must be cool to the touch before spraying with water. • Never spray a hot engine with cold water, as damage to theengine block or engine co...

WASHING NON-PAINTED PLASTIC EXTERIOR PARTS Use Detail Wash (ZC-3–A) for routine cleaning. If tar or grease spots are present, clean with Extra Strength Tar andRoad Oil Removal (B7A-19520–AA). Use only approved products to clean plastic parts. These products are available from your authorized Ford, L...

FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Your Ford, Lincoln or Mercury dealer has many quality products availableto clean your vehicle and protect its finishes. These quality productshave been specifically engineered to fulfill your automotive needs; theyare custom designed to complement the styl...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a scheduled maintenance guide which makes trackingroutine service easy. If your vehicle requires professional service, your dealership can providethe...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Windshield washer fluid reservoir 2. Engine coolant reservoir 3. Engine oil dipstick 4. Transmission fluid dipstick (automatic transmission) 5. Engine oil filler cap 6. Brake fluid reservoir 7. Power distribution box 8. Clutch fluid ...

WINDSHIELD WASHER FLUID Washer fluid Check the washer fluid wheneveryou stop for fuel. The reservoir ishighlighted with a symbol. If the level is low, add enough fluidto fill the reservoir. In very coldweather, do not fill the reservoir allthe way. Only use a washer fluid that meets Ford specificati...

ENGINE OIL Checking the engine oil Refer to the scheduled maintenance guide for the appropriate intervalsfor checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into theoil pan. 3. Set the parking brake and ensure t...

6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is between the MIN and MAX marks, the oil level is acceptable, DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough oil to raise the levelwithin the MIN-MAX range. • 2.3L I4 engine • 3.0L...

• 4.0L SOHC V6 engine • Oil levels above the MAX mark may cause engine damage. Some oilmust be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in...

Engine Oil Recommendations 2.3L & 3.0L Engines Look for this certificationtrademark. SAE 5W-20 engine oil is recommended. Change your engine oil and filter according to the appropriate schedulelisted in the scheduled maintenance guide. Do not use supplemental engine oil additives, oil treatments...

If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trouble-free operation, keep the top of the battery clean anddry. Also, make certain the battery cables are always tightly fastened tothe battery terminals. If you see any corro...

2. Put the gearshift in P (Park), turn off all accessories and start theengine. 3. Run the engine until it reaches normal operating temperature. 4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine to idle for at least one minute. 6. Drive the vehicle to compl...

testing is possible with a hydrometer or antifreeze tester (such as theRotunda Battery and Antifreeze Tester, 014–R1060). The level of coolantshould be maintained at the “cold full” of “cold fill range” level in thecoolant reservoir. If the level falls below, add coolant per the instructionsin the A...

When the engine is cold, check the level of the engine coolant in thereservoir. • The engine coolant should be at the “cold fill level” or within the “coldfill range” as listed on the engine coolant reservoir (depending uponapplication). • Refer to the Scheduled Maintenance Guide for service interva...

• Add Motorcraft Premium Engine Coolant (green-colored),VC-4–A (U.S.) or CXC-10 (Canada) or Motorcraft PremiumGold Engine Coolant (yellow-colored), VC-7–A, depending onthe type of coolant originally equipped in your vehicle. If you are unsure which type of coolant your vehicle requires, check yourco...

To avoid personal injury, make sure the engine is cool beforeunscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come out forcefully when thecap is loosened slightly. 1. Before you begin, turn the engine off and let it cool. 2. When the engine i...

Recycled engine coolant Ford Motor Company recommends the use of a recycled engine coolantproduced by Ford-approved processes in vehicles originally equippedwith Motorcraft Premium Engine Coolant (green-colored). However, notall coolant recycling processes produce coolant that meets Fordspecificatio...

• NEVER decrease the coolant concentration below 40%. • Decreased engine coolant concentrations below 40% willdecrease the corrosion protection characteristics of the enginecoolant and may cause engine damage. • Decreased engine coolant concentrations below 40% willdecrease the freeze protection cha...

Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materialsand any open flames beforefueling your vehicle. • Always turn off the vehicle beforefueling. • Automotive fuels can be harmfulor fatal if swallowed. Fuel such asgasoline is highly toxic and ifswallowed ...

The flow of fuel through a fuel pump nozzle can produce staticelectricity, which can cause a fire if fuel is pumped into an ungrounded fuel container. Use the following guidelines to avoid static build-up when filling anungrounded fuel container: • Place approved fuel container on the ground. • DO N...

It should not be necessary to add any aftermarket products to your fueltank if you continue to use high quality fuel of the recommended octanerating. Aftermarket products could cause damage to the fuel system.Repairs to correct the effects of using an aftermarket product in yourfuel may not be cover...

Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in kilometers or miles). 2. Each time you fill the tank, record the amount of fuel added (in litersor gallons). 3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current od...

• Using the air conditioner or defroster may reduce fuel economy. • You may want to turn off the speed control in hilly terrain ifunnecessary shifting between third and fourth gear occurs.Unnecessary shifting of this type could result in reduced fueleconomy. • Warming up a vehicle on cold mornings i...

