Ford 2001 Ranger- Manuals

Using your vehicle as an ambulance Do not use this vehicle as an ambulance. Your vehicle is not equipped with the Ford Ambulance PreparationPackage. Electric vehicles For information on operating your Electric Vehicle, also refer to theElectric Vehicle Owner’s Guide Supplement. Introduction 5

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat InstallationWarning Child Seat TetherAnchorage Brake System Anti-Lock Brake System Brake Fluid -Non-Petroleum Based Tr...

C 0 1 2 3 4 5 6 RPMx1000 ABS ! BRAKE CHECKENGINE CHECK FUEL CAP E F H H H P R N D 2 1 THEFT SPEEDCONT 4WDHIGH 4WDLOW O/DOFF L L 10 MPH 20 50 60 70 30 40 80 90 km/h 0 0 0 10 1 00 1 20 1 0 0 0 0 0 0 40 60 80 100 120 140 160 180 20 DOORAJAR CHECK GAGE DIM OFF SET ACC COAST OFF ON Headlamp control (pg. ...

WARNING LIGHTS AND CHIMES Check engine Your vehicle is equipped with acomputer that monitors the engine’semission control system. Thissystem is commonly known as theOn Board Diagnostics System (OBDII). This OBD II system protects the environment by ensuring that yourvehicle continues to meet governm...

Check gage Illuminates when the engine coolanttemperature is high, the engine oilpressure is low or the fuel gauge isat or near empty. The ignition mustbe in the ON position for this lamp to illuminate. The lamp will also stayilluminated after the ignition is turned to the ON position. Refer to Engi...

Anti-lock brake system (ABS) Momentarily illuminates when theignition is turned to the ON positionto indicate a system check. If thelight remains on, continues to flashor fails to illuminate, have thesystem serviced immediately. With the ABS light on, the anti-lock brakesystem is disabled and normal...

O/D off (if equipped) Illuminates when the TransmissionControl Switch (TCS), refer to Overdrive control in the Controls and Features chapter, has been pushed turning the transmission overdrive function OFF. When the lightis on, the transmission does not operate in the overdrive mode, refer tothe Dri...

Speed control This light comes on when either theSET/ACCEL or RESUME controlsare pressed. It turns off when thespeed control OFF control ispressed, the brake or clutch (if equipped) is applied or the ignition isturned to the OFF position. Safety belt warning chime Sounds to remind you to fasten your...

Engine coolant temperature gauge Indicates the temperature of theengine coolant. At normal operatingtemperature, the needle remainswithin the normal area (the areabetween the “H” and “C”). If it enters the red section, theengine is overheating. Stop thevehicle as soon as safelypossible, switch off t...

Speedometer Indicates the current vehicle speed. Odometer Registers the total kilometers(miles) of the vehicle. Trip odometer Registers the kilometers (miles) ofindividual journeys. To reset,depress the control. 10 MPH 20 50 60 70 30 40 80 90 km/h 0 0 0 10 1 00 1 20 1 0 0 0 0 0 0 40 60 80 100 120 14...

Engine oil pressure gauge This shows the engine oil pressurein the system. Sufficient pressureexists as long as the needle remainsin the normal range (the areabetween the “L” and “H”). If the gauge indicates low pressure,stop the vehicle as soon as safelypossible and switch off the engineimmediately...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parkinglamps. Rotate to the second positionto also turn on the headlamps. Foglamp control (if equipped) The foglamps can be turned onwhen the headlamp control is ineither of the following positions: • Parking lamps • Lo...

High beams • Push forward to activate. • Pull toward you to deactivate. Flash to pass Pull toward you to activate andrelease to deactivate. PANEL DIMMER CONTROL Use to adjust the brightness of theinstrument panel during headlampand parklamp operation. • Rotate up to brighten. • Rotate down to dim. •...

CLIMATE CONTROL SYSTEM Heater only system (if equipped) Fan speed control Controls the volume of air circulatedin the vehicle. Temperature control knob Controls the temperature of theairflow inside the vehicle. Onheater-only systems, the air cannotbe cooled below the outsidetemperature. Mode selecto...

Operating tips • In humid weather conditions, place the climate control system inDEF before driving. This will reduce fogging on your windshield. Oncethe windshield has been cleared, operate the climate control system asdesired. • To reduce humidity buildup inside the vehicle in cold weatherconditio...

