Ford 2002 Explorer Sport Trac v.1- Manuals

WARNING LIGHTS AND CHIMES Check engine Your vehicle is equipped with acomputer that monitors the engine’semission control system. Thissystem is commonly known as theOn Board Diagnostics System (OBDII). This OBD II system protects the environment by ensuring that yourvehicle continues to meet governm...

3. The fuel cap may not have been properly installed and securelytightened. These temporary malfunctions can be corrected by filling the fuel tankwith high quality fuel of the recommended octane and/or properlyinstalling and securely tightening the gas cap. After three driving cycleswithout these or...

Air bag readiness Momentarily illuminates when theignition is turned ON. If the lightfails to illuminate, continues to flashor remains on, have the systemserviced immediately. Safety belt Momentarily illuminates when theignition is turned to the ON positionto remind you to fasten your safetybelts. F...

Turn signals Illuminates when the left or rightturn signal or the hazard lights areturned on. If one or both of theindicators stay on continuously orflash faster, check for a burned-outturn signal bulb. Refer to Bulbs in the Maintenance and care chapter. High beams Illuminates when the high beamhead...

Four wheel drive low (if equipped) Momentarily illuminates after theengine is STARTED. Illuminateswhen four-wheel drive low isengaged. If the light continues toflash have the system serviced. Four wheel drive high (if equipped) Momentarily illuminates after thevehicle has been STARTED.Illuminates wh...

Speed control This light comes on when either theSET/ACCEL or RESUME controlsare pressed. It turns off when thespeed control OFF control ispressed, the brake or clutch (if equipped) is applied or the ignition isturned to the OFF position. Safety belt warning chime Sounds to remind you to fasten your...

GAUGES Speedometer Indicates the current vehicle speed. Engine coolant temperature gauge Indicates the temperature of theengine coolant. At normal operatingtemperature, the needle remainswithin the normal area (the areabetween the “H” and “C”). If itenters the red section, the engine isoverheating. ...

Never remove the coolant reservoir cap while the engine isrunning or hot. Steam and scalding liquid from a hot cooling system can burn you badly. This gauge indicates the temperature of the engine coolant, not thecoolant level. If the coolant is not at its proper level the gauge indicationwill not b...

Battery voltage gauge This shows the battery voltage whenthe ignition is in the ON position. Ifthe pointer moves and stays outsidethe normal operating range (asindicated by arrows), have thevehicle’s electrical system checkedas soon as possible. Engine oil pressure gauge This shows the engine oil pr...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parkinglamps. Rotate to the second positionto turn on the headlamps. Foglamp control (if equipped) The foglamps can be turned onwhen the headlamp control is ineither of the following positions: • Parking lamps • Low bea...

High beams • Push forward past detent toactivate. • Pull toward you past detent todeactivate. Flash to pass Pull toward you slightly to activateand release to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of theinstrument panel during headlampand parklamp operation. • Rotate up to br...

CLIMATE CONTROL SYSTEM Manual heating and air conditioning system (if equipped) Fan speed control Controls the volume of air circulatedin the vehicle. Temperature control knob Controls the temperature of theairflow inside the vehicle. Mode selector control Controls the direction of the airflowto the...

• A/C-Uses outside air to cool the vehicle. It is quieter than MAX A/Cbut not as economical. Airflow will be from the instrument panelregisters. • (Panel)-Distributes outside air through the instrument panel registers. However, the air will not be cooled below the outsidetemperature because the air ...

• To reduce humidity buildup inside the vehicle in cold weatherconditions, don’t drive with the climate control system in the OFF orMAX A/C position. • To reduce humidity buildup inside the vehicle in warm weatherconditions, don’t drive with the climate control system in the OFFposition. • Under nor...

1. Select 2. Set the temperature control to full heat 3. Set the fan speed to HI 4. Direct the outer panel vents towards to side windows To increase airflow to the outer panel vents, close the central panelvents. Do not place objects on top of the instrument panel, as theseobjects may become project...

Select for air to flow through these vents: Select for air to flow through these vents: POWER DOWN BACK WINDOW To operate the power down back window, the ignition switch must be inthe Run or Accessory position. The power down back window only has three window position selections: • Fully open • Vent...

All rear seat occupants and/or cargo must be properly restrainedand clear of the back window opening before operating the power down rear window. Turn control counter-clockwise andrelease to lower window all the wayto the full open position. Turn control clockwise and releaseto raise the window all ...

Normal Operation If an “up” command is selected and the ignition is switched to OFF orSTART during window travel, the window will: 1. stop if it is between the vent position and fully closed or 2. continue to move up to the vent position if it is between vent and fullyopen. If a “down” or “vent” com...

4WD CONTROL (IF EQUIPPED) This control operates the 4WD.Refer to the Driving chapter for more information. USING YOUR AUDIO SYSTEM Premium AM/FM Stereo/Cassette/Single CD 4X4 HIGH 2WD 4X4 LOW FM 1AMC BL RF REW FF SCAN BASS TREB SEL BAL TAPE DISC EJ CD FADE AUTO CLK SIDE 1-2 COMP SHUFFLE EJ MUTE VOL ...

Volume/power control Press the control to turn the audiosystem on or off. Audio power can also be turned onby pressing the AM/FM selectcontrol or the TAPE/CD selectcontrol. Turn control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will...

