Ford 2001 Windstar- Manuals

Turn signal control (pg. 82) Wiper/washer control (pg. 82) Instrument cluster (pg. 8) Driver air bag (pg. 144) Gearshift (includes O/D OFF control) (pg. 174) Traction control* (pg. 169) Speed control (pg. 79) Advanced tire warning control (pg. 231) Instrument panel dimmer control (pg. 28) Headlamp c...

WARNING LIGHTS AND CHIMES Some Warning Lights will show in the cluster equipped with a MessageCenter as words. Low fuel Illuminates as an early reminder of alow fuel condition indicated on thefuel gauge (refer to Fuel gauge in this chapter for more information).When refueling, after the lightcomes o...

wheelspin condition. It will be lit for a minimum of four seconds or for theduration of the Traction Control y event. For more information, refer to the Driving chapter. Traction Control Y off light (if equipped) Momentarily illuminates when theignition is turned to ON position andilluminates when t...

Anti-lock brake system (ABS) Momentarily illuminates when theignition is turned to the ON positionto ensure the circuit is functional. Ifthe light remains on or fails toilluminate, have the system servicedimmediately. With the ABS light on, the anti-lock brake system isdisabled and normal braking is...

One of the following conditions may exist: • low brake fluid level in the reservoir. • Brake force distribution system failure. The ABS light will alsoilluminate if this condition is present. O/D off Illuminates when the TransmissionControl Switch (TCS), refer to Overdrive control in the Controls an...

Temporary malfunctions may cause your Check Engine light to illuminate. Examples are: 1. The vehicle has run out of fuel. (The engine may misfire or runpoorly.) 2. Poor fuel quality or water in the fuel. 3. The fuel cap may not have been properly installed and securelytightened. These temporary malf...

It may take a long period of time for the system to detect animproperly installed fuel filler cap. For more information, refer to Fuel filler cap in the Maintenance and care chapter. Door ajar Illuminates when the ignition is inthe ON position and any door isopen. It may also momentarilyilluminate a...

Belt minder chime Sounds intermittently to remind you to fasten your safety belts. For information on the safety belt minder chime, refer to the Seating and safety restraints chapter. Supplemental restraint system (SRS) warning chime For information on the SRS warning chime, refer to the Seating and...

Fuel gauge Displays approximately how muchfuel is in the fuel tank (when thekey is in the ON position). The fuelgauge may vary slightly when thevehicle is in motion or afterrefueling. The ignition should be inthe OFF position while the vehicle isbeing refueled. When the gauge firstindicates empty, t...

Engine coolant temperature gauge Indicates the temperature of theengine coolant. At normal operatingtemperature, the needle remainswithin the normal area (the areabetween the “H” and “C”). If itenters the red section, the engine isoverheating. Stop the vehicle assoon as safely possible, switch offth...

MESSAGE CENTER (IF EQUIPPED) With the ignition in the ON position,the message center, located on yourinstrument cluster, displaysimportant vehicle informationthrough a constant monitor ofvehicle systems. You may selectdisplay features on the messagecenter for a display of status preceded by a brief ...

2. Pressing the RESET controlcycles the message center througheach of the language choices. 3. Press and hold the RESETcontrol to set the language choice. Units (English/Metric) 1. Select this function from theSETUP menu for the current unitsto be displayed. 2. Press the RESET control tochange from ...

Compass display (if equipped) The compass reading may be affected when you drive near largebuildings, bridges, power lines and powerful broadcast antenna. Magneticor metallic objects placed in, on or near the vehicle may also affectcompass accuracy. Usually, when something affects the compass readin...

5. Press and hold the RESETcontrol until the message centerdisplay changes to show the currentzone setting. 6. Release the reset control, thenslowly press down again. 7. Press the SETUP controlrepeatedly until the correct zonesetting for your geographic locationis displayed on the message center. To...

1. Drive the vehicle at least 8 km (5 miles) with the speed controlsystem engaged to display a stabilized average. 2. Record the highway fuel economy for future reference. It is important to press the RESET control after setting the speedcontrol to get accurate highway fuel economy readings. DIST TO...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parkinglamps. Rotate to the second positionto also turn on the headlamps. Daytime running lamps (DRL) (if equipped) Turns the highbeam headlamps on with a reduced output. To activate: • the key must be in the ON positio...

Flash to pass Pull toward you to activate andrelease to deactivate. Battery saver The battery saver will shut off the exterior lamps 10 minutes after theignition switch has been turned off and the headlamp control is in theHEADLAMP position. The system will not turn off the parking lamps ifthe headl...

AUTOLAMP CONTROL (IF EQUIPPED) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by the headlamp control. The autolamp system also keeps thelights on for a fixed period of timeafter the ignition switch is turned toOFF. • To turn autolamps o...

Manual heating and air conditioning system (if equipped) • Manual heating and air conditioning system without rearcontrols (if equipped) • Manual heating and air conditioning system with rear controls(if equipped) Fan speed control Controls the volume of air circulatedin the vehicle. A/C MAX A/C A/C...

Temperature control Controls the temperature of the airflow for the front part of thepassenger compartment. With the rear fan switch on the main control set to any fan speed(except OFF), the rear temperature control: • regulates the temperature of the airflow for the rear passengercompartment. • det...

Mode selector control The mode selector control allowsyou to adjust the direction of theairflow to the front part of thepassenger compartment. The air conditioning can operate in all modes. However, the airconditioning will only function if the outside temperature is about 6°C(43°F) or higher. Since...

Do not place objects on top of the instrument panel, as theseobjects may become projectiles in a collision or sudden stop. Rear passenger compartment climate control system (if equipped) This system allows the rear seat occupants to adjust their climatecomfort level. The rear seat climate control sy...