Manual heating and air conditioning system (if equipped) Fan speed control Controls the volume of air circulatedin the vehicle. Temperature control knob Controls the temperature of theairflow inside the vehicle. Mode selector control Controls the direction of the airflowto the inside of the vehicle....

AUXILIARY POWER POINT Power outlets are designed for accessory plugs only. Do not hangany type of accessory or accessory bracket from the plug.Improper use of the power outlet can cause damage not coveredby your warranty. The auxiliary power point is located on the instrument panel. This outletshoul...

PASSENGER AIR BAG ON/OFF SWITCH This switch must be used todeactivate the passenger air bagwhenever a child seat is used in theright front or center front passengerseat position. Refer to Passenger air bag ON/OFF switch in the Seating and safety restraints chapter. USING YOUR AUDIO SYSTEM AM/FM Ster...

Volume/power control Press the control to turn the audiosystem on or off. Turn the control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition switch is turned back on. AM/FM s...

Tune adjust in radio mode • Press to move to the next frequency down the band(whether or not a listenablestation is located there). Hold thecontrol to move through thefrequencies quickly. • Press to move to the next frequency up the band (whether or not a listenable station is located there). Hold f...

Bass adjust The bass adjust control allows youto increase or decrease the audiosystem’s bass output. Press the TONE control once, thenuse the volume knob to adjust thedesired level. Treble adjust The treble adjust control allows youto increase or decrease the audiosystem’s treble output. Press the T...

AM/FM select The AM/FM select control works inradio and CD modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press thecontrol to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in CD mode Press this control to stop CD play and begin radi...

Tune adjust for CD changer (if equipped) • Press to select the previous disc in the CD changer. (Play willbegin on the first track of thedisc unless the CD changer is inshuffle mode. Refer to Shuffle feature for more information. Hold the control to continue reversing through the disc. • Press to se...

Scan function in radio mode Press SCN to hear a brief sampling of all listenable stations on thefrequency band. Press SCN again to stop the scan mode. Scan function in CD mode Press SCN to hear a short sampling of all selections on the CD. (The CDscans in a forward direction, wrapping back to the fi...

Speaker fade adjust Speaker sound can be adjustedbetween the front and rearspeakers. CD select • To begin CD play (if CD[s] areloaded), press the CD control.The first track of the disc willbegin playing. After that, CD playwill begin where it stopped last. Do not insert any promotional (odd shaped o...

Eject function Press the control to stop and ejecta CD. Compression feature Compression adjust brings soft andloud CD passages together for amore consistent listening level. Press the COMP control to activate and deactivate compression adjust. Shuffle feature (if equipped with CD changer) The shuffl...

To set the minute, press and holdthe CLK control and press theTUNE control: • to decrease minutes and • to increase minutes. Premium AM/FM Stereo/Cassette/Single CD SEEK DISCS TUNE SEEK TUNE SEEK TUNE FM 1AMC BL RF REW FF SCAN BASS TREB SEL BAL TAPE DISC EJ CD FADE AUTO CLK SIDE 1-2 COMP SHUFFLE EJ ...

Volume/power control Press the control to turn the audiosystem on or off. Audio power can also be turned onby pressing the AM/FM selectcontrol or the tape/CD selectcontrol. Audio power is turned offby using the volume/power control. Turn control to raise or lowervolume. If the volume is set above a ...

Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. 3. When the first six strong stationsare filled, the station stored inmemory preset control 1 will startplaying. If there are less than six strongstations available on the frequencyband, ...

Tape select • To begin tape play (with a tapeloaded into the audio system)while in the radio or CD mode,press the TAPE control. Press thebutton during rewind or fast forward to stop the rewind or fastforward function. Rewind The rewind control works in tapeand CD modes. • In tape mode, radio play wi...

Press the EJ control to stop andeject a CD. Dolby T noise reduction Dolby t noise reduction operates in tape mode. Dolby t noise reduction reduces the amount of hiss andstatic during tape playback. Press the control to activate (and deactivate) the Dolby t noise reduction. Dolby t noise reduction is...

Setting the clock To set the hour, press and hold theCLK control and press SEEK: • to decrease hours and • to increase hours. To set the minute, press and holdthe CLK control and press TUNE: • to decrease minutes and • to increase minutes. If your vehicle has a separate clock,(other than the digital...