Autoset memory preset Autoset allows you to set strong radio stations without losing youroriginal manually set preset stations. This feature is helpful on tripswhen you travel between cities with different radio stations. Starting autoset memory preset 1. Select a frequency using the AM/FM select co...

Press the FADE control then press: • to shift the sound to the front and • to shift the sound to the rear. Tape/CD select • To begin tape play (with a tapeloaded into the audio system)while in the radio or CD mode,press the TAPE control. Pressagain during rewind or fast forward to stop the rewind or...

Fast forward The fast forward control works intape and CD modes. • In the tape mode, tape directionwill automatically reverse whenthe end of the tape is reached. • In CD mode, pressing the control fast forwards the CD within thecurrent track. Tape direction select Press SIDE 1–2 to play the alternat...

Compression adjust Compression adjust brings soft andloud CD passages together for amore consistent listening level. Press the COMP control to activateand deactivate compression adjust. Shuffle feature The shuffle feature operates in CDmode (if equipped) and plays alltracks on the current disc in ra...

• to decrease minutes and • to increase minutes. If your vehicle has a separate clock,(other than the digital radiodisplay), the CLK control will notfunction in the above manner. The CLK control will allow you toswitch between media display mode(radio station, stereo information,etc.) and clock disp...

AM/FM select The AM/FM select control works inradio and CD modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press thecontrol to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in CD mode Press this control to stop CD play and begin radi...

Radio station memory preset The radio is equipped with six station memory preset controls. Thesecontrols can be used to select up to six preset AM stations and twelveFM stations (six in FM1 and six in FM2). Setting memory preset stations 1. Select the frequency band with the AM/FM select control. Pr...

Speaker fade adjust Speaker sound can be adjustedbetween the front and rearspeakers. Press the FADE control. Use theSEL control to adjust the soundbetween the front and rear speakers. Menu mode The MENU control allows you toaccess many different featureswithin your audio system. There arethree sets ...

RDS ON/OFF— This feature allows your audio system to receive textinformation from RDS-equipped FM radio stations. Refer to Radio Data System feature. FIND type — Allows you to select your desired FM program type andsearch for that selection. SHOW — Allows you to select from NAME (displays the name o...

stations are found after one pass, the scan function is cancelled and NOTFOUND displays. Radio data system (RDS) feature This feature allows your audiosystem to receive text informationfrom RDS-equipped FM radiostations. To activate RDS: • When in FM mode, press the MENU control until RDS OFF displa...

Press the MENU control until FINDprogram type is displayed. Use the SEL control to select theprogram type. With the feature on,use the SEEK or SCAN control tofind the desired program type from the following selections: • Classic • Country • Info • Jazz • Oldies • R & B • Religious • Rock • Soft ...

Adjusting the volume Press the + control to increasevolume. Press the - control to decreasevolume. From the rear seat controls, volume control can be set no higher thanthe current radio setting unless the speakers are turned off. Refer to Turning speakers on and off. Turning the speakers on and off ...

Mode select Push the MODE control to togglebetween AM, FM1, FM2, tape, CD orCD changer (if equipped). Memory preset control Push the MEMORY controlsuccessively to allow rear seatpassengers to scroll through the 6memory presets in AM, FM1 orFM2. Push the MEMORY control in CDchanger mode (if equipped)...

Cleaning compact discs Inspect all discs for contamination before playing. If necessary, cleandiscs only with an approved CD cleaner and wipe from the center out tothe edge. Do not use circular motion. CD and CD changer care • Handle discs by their edges only. Never touch the playing surface. • Do n...

Radio reception factors Three factors can affect radio reception: • Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km(24 miles). This range can be affected by “signal modulation.” Signalmodulation is a process...

To turn speed control off • Press OFF or • Turn off the vehicle ignition. Once speed control is switched off,the previously programmed setspeed will be erased. To set a speed • Press SET ACC. For speedcontrol to operate, the speedcontrol must be ON and thevehicle speed must be greaterthan 48 km/h (3...

To disengage speed control • Depress the brake pedal or • Depress the clutch pedal (ifequipped). Disengaging the speed control willnot erase the previouslyprogrammed set speed or engineRPM. Pressing OFF will erase thepreviously programmed set speed. OFF ON Controls and features 57

TILT STEERING WHEEL (IF EQUIPPED) Pull the tilt steering control towardyou to move the steering wheel upor down. Hold the control whileadjusting the wheel to the desiredposition, then release the control tolock the steering wheel in position. Never adjust the steering wheel when the vehicle is movin...

Push (tap) the end of the stalkbriefly for a single swipe (no wash).Push and hold for three swipes withwash. Push and hold for a longerwash (up to ten seconds). Speed dependent wipers When the windshield wiper control is set on the intermittent settings,speed-sensitive front wipers automatically adj...

OVERHEAD CONSOLE (IF EQUIPPED) The appearance of your vehicle’s overhead console will vary according toyour option package. Storage compartment (if equipped) Press the OPEN control to open thestorage compartment. The door willopen slightly and can be moved tofull open. The storage compartment may be...

Do not let children play with the moon roof. They may seriouslyhurt themselves. Electronic compass/temperature display (if equipped) Outside air temperature The outside temperature display iscontained in the overhead console. The temperature display can beturned off and on by pressing theMODE contro...