The rear climate system fan speedcontrol allows rear passengers tocontrol the volume of air that isdistributed from the rear registers. The temperature/mode selectioncontrol allows rear passengers toselect the temperature, as well aswhether the air is distributed fromthe overhead registers or the fl...

The defroster turns off automatically after 10 minutes or when theignition is turned to the OFF position. To manually turn off the defrosterbefore 10 minutes have passed, push the control again. USING YOUR AUDIO SYSTEM AM/FM Stereo Your vehicle is equipped with a delayed accessory feature. This feat...

Radio station memory preset The radio is equipped with four station memory preset controls. Thesecontrols can be used to select up to four preset AM stations and eightFM stations (four in FM1 and four in FM2). Setting memory preset stations 1. Select the frequency band with the AM/FM select control....

Speaker fade adjust (if equipped) Speaker sound can be adjustedbetween the front and rearspeakers. Press the TONE control four times,then use the volume knob to adjustthe desired level. Setting the clock Press CLK to toggle betweenlistening frequencies and clockmode. To set the hour, press and hold ...

information will display for ten seconds, when the radio is turned on, andthen revert to clock information. Anytime that the media is changed,(new radio station, etc.), the media information will again display for tenseconds before reverting back to the clock. In media mode, the mediainformation wil...

Turn the control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition switch is turned back on. AM/FM select The AM/FM select control works inradio, tape and CD changer modes(if...

• Press to move to the next frequency up the band (whether or not a listenable station is located there). Hold for quick movement. Tune adjust for CD changer (if equipped) • Press to select the previous disc in the CD changer. (Play willbegin on the first track of thedisc unless the CD changer is in...

Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stationson the frequency band. Press the SCAN control again to stop the scanmode. Scan function in CD changer mode (if equipped) Press the SCAN control to hear a brief sampling of all selections on theCD. (...

Treble adjust The treble adjust control allows youto increase or decrease the audiosystem’s treble output. Speaker balance adjust Speaker sound distribution can beadjusted between the right and leftspeakers. Speaker fade adjust Speaker sound can be adjustedbetween the front and rearspeakers. Tape se...

Automatic Music Search The Automatic Music Search featureallows you to quickly locate thebeginning of the tape selectionbeing played or to skip to the nextselection. To activate the feature, momentarilydepress the TAPE AMS button.Then, press either REW (for the beginning of the current selection) or...

Fast forward The fast forward control works in tape and CD changer modes. To fast forward in tape mode, pressthe 1–2/FF control. Tape direction will automaticallyreverse when the end of the tape isreached. Press the SIDE/REW control to stopthe fast forward of the tape. To fast forward in CD changerm...

• to decrease minutes and • to increase minutes. The CLK control will allow you to switch between media display mode(radio station, stereo information, etc.) and clock display mode (time).When in clock mode, the media information will display for 10 seconds,when the radio is turned on, and then reve...

Tune adjust The tune control works in radio or CD changer mode. Tune adjust in radio mode • Press to move to the next frequency down the band(whether or not a listenablestation is located there). Hold thecontrol to move through thefrequencies quickly. • Press to move to the next frequency up the ban...

Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns,indicating the station is held in memor...

Bass adjust The bass adjust control allows youto increase or decrease the audiosystem’s bass output. Press the BASS control then press: • to decrease the bass output and • to increase the bass output. Treble adjust The treble adjust control allows youto increase or decrease the audiosystem’s treble ...

Press the FADE control then press: • to shift the sound to the front and • to shift the sound to the rear. Tape/CD select • To begin tape play (with a tapeloaded into the audio system)while in the radio or CD mode,press the TAPE control. Press thebutton during rewind or fast forward to stop the rewi...

• In the tape mode, tape direction will automatically reverse when theend of the tape is reached. • In CD mode, pressing the control fast forwards the CD within thecurrent track. Tape direction select Press SIDE 1–2 to play the alternateside of a tape. Eject function Press the EJ control to stop and...

• to decrease minutes and • to increase minutes. If your vehicle has a separate clockmodule, (other than the digital radiodisplay), the CLK button will notfunction in the above manner. The CLK button will allow you toswitch between media display mode(radio station, stereo information,etc.) and clock...

To turn on the rear seat controls, press the memory preset controls 3and 5 at the same time. The will appear in the radio display. Pressing 3 and 5 at the same time again will turn the rear seat controls off. If there is a discrepancy between the rear seat and the front audiocontrols, (i.e, both try...

Premium AM/FM Stereo In Dash Six CD Radio Volume/power control Press the control to turn the audiosystem on or off. Turn the control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when the...

AM/FM select The AM/FM select control works inradio and CD modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press thecontrol to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in CD mode Press this control to stop CD play and begin radi...

Setting memory preset stations 1. Select the frequency band with the AM/FM select control. Press theAM/FM control to toggle between AM, FM1, or FM2. 2. Press the SEEK control to access the next listenable station up ordown the frequency band. Press the TUNE control to go up or down thelistening band...

• Religious • Rock • Soft • Top 40 Show This feature allows you to select thetype of RDS broadcast informationthe radio will regularly show in thedisplay. With RDS activated, press theMENU control until SHOW isdisplayed. Use the SEL control to select TYPE(displays the RDS program type:rock, jazz, et...

Cleaning compact discs Inspect all discs for contamination before playing. If necessary, cleandiscs only with an approved CD cleaner and wipe from the center out tothe edge. Do not use circular motion. CD and CD changer care • Handle discs by their edges only. Never touch the playing surface. • Do n...

Radio reception factors Three factors can affect radio reception: • Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km(24 miles). This range can be affected by “signal modulation.” Signalmodulation is a process...

If the vehicle sustains damage to the rear bumper/fascia, leavingit misaligned or bent, the sensing zone may be altered causinginaccurate measurement of obstacles or false alarms. POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedalshould only be adjusted when thevehicle is sto...