The CLK control will allow you toswitch between media display mode(radio station, stereo information,etc.) and clock display mode (time).When in clock mode, the mediainformation will display for 10seconds, when the radio is turnedon, and then revert to clockinformation. Any time that themedia is cha...

Volume/power control Press the control to turn the audiosystem on or off. Turn the control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition switch is turned back on. AM/FM s...

Tune adjust in radio mode • Press to move to the next frequency down the band(whether or not a listenablestation is located there). Hold thecontrol to move through thefrequencies quickly. • Press to move to the next frequency up the band (whether or not a listenable station is located there). Hold f...

Menu mode The MENU control allows you toaccess many different featureswithin your audio system. There arethree sets of menus availabledepending upon which mode orfeature is activated. While in FM mode, two menus areavailable. If RDS is turned OFF , you can access the following: • SELECT HOURS — Refe...

Radio data system (RDS) feature This feature allows your audiosystem to receive text informationfrom RDS-equipped FM radiostations. To activate RDS: • When in FM mode, press the MENU control until RDS OFF displays. • Press the SEL control to engage this feature (RDS ON). RDS features: Once the RDS f...

Mute mode Press the control to mute theplaying media. Press the controlagain to return to the playing media. Setting the clock Press the MENU control untilSELECT HOUR or SELECTMINUTE is displayed. (The menumode must be engaged to enableclock mode). Use the SEL control to manually setthe time. • Pres...

Radio frequency information The Federal Communications Commission (FCC) and the Canadian Radioand Telecommunications Commission(CRTC) establish the frequenciesAM and FM stations may use for their broadcasts. Allowable frequenciesare: AM 530, 540–1600, 1610 kHz FM 87.7, 87.9–107.7, 107.9 MHz Not all ...

To turn speed control off • Press OFF or • Turn off the vehicle ignition. Once speed control is switched off,the previously programmed setspeed will be erased. To set a speed • Press SET ACC. For speedcontrol to operate, the speedcontrol must be ON and thevehicle speed must be greaterthan 48 km/h (3...

To disengage speed control • Depress the brake pedal or • Depress the clutch pedal (ifequipped). Disengaging the speed control willnot erase the previouslyprogrammed set speed. Fullydepressing the clutch pedal maycause a flare in engine RPM as thethrottle is returned to idle. This isnormal. Pressing...

To return to a previously set speed • Press RSM. For RSM to operate,the vehicle speed must be fasterthan 48 km/h (30 mph). Indicator light This light comes on when either theSET ACCEL or RES controls arepressed. It turns off when the speedcontrol OFF control is pressed, thebrake or clutch is applied...

HAZARD FLASHER For information on the hazard flasher control, refer to Hazard flasher in the Roadside emergencies chapter. WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper controlto the desired interval, low or highspeed position. The bars of varying length are forintermittent wipers. Wh...

POWER WINDOWS (IF EQUIPPED) Press and hold the rocker switches to open and close windows. • Press the top portion of therocker switch to close. • Press the bottom portion of therocker switch to open. One touch down • Press AUTO completely down andrelease quickly. The driver’swindow will open fully. ...

CARGO AREA FEATURES Cargo area shade (if equipped) Your vehicle may be equipped with notches in the side trim panels thatare used for a cargo area shade. See your dealer for more information. BED EXTENDER (IF EQUIPPED) Your vehicle may be equipped with a bed extender designed to extendthe pickup box...

To stow the rear panel: • Before driving with the tonneaucover open, stow the rear panel. • Release four cylinder clips andremove two hydraulic cylindersfrom the pickup box and rearpanel. • Lift the rear panel up, lay it ontop of the front panel and secureit with the two straps on thefront panel tie...

To remove the tonneau cover: The tonneau cover needs to besupported during removal. This is atwo person operation. • Remove the cargo divider, referto To remove the cargo divider in this procedure. • Open and support the frontpanel. • Release four cylinder clips andremove the two hydrauliccylinders ...

The remote entry features only operate with the ignition in the LOCKposition. If there is any potential remote keyless entry problem with your vehicle,ensure ALL key fobs (remote entry transmitters) are brought to the dealership, to aid in troubleshooting. Unlocking the doors Press this control to u...

Sounding a panic alarm Press this control to activate thealarm. To deactivate the alarm, press thecontrol again or turn the ignition toACC or ON. Panic alarm will only operate withthe ignition in the OFF position. Replacing the battery The transmitter is powered by one coin type three-volt lithium b...

