Ford 2002 Escort v.1- Manuals

This Owner’s Guide describes every option and model variantavailable and therefore some of the items covered may not apply to your particular vehicle. Furthermore, due to printing cycles it maydescribe options before they are generally available. Remember to pass on the Owner’s Guide when reselling ...

Protecting the environment We must all play our part inprotecting the environment. Correctvehicle usage and the authorizeddisposal of waste cleaning andlubrication materials are significantsteps towards this aim. Information in this respect is highlighted in thisguide with the tree symbol. BREAKING-...

Special instructions For your safety, your vehicle is fitted with sophisticated electroniccontrols. By operating other electronic equipment (e.g. mobile telephonewithout exterior aerial) electromagnetic fields can occur which can cause malfunctions of the vehicle electronics. Therefore you shouldobs...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat InstallationWarning Child Seat TetherAnchorage Brake System Anti-Lock Brake System Brake Fluid -Non-Petroleum Based Tr...

WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A warning light mayilluminate when a problem exists with one of your vehicle’s functions.Many lights will illuminate when you start your vehicle to make ...

Service engine soon Illuminates briefly to ensure thesystem is functional. If it comes onafter the engine is started, one ofthe engine’s emission controlsystems may be malfunctioning. Thelight may illuminate without adriveability concern being noted. The vehicle will usually be drivable andwill not ...

Brake system warning Illuminates if the parking brake isengaged. Also momentarilyilluminates at start up to ensure thecircuit is functional. If the brakewarning lamp does not illuminate atthese times, or illuminates after releasing the parking brake, seek serviceimmediately. Refer to Brakes in the D...

Engine oil pressure Illuminates when the oil pressurefalls below the normal range. Checkthe oil level and add oil if needed.Refer to Engine oil in the Maintenance and specifications chapter. Low fuel Illuminates when the fuel level inthe fuel tank is at, or near, empty(refer to Fuel gauge in this ch...

High beams Illuminates when the high beamheadlamps are turned on. Anti-theft system (if equipped) Refer to Anti-theft system in the Locks and Security chapter. Safety belt warning chime Sounds to remind you to fasten your safety belts. BeltMinder chime Sounds intermittently to remind you to fasten y...

Engine coolant temperature gauge Indicates the temperature of theengine coolant. At normal operatingtemperature, the needle remainswithin the normal area (the areabetween the “H” and “C”). If itenters the red section, the engine isoverheating. Stop the vehicle assoon as safely possible, switch offth...

Speedometer Indicates the current vehicle speed. Odometer Registers the total kilometers(miles) of the vehicle. Trip odometer Registers the kilometers (miles) ofindividual journeys. To reset,depress the control. Tachometer (if equipped) Indicates the engine speed inrevolutions per minute. Driving wi...

AM/FM STEREO/CASSETTE Volume/power control Press the control to turn the audiosystem on or off. Turn control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition switch is turne...

Bass/treble adjust • The bass adjust control allowsyou to increase or decrease theaudio system’s bass output. • The treble adjust control allowsyou to increase or decrease theaudio system’s treble output. Speaker balance/fade adjust • Speaker sound distribution can beadjusted between the right andle...

Seek function in tape mode • Press to listen to the previous selection on the tape. • Press to listen to the next selection on the tape. Scan function The scan function works in radio ortape mode. Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stationso...

Radio station memory preset The radio is equipped with six station memory preset controls. Thesecontrols can be used to select up to six preset AM stations and twelveFM stations (six in FM1 and six in FM2). Setting memory preset stations 1. Select the frequency band withthe AM/FM select control. 2. ...

Rewind The rewind control works in tapemode. • In tape mode, radio play willcontinue until rewind is stopped(with the TAPE control) or thebeginning of the tape is reached. Fast forward The fast forward control works intape mode. • In the tape mode, tape directionwill automatically reverse whenthe en...

Volume/power control Press the control to turn the audiosystem on or off. Turn control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition switch is turned back on. If you wish...