POSITIONS OF THE IGNITION 1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning. 2. LOCK, locks the steering wheel,automatic transmission gearshiftlever and allows key removal. 3. OFF, shuts off the engine and allaccessories without locking thestee...

To turn speed control off • Press OFF or • Turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speedwill be erased. To set a speed • Press SET+. For speed control tooperate, the speed control mustbe ON and the vehicle speedmust be greater than 48 km/h (30...

You can accelerate with the accelerator pedal at any time during speedcontrol usage. Releasing the accelerator pedal will return your vehicle tothe previously programmed set speed. To set a lower set speed • Press and hold CST −. Releasethe control when the desiredspeed is reached or • Press and rel...

Rear window wiper/washer controls For rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select: INT 2 — One second interval rearwiper. INT 1 — Ten second interval rear wiper. OFF — Rear wiper and washer off. For rear wash cycle, rotate (and hold as desired) ...

TILT STEERING WHEEL (IF EQUIPPED) Pull the tilt steering control towardyou to move the steering wheel upor down. Hold the control whileadjusting the wheel to the desiredposition, then release the control tolock the steering wheel in position. Never adjust the steering wheel when the vehicle is movin...

POWER WINDOWS (IF EQUIPPED) Press and hold the rocker switches to open and close windows. • Press the top portion of therocker switch to close. • Press the bottom portion of therocker switch to open. One touch down • Press AUTO completely down andrelease quickly. The driver’swindow will open fully. ...

Accessory delay With accessory delay, the window switches may be used for up to tenminutes after the ignition switch is turned to the OFF position or untilany door is opened. Power vent windows (if equipped) Your vehicle may be equipped withrear power vent windows which areoperated the same as the f...

POWER DOOR LOCKS (IF EQUIPPED) Press control to unlock all doors. Press control to lock all doors. Memory lock If you lock your doors with the power lock switch or the remotetransmitter while the sliding door is open, the door will automaticallylock after it is closed. Smart locks With the key in th...

MEMORY SEATS/REARVIEW MIRRORS/ADJUSTABLE PEDALS(IF EQUIPPED) This system allows automaticpositioning of the driver seat,outside rearview mirrors, andadjustable pedals to twoprogrammable positions. The memory seat control is locatedon the driver door. • To program position one, movethe driver seat to...

1. Prepare for programming theHomeLink t Universal Transceiver by erasing the three factory defaultcodes by holding down the twooutside buttons until the red lightbegins to flash after 20 seconds.Release both buttons. 2. Hold the end of your hand-heldtransmitter 5–14 cm (2–5 inches) away from the Ho...

3. Press and release theprogrammed HomeLink t button. Press and release the HomeLink t button a second time to complete the training process. (Some garagedoor openers may require thisprocedure to be done a third timeto complete the training). The 2nd or 3rd press from step 3 will activate the door. ...

Operating TravelNote T TravelNote t records and stores messages for up to three minutes in total length with simple controls. When you get an idea or remembersomething important while you’re driving, you don’t have to try toscribble it down or pull off the side of the road. All you have to do ispush...

Rear courtesy/reading lamps (if equipped) The courtesy lamp lights can beturned on with rocker switch at anytime. Rear dome lamp The dome lamp lights when: • any door is opened. • the instrument panel dimmerswitch is held up until thecourtesy lamps come on. • any of the remote entry controlsare pres...

Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety ofaftermarket garage door openers: • Remove the storage clip from theaftermarket transmitter. • Place Velcro y hook onto side of aftermarket transmitter oppositeof actuator control. • Plac...

Opening the PSD With the ON/OFF control in the ON position, either sliding door can beopened by: • operating the remote transmitter. Refer to Remote Entry System in this chapter. • pushing and releasing the overhead console right hand or left handcontrol • pushing and releasing the right hand or lef...

Safety/Obstructions If anything obstructs the Power Sliding Door while it is closing, the doorwill automatically reverse to the open position, provided it meetssufficient resistance. Resetting the PSD The power sliding door may operate incorrectly or not at all because ofthe following condition: • a...

To install floor mats that have a screw in retainer: 1. Move the driver’s seat to the most rearward position 2. Position the driver’s side floor mat with the rear of the mat against left(outboard) front edge of seat track mounting bracket. 3. Use a screwdriver to screw locator post into vehicle carp...

Unlocking the doors • 3–button remote • 4–button remote • 5–button remote Press this control to unlock the driver door and disarm the anti-theftsystem (if equipped). The interior lamps will illuminate. Press the control again within three seconds to unlock all doors andliftgate. If the control is pr...

Opening power sliding doors • 4–button remote • 5–button remote Press this control twice within three seconds to open the power slidingdoor (if equipped). The interior lamps will illuminate. Press this controlanother two times within three seconds to close the power sliding doorand turn off the inte...

Locking the doors • 3–button remote • 4–button remote • 5–button remote Press this control to lock all doors and liftgate, turn off the interior lights(if they were on) and arm the perimeter anti-theft system (if equipped). To confirm doors/hood are closed and locked, press the control a secondtime ...

Sounding a panic alarm • 3–button remote • 4–button remote • 5–button remote Press this control to activate the personal panic alarm. The personal panic alarm will cycle the horn and turn signals on/off plusilluminate the interior lights. To deactivate the alarm, press the control again or turn the ...

Illuminated entry The interior lights will illuminate when the remote entry Unlock or Paniccontrol is pressed with the doors closed or when unlocking or opening apower sliding door (if equipped). The system automatically turns off after 25 seconds or when the ignitionis turned to the RUN position. T...