Replacing lost transmitters If a remote transmitter has been lostand you would like to remove itfrom the vehicle’s memory, or youwould like to purchase additionalremote transmitters and have themprogrammed to your vehicle: • Take all your vehicle’s transmitters to your dealer forprogramming, or • Pe...

Illuminated entry The interior lamps illuminate when the remote entry system is used tounlock the door(s) or sound the personal alarm. The system automatically turns off after 25 seconds or when the ignitionis turned to the RUN or ACC position. The dome lamp control (ifequipped) must not be set to t...

Key information Your vehicle is supplied with two coded keys. Only a coded key will start your vehicle. Spare coded keyscan be purchased from yourdealership. Your dealership canprogram your key or you can “do ityourself”, refer to Programming spare keys. Large metallic objects, electronicdevices on ...

Pull lever up to adjust seatback. Using the manual lumbar support (if equipped) Turn the lumbar support controlclockwise to increase firmness. Turn the lumbar support controlcounterclockwise to increasesoftness. REAR SEATS Center facing jump seat (2 door SuperCab) (if equipped) To open, pull inboard...

Center facing jump seat (4 door SuperCab) (if equipped) To open, pull seat assembly down,then raise seatback. To stow the seat, fold seat backdown and raise seat assembly to thefully upright position. Do not install a child seat ina center facing jump seat. SAFETY RESTRAINTS Safety restraints precau...

In a rollover crash, an unbelted person is significantly more likelyto die than a person wearing a safety belt. Each seating position in your vehicle has a specific safety beltassembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on t...

The automatic locking mode is not available on the driver safety belt. When to use the automatic locking mode • Any time a child safety seat is installed in a passenger front or outboard rear seating position (if equipped). Children 12 years old andunder should be properly restrained in the rear sea...

How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retractcompletely to disengage the automatic locking mode and activate thevehicle sensitive (emergency) locking mode. After any vehicle collision, the front passenger outboard seat beltsystem mus...

Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and frontpassenger. Adjust the height of the shoulder belt so the belt rests acrossthe middle of your shoulder. • Regular Cab and 4–door SuperCab • 2–door SuperCab To lower the shoulder belt height, pu...

Position the shoulder belt height adjusters so that the belt restsacross the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt andincrease the risk of injury in a collision. Lap belts Adjusting the front center seat lap belt (if equip...

Adjusting the rear center facing jump seat lap belt (if equipped) The lap belt will adjust automatically. To fasten, grasp the tongue, andwith a continuous motion, pull out enough webbing to buckle the tongueinto the correct buckle. If you did not pull out enough webbing to reachthe buckle, allow th...

If... Then... The driver’s safety belt is buckledbefore the ignition switch is turnedto the ON position... The safety belt warning light andindicator chime remain off. Belt minder The Belt Minder feature is a supplemental warning to the safety beltwarning function. This feature provides additional r...

Reasons given... Consider... “Belts areuncomfortable” We design our safety belts to enhance comfort. Ifyou are uncomfortable - try different positions forthe safety belt upper anchorage and seatbackwhich should be as upright as possible; this canimprove comfort. “I was in a hurry” Prime time for an ...

Deactivating/activating the belt minder feature Read steps 1 - 9 thoroughly before proceeding with thedeactivation/activation programming procedure. The Belt Minder feature can be deactivated/activated by performing thefollowing procedure: Before following the procedure, make sure that: • The parkin...

• This will disable Belt Minder if it is currently enabled, or enable BeltMinder if it is currently disabled. 7. Confirmation of disabling Belt Minder is provided by the safety beltwarning light flashing four times per second for three seconds.8. Confirmation of enabling Belt Minder is provided by: ...

The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion ...

• and the electrical wiring which connects the components. The RCM (restraints control module) monitors its own internal circuitsand the supplemental air bag electrical system warning (including thepassenger air bag deactivation switch, the impact sensors, the systemwiring, the air bag system readin...

Passenger air bag ON/OFF switch An air bag ON/OFF switchhas been installed in this vehicle. Before driving, always look at the face of the switch tobe sure the switch is in the properposition in accordance with theseinstructions and warnings. Failureto put the switch in a properposition can increase...

Turning the passenger air bag back on The passenger air bag remains OFF until you turn it back ON. 1. Insert the ignition key and turnthe switch to ON. 2. The OFF light will brieflyilluminate when the ignition isturned to ON. This indicates thatthe passenger air bag is operational. If the OFF light ...