Scan function The scan function works in radio,tape or CD mode (if equipped). Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stationson the frequency band. Press the control again to stop the scan mode. Scan function in tape mode Press the SCAN control ...

AM/FM select in CD mode Press this control to stop CD play and begin radio play. You can switch from CD play to tape play by simply inserting a tape intothe cassette deck. Radio station memory preset The radio is equipped with six station memory preset controls. Thesecontrols can be used to select u...

To set the minute, press the minute(m) control and press: • (+) to increase the minute and • (−) to decrease the minute Tune adjust The tune control works in radio orCD mode (if equipped). Tune adjust in radio mode • Press the to move to the next frequency down the band(whether or not a listenablest...

Tune adjust for CD mode (if equipped) • Press the to select the previous disc in the CD changer.(Play will begin on the first trackof the disc unless the CD changeris in shuffle mode. Refer to Shuffle feature for more information. Hold the control tocontinue reversing through thedisc. • Press to sel...

The magazine does not need to befull for the changer to operate. Radio power must be turned on to play the CDs in the changer. Themagazine may be stored in the glove box when not being used. The CD magazine may be inserted or ejected with the radio power off. ONLY use the magazine supplied with the ...

CLEANING COMPACT DISCS Inspect all discs for contamination before playing. If necessary, cleandiscs only with an approved CD cleaner and wipe from the center out tothe edge. Do not use circular motion. CD AND CD CHANGER CARE • Handle discs by their edges only. Never touch the playing surface. • Do n...

HEATER ONLY SYSTEM (IF EQUIPPED) Fan speed control Controls the volume of air circulatedin the vehicle. Temperature control knob Controls the temperature of theairflow inside the vehicle. Onheater-only systems, the air cannotbe cooled below the outsidetemperature. Mode selector control Controls the ...

Temperature control knob Controls the temperature of theairflow inside the vehicle. Mode Selector Control Controls the direction of the airflowto the inside of the vehicle. The air conditioning compressor can operate in all modes exceptand . However, the air conditioning will only function if the ou...

• (Floor) – Distributes outside air through the floor ducts. However, the air will not be cooled below the outside temperaturebecause the air conditioning does not operate in this mode. • (Floor and defrost) – Distributes outside air through the windshield defroster ducts and the floor ducts. Heatin...

windows open. This will force most of the hot, stale air out of thevehicle. Once the vehicle has been “aired out”, operate the climatecontrol system as desired. • Do not put objects under the front seat which may interfere with theairflow to the rear seats (if equipped). • Remove any snow, ice or le...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parkinglamps. Rotate to the second positionto also turn on the headlamps. Foglamp control (if equipped) Rotate forward to activate. Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output....

High beams • Push forward to activate. • Pull toward you to deactivate. Flash to pass Pull toward you to activate andrelease to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlampand parklamp operation. Coupe • Rotate up to brighten. • Rotate down to...

Sedan • Rotate left to brighten • Rotate right to dim The dome lamp will not illuminate if the control switch is in the OFFposition. AIMING THE HEADLAMPS Your vehicle is equipped with a Vehicle Headlamp Aim Device (VHAD)on each headlamp. Each headlamp may be properly aimed in the vertical(up/down) a...

3. The “UP” and “DN” on the bubbleindicate the directional change (upor down) of the vertical aim. 4. Use a 4 mm wrench or socket toturn the vertical adjusting screwclockwise or counterclockwise untilthe bubble is centered between thelines. Repeat the above process to the other headlamp, if necessar...

Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbsmust be marked with an authorized “D.O.T.” for North America and an“E” for Europe to assure lamp performance, light brightness and patternand safe visibility. The correct bulbs will not damage the lamp assemblyor...

Map lamps For bulb replacement, see a qualified service technician or your dealer. Replacing headlamp bulbs 1. Make sure that the headlamps are turned OFF. 2. Open the hood and disconnect the headlamp wiring socket from thein-line connector. This will make it easier to change the bulb. 3. Remove the...