To replace the battery: 1. Twist a thin coin between the twohalves of the transmitter near thekey ring. DO NOT TAKE THEFRONT PART OF THETRANSMITTER APART. 2. Place the positive (+) side of newbattery in the same orientation.Refer to the diagram inside thetransmitter unit. 3. Snap the two halves back...

• 5–button remote If a transmitter has been lost or if you would like to purchase additionaltransmitters for your vehicle (up to four may be programmed intomemory), take all your vehicle’s transmitters to your dealer or perform the reprogramming procedure yourself. It will be necessary to reprogram ...

Activating/deactivating the memory feature on your remote transmitter The memory feature from the remote transmitter can be turned off/on,however, the memory control buttons will continue to operate. Beforefollowing the procedure, make sure that the ignition is OFF and all doorsand the liftgate wind...

KEYLESS ENTRY SYSTEM With the keyless entry keypad, you can: • lock or unlock the vehicle doors without using the key. Your vehicle has a factory set 5 digit code that operates the keyless entrysystem. You can also program your own 5 digit personal entry code. Thefactory-set code is located: • on th...

Unlocking the doors with the keyless entry system To unlock the driver door, enter either the factory set code or thepersonal code (each digit must be pressed within five seconds of theprior digit). The interior lamps will also illuminate. To unlock all doors, enter the factory set code or personal ...

Automatic disarming Switching the ignition to the 4 (ON) position with a coded key disarms the vehicle. The THEFT light will illuminate for three seconds and then go out. If the THEFT light stays on for an extended period of time or flashes rapidly, have the system serviced by your dealership or aqu...

If your keys are lost or stolen youwill need to do the following: • Use your spare key to start thevehicle. or • Have your vehicle towed to adealership or locksmith. The keycodes will need to be erased fromyour vehicle and new key codes will need to be re-coded. Replacing coded keys can be very cost...

LIFTGATE To unlock the liftgate, insert doorkey into the lock and turnclockwise. You can also unlock thelatch (but not release it) with thepower door lock system and remoteentry key fob. To open the liftgate, squeeze theliftgate handle. • Do not open the liftgate in agarage or other enclosed areawit...

Cargo Area Features Cargo net (if equipped) The cargo net secures lightweight objects in the cargo area. Attach thenet to the anchors provided. Do not put more than 22 kg (50 lbs.) in thenet. This net is not designed to restrain objects during a collision. Utility hooks (if equipped) The utility hoo...

SEATING Adjustable head restraints (if equipped) Your vehicle’s seats may be equipped with head restraints which arevertically adjustable. The purpose of these head restraints is to help limithead motion in the event of a rear collision. To properly adjust your headrestraints, lift the head restrain...

Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. Reclining the seatback can reduce the effectiveness of the seat’ssafety belt in the event of a collision. Lift handle to move seat forward orbackward. Pull lever up to adjust seatback. Adjusting the power ...

Using the power lumbar support (if equipped) The power lumbar control is locatedon the inboard side of the seat. Press one side of the control toadjust firmness. Press the other side of the controlto adjust softness. Memory seats/rearview mirrors/adjustable pedals (if equipped) This system allows au...

The head restraints can be movedup and down. Push control to lower head restraint. Seat mounted cup holders (if equipped) Your vehicle may be equipped with cupholders mounted on the outboardsides of the second row seat(s). The cupholder is designed to detachfrom the seat when subjected to a heavy lo...

Accessing the 3rd row seat If your vehicle has an adjustable 2nd row bench seat or 2nd row bucketconsole seat, it can be adjusted to allow easier access to the 3rd row seatby sliding the seat forward, folding the seatback to the forward flatposition, or using the recline control to adjust seatback f...

Bench seat or Bucket Console seat To remove the seats: 1. (For 2nd row bench seat only.)Disengage the lap/shoulder belt fromthe side of the seat belt detachanchors (if equipped) by insertingthe seatbelt tongue or a key into theslot in the detachable anchor andlifting upward. Seating and safety restr...

2. (For 2nd row bench seat only.) Using the clip attached to the end ofthe shoulder belt(s), clip the end of the belt to the stationary portion ofthe shoulder belt coming out of the trim panel. The end of the shoulderbelt must be clipped in order to keep it from striking anything during vehicle oper...

Bucket seats To remove the seat(s): Position the seatback in the full down position to make removing theseat easier. 1. From behind the seat, pullstraight back on the release controlslocated on each side of the seat,releasing the rear floor latches. 2. Lift up the back of the seat by the release con...

SAFETY RESTRAINTS Personal Safety System The Personal Safety System provides an improved overall level of frontalcrash protection to front seat occupants and is designed to help furtherreduce the risk of air bag-related injuries. The system is able to analyzedifferent occupant conditions and crash s...

collisions, not rollovers, side-impacts, or rear-impacts unless the collisioncauses sufficient longitudinal deceleration. Driver and passenger dual-stage air bag supplemental restraints The dual-stage air bags offer the capability to tailor the level of air baginflation energy. A lower, less forcefu...

Air bags can kill or injure a child in a child seat. NEVER place a rear-facing child seat in front of an active air bag. If you must use a forward-facing child seat in the front seat, move the seat all theway back. Always transport children 12 years old and under in the backseat and always properly ...

Determining if the Personal Safety System is operational The Personal Safety System uses a warning light in the instrumentcluster or a back-up tone to indicate the condition of the system. Referto the Restraints Warning Light section in the Instrumentation chapter. Routine maintenance of the Persona...

All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even when an air bag SRS is provided. It is extremely dangerous to ride in a cargo area, inside oroutside of a vehicle. In a collision, people riding in these areas are more likely to be seriously inju...

2. To unfasten, push the releasebutton and remove the tongue fromthe buckle. The front and rear outboard safety restraints in the vehicle arecombination lap and shoulder belts. The front and rear seat passengeroutboard safety belts have locking cinch tongues described below: Safety belts with lockin...