The vast majority of drivers and passengers are much safer with an airbag than without. To do their job and reduce the risk of life threateninginjuries, air bags must open with great force, and this force can pose apotentially deadly risk in some situations, particularly when a front seatoccupant is...

3. Medical condition. A passenger has a medical condition which, according to his or her physician: • causes the passenger air bag to pose a special risk for the passenger;and • makes the potential harm from the passenger air bag in a crashgreater than the potential harm from turning OFF the air bag...

• the child has a medical condition that, according to the child’sphysician, makes it necessary for the child to ride in the front seat sothat the driver can monitor the child’s condition. 3. Medical condition: A passenger has a medical condition that, according to his or her physician: • poses a sp...

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant orchild restraint you might use.When possible, always place children under age 12 ...

SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all of the manufacturer’s instructions with thesafety seat you put in your vehicle. If you do not install and use thesafety seat properly, the ...

Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap whichgoes over the back of the seat and hooks to an anchoring point. Tetherstraps are available as an accessory for many older safety seats. Contactthe manufacturer of your child seat fo...

3. Locate the correct anchor for the selected seating position. The tether anchor is located on therear lower portion of the passengerseat. Seating and safety restraints 119

Center seating location When installing a child safety seat in the center position, route the tetherstrap over the center arm rest and clip it to the center anchor. Seating and safety restraints 121

Center seating location 60/40 vinyl seats When installing a child safety seat in the center position on a 60/40 vinylseat, route the tether strap through the guiding sleeve and clip it to thecenter anchor. If the tether strap is clipped incorrectly, the child safety seatmay not be retained properly ...

PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. Thissystem meets all Canadian Interference-Causing Equipment standardrequirements regulating the impulse electrical field strength of radionoise. When starting a fuel-injected engine, avoid pressing the a...

Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate. Cold weather starting (flexible fuel vehicles only) As the outside temperature approaches freezing, ...

If the engine fails to start using the preceding instructions 1. Press the accelerator pedal 1/3 to 1/2 of the way to floor and hold. 2. Turn the key to START position. 3. When the engine starts, release the key, then release the acceleratorpedal gradually as the engine speeds up. 4. If the engine s...

BRAKES Your service brakes are self-adjusting. Refer to the scheduledmaintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate aperformance concern with the vehicle’s brake system. In normaloperation, automotive brake systems may emit occasional or int...

steering control of your vehicle and, providing there is sufficientspace, will enable you to avoid obstacles and bring the vehicle to acontrolled stop. • The anti-lock system does not decrease the time necessary to applythe brakes or always reduce stopping distance. Always leave enoughroom between y...

The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released. Always set the parking brake fully and make sure that thegearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual t...

Your vehicle has the capability to haul more cargo and people than mostpassenger cars. Depending upon the type and placement of the load,hauling people and cargo may raise the center of gravity of the vehicle. Use extra caution while becoming familiar with your vehicle. Know thecapabilities and limi...

If the parking brake is fully released, but the brake warning lampremains illuminated, the brakes may not be working properly. See your dealer or a qualified service technician. Driving with a 5–speed automatic transmission (if equipped) Your automatic transmission electronically controls the shift ...

Drive – Not shown on the display. Activate by pressing the transmission control switch on the end of the gearshift lever with the gearshift inthe (Overdrive) position. The TCIL will illuminate on the instrument cluster. Transmission operates in gears one through four. Drive (O/DOFF) provides more en...

Manual transmission operation (if equipped) Using the clutch Vehicles equipped with a manualtransmission have a starter interlockthat prevents starting the engineunless the clutch pedal is fullydepressed. When starting a vehicle with amanual transmission: 1. Hold down the brake pedal. 2. Depress the...

2. Engage the parking brake. 3. Shift into 1 (First). 4. Turn the ignition to Off. Do not park your vehicle in Neutral, it may move unexpectedlyand injure someone. Use 1 (First) gear and set the parking brake fully. Recommended shift speeds Upshifts when accelerating (for best fuel economy) Shift fr...

Upshifts when accelerating (for best fuel economy) Maximum downshift speeds Shift from: Transfer case position (if equipped) 4H 4L 5 (Overdrive) - 4 88 km/h (55 mph) 34 km/h (22 mph) 4 - 3 72 km/h (45 mph) 27 km/h (18 mph) 3 - 2 56 km/h (35 mph) 21 km/h (14 mph) 2 - 1 32 km/h (20 mph) 11 km/h (8 mph...