Compass zone adjustment 1. Determine which magnetic zoneyou are in by referring to the zonemap. 2. Turn ignition to the ON position. 3. Press and hold the MODE controluntil VAR appears in the display,then release. The display shouldshow the current zone number. 4. Press the MODE control until thedes...

Compass calibration adjustment Perform this adjustment in an openarea free from steel structures andhigh voltage lines: • Press and hold the MODE controluntil CAL appears in the display(approximately eight seconds)and release. • Drive the vehicle slowly (lessthan 5 km/h [3 mph]) in circlesuntil CAL ...

POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of therocker switch to close. • Press the bottom portion of therocker switch to open. One touch down • Press AUTO completely down andrelease quickly. The driver’swindow will open fully. Depressagain t...

Window lock The window lock feature allows onlythe driver to operate the powerwindows. To lock out all the window controlsexcept for the driver’s press the leftside of the control. Press the rightside to restore the window controls. POWER DOOR LOCKS Press control to unlock all doors. Press control t...

Childproof door locks When these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thedoors are unlocked. The childproof locks are located onrear edge of each rear door andmust be set separately for eachdoor. Setting the lock for one door...

2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the center position to disable adjust function. Fold-away mirrors Pull the side mirrors in carefullywhen driving through a narrowspace, like an automatic car wash. CENTER CONSOLE Your vehicle may be equipped with avariety ...

Use only soft cups in the cupholder. Hard objects can injure youin a collision. AUXILIARY POWER POINT The power point is an additional power source for electrical accessories. • With full console. • Without full console. Power outlets are designed for accessory plugs only. Do not hangany type of acc...

An additional auxiliary power point is located in the bed of the truck. Lift the cover to access the auxiliarypower point. POSITIVE RETENTION FLOOR MAT Position the floor mat so that theeyelets are over the pointed end ofthe retention posts and rotateforward to lock in. Make sure thatthe mat does no...

CARGO CAGE (IF EQUIPPED) Your vehicle may be equipped with a cargo cage designed to extend thepickup box for larger loads. To extend the cargo cage: 1. Lower tailgate. 2. Pull the round knobs on each sideof the cargo cage to release it fromthe pickup box. Red markings behind the knobsindicate the un...

To remove the cargo cage: 1. Extend the cargo cage. 2. Pull the round knobs on each sideof the cage to unlock it. Make sure the locking clip screwsare loose before removing the cargocage. 3. Press the locking clips below themiddle bar and lift the cargo cageout of the channels on the “D” pillar. To ...

To remove the tonneau cover: The tonneau cover weighs 29 kg (70 lbs.) and needs to be supportedduring removal since the panels will automatically lock when set downon the pickup box. This is a two person operation. • Unlock and support the front and rear panels. • Fold the rear panel on top of the f...

The remote entry features only operate with the ignition in the LOCKposition. If there is any potential remote keyless entry problem with your vehicle,ensure ALL key fobs (remote entry transmitters) are brought to the dealership, to aid in troubleshooting. Unlocking the doors Press this control to u...

Sounding a panic alarm Press this control to activate thealarm. To deactivate the alarm, press thecontrol again or turn the ignition toON. Panic alarm will only operate withthe ignition in the OFF position. Replacing the battery The transmitter is powered by one coin type three-volt lithium batteryC...

Replacing lost transmitters If a remote transmitter has been lostand you would like to remove itfrom the vehicle’s memory, or youwould like to purchase additionalremote transmitters and have themprogrammed to your vehicle: • Take all your vehicle’s transmitters to your dealer forprogramming, or • Pe...

Illuminated entry The interior lamps illuminate when the remote entry system is used tounlock the door(s) or sound the personal alarm. The system automatically turns off after 25 seconds or when the ignitionis turned to the ON position. The dome lamp control (if equipped) must not be set to the OFF ...

The factory-set code is located: • on the owner’s wallet card in the glove compartment • marked on the computer module • or at your dealer When pressing the controls on the keyless entry keypad, press themiddle of the controls to ensure a good activation. Programming your own personal entry code 1. ...

Anti-scan feature The keyless entry pad is disabled for1 minute after 7 unsuccessfulattempts at entering a valid keycode. The keypad will flash duringthis 1 minute mode. However, the 7/8 and 9/0 controls will still lock thevehicle. Anti-scan will turned off after: • one minute of keypad inactivity •...

• ignition key is in the ON position • you shift into or through R (reverse) • the brake pedal is released The autolock feature repeats when: • any door is opened then closed while the engine is running and • you put the vehicle in motion by releasing the brake pedal Deactivating autolock Before fol...

6. Press the power door UNLOCK control once then press the powerdoor LOCK control once to toggle the Autolock/Relock state. The hornwill chirp twice (one short, one long) if the feature was enabled or chirponce only it the feature was disabled. 7. Turn ignition to OFF. If autolock/relock has been ch...

Key information Your vehicle is supplied with two coded keys. Only a coded key will start your vehicle. Spare coded keyscan be purchased from yourdealership. Your dealership canprogram your key or you can “do ityourself”, refer to Programming spare keys. Large metallic objects, electronicdevices on ...

Adjusting the front manual seat Never adjust the driver’s seat or seatback when the vehicle ismoving. Do not pile cargo higher than the seatbacks to reduce the risk ofinjuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lapbelt snug and low across t...