7. Install the new bulb in lamp assembly by pushing straight in with thebulb’s plastic base facing upward. Turn the bulb slightly to align thegrooves in the plastic base with the tabs in the lamp assembly. 8. Install the bulb retaining ring over the plastic base and lock the ringby rotating it clock...

Replacing high-mount brakelamp bulbs To remove the brakelamp bulb: 1. Push the center of the push pinsin to release tension. 2. Pull the push pins out of thecover and slide the cover away fromthe package tray. 3. Remove the bulb by rotating itcounterclockwise and pulling it outof the lamp assembly. ...

4. Remove the bulb socket byrotating it counterclockwise, thenpulling it out of the lamp assembly. 5. Pull the bulb from the socket andpush in the new bulb. 6. Install the bulb socket into thelamp by rotating it clockwise. 7. Position the tail lamp on thevehicle and gently tap the lens toengage the ...

WINDSHIELD WIPER AND WASHER • For intermittent wiping, move thecontrol down one position androtate the wiper switch to thedesired position. • For low speed wiping, move thecontrol down two positions. • For high speed wiping, move thecontrol down three positions. • For mist wiping, move the control u...

Checking the wiper blades If the wiper blades do not wipe properly, clean both the windshield andwiper blades using undiluted windshield wiper solution or a milddetergent. Rinse thoroughly with clean water. To avoid damaging theblades, do not use fuel, kerosene, paint thinner or other solvents. Chan...

Never adjust the steering wheel when the vehicle is moving. POWER WINDOWS (IF EQUIPPED) Press and hold the rocker switches to open and close windows. • Press the top portion of therocker switch to close. • Press the bottom portion of therocker switch to open. Express down To make the driver window o...

POWER SIDE VIEW MIRRORS (IF EQUIPPED) The ignition must be in ACC or ON position to adjust the power sideview mirrors. To adjust your mirrors: 1. Select L to adjust the left mirroror R to adjust the right mirror. 2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the cente...

SPEED CONTROL (IF EQUIPPED) To turn speed control on • Press ON. Vehicle speed cannot be controlleduntil the vehicle is traveling at orabove 48 km/h (30 mph). Do not shift the gearshift leverinto N (Neutral) with the speedcontrol on. Do not use the speedcontrol in heavy traffic or on roads that are ...

If you drive up or down a steep hill, your vehicle speed may varymomentarily slower or faster than the set speed. This is normal. Speed control cannot reduce the vehicle speed if it increases above theset speed on a downhill. If your vehicle speed is faster than the setspeed while driving on a downh...

To set a lower set speed • Press and hold CST. Release thecontrol when the desired speed isreached or • Press and release CST to operatethe Tap-Down function. Eachpress will decrease the set speedby 1.6 km/h (1 mph) or • Depress the brake pedal. Whenthe desired vehicle speed isreached, press SET ACC...

To disengage speed control • Depress the brake pedal or • Depress the clutch pedal (ifequipped). Disengaging the speed control willnot erase the previouslyprogrammed set speed. Pressing OFF will erase thepreviously programmed set speed. ON OFF Driver Controls 60

TRUNK REMOTE CONTROL Press the remote trunk releasecontrol on the instrument panel toopen the trunk. POSITIVE RETENTION FLOOR MAT Position the floor mat so that theeyelet is over the pointed end of theretention post and rotate forward tolock in. Make sure that the mat doesnot interfere with the oper...

KEYS The key operates all locks on yourvehicle. In case of loss, replacementkeys are available from your dealer. You should always carry a secondkey with you in a safe place in caseyou require it in an emergency. Refer to SecuriLock y Passive Anti-Theft System for more information. POWER DOOR LOCKS ...

INTERIOR LUGGAGE COMPARTMENT RELEASE Your vehicle is equipped with a mechanical interior luggage compartmentrelease handle that provides a means of escape for children and adults inthe event they become locked inside the luggage compartment. Adults are advised to familiarize themselves with the oper...