4WD system indicator lights The 4WD system indicator lights illuminate only under the followingconditions. If these lights illuminate when driving in 2WD, contact yourFord dealer as soon as possible. • 4WD HIGH -momentarily illuminates when the vehicle isstarted. Illuminates when 4H(4WD High) is eng...

Shifting from 4X4 HIGH (4WD high) to 2WD (2WD high) Move the 4WD control to 2WDposition at any forward speed. • You do not need to operate the vehicle in R (Reverse) todisengage your front hubs. Shifting from 2WD (2WD high) to 4X4 LOW (4WD low) 1. Bring the vehicle to a stop. 2. Depress the brake. 3...

4. Move the 4WD control to the2WD position. Shifting between 4X4 HIGH (4WD high) and 4X4 LOW (4WD low) 1. Bring the vehicle to a stop. 2. Depress the brake. 3. Place the gearshift in N (Neutral) (automatic transmission) or depressthe clutch (manual transmission). 4. Move the 4WD control to the 4X4HI...

TRACTION-LOK AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly whenone wheel is on a poor traction surface. Under normal conditions, theTraction-Lok axle functions like a standard rear axle. Extended use of other than the manufacturer’s specified size tires on a...

The Safety Certification Label, found on the driver’s door pillar, listsseveral important vehicle weight rating limitations. Before adding anyadditional equipment, refer to these limitations. If you are adding weightto the front of your vehicle, (potentially including weight added to thecab), the we...

3. Subtract your loaded vehicle weight from the maximum GCWR on thefollowing charts. This is the maximum trailer weight your vehicle can towand must fall below the maximum shown under maximum trailer weighton the chart. TRAILER TOWING Your vehicle may tow a class I, II or III trailer provided the ma...

4x2 w/manual transmission Regular Cab w/7’ box 2.3L All 2 177 (4 800) 726 (1 600) Equal to frontal area of vehicle 3.0L All 2 722 (6 000) 1 179 (2 600) 4.64 (50) 4.0L All 3 175 (7 000) 1 597 (3 520) 4.64 (50) SuperCab 2.3L All 2 177 (4 800) 671 (1 480) Equal to frontal area of vehicle 3.0L (non-tors...

Preparing to tow Use the proper equipment for towing a trailer, and make sure it isproperly attached to your vehicle. See your dealer or a reliable trailerdealer if you require assistance. Hitches For towing trailers up to 907 kg (2 000 lb), use a weight carrying hitchand ball which uniformly distri...

Refer to the following chart for information regarding thefactory-equipped trailer tow connector: Trailer tow connector Color Function Comment 1. Dark Green Trailer right-handturn signal Circuit activated when brakepedal is depressed or whenignition is on and right-handturn signal is applied. 2. Yel...

Trailer towing tips • Practice turning, stopping and backing up before starting on a trip toget the feel of the vehicle trailer combination. When turning, makewider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached. • The tra...

4x2 and 4x4 vehicles equipped with manual transmissions Before you have your vehicle towed: • Release the parking brake. • Move the gearshift to N (Neutral). • Turn the key in the ignition to the OFF/UNLOCKED position. • The maximum recommended speed is 88 km/h (55 mph). • The maximum recommended di...

Getting roadside assistance To fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program. Thisprogram is separate from the New Vehicle Limited Warranty. The serviceis available: • 24–hours, seven days a week • for the Basic warranty peri...

FUSES AND RELAYS Fuses If electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check the appropriatefuses before replacing any electricalcomponents. NOTE: Always replace a fuse with one that has the specified amperage r...

Passenger compartment fuse panel The fuse panel is located on theleft-hand side of the instrumentpanel facing the driver’s side door.Pull the panel cover outward toaccess the fuses. To remove a fuse use the fuse puller tool provided on the fuse panelcover. 1 234 5 678 9 1 01 11 2 13 14 15 16 17 18 1...

Power distribution box The power distribution box islocated in the engine compartment.The power distribution box containshigh-current fuses that protect yourvehicle’s main electrical systemsfrom overloads. Always disconnect the battery before servicing high currentfuses. Always replace the cover to ...