Do not pile cargo higher than the seatbacks to avoid injuringpeople in a collision or sudden stop. Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. Reclining the seatback can reduce the effectiveness of the seat’ssafety belt in the event of a collision. ...

Folding down rear 60/40 seats 1. Raise the rear seat head restraint. 2. Flip the bottom of the headrestraint up, toward the front seat. 3. While holding the head restraintin “flat” position, lower the headrestraint to the seat back. 4. Flip the seat release controltoward the front seat. Seating and ...

5. Push the seatback toward thefront seat and completely downuntil it locks into place. A carpeted panel will flip down fromthe back panel to complete the loadfloor. Returning the rear 60/40 seats to upright position 1. Push down seatback releasecontrol and pull seatback up andinto upright position ...

SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. To reduce the risk of injury, make sure children sit where theycan be properly restrained. Never let a passenger hold a child on his or her lap while thevehi...

2. To unfasten, push the releasebutton and remove the tongue fromthe buckle. The front and rear outboard safety restraints in the vehicle arecombination lap and shoulder belts. The front passenger and rear seatoutboard safety belts have two types of locking modes described below: Vehicle sensitive m...

After any vehicle collision, the front passenger outboard seat beltsystem must be checked by a qualified technician to verify that the “automatic locking retractor” feature for child seats is stillfunctioning properly. In addition, all seat belts should be checked forproper function. BELT AND RETRAC...

Lap belts Adjusting the lap belt The lap belt should fit snugly and as low as possible around thehips, not across the waist. • 2nd row center seating position The lap belt will adjust automatically. To fasten, grasp the tongue, andwith a continuous motion, pull out enough webbing to buckle the tongu...

If... Then... The driver’s safety belt isbuckled before the ignitionswitch is turned to the ONposition... The safety belt warning light andindicator chime remain off. BeltMinder The BeltMinder feature is a supplemental warning to the safety beltwarning function. This feature provides additional remi...

Reasons given... Consider... “Crashes are rare events” 36 700 crashes occur every day. The more we drive, the more we areexposed to “rare” events, even forgood drivers. 1 in 4 of us will be seriously injured in a crash duringour lifetime. “I’m not going far” 3 of 4 fatal crashes occur within 25 mile...

Reasons given... Consider... “I have an air bag” Air bags offer greater protection whenused with safety belts. Frontal airbagsare not designed to inflate in rear andside crashes or rollovers. “I’d rather be thrown clear” Not a good idea. People who are ejected are 40 times more likelyto DIE. Safety ...

To reduce the risk of injury, do not deactivate/activate the BeltMinder feature while driving the vehicle. 1. Turn the ignition switch to the RUN (or ON) position. (DO NOTSTART THE ENGINE.) 2. Wait until the safety belt warning light turns off. (Approximately 1–2minutes.) • Steps 3–5 must be complet...

assemblies, including retractors, buckles, front seat belt buckleassemblies, buckle support assemblies (slide bar-if equipped), shoulderbelt height adjusters (if equipped), shoulder belt guide on seatback (ifequipped), child safety seat tether bracket assemblies (if equipped),LATCH child seat tether...

The front passenger air bag is not designed to offer protection tooccupants in the center front seating position. Important supplemental restraint system (SRS) precautions The supplemental restraint systemis designed to work with the safetybelt to help protect the driver andright front passenger fro...

• Recline the seat slightly (one or two degrees) from the uprightposition. Do not put anything on or over the air bag module. Placingobjects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causingserious injury. Do not attempt to ...

Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all theway back. How does the air bag supplemental restraint system work? The air bag SRS is designed ...

hearing loss. Because air bags must inflate rapidly and with considerableforce, there is the risk of death or serious injuries such as fractures,facial and eye injuries or internal injuries, particularly to occupants whoare not properly restrained or are otherwise out of position at the timeof air b...

A difficulty with the system is indicated by one or more of the following: • The readiness light will eitherflash or stay lit. • The readiness light will notilluminate immediately afterignition is turned on. • A series of five beeps will be heard. The tone pattern will repeatperiodically until the p...

When possible, always place children under age 12 in the rear seat ofyour vehicle. Accident statistics suggest that children are safer whenproperly restrained in the rear seating positions than in the front seatingposition. Children and safety belts If the child is the proper size, restrain the chil...

SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all of the manufacturer’s instructions with thesafety seat you put in your vehicle. If you do not install and use thesafety seat properly, the ...

Installing child safety seat in the second row center seatingposition with an automatic locking retractor 1. Place the child safety seat in the center seating position. 2. In a continuous motion, pull out enough webbing from the retractor toroute the tongue through the child seat. 3. While holding t...

PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. Thissystem meets all Canadian Interference-Causing Equipment standardrequirements regulating the impulse electrical field strength of radionoise. When starting a fuel-injected engine, avoid pressing the a...

–18 degrees C (0 degrees F). If you experience this condition you mayfind that a different brand of winter grade (E d 85) (if available in your area) improves the performance of your vehicle. Cold starting performance can also be improved with the use of anengine block heater. The engine block heate...

BRAKES Your service brakes are self-adjusting. Refer to the scheduledmaintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate aperformance concern with the vehicle’s brake system. In normaloperation, automotive brake systems may emit occasional or int...