How to fasten the cinch tongue 1. Pull the combination lap and shoulder belt from the retractor so thatthe shoulder belt portion of the safety belt crosses your shoulder andchest. 2. Be sure the belt is not twisted. If the belt is twisted, remove the twist. 3. Insert the belt tongue into the proper ...

Failure to replace the Belt and Retractor assembly after anaccident could increase the risk of injury in a collision. Lap belts Adjusting the center lap belt The lap belt does not adjust automatically. The lap belt should fit snugly and as low as possible around thehips, not across the waist. Insert...

One time disable Anytime the safety belt is buckled and then unbuckled during an ignitionON cycle, Belt Minder will be disabled for that ignition cycle only. Deactivating/activating the belt minder feature Read steps 1 - 9 thoroughly before proceeding with thedeactivation/activation programming proc...

6. Within seven seconds of the safety belt warning light turning off,buckle then unbuckle the safety belt. • This will disable Belt Minder if it is currently enabled, or enable BeltMinder if it is currently disabled. 7. Confirmation of disabling Belt Minder is provided by flashing thesafety belt war...

Replacing the front passenger and second row bench seat beltassemblies after a collision All front passenger and second row bench seat belt assemblies adjacentto a sliding door have special energy management retractors designed tofurther reduce the risk of injury in the event of a head-on collision....

air bags plus safety belts in impacts for which the air bags are designedto deploy, and air bags do not offer any protection in crashes for whichthey do not deploy. Important supplemental restraint system (SRS) precautions The supplemental restraint systemis designed to work with the safetybelt to h...

Do not put anything on or over the air bag module. Placingobjects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causingserious injury. Do not attempt to service, repair, or modify the Air BagSupplemental Restraint System or its ...

Determining if the system is operational The supplemental restraint system uses a warning indicator in theinstrument cluster or a back-up tone to indicate the condition of thesystem. Refer to the Restraints Warning Indicator section in the Instrumentation chapter. Routine maintenance of the air bag ...

The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion ...

How does the side air bag system work? The side air bag system consists ofthe following: • An inflatable nylon bag (air bag)with a gas generator concealedbehind the outboard bolster ofthe driver and front passengerseatbacks. • A special seat cover designed toallow airbag deployment. • The same warni...

Several air bag systemcomponents get hot after inflation. Do not touch them afterinflation. If the side air bag hasdeployed, the air bag will not function again. The sideair bag system (including theseat) must be inspected andserviced by a qualifiedtechnician in accordance withthe vehicle service ma...

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant orchild restraint you might use. When possible, always place children under age 12...

SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all of the manufacturer’s instructions with thesafety seat you put in your vehicle. If you do not install and use thesafety seat properly, the ...

5. Insert the belt tongue into theproper buckle for that seatingpositions until you hear a snap andfeel it latch. Make sure the tongue issecurely latched to the buckle bypulling on the tongue. 6. While pushing down with yourknee on the child seat pull up onthe shoulder belt portion to tightenthe lap...

2. Place the child safety seat in the center seating position. 3. Route the tongue and webbing through the child seat according to thechild seat manufacturer’s instructions. 4. Insert the belt tongue into the proper buckle for the center seatingposition until you hear a snap and feel it latch. Make ...

The tether can be attached directly to the rear of all passenger seatingexcept the front passenger seat equipped with power adjustment. Thefront passenger seat with manual adjustment does have a tether anchor. Front passenger seating position (manual adjusting seats only) 1. Position the child safet...

8. Tighten the child safety seattether strap according to themanufacturer’s instructions. Rear seating positions Follow steps 1–8 as described above for the following available seats: • 2nd row bucket • 2nd row bench Seating and safety restraints 160

Do not attach a child seat to any lower anchors used for childseat installation if an adjacent child seat is attached to that anchor. In a crash, one anchor may not be strong enough to hold twochild seat attachments and may break, causing serious injury or death. The lower anchors for child seatinst...

PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. Thissystem meets all Canadian Interference-Causing Equipment standardrequirements regulating the impulse electrical field strength of radionoise. When starting a fuel-injected engine, avoid pressing the a...

• If the driver’s safety belt is fastened, the light may not illuminate. • When the key is turned to the 4 (ON) position, the fuel pump isactuated for a few seconds equalizing the fuel pressure for properstarting. STARTING THE ENGINE NOTE: Whenever you start your vehicle, release the key as soon as ...

BRAKES Your service brakes are self-adjusting. Refer to the scheduledmaintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate aperformance concern with the vehicle’s brake system. In normaloperation, automotive brake systems may emit occasional or int...

ABS warning lamp ABS The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does notilluminate momentarily at start up or remains on the ABS needs to beserviced. With the ABS light on, the anti-lockbrake system is disabled ...

The AdvanceTrac y on/off control button allows the driver to controlthe availability of the TractionControl y and AdvanceTrac y system. This is independent of theABS function, which can NOT be switched off by the driver. The AdvanceTrac y system status is indicated by a “TRAC ACTIVE”indicator light ...

R (Reverse) With the gearshift lever in R(Reverse), the vehicle will movebackward. You should always cometo a complete stop before shiftinginto and out of R (Reverse). N (Neutral) With the gearshift lever in the N(Neutral) position, the vehicle canbe started and is free to roll. Holdthe brake pedal ...

When to use (Overdrive) or press the O/D OFF switch You will notice that there is only onedrive position ( [Overdrive]) on your gearshift indicator (instead ofDrive and Overdrive). However, youwill find a control labeled O/Dlocated on the gearshift lever. Push in the switch and the O/D OFF lightin t...

When parking, do not use the gearshift in place of the parkingbrake. Always set the parking brake fully and make sure that the gearshift is securely latched in Park (P). Turn off the ignitionwhenever you leave your vehicle. Never leave your vehicle unattendedwhile it is running. If you do not take t...