Unlocking the doors Press this control to unlock thedriver’s door. The interior lamps willilluminate. With the all-door remote entrysystem, press the control a secondtime within three seconds to unlockall doors. Locking the doors Press this control to lock all doors.On vehicles equipped with thedriv...

Sounding a panic alarm Press this control to activate thealarm. To deactivate the alarm, press thecontrol again or turn the ignition toACC or ON. Opening the trunk Press the control once to open thetrunk. Ensure that the trunk is closed andlatched before driving your vehicle.Failure to latch the tru...

To replace the battery: 1. Twist a thin coin between the twohalves of the transmitter near thekey ring. DO NOT TAKE THEFRONT PART OF THETRANSMITTER APART. 2. Place the positive (+) side of newbattery in the same orientation.Refer to the diagram inside thetransmitter unit. 3. Snap the two halves back...

Programming remote transmitters It is necessary to have all (maximum of four — original and/or new) of your remote transmitters available prior to beginning this procedure. To program the transmitters yourself: • Insert a key in the ignition andturn from 1 (LOCK) to 2 (ACC)and cycle between 2 (ACC) ...

Arming the anti-theft system Turn the ignition to LOCK, removethe key and press the lock controlon the remote entry transmitter. Identifying an armed system While the system is arming, the THEFT light in the instrument clusterwill illuminate for 30 seconds. After 30 seconds, THEFT will flash,indicat...

A triggered system may also bedisarmed by inserting the key andturning the ignition to ON/ACC orby pressing the panic control. Pressing the trunk control willprevent the alarm from soundinguntil the trunk is closed again. Using the ignition key to unlock doors/trunk will not disarm theanti-theft sys...

SEATING Adjustable head restraints (if equipped) Your vehicle’s seats may be equipped with head restraints which arevertically adjustable. The purpose of these head restraints is to help limithead motion in the event of a rear collision. To properly adjust your headrestraints, lift the head restrain...

Reclining the seatback can reduce the effectiveness of the seat’ssafety belt in the event of a collision. Lift handle to move seat forward orbackward. Pull lever up to adjust seatback. Driver seat memory recliner (if equipped) • Pull control to adjust seatback. Seating and Safety Restraints 73

• To retain selected seatbackposition, release seatback bymoving memory recliner controlforward to release seatback. • Push seatback rearward until the seatback latches. This will be thefirst position selected. FOLDING REAR SEATS (IF EQUIPPED) FOLDING DOWN THE REAR SEATS To fold the seatback down: •...

To return the seat to the upright/normal seating position: • Rotate seat upward and latch. The full rear bench seat is shown. The split-folding rear seat (ifequipped) operates in a similar manner. SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and th...

suddenly or turns a corner sharply, or the vehicle receives an impact ofapproximately 8 km/h (5 mph) or more, the combination safety belts willlock to help reduce forward movement of the driver and passengers. Automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The be...

• Grasp the shoulder portion andpull downward until the entirebelt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automatic lockingmode. How to disengage the automatic locking mode Ford Motor Company recomm...

Front safety belt height adjustment (if equipped) Your vehicle has safety belt heightadjustments for the driver and frontpassenger. Adjust the height of theshoulder belt so the belt restsacross the middle of your shoulder. To lower the shoulder belt height,push the button and slide the heightadjuste...

BeltMinder The BeltMinder feature is a supplemental warning to the safety beltwarning function. This feature provides additional reminders to thedriver that the driver’s safety belt is unbuckled by intermittentlysounding a chime and illuminating the safety belt warning lamp in theinstrument cluster....

8. Confirmation of enabling BeltMinder is provided by: • The safety belt warning light flashing four times per second for threeseconds. • Followed by three seconds with the safety belt warning light off. • Once again, the safety belt warning light will flash four times persecond for three seconds. 9...

Children and air bags For additional important safetyinformation, read all information onsafety restraints in this guide. Children must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rearseating positions than in the frontseating posit...