ABS warning lamp ABS The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does notilluminate momentarily at start up, remains on or continues to flash, theABS needs to be serviced. With the ABS light on, the anti-lockbrak...

The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released. Always set the parking brake fully and make sure that thegearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual t...

If the steering wanders or pulls, the condition could be caused by any ofthe following: • underinflated tire(s) on any wheel(s) • uneven vehicle loading • high crown in center of road • high crosswinds • wheels out of alignment • loose or worn suspension components TRACTION-LOK AXLE (IF EQUIPPED) Th...

Vehicles with a higher center of gravity such as utility andfour-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any morethan low-slung sports cars are desig...

Do not drive your vehicle until you verify that the brakelampsare working. If your vehicle gets stuck in mud or snow it may be rocked out byshifting between forward and reverse gears, stopping between shifts, in asteady pattern. Press lightly on the accelerator in each gear. Do not rock the vehicle ...

Understanding gearshift positions Hold the brake pedal down while you move the gearshift leverfrom P (Park) to another position. If you do not hold the brake pedal down, your vehicle may move unexpectedly and injure someone. P (Park) To put your vehicle in gear, start the engine, depress the brake p...

(Overdrive) can be deactivated by pressing the transmission controlswitch on the end of the gearshiftlever. The transmission control indicatorlight (TCIL) will illuminate on theinstrument cluster. Drive – Not shown on the display. Activate by pressing the transmission control switch on the end of th...

1 (First) Use 1 (First) to provide maximumengine braking on steepdowngrades. Upshifts can be madeby shifting to 2 (Second) or to(Overdrive). Selecting 1 (Low) athigher speeds causes the transmission to shift to a lower gear and willshift to 1 (First) after the vehicle decelerates to the proper vehic...

Recommended shift speeds Upshift according to the following charts for best fuel economy: Upshifts when accelerating (recommended for best fueleconomy) 1-2 22 km/h (14 mph) 2-3 40 km/h (25 mph) 3-4 55 km/h (34 mph) 4-5 70 km/h (44 mph) Upshifts when cruising (recommended for best fuel economy) 1-2 1...

2. Engage the parking brake. 3. Shift into 1 (First). 4. Turn the ignition to Off. Do not park your vehicle in Neutral, it may move unexpectedlyand injure someone. Use 1 (First) gear and set the parking brake fully. FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) For important information regarding s...

4WD system indicator lights The 4WD system indicator lights illuminate only under the followingconditions. If these lights illuminate when driving in 2WD, contact yourFord dealer as soon as possible. • 4WD -momentarily illuminates when the vehicle is started.Illuminates when 4H (4WD High)is engaged....

Shifting from 4X4 HIGH (4WD high) to 2WD (2WD high) Move the 4WD control to 2WDposition at any forward speed. • You do not need to operate the vehicle in R (Reverse) todisengage the 4WD system. Shifting from 2WD (2WD high) to 4X4 LOW (4WD low) 1. Bring the vehicle to a stop. 2. Depress the brake. 3....

4. Move the 4WD control to the2WD position. 5. Wait for the 4WD low indicatorlight to turn off. Shifting between 4X4 HIGH (4WD high) and 4X4 LOW (4WD low) 1. Bring the vehicle to a stop. 2. Depress the brake. 3. Place the gearshift in N (Neutral). 4. Move the 4WD control to the 4X4HIGH or 4X4 LOW po...

Power is supplied to all four wheelsthrough a transfer case. On 4WDvehicles, the transfer case allowsyou to select 4WD when necessary.Information on transfer caseoperation and shifting procedurescan be found in the Driving chapter. Information on transfercase maintenance can be found in the Maintena...

Mud and water If you must drive through highwater, drive slowly. Traction orbrake capability may be limited. When driving through water,determine the depth; avoid waterhigher than the bottom of the hubs(if possible) and proceed slowly. Ifthe ignition system gets wet, thevehicle may stall. Once throu...

“Tread Lightly” is an educationalprogram designed to increase publicawareness of land-use regulationsand responsibilities in our nationswilderness areas. Ford joins the U.S.Forest Service and the Bureau of Land Management in encouraging youto help preserve our national forest and other public and pr...

Descend a hill in the same gear youwould use to climb up the hill toavoid excessive brake applicationand brake overheating. Do notdescend in neutral, disengageoverdrive or manually shift to alower gear. When descending asteep hill, avoid sudden hardbraking as you could lose control.When you brake ha...

Brakes section of this chapter for additional information on the operation of the anti-lock brake system. Never drive with chains on the front tires of 4WD vehicles without alsoputting them on the rear tires. This could cause the rear to slide andswing around during braking. Tires, Replacement Requi...

Each day before you drive, checkyour tires. If one looks lower thanthe others, use a tire gauge to checkpressure of all tires, and adjust ifrequired. Check tire pressure with atire gauge every few weeks(including spare). Safe operationrequires tires that are neitherunderinflated nor overloaded. Peri...

Do not exceed the GVWR or the GAWR specified on thecertification label. Do not use replacement tires with lower load carrying capacities than theoriginals because they may lower the vehicle’s GVWR and GAWRlimitations. Replacement tires with a higher limit than the originals donot increase the GVWR a...