• Four-wheel-drive operation (if equipped) is less fuel efficient thantwo-wheel-drive operation. • Close windows for high speed driving. EPA window sticker Every new vehicle should have the EPA window sticker. Contact yourdealer if the window sticker is not supplied with your vehicle. The EPAwindow ...

CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid.Refer to the scheduled maintenanceguide for the service intervalschedules. If adding fluid isnecessary, use only MERCON t ATF. 1. Start the engine and let it run until it reaches normal operatingtemperature (the engine coolant t...

BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked andrefilled as needed. Refer to thescheduled maintenance guide forthe service interval schedules. 1. Clean the reservoir cap beforeremoval to prevent dirt or waterfrom entering the reservoir. 2. Visually inspect the fluid leve...

CLUTCH FLUID (IF EQUIPPED) Check the fluid level. Refer to the scheduled maintenance guide for theservice interval schedules. During normal operation, the fluid level in the clutch reservoir shouldremain constant. If the fluid level drops, refill the fluid level to the stepin the reservoir. Use only...

Automatic transmission fluid expands when warmed. To obtain anaccurate fluid check, drive the vehicle until it is at normal operatingtemperature (approximately 30 km [20 miles]). If your vehicle has beenoperated for an extended period at high speeds, in city traffic during hotweather or pulling a tr...

The transmission fluid should be inthis range if at normal operatingtemperature (66°C-77°C[150°F-170°F]). The transmission fluid should be inthis range if at ambient temperature(10°C-35°C [50°F-95°F]). High fluid level Fluid levels above the safe rangemay result in transmission failure.An overfill c...

Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug.2. Remove the filler plug andinspect the fluid level. 3. Fluid level should be at bottom of the opening. 4. Add enough fluid through thefiller opening so that the fluid levelis at the bottom of the opening. 5. Insta...

Checking and adding transfer case fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug andinspect the fluid level. 3. Add only enough fluid throughthe filler opening so that the fluidlevel is at the bottom of theopening. Use only fluid that meets Ford specifications. Refer to Lubr...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B, and C, representing thetire’s resistance to the gen...

Tire rotation Because your vehicle’s tires perform different jobs, they often weardifferently. To make sure your tires wear evenly and last longer, rotatethem as indicated in the scheduled maintenance guide. If you notice thatthe tires wear unevenly, have them checked. The following procedure applie...

Replacing the tires Replace the tires when the wearband is visible through the tiretreads. When replacing full size tires, never mix radial bias-belted, orbias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same size, speedrating, and...

* Refer to Vehicle Emissions Control Information (VECI) decal for sparkplug gap information. ** Two spark plugs per cylinder required (eight total). *** If any spark plug needs to be removed for inspection, it must bere-installed in the same cylinder. Cylinders No.1, 2 and 3 have a “PG”suffix. Cylin...

Fluid Ford PartName Application Capacity Transmissionfluid 1 MotorcraftMERCON t ATF 5-speed manual 2.65L(2.8 quarts) 3 MotorcraftMERCON t V ATF 4x2 vehicleswith automaticand 2.3L I4engine 9.4L(9.9 quarts) 2 4x2 vehicleswith automaticand 3.0L or 4.0Lengines 9.5L(10.0 quarts) 2 4x4 vehicleswith automa...

4 Add the coolant type originally equipped in your vehicle. 5 Traction-Lok axles use 2.2–2.4L (4.75–5.0 pints) of rear axle lubricant. Add 118 ml (4 oz.) of Additive Friction Modifier C8AZ-19B546-A orequivalent meeting Ford specification EST-M2C118–A for complete refillof Traction-Lok axles. Service...

Item Ford partname orequivalent Ford partnumber Fordspecification Engine oil 2.3L and 3.0Lengines Motorcraft SAE5W-20 SuperPremium MotorOil XO-5W20-QSP WSS-M2C153-Hand APICertificationMark 4.0L engines Motorcraft SAE5W-30 SuperPremium MotorOil XO-5W30-QSP WSS-M2C205–Aand APICertificationMark Hinges,...

VEHICLE DIMENSIONS Vehicledimensions Regular CabShort WheelBase (SWB) mm(in) Regular CabLong WheelBase (LWB)mm (in) Supercab mm(in) (1) Overalllength 4 763 (187.5) 5 093 (200.5) 5 153 (202.9) (2) Overallwidth 1 785 (70.3) 1 785 (70.3) 1 785 (70.3) (3) Overallheight 4x2/4x4 1 593.5 (62.7) /1 655 (65....

FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of genuine Ford accessories are available for yourvehicle through your local authorized Ford, Lincoln Mercury or Ford ofCanada dealer. These quality accessories have been specificallyengineered to fulfill your automotive needs; they are custom desig...

A Air bag supplemental restraintsystem ................................123–124 and child safety seats ............125description ..............................124disposal ....................................128driver air bag ..........................126indicator light ...................12, 127oper...