If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in acollision. Determining if the system is operational The SRS uses a readiness light in the instrument cluster or ...

must put them in safety seats made especially for children. Check yourlocal and state or provincial laws for specific requirements regarding thesafety of children in your vehicle. Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child ...

way back on the seat cushion when the lower legs hang over the edge ofthe seat cushion. You may wish to discuss the special needs of your childwith your pediatrician. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the...

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap whichgoes over the back of the seat and hooks to an anchoring point. Tetherstraps are available as an accessory for many older safety seats. Contactthe manufacturer of your child seat fo...

STARTING Positions of the ignition 1. LOCK, locks the steering wheel,gearshift lever (automatic transaxle only)and allows key removal. On vehicles witha manual transaxle push the key in whileturning to lock. 2. ACCESSORY, allows the electricalaccessories such as the radio to operatewhile the engine ...

If you smell exhaust fumes inside your vehicle, have your dealerinspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important safety precautions A computer system controls the engine’s idle revolutions per minute(RPM). When the engine starts, the idle RPM runs faster to warm t...

Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate. Starting the engine Note: Whenever you start your vehicle, release the key as soon as the engine sta...

The ABS operates by detecting theonset of wheel lockup during brakeapplications and compensates forthis tendency. The wheels areprevented from locking even whenthe brakes are firmly applied. Theaccompanying illustration depictsthe advantage of an ABS equippedvehicle (on bottom) to a non-ABSequipped ...

3. Push and hold the thumb button. 4. Move the gearshift lever. If it is necessary to use the aboveprocedure to move the gearshiftlever, it is possible that a fuse hasblown and the vehicle’s brakelampsmay not be operating properly.Refer to Fuses and relays in the Roadside emergencies chapter. Do not...

Using the clutch Vehicles equipped with a manual transaxle have a starter interruptinterlock that prevents cranking of the engine unless the clutch pedal isdepressed. When starting a vehicle with a manual transaxle, you must: 1. Put the gearshift lever in theneutral position. 2. Hold down the brake ...

Parking your vehicle 1. Apply the brake and shift into theneutral position. 2. Set the parking brake. 3. Shift into 1 (First). 1 2 4 R 3 5 1 2 4 R 3 5 Driving 111

4. Turn engine off and remove thekey. Do not park your vehicle in Neutral, it may move unexpectedlyand injure someone. Use 1 (First) gear and set the parking brake fully. Recommended shift speeds Upshift according to the following charts for best fuel economy: Coupe Upshifts when accelerating(recomm...

Put the gearshift lever into theneutral position and wait at leastthree seconds before shifting into R(Reverse). You can shift into R (Reverse) only by moving the gearshift lever fromleft of 3 (Third) and 4 (Fourth) gears before you shift into R (Reverse).This is a special lockout feature which prev...

Hitches Do not use hitches that clamp onto the vehicle bumper. Use a loadcarrying hitch. You must distribute the load in your trailer so that 10% ofthe total weight of the trailer is on the tongue. Safety chains Always connect the trailer’s safety chains to the frame or hook retainersof the vehicle ...

• Use a lower gear when towing up or down steep hills. This willeliminate excessive downshifting and upshifting for optimum fueleconomy and transaxle cooling. • Anticipate stops and brake gradually. Exceeding the GCWR rating may cause internal transaxle damageand void your warranty coverage. Servici...

GETTING ROADSIDE ASSISTANCE To fully assist if you should have a vehicle concern, Ford Motor Companyoffers a complimentary roadside assistance program. This program isseparate from the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for the Basic warranty peri...

FUSES AND RELAYS Fuses If electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check the appropriatefuses before replacing any electricalcomponents. Note: Always replace a fuse with one that has the specified amperage r...

Passenger compartment fuse panel Coupe The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description DRL 10A Daytime Running Lamps HAZARD 15A Hazard Flasher ROOM 10A Engine Controls, RAP System,Radio, Shift Lock, CourtesyLamps, Starting System, Warn...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description METER 10A Backup Lamps, Engine Controls,Instrument Cluster, Rear WindowDefrost, Shift Lock, WarningChime, Turn Signal Switch WIPER 20A Wiper/Washer, Blower Relay STOP 15A Stop Lamps TAIL 15A Exterior Lamps, InstrumentIl...