4x4 w/manual transmission GCWR (Gross Combined Weight Rating)/Trailer Weights Engine Rear axle ratio Maximum GCWR - kg (lbs.) Trailer Weight Range (0-Maximum) - kg (lbs.) Maximum frontal area of trailer - m 2 (ft 2 ) 4.0L SOHC All 3 175 (7 000) 0-1 143 (0-2 520) 4.64 (50) Notes: For high altitude op...

Safety chains Always connect the trailer’s safety chains to the frame or hook retainersof the vehicle hitch. To connect the trailer’s safety chains, cross thechains under the trailer tongue and allow slack for turning corners. If you use a rental trailer, follow the instructions that the rental agen...

Driving while you tow When towing a trailer: • Ensure that you turn off your speed control. The speed control mayshut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer. • Use a lower gear when towing up or down stee...

• do not allow waves to break higher than 15 cm (6 inches) above thebottom edge of the rear bumper. Exceeding these limits may allow water to enter critical vehiclecomponents, adversely affecting driveability, emissions, reliability andcausing internal transmission damage. Replace the rear axle lubr...

Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the Basic warranty peri...

The fuel pump shut-off switch islocated in the passenger’s foot well,by the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switc...

Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wiredamage and could start a fire. Standard fuse amperage rating and color COLOR Fuse rating Mini fuses Standard fuses Maxi fuses Cartridge maxi fuses Fuse link ca...

Passenger compartment fuse panel The fuse panel is located on theleft-hand side of the instrumentpanel facing the driver’s side door.Pull the panel cover outward toaccess the fuses. To remove a fuse use the fuse puller tool provided on the fuse panelcover. 1 234 5 678 9 1 01 11 2 13 14 15 16 17 18 1...

Power distribution box The power distribution box islocated in the engine compartment.The power distribution box containshigh-current fuses that protect yourvehicle’s main electrical systemsfrom overloads. Always disconnect the battery before servicing high currentfuses. To reduce risk of electrical...

Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the followinglocations: Tool Location Spare tire Under the vehicle, just in front ofthe rear bumper Jack, Jack handle, jack handle extension, wheel lug nut wrench In the passenger side rear cabcompartment be...

2. Insert the jack handle into theopening just above the rear bumper. The handle will stop moving forwardand resistance to turning will be feltwhen properly engaged. 3. Turn the handle counterclockwiseuntil tire is lowered to the ground,and the cable is slack. Slide the tirerearward. 4. Remove the r...

Tire change procedure When one of the front wheels is off the ground, the transmissionalone will not prevent the vehicle from moving or slipping off the jack, even if the vehicle is in P (Park) (automatic transaxle) orR (Reverse) (manual transaxle). To prevent the vehicle from moving when you change...

4. Insert tapered end of the lug nutwrench to remove any wheel trim. 5. Loosen each wheel lug nutone-half turn counterclockwise butdo not remove them until the wheelis raised off the ground. 6. Assemble the jack handleextension on the lug nut wrench bysliding the parts together. Todisconnect, depres...

11. Remove the jack and fullytighten the lug nuts in the ordershown. 12. Stow the flat tire. Refer to Stowing the spare tire. 13. Stow the jack and lug nutwrench. Make sure the jack isfastened so it does not rattle whenyou drive. 14. Unblock the wheels. JUMP STARTING YOUR VEHICLE The gases around th...

4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect any electricalsurges. Turn all other accessories off. Connecting the jumper cables 1. Connect the po...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

• 4.0L SOHC V6 Engine 5. Ensure that the cables are clear of fan blades, belts, moving parts ofboth engines, or any fuel delivery system parts. Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. On...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingbelt. Ford Motor Company has notapproved a ...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a scheduled maintenance guide which makes trackingroutine service easy. If your vehicle requires professional service, your dealership can providethe...

Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thesteering column on the instrumentpanel. 2. Go to the front of the vehicle andrelease the auxiliary latch ...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.0L SOHC V6 engine 1. Windshield washer fluid reservoir 2. Automatic transmission fluid dipstick (if equipped) 3. Engine oil filler cap 4. Engine oil dipstick 5. Brake fluid reservoir 6. Power distribution box 7. Clutch fluid reservoir 8. Battery 9. ...

ENGINE OIL Checking the engine oil Refer to the scheduled maintenance guide for the appropriate intervalsfor checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into theoil pan. 3. Set the parking brake and ensure t...

• If the oil level is below the ADDmark or MIN mark, add enoughoil to raise the level within theADD-FULL range or MIN-MAXrange. • Oil levels above the letter F in FULL or the MAX mark may causeengine damage. Some oil must be removed from the engine by aservice technician. 7. Put the indicator back i...

Engine oil and filter recommendations Look for this certificationtrademark. SAE 5W-30 engine oil recommended Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). Use Motorcraft (Part: XO-5W30–QSP U.S.) oran equivalent oil meeting Ford specification WSS-M2C153–G. D...

BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked andrefilled as needed. Refer to thescheduled maintenance guide forthe service interval schedules. 1. Clean the reservoir cap beforeremoval to prevent dirt or waterfrom entering the reservoir. 2. Visually inspect the fluid leve...

CLUTCH FLUID (IF EQUIPPED) Check the fluid level. Refer to the scheduled maintenance guide for theservice interval schedules. During normal operation, the fluid level in the clutch reservoir shouldremain constant. If the fluid level drops, refill the fluid level to the stepin the reservoir. Use only...