It is not recommended that the vehicle be operated in 4WD modes witha temporary spare. If 4WD operation is necessary, do not operate abovespeeds of 16 km/h (10 mph) or for distances above 80 km (50 miles). If you use the temporary spare tire continuously or do not followthese precautions, the tire c...

Location of the spare tire and tools The spare tire and tools for your vehicle are stowed in the followinglocations: Tool Location Spare tire Under the vehicle, just forward of the rearbumper Jack, jack handle, wheel nut wrench Regular Cab: behind seats and underneath thejack and tools cover SuperCa...

2. If equipped, unlock and removethe spare tire carrier lock from therear access hole located just abovethe rear bumper and below thetailgate. 3. Insert the straight end of the jackhandle into the rear access holelocated just above the rear bumperand below the tailgate. Forward motion will stop andr...

Stowing the spare tire 1. Lay the tire on the ground with the valve stem facing up. 2. Install the retainer through thewheel center and slide the wheelunder the vehicle. 3. Turn the spare handle clockwiseuntil the tire is raised to its originalposition underneath the vehicle. Thespare handle ratchet...

3. Block the diagonally oppositewheel. 4. Insert tapered end of the lugwrench behind hub caps and twistthem off. 5. Loosen each wheel lug nutone-half turn counterclockwise butdo not remove them until the wheelis raised off the ground. 6. Position the jack according to thefollowing guides and turn th...

10. Remove the jack and fullytighten the lug nuts in the ordershown. 11. Stow the flat tire. Refer to Stowing the spare tire. 12. Stow the jack and lug wrench.Make sure the jack is fastened so itdoes not rattle when you drive. 13. Unblock the wheels. JUMP STARTING YOUR VEHICLE The gases around the b...

4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect any electricalsurges. Turn all other accessories off. Connecting the jumper cables 1. Connect the po...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingbelt. Ford Motor Company has notapproved a ...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a scheduled maintenance guide which makes trackingroutine service easy. If your vehicle requires professional service, your dealership can providethe...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.3L I4 engine 1. Windshield washer fluid reservoir 2. Engine coolant reservoir 3. Engine oil dipstick 4. Transmission fluid dipstick (automatic transmission) 5. Engine oil filler cap 6. Brake fluid reservoir 7. Power distribution box 8. Clutch fluid ...

ENGINE OIL Checking the engine oil Refer to the scheduled maintenance guide for the appropriate intervalsfor checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into theoil pan. 3. Set the parking brake and ensure t...

6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil level is between the MIN and MAX marks, the oil level is acceptable, DO NOT ADD OIL. • If the oil level is below the MIN mark, add enough oil to raise the levelwithin the MIN-MAX range. • 2.3L I4 engine • 3.0L...

• 4.0L SOHC V6 engine • Oil levels above the MAX mark may cause engine damage. Some oilmust be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in...

Engine Oil Recommendations 2.3L & 3.0L Engines Look for this certificationtrademark. SAE 5W-20 engine oil is recommended. Only use oils “Certified For Gasoline Engines” by the AmericanPetroleum Institute (API). Use Motorcraft (Part: XO–5W20–QSP inU.S.)or an equivalent oil meeting Ford Specificat...

1. Clean the reservoir cap beforeremoval to prevent dirt and waterfrom entering the reservoir. 2. Remove cap and rubberdiaphragm from reservoir. 3. Add fluid until the level reachesthe step in the reservoir. 4. Reinstall rubber diaphragm andcap onto reservoir. WINDSHIELD WASHER FLUID Washer fluid Ch...

Note: Do not put washer fluid in the engine coolant reservoir. Washer fluid placed in the cooling system may harm engine and cooling systemcomponents. ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at themileage intervals listed in the schedule...

• 3.0L and 4.0L engines When the engine is cold, check the level of the engine coolant in thereservoir. • The engine coolant should be at the “cold fill level” or within the “coldfill range” as listed on the engine coolant reservoir (depending uponapplication). • Refer to the Scheduled Maintenance G...

Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn you badly. Also, you can be burned if you spill coolant on hot engine parts. Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine...

If you have to add more than 1.0 liter (1.0 quart) of engine coolant permonth, have your dealer check the engine cooling system. Your coolingsystem may have a leak. Operating an engine with a low level of coolantcan result in engine overheating and possible engine damage. Recycled engine coolant For...