Tire change procedure 1. Park on a level surface, activatehazard flashers and set the parkingbrake. When one of the front wheels is off the ground, the transaxlealone will not prevent the vehicle from moving or slipping off the jack, even if the vehicle is in P (Park) (automatic transaxle) or R(Reve...

JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes, andclothing, if contacted. Do not attempt to push-start your vehicle. ...

Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+)term...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingbelt. Ford Motor Company has notapproved a ...

FORD EXTENDED SERVICE PLAN You can get more protection for your new car or light truck bypurchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESPis an optional service contract which is backed by Ford Motor Companyor Ford Motor Service Company (in the U.S.) and Ford of Canada (inCanada). ...

taken to another dealer. If a particular dealership can not assist you,then contact the Customer Relationship Center. If you have questions or concerns, or are unsatisfied with the service youare receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at yourselling/se...

THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes • available free to owners and lessees of qualifying Ford Motor Companyvehicles The Dispute Settlement Board may not be available in all states. FordMotor...

Board membership The Board consists of: • three consumer representatives • a Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained byan independent consulting firm. The dealership Board member is chosenfrom Ford and Lincoln Mercury deale...

You will receive a letter of explanation if your application does notqualify for Board review. Oral presentations If you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral presentationbefore the Board, this is not a requireme...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) In those cases where you continue to feel that the efforts by Ford andthe dealer to resolve a factory-related vehicle service concern have beenunsatisfactory, Ford of Canada participates in an impartial third partymediation/arbitration program...

If your vehicle must be serviced while you are traveling or living inCentral or South America, the Caribbean, or the Middle East, contact thenearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANYWORLDWIDE DIRECT MARKET OPERATIONS1555 Fairlane DriveFairlane Busi...

WASHING THE EXTERIOR OF YOUR VEHICLE Never wash a vehicle that is “hot tothe touch” or during exposure tostrong, direct sunlight. It isrecommended that you wash yourvehicle regularly with cool orlukewarm water and a neutral Phshampoo, such as Detail Wash(ZC-3–A), which is available fromyour authoriz...

CLEANING THE ENGINE Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • The engine must be cool to the touch before spraying with water. • Never spray a hot engine with cold water, as damage to theengine block or engine co...

• 2.0L SOHC I4 engine • Cover the highlighted area to prevent water damage when cleaningthe engine. • Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage. WASHING NON-PAINTED PLASTIC EXTERIOR PARTS Use Detail Wash (ZC-3–A) for routine cleaning. If...

WASHING MIRRORS, MIRROR HOUSINGS AND REFLECTIVESURFACES Do not clean mirrors, mirror housings or reflective surfaces withabrasive materials or a dry cloth. Use a soft cloth and Detail Wash (ZC-3–A) mixed with water in order toclean the mirror housing. Use Glass Cleaner (E4AZ-19C507–AA) in orderto cl...

FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Your Ford, Lincoln or Mercury dealer has many quality products availableto clean your vehicle and protect its finishes. These quality productshave been specifically engineered to fulfill your automotive needs; theyare custom designed to complement the styl...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a scheduled maintenance guide which makes trackingroutine service easy. If your vehicle requires professional service, your dealership can providethe...

Working with the engine on • Automatic transaxle: 1. Set the parking brake and ensurethe gearshift is securely latched in P(Park). 2. Block the wheels to prevent thevehicle from moving unexpectedly. Note: Do not start your engine with the air cleaner removed and do not remove it while the engine is ...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel. 2. Go to the front of the vehicle and release the auxiliary latch that islocated under the front center of the hood. 3. Lift the hood and secure it with the prop rod. Maint...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.0L SOHC I4 engine 1. Engine oil dipstick 2. Brake fluid reservoir 3. Transmission fluid dipstick (automatic transaxle) 4. Battery 5. Air filter assembly 6. Engine oil filler cap 7. Power steering fluid reservoir 8. Engine coolant reservoir 9. Windsh...