Always ensure that the weight of passengers, cargo and equipment beingcarried is within the weight limitations that have been established foryour vehicle including both gross vehicle weight and Front and reargross axle weight rating limits. Under no circumstance should theselimitations be exceeded. ...

• Do not tow a trailer until your vehicle has been driven at least 800 km(500 miles). • Refer to the instructions included with towing accessories for theproper installation and adjustment specifications. If your vehicle is equipped with the optional heavy duty trailer towwiring, it is pre-wired for...

Hitches Do not use hitches that clamp onto the vehicle bumper. Use a loadcarrying hitch. You must distribute the load in your trailer so that 10% ofthe total weight of the trailer is on the tongue. Safety chains Always connect the trailer’s safety chains to the hook retainers on thehitch. To connect...

Driving while you tow When towing a trailer: • Ensure that you turn off your speed control. The speed control mayshut off automatically when you are towing on long, steep grades. • Consult your local motor vehicle speed regulations for towing a trailer. • Use a lower gear when towing up or down stee...

GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford offers acomplimentary roadside assistance program. This program is separatefrom the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for the Basic warranty period (Canada) o...

The fuel pump shut-off switch islocated behind the service panel onthe right side of the cargo area. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump s...

NOTE: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wiredamage and could start a fire. Standard fuse amperage rating and color COLOR Fuse Rating Mini Fuses Standard Fuses Maxi Fuses Cartridge Maxi Fuses Fuse Link Ca...

The fuses are coded as follows: Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 10A Right Stepwell Lamp, Left Stepwell Lamp,Right Puddle Lamp, Left Puddle Lamp, Left2nd Row Reading Lamp, Right 2nd RowReading Lamp, Left 3rd Row ReadingLamp, Right 3rd Row Reading Lam...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 5 20A Console Power Point 6 15A Radio, Compact Disc Changer, RemoteKeyless Entry Module, PSD (Power SlidingDoor) Module RH and LH, Rear Seat RadioController (if equipped), Rear SeatEntertainment Module (if equipped) 7 1...

Always disconnect the battery before servicing high currentfuses. Always replace the cover to the Power Distribution Box beforereconnecting the battery or refilling fluid reservoirs. If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and care chapte...

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 201 — Not Used 202 — Front Wiper ON/OFF Relay 203 — Rear Wiper Relay 204 — A/C Clutch Relay 205 — Horn Relay 206 — Not Used 207 — Fuel Pump Relay 208 — Not Used 209 — Front Wiper Hi/Low Relay 301 — Low Speed Engine Cooling Fan Re...

If you use the temporary spare tire continuously or do not followthese precautions, the tire could fail, causing you to lose control of the vehicle, possibly injuring yourself or others. When driving with the temporary spare tire do not: • exceed 80 km/h (50 mph) under any circumstances • load the v...

Removing the spare tire 1. Open the liftgate and open the plastic cover from the carpeting oncargo floor to expose the hex nut. On cargo van model, lift flap in mat toexpose hex nut. 2. Insert the lug nut wrench on thehex nut in cargo floor. 3. Turn the wrenchcounterclockwise until tire islowered to...

Stowing the spare or flat tire 1. Lay the tire on the ground with the interior side facing up. 2. Install the retainer through thewheel center and slide the wheelunder the vehicle. 3. Turn the lug nut wrenchclockwise until the tire is raised toits original position underneath thevehicle. The hex nut...

16. Put flat tire, jack and lug wrench away in the proper stowagelocations. JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. You could damage the ...

Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+)term...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed by wheel lift or flatbedequipment. Do not tow with a slingbelt. Ford Motor Company has notapproved a slin...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a scheduled maintenance guide which makes trackingroutine service easy. If your vehicle requires professional service, your dealership can providethe...

Do not start your engine with the air cleaner removed and donot remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel. 2. Go to the front of the vehicle and release the auxiliary latch tha...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.8L OHV V6 engine 1. Brake fluid reservoir 2. Air filter assembly 3. Power distribution box 4. Battery 5. Automatic transmission fluid dipstick 6. Engine oil dipstick 7. Engine oil filler cap 8. Windshield washer fluid reservoir 9. Engine coolant res...

ENGINE OIL Checking the engine oil Refer to the scheduled maintenance guide for the appropriate intervalsfor checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into theoil pan. 3. Set the parking brake and ensure t...

• If the oil level is below the MINmark, add enough oil to raise thelevel within the MIN-MAX range. • Oil levels above the MAX mark may cause engine damage. Some oilmust be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil ...

BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked andrefilled as needed. Refer to thescheduled maintenance guide forthe service interval schedules. 1. Clean the reservoir cap beforeremoval to prevent dirt or waterfrom entering the reservoir. 2. Visually inspect the fluid leve...

WINDSHIELD WASHER FLUID Washer fluid Check the washer fluid wheneveryou stop for fuel. The reservoir ishighlighted with a symbol. If the level is low, add enough fluidto fill the reservoir. In very coldweather, do not fill the reservoir allthe way. Only use a washer fluid that meets Ford specificati...

equates to a freeze point of -36° C (-34°F). Coolant concentration testingis possible with a hydrometer or antifreeze tester (such as the RotundaBattery and Antifreeze Tester, 014-R1060). The level of coolant shouldbe maintained at the 9 cold full 9 of 9 cold fill range 9 level in the coolant reserv...

• Refer to the Scheduled Maintenance Guide for service intervalschedules. • Be sure to read and understand Precautions when servicing your vehicle in this chapter. If the engine coolant has not been checked at the recommended interval,the engine coolant reservoir may become low or empty. If the rese...