WINDSHIELD WASHER FLUID Washer fluid Check the washer fluid wheneveryou stop for fuel. The reservoir ishighlighted with a symbol. If the level is low, add enough fluidto fill the reservoir. In very coldweather, do not fill the reservoir allthe way. Only use a washer fluid that meets Ford specificati...

ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at themileage intervals listed in the scheduled maintenance guide. The coolantconcentration should be maintained at 50/50 coolant and water, whichequates to a freeze point of -36° C (-34° F). Coola...

• Refer to the Scheduled Maintenance Guide for service intervalschedules. • Be sure to read and understand Precautions when servicing your vehicle in this chapter. If the engine coolant has not been checked at the recommended interval,the engine coolant reservoir may become low or empty. If the rese...

• Do not add/mix an orange-colored, extended life coolant suchas Motorcraft Speciality Orange Engine Coolant, VC-2 (US) orCXC-209 (Canada), meeting Ford specification WSS-M97B44–Dwith the factory-filled coolant. Mixing Motorcraft Speciality Orange Engine Coolant or any orange-colored extended life p...

4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture (seeabove), to within the “cold fill range” or the “cold full” level on thereservoir. If you removed the rad...

Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Refill capacities in the Capacities and specifications chapter. Fill your engine coolant reservoir as outlined in Adding engine coolant in this chapter. Severe climates If you drive in extremely cold c...

operated for an extended period at high speeds, in city traffic during hotweather or pulling a trailer, the vehicle should be turned off for about 30minutes to allow fluid to cool before checking. 1. Drive the vehicle 30 km (20 miles) or until it reaches normal operatingtemperature. 2. Park the vehi...

The transmission fluid should be inthis range if at ambient temperature(10°C-35°C [50°F-95°F]). High fluid level Fluid levels above the safe rangemay result in transmission failure.An overfill condition of transmissionfluid may cause shift and/orengagement concerns and/orpossible damage. High fluid ...

Checking and adding transfer case fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug andinspect the fluid level. 3. Add only enough fluid throughthe filler opening so that the fluidlevel is at the bottom of theopening. Use only fluid that meets Ford specifications. Refer to the ...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. However, for severe usage or in high temperature climates, check thebattery electrolyte level. Refer to the scheduled maintenance guide forthe service ...

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery.Lift the battery with a battery carrier or with your hands on oppositecorners. Keep batteries out of reach of ...

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recycling centerto find out more about recyclingautomotive batteries. WINDSHIELD WIPER BLADES Check the wiper blades at least twice a year or when they seem l...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B, and C, representing thetire’s resistance to the gen...

Tire rotation Because your vehicle’s tires perform different jobs, they often weardifferently. To make sure your tires wear evenly and last longer, rotatethem as indicated in the scheduled maintenance guide. If you notice thatthe tires wear unevenly, have them checked. The following procedure applie...

Replacing the tires Replace the tires when the wearband is visible through the tiretreads. When replacing full size tires, never mix radial bias-belted, orbias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same size, speedrating, and...

USING SNOW TIRES AND TRACTION DEVICES Snow tires must be the same size and grade as the tires youcurrently have on your vehicle. The tires on your vehicle have all-weather treads to provide traction inrain and snow. However, in some climates, using snow tires or tractiondevices may be necessary. For...

If you do not use the proper fuel filler cap, excessive pressure orvacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possiblepersonal injury. Automotive fuels can cause serious injury or death if misused ormishandled. Fuel ethan...

When refueling always shut the engine off and never allowsparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions.Care should be taken to avoid inhaling excess fumes. The flow of fuel through a fuel pump nozzle can produce st...

If you have run out of fuel: • You may need to cycle the ignition from OFF to ON several times afterrefueling, to allow the fuel system to pump the fuel from the tank tothe engine. • Your “Check Engine” indicator may come on. For more information onthe “Check Engine” indicator, refer to the Instrume...

• Allow no more than 2 automatic click-offs when filling. • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same pump and have the vehicle facing thesame direction each time you fill up. • Have the vehicle lo...

• Adding certain accessories to your vehicle (for example bugdeflectors, rollbars/light bars, running boards, ski/luggage racks) mayreduce fuel economy. • Using fuel blended with alcohol may lower fuel economy. • Fuel economy may decrease with lower temperatures during the first12–16 km (8–10 miles)...

Replacing headlamp bulbs To remove the headlamp bulb: 1. Make sure headlamp switch is inOFF position, then lift hood and liftthe plastic headlamp cover. 2. At the back of the headlamp, pryup and remove the two retainer pinsto release the headlamp assemblyfrom the vehicle and pull headlampforward. 3....

1. With the flat side of the new bulb’s plastic base facing upward, insertthe glass end of the bulb into the lamp assembly. Turn the bulb left orright to align the grooves in the plastic base with the tabs in the lampassembly. When the grooves are aligned, push the bulb into the lampassembly until t...

Replacing tail lamp/turn/backup lamp bulbs The tail lamp/turn/backup lamp bulbs are located in the same portion ofthe tail lamp assembly, one just below the other. Follow the same stepsto replace either bulb: 1. Lower the tailgate to expose thelamp assembly. 2. Remove the three rubber plugs,screws a...