2.0L DOHC Zetec engine 1. Transmission fluid dipstick (automatic transaxle) 2. Battery 3. Air filter assembly 4. Engine oil filler cap 5. Engine oil dipstick 6. Power steering fluid reservoir 7. Engine coolant reservoir 8. Windshield washer fluid reservoir 9. Brake fluid reservoir 9 8 7 1 2 3 4 6 5 ...

Note: Do not put washer fluid in the engine coolant reservoir. Washer fluid placed in the cooling system may harm engine and cooling systemcomponents. ENGINE OIL Checking the engine oil Refer to the scheduled maintenance guide for the appropriate intervalsfor checking the engine oil. 1. Make sure th...

• 2.0L DOHC Zetec engine 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is between the MIN and MAX marks, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below the MINmark, add enough oil to raise thelevel within the MIN-MAX range....

Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the normal range, add only certifiedengine oil of the recommended viscosity. Remove the engine oil filler capand use a funnel to pour the engine oil...

Ford production and aftermarket (Motorcraft) oil filters are designed foradded engine protection and long life. If a replacement oil filter is usedthat does not meet Ford material and design specifications, start-upengine noises or knock may be experienced. It is recommended you use the appropriate ...

Batteries normally produce explosive gases which can causepersonal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery,always shield your face and protect your eyes. Always provide properventilation. When lifting a plastic-case...

• If you do not allow the engine to relearn its idle trim, the idlequality of your vehicle may be adversely affected until the idletrim is eventually relearned. When the battery is disconnected or a new battery installed, thetransmission must learn its adaptive strategy. As a result of this, thetran...

Note: Automotive fluids are not interchangeable; do not use engine coolant, antifreeze or windshield washer fluid outside of its specifiedfunction and vehicle location. Adding engine coolant When adding coolant, make sure it is a 50/50 mixture of engine coolantand distilled water. Add the mixture to...

• Do not use alcohol, methanol or brine or any engine coolantsmixed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating orfreezing. • Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosi...

After any coolant has been added, check the coolant concentration seeChecking Engine Coolant section). If the concentration is not 50/50(protection to –34° F/–36° C), drain some coolant and adjust theconcentration. It may take several drains and additions to obtain a 50/50coolant concentration. When...

Severe climates If you drive in extremely cold climates (less than –36° C [–34° F]): • It may be necessary to increase the coolant concentrationabove 50%. • NEVER increase the coolant concentration above 60%. • Increased engine coolant concentrations above 60% willdecrease the overheat protection ch...

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tankmay cause leakage and lead to fuel spray and fire. The fuel system may be under pressure. If the fuel filler cap isventing vapor or if you hear a hissing sound, w...

Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materialsand any open flames beforefueling your vehicle. • Always turn off the vehicle beforefueling. • Automotive fuels can be harmfulor fatal if swallowed. Fuel such asgasoline is highly toxic and ifswallowed ...

The flow of fuel through a fuel pump nozzle can produce staticelectricity, which can cause a fire if fuel is pumped into an ungrounded fuel container. Use the following guidelines to avoid static build-up when filling anungrounded fuel container: • Place approved fuel container on the ground. • DO N...

more pronounced. If the problems persist, see your dealer or a qualifiedservice technician. It should not be necessary to add any aftermarket products to your fueltank if you continue to use high quality fuel of the recommended octanerating. Aftermarket products could cause damage to the fuel system...

• Use the same side of the same pump and have the vehicle facing thesame direction each time you fill up. • Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completel...

• Slow down gradually. • Driving at reasonable speeds (traveling at 88 km/h [55 mph] uses 15%less fuel than traveling at 105 km/h [65 mph]). • Revving the engine before turning it off may reduce fuel economy. • Using the air conditioner or defroster may reduce fuel economy. • You may want to turn of...