• Do not add/mix an orange-colored, exteded life coolant such asMotorcraft Speciality Orange Engine Coolant, VC-2 (US) orCXC-209 (Canada), meeting Ford specification WSS-M97B44-Dwith the factory-filled coolant. Mixing Motorcraft Speciality Orange Engine Coolant or any orange-colored extended life pr...

4. When you are sure that all the pressure has been released, use thecloth to turn it counterclockwise and remove the cap. 5. Fill the coolant reservoir slowly with the proper coolant mixture (seeabove), to within the 9 cold fill range 9 or the 9 cold full 9 level on the reservoir. If you removed th...

Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Refill capacities in the Capacities and specifications chapter. Fill your engine coolant reservoir as outlined in Adding engine coolant in this chapter. Severe climates If you drive in extremely cold c...

CHECKING AND ADDING POWER STEERING FLUID • 3.8L OHV V6 engine Check the power steering fluid. Refer to the scheduled maintenanceguide for the service interval schedules. If adding fluid is necessary, useonly MERCON t ATF. 1. Start the engine and let it run until it reaches normal operatingtemperatur...

5. If the fluid is low, add fluid in small amounts, continuously checkingthe level until it reaches the correct operating range. Be sure to put thecap back on the reservoir. TRANSMISSION FLUID Checking automatic transmission fluid Refer to your scheduled maintenance guide for scheduled intervals for...

Correct fluid level The transmission fluid should be checked at normal operatingtemperatures 66°C-77°C (150°F-170°F) on a level surface. The normaloperating temperature can be reached after approximately 30 km (20miles) of driving. The transmission fluid should be inthis range if at normal operating...

BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. However, for severe usage or in high temperature climates, check thebattery electrolyte level. Refer to the scheduled maintenance guide forthe service ...

Batteries normally produce explosive gases which can causepersonal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery,always shield your face and protect your eyes. Always provide properventilation. When lifting a plastic-case...

2. Put the gearshift in P (Park), turn off all accessories and start theengine. 3. Run the engine until it reaches normal operating temperature. 4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine to idle for at least one minute. 6. With your foot on the brak...

Checking the wiper blades If the wiper blades do not wipe properly, clean both the windshield andwiper blades using undiluted windshield wiper solution or a milddetergent. Rinse thoroughly with clean water. To avoid damaging theblades, do not use fuel, kerosene, paint thinner or other solvents. Chan...

which all passenger car tires must meet under the Federal Motor VehicleSafety Standard No. 109. Grades B and A represent higher levels ofperformance on the laboratory test wheel than the minimum required bylaw. The temperature grade for this tire is established for a tire thatis properly inflated an...

• Four tire rotation Replacing the tires Replace the tires when the wearband is visible through the tiretreads. When replacing full size tires, never mix radial bias-belted, orbias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same s...

Failure to follow these precautions may adversely affect thehandling of the vehicle and make it easier for the driver to lose control and roll over. Tires that are larger or smaller than your vehicle’s original tires may alsoaffect the accuracy of your speedometer. SNOW TIRES AND CHAINS Driving too ...

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tankmay cause leakage and lead to fuel spray and fire. The fuel system may be under pressure. If the fuel filler cap isventing vapor or if you hear a hissing sound, w...

Fuel Filler Cap Your fuel tank filler cap has an indexed design with a 1/8 turn on/offfeature. When fueling your vehicle: 1. Turn the engine off. 2. Carefully turn the filler cap counterclockwise 1/8 of a turn until it stops. 3. Pull to remove the cap from the fuel filler pipe. 4. To install the cap...

amount of fuel in a full tank and a tank when the fuel gauge indicatesempty. Empty reserve is the small amount of fuel remaining in the fueltank after the fuel gauge indicates empty. The amount of usable fuel in the empty reserve varies and shouldnot be relied upon to increase driving range. When re...

Keep a record for at least one month and record the type of driving (cityor highway). This will provide an accurate estimate of the vehicle’s fueleconomy under current driving conditions. Additionally, keeping recordsduring summer and winter will show how temperature impacts fueleconomy. In general,...

• Use recommended engine oil. Refer to Lubricant Specifications. • Perform all regularly scheduled maintenance items. Follow therecommended maintenance schedule and owner maintenance checksfound in your vehicle scheduled maintenance guide. Conditions • Heavily loading a vehicle or towing a trailer m...

Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test ofthe on-board diagnostics system. If your “Check Engine/Service EngineSoon” light is on, refer to the description in the Warning Lights and Chimes section of the Instrumentation ...

Replacing headlamp bulbs To remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position, then open the hood. Note size and location of retainerpins for installation. 2. At the back of the headlamp, pulltwo retainer pins up to release theheadlamp assembly. 3. Pull headlamp assembly forw...

To install the new bulb: Handle a halogen headlamp bulb carefully and keep out ofchildren’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb tobreak the next time the headlamps are operated. 1. With the flat side of the new bulb’s...

3. Remove bulb socket by turning itcounterclockwise, then slide it outof the lamp assembly. 4. Carefully pull bulb straight out ofthe socket and push in the newbulb. 5. To complete installation, followremoval procedure in the reverseorder. Replacing tail lamp/backup/turn lamp bulbs 1. Open the liftg...

Replacing license plate lamp bulbs 1. Remove two screws and thelicense plate lamp assembly fromthe liftgate. 2. Remove bulb socket by pulling itstraight out of the lamp assembly. 3. Carefully pull the bulb out fromthe socket and push in the newbulb. 4. Push bulb socket in to the lampassembly. 5. Ins...

Vertical aim adjustment 1. Park the vehicle on a level surface approximately 7.6 meters (25 feet)from a vertical wall or screen directly in front of it. • (A) Eight feet • (B) Center height of lamp to ground • (C) Twenty five feet • (D) Horizontal reference line 2. Measure the height from the center...