To remove the brakelamp assembly: 1. Remove the two screws and lampassembly from vehicle. 2. Remove the bulb socket fromlamp assembly by rotating it 45degrees. 3. Carefully pull bulb straight out ofsocket and push in the new bulb. To install the brakelamp assembly: 1. Install the bulb socket into th...

Vertical aim adjustment 1. Park the vehicle on a level surface approximately 7.6 meters (25 feet)from a vertical wall or screen directly in front of it. This procedureshould be done in a dark enviroment to effectively see the headlampbeam pattern. • (A) Eight feet • (B) Center height of lamp to grou...

Any gasoline spilled on the vehicle or deposits such as bird droppingsshould be washed and sponged off as soon as possible. Deposits notremoved promptly can cause damage to the vehicle’s paintwork. Remove any exterior accessories, such as antennas, before entering a carwash. If you have wax applied ...

Cleaning non-painted plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover ifnecessary. Do not clean plastic parts with thinners, solvents orpetroleum-based cleaners. Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. Ifnecessa...

Cleaning the instrument cluster lens Clean with a damp cloth, then dry with a dry cloth. Do not use household or glass cleaners as these may damage the lens. Cleaning the overhead console Clean with a damp cloth, then wipe dry with a dry cloth. Avoid cleaner or polish that increases the gloss of the...

MOTORCRAFT PART NUMBERS Component 4.0L SOHC V6 engine Air filter element FA-1658 Fuel filter FG-986B Battery BXT-65-650 Oil filter FL-820S PCV valve EV-243 Spark plugs* AGSF-22PP * Refer to Vehicle Emissions Control Information (VECI) decal for sparkplug gap information. REFILL CAPACITIES Fluid Ford...

3 Fill to bottom of filler plug hole. 4 Add the coolant type originally equipped in your vehicle. 5 Fill to 6 mm to 14 mm (1/4 inch to 9/16 inch) below bottom of filler plug hole. 6 For vehicles equipped with a conventional rear axle, refer to your scheduled maintenance guide for axle fluid change i...

Item Ford PartName orequivalent Ford PartNumber FordSpecification Driveshaft, slipspline, universaljoints Premium LongLife Grease XG-1-C orXG-1-T orXG-1-K ESA-M1C75-B Engine coolant MotorcraftPremium EngineCoolant(green-colored) VC-4–A (US) orCXC-10(Canada) ESE-M97B44-A MotorcraftPremium GoldEngine ...

Ford Extended Service Plan You can get more protection for your new car or light truck bypurchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESPis an optional service contract which is backed by Ford Motor Companyor Ford Motor Service Company (in the U.S.) and Ford of Canada (inCanada). ...

taken to another dealer. If a particular dealership can not assist you,then contact the Customer Relationship Center. If you have questions or concerns, or are unsatisfied with the service youare receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at yourselling/se...

THE DISPUTE SETTLEMENT BOARD (U.S. only) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes • available free to owners and lessees of qualifying Ford Motor Companyvehicles The Dispute Settlement Board may not be available in all states. FordMotor...

Board membership The Board consists of: • three consumer representatives • a Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained byan independent consulting firm. The dealership Board member is chosenfrom Ford and Lincoln Mercury deale...

You will receive a letter of explanation if your application does notqualify for Board review. Oral presentations If you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral presentationbefore the Board, this is not a requireme...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) In those cases where you continue to feel that the efforts by Ford andthe dealer to resolve a factory-related vehicle service concern have beenunsatisfactory, Ford of Canada participates in an impartial third partymediation/arbitration program...

nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANYWORLDWIDE DIRECT MARKET OPERATIONS1555 Fairlane DriveFairlane Business Park #3Allen Park, Michigan 48101U.S.A.Telephone: (313) 594-4857FAX: (313) 390-0804 If you are in another foreign country, contact the n...

Protection and appearance equipment Air bag anti-theft locks Automatic headlamp system Bed mats Berber floor mats Carpet floor mats Cleaners, waxes and polishes Door edge guards Front end covers (full and mini) Hood deflectors Locking gas cap Lubricants and oils Molded splash guards Molded vinyl flo...

equipment installed in your vehicle should comply with FCC or CRTCregulations and should be installed only by a qualified servicetechnician. • Mobile communications systems may harm the operation of yourvehicle, particularly if they are not properly designed for automotiveuse or are not properly ins...

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould immediately inform theNational Highway Traffic SafetyAdministration (NHTSA) in additionto notifying Ford Motor Company. If NHTSA receives similar compl...

A ABS (see Brakes) .....................127 Air bag supplemental restraintsystem ................................108–109 and child safety seats ............110description ..............................109disposal ....................................113driver air bag ..........................111indi...

Trunk ...........................................79 Turn signal ............................11, 53 V Vehicle dimensions ...................238 Vehicle Identification Number(VIN) ..........................................240 Vehicle loading ..........................149 Ventilating your vehicle ........

Item Information Required fuel Unleaded fuel only - 87 octane Fuel tank capacity 77.6L (20.5 gallons) Engine oil capacity (includes filterchange) 4.7L (5.0 quarts). Use MotorcraftSAE 5W-30 Super Premium MotorOil, Ford specificationWSS-M2C153-G. Tire size and pressure Refer to the Certification Label...