• Driving on flat terrain offers improved fuel economy as compared todriving on hilly terrain. • Transmissions give their best fuel economy when operated in the topcruise gear and with steady pressure on the gas pedal. • Close windows for high speed driving. EPA window sticker Every new vehicle shou...

CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the scheduled maintenanceguide for the service interval schedules. If adding fluid is necessary, useonly MERCON t ATF. • Coupe • Sedan 1. Start the engine and let it run until it reaches normal operatingtemperature (th...

BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked andrefilled as needed. Refer to thescheduled maintenance guide forthe service interval schedules. 1. Clean the reservoir cap beforeremoval to prevent dirt or waterfrom entering the reservoir. 2. Visually inspect the fluid leve...

CLUTCH FLUID (IF EQUIPPED) The clutch master cylinder andbrake master cylinder are part ofthe same system; both are refillablethrough the brake master cylinderwith brake fluid. For moreinformation on brake fluidmaintenance, refer to Brake fluid in this chapter. Brake fluid is toxic. If brake fluid c...

4. Latch the gearshift lever in P (Park) and leave the engine running. 5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. Ifnecessary, refer to Identifying components in the engine compartment in this chapter for the location of the dipstick. 6. Install the dipstick making sure...

If necessary, add fluid in 250 mL (1/2 pint) increments through the fillertube until the level is correct. If an overfill occurs, excess fluidshould be removed by a qualifiedtechnician. An overfill condition oftransmission fluid may cause shift and/or engagement concernsand/or possible damage. Check...

3. Fluid level should be at bottom ofthe opening. 4. Add enough fluid through thefiller opening so that the fluid levelis at the bottom of the opening. 5. Install and tighten the fill plugsecurely. Use only fluid that meets Ford specifications. Refer to Lubricant Specifications in this chapter. AIR ...

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning or peak traction characteristics. Temperature A B C The temperature grades are A (the highest), B, and C, representing the tire’sresistance to the gen...

• Four tire rotation Replacing the tires Replace the tires when the wearband is visible through the tiretreads. When replacing full size tires, never mix radial bias-belted, orbias-type tires. Use only the tire sizes that are listed on the Certification or Tire Label. Make sure that all tires are th...

Failure to follow these precautions may adversely affect thehandling of the vehicle and make it easier for the driver to lose control and roll over. Tires that are larger or smaller than your vehicle’s original tires may alsoaffect the accuracy of your speedometer. SNOW TIRES AND CHAINS Snow tires m...

Item Ford PartName orEquivalent Ford PartNumber FordSpecification Lock cylinder Penetrating andLock Lubricant XL-1 none Automatictransaxle MotorcraftMERCON t ATF XT-2-QDX MERCON t Manual transaxle Motorcraft MERCON t ATF XT-2-QDX MERCON t Engine oil Motorcraft SAE5W-20 SuperPremium MotorOil XO-5W20-...

1. World manufacturer identifier 2. Brake type and gross vehicleweight rating (GVWR) 3. Vehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number Engine number The engine number (the last eight numbers of the vehicle identificationnum...

FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of genuine Ford accessories are available for yourvehicle through your local authorized Ford, Lincoln, Mercury or Ford ofCanada dealer. These quality accessories have been specificallyengineered to fulfill your automotive needs; they are custom desi...

A Air bag supplementalrestraint system ..........................85 and child safety seats ..............87description ................................85disposal ......................................89driver air bag ............................87indicator light .....................12, 89operation ...

Fluid capacities .........................195 Foglamps .....................................42 Fuel ............................................175 calculating fuel economy .......180cap .....................................13, 177capacity ...................................195choosing the right fue...

V Vehicle dimensions ...................198 Vehicle Identification Number(VIN) ..........................................200 Vehicle loading ..........................113 Ventilating your vehicle ...........102 W Warning chimes ...........................14 Warning lights (see Lights) .......10 Wash...