5. Locate the vertical adjuster on each headlamp, then use an E8 Torxsocket to turn the adjuster either counterclockwise (to adjust up) orclockwise (to adjust down) positioning the horizonal edge of the highintensity light on the horizontal reference line. 6. HORIZONTAL AIM IS NOT REQUIRED FOR THIS ...

Waxing your vehicle Waxing your vehicle on a regular basis will reduce minor scratches andpaint damage. Wax when water stops beading on the surface. This could be every threeor four months, depending on operating conditions. Use only carnauba or synthetic-based waxes. Use a cleaning fluid with aclea...

Cleaning mirrors Do not clean your mirrors with a dry cloth or abrasive materials. Use asoft cloth and mild detergent and water. Be careful when removing icefrom outside mirrors because you may damage the reflective surface. Cleaning the exterior lamps Wash with the same detergent as the exterior of...

• Cover the highlighted areas to prevent water damage when cleaningthe engine. • Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage. Cleaning the instrument panel Clean with a damp cloth, then dry with a dry cloth. Avoid cleaner or polish that in...

Cleaning leather seats (if equipped) To clean, simply use a soft cloth dampened with water and a mild soap.Wipe the leather again with a damp cloth to remove soap residue. Drywith a soft cloth. For tougher soiling concerns, Ford recommends usingthe Deluxe Leather Care Kit F8AZ-19G253–AA, which is av...

REFILL CAPACITIES Fluid Ford PartName Application Capacity Brake fluid 1 All Fill to MAX lineon reservoir Engine oil(includes filterchange) Motorcraft SAE5W-20 SuperPremium MotorOil 3.8L engine 5.44L(5.75 quarts) Engine coolant 2 MotorcraftPremium EngineCoolant(green-colored)or MotorcraftPremium Gol...

LUBRICANT SPECIFICATIONS Item Ford partname Ford partnumber Fordspecification Brake fluid HighPerformanceDOT 3 MotorVehicle BrakeFluid 1 C6AZ-19542-AB ESA-M6C25-Aand DOT 3 Doorweatherstrips SiliconeLubricant F7AZ-19G208-BAandF5AZ-19553-AA ESR-M13P4-A Engine coolant Ford PremiumEngine Coolant(green c...

Ford Extended Service Plan You can get more protection for your new car or light truck bypurchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESPis an optional service contract which is backed by Ford Motor Companyor Ford Motor Service Company (in the U.S.) and Ford of Canada (inCanada). ...

If you have questions or concerns, or are unsatisfied with the service youare receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at yourselling/servicing dealership. 2. If your inquiry or concern remains unresolved, contact the SalesManager or Service Manager at t...

replacement or repurchase remedies provided by certain state laws. Thisdispute handling procedure is not required prior to enforcing statecreated rights or other rights which are independent of the Magnuson-Moss Warranty Act or state replacement or repurchase laws. THE DISPUTE SETTLEMENT BOARD (U.S....

Concerns are ineligible for review if the New Vehicle Limited Warrantyhas expired at receipt of your application and, in certain states eligibilityis dependent upon the customer’s possession of the vehicle. Eligibility may differ according to state law. For example, see the uniquebrochures for Calif...

• a brief summary of the action taken by the dealer(s) and Ford MotorCompany • the names (if known) of all the people you contacted at thedealership(s) • a description of the action you expect to resolve your concern You will receive a letter of explanation if your application does notqualify for Bo...

To Request a DSB Brochure/Application For a brochure/application, speak to your dealer or write/call to theBoard at the following address/phone number: Dispute Settlement BoardP.O. Box 5120Southfield, MI 48086–51201–800–428–3718 You may also contact the North American Customer Relationship Centerat ...

GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country, contact theappropriate foreign embassy or consulate. These officials can inform youof local vehicle registration regulations and where to find unleaded fuel. If you cannot find unleaded fuel or can onl...

Luggage/cargo basket Raised cross bars (roof rack) Soft luggage cover Trailer hitch (Class II) Trailer hitch bars and balls Trailer hitch mount bike carrier Trailer hitch wiring adaptor Video entertainment system Protection and appearance equipment Cargo liners, interior Carpet floor mats Cleaners, ...

For maximum vehicle performance, keep the following information inmind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to yourvehicle, do not exceed the total weight capacity of the vehicle or ofthe front or rear axle (GVWR or GAWR a...

Obtaining a French owner’s guide French Owner’s Guides can be obtained from your dealer or by writing toFord Motor Company of Canada, Limited, Service Publications, P.O. Box1580, Station B, Mississauga, Ontario L4Y 4G3. IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that,...

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle hasa defect that could cause a crash, orcould cause injury or death, youshould immediately inform theNational Highway Traffic SafetyAdministration (NHTSA) in additionto notifying Ford Motor Company. If NHTSA receives similar compl...

A Accessory delay ..........................86 AdvanceTrac ..............................170 Air bag supplementalrestraint system ........144–145, 149 and child safety seats ............146description ......................145, 149disposal ....................................151driver air bag .........

Load limits .................................178 GAWR ......................................178GVWR ......................................178trailer towing ..........................178 Locks autolock ...................................110childproof ..................................88 Lubricant spe...

W Warning chimes .....................13–14 Warning lights (see Lights) .........8 Washer fluid ..............................215 Water, Driving through .............178 Windows power .........................................85rear wiper/washer .....................83 Windshield washer fluid andwipe...

Item Information Required fuel Unleaded fuel only - 87 octane Fuel tank capacity 98.4L (26.0 gallons) Engine oil capacity-3.8L engine(includes filter change) 5.44L (5.75 quarts). UseMotorcraft SAE 5W-20Super Premium Motor Oil, Fordspecification WSS-M2C153-H. Tire size and pressure Refer to the Certi...