If you drive in extremely hot climates: • It is still necessary to maintain the coolant concentrationabove 40%. • NEVER decrease the coolant concentration below 40%. • Decreased engine coolant concentrations below 40% willdecrease the corrosion protection characteristics of the enginecoolant and may...

3. Turn the engine off. 4. If your vehicle is equipped with a 3.0L V6 engine, check the fluid level on the dipstick. It should be within the FULL HOT range. Do notadd fluid if the level is within this range. 5. If your vehicle is equipped with a 4.0L SOHC V6 or 2.3L I4 engine, check the fluid level ...

7. Remove the dipstick and inspect the fluid level. The fluid should be inthe designated area for normal operating temperature or ambienttemperature. Low fluid level Do not drive the vehicle if the fluidlevel is at the bottom of the dipstickand the ambient temperature isabove 10°C (50°F). Correct fl...

Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used. The type offluid used is normally indicated on the dipstick and also in the Lubricant specifications section in the Capacities and specifications chapter. Use of a non-approved automatic transm...

3. Fluid level should be at bottom ofthe opening. 4. Add enough fluid through thefiller opening so that the fluid levelis at the bottom of the opening. 5. Install and tighten the fill plugsecurely. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter. Che...

If you see any corrosion on the battery or terminals, remove the cablesfrom the terminals and clean with a wire brush. You can neutralize theacid with a solution of baking soda and water. Batteries normally produce explosive gases which can causepersonal injury. Therefore, do not allow flames, spark...

6. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven to relearn the idle and fuel trimstrategy. • If you do not allow the engine to relearn its idle trim, the idlequality of your vehicle may be adversely affected until the idletrim is eventually relearned. Whe...

Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from thewindshield and lock into the serviceposition. 2. Turn the blade at an angle fromthe wiper arm. Push the lock pinmanually to release the blade andpull the wiper blade down towardthe windshield to remove it from ...

SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has beenparked for at least one hour or has been driven less than 5 km(3 miles). • Adjust tire pressure to recommended specifications found on theCe...

• Five tire rotation Replacing the tires Replace the tires when the wearband is visible through the tiretreads. When replacing full size tires, never mix radial bias-belted, orbias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same s...

Do not replace your tires with “high performance” tires or largersize tires. Failure to follow these precautions may adversely affect thehandling of the vehicle and make it easier for the driver to lose control and roll over. Tires that are larger or smaller than your vehicle’s original tires may al...

Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materialsand any open flames beforefueling your vehicle. • Always turn off the vehicle beforefueling. • Automotive fuels can be harmfulor fatal if swallowed. Fuels suchas gasoline and ethanol are highlytoxic and...

Use the following guidelines to avoid static build-up when filling anungrounded fuel container: • Place approved fuel container on the ground. • DO NOT fill a fuel container while it is in the vehicle (including thecargo area). • Keep the fuel pump nozzle in contact with the fuel container whilefill...

Standards for fuel ethanol have been developed to provide FFVs the bestpossible performance, safety and durability. To assist alcohol fuelproviders in meeting these standards, guidelines have also beendeveloped which prescribe “Ethanol Fuel Compatible” dispensing stationequipment. These standards an...

Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in kilometers or miles). 2. Each time you fill the tank, record the amount of fuel added (in litersor gallons). 3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current od...

• Driving at reasonable speeds (traveling at 88 km/h [55 mph] uses 15%less fuel than traveling at 105 km/h [65 mph]). • Revving the engine before turning it off may reduce fuel economy. • Using the air conditioner or defroster may reduce fuel economy. • You may want to turn off the speed control in ...

• Transmissions give their best fuel economy when operated in the topcruise gear and with steady pressure on the gas pedal. • Four-wheel-drive operation (if equipped) is less fuel efficient thantwo-wheel-drive operation. • Close windows for high speed driving. EPA window sticker Every new vehicle sh...

5. Remove the bulb retaining ring byrotating it counterclockwise (whenviewed from the rear) to free itfrom the bulb socket, and slide thering off the plastic base. Keep thering to retain the new bulb. 6. Without turning, remove the oldbulb by gently pulling it straightback out of the lamp assembly. ...

Replacing front side marker bulbs 1. Open the hood. 2. Remove two screws and cover (ifequipped). 3. At the back of the headlamp, pryup the two retainer pins to releasethe headlamp assembly from thevehicle and pull headlamp forward. 4. Remove screw(s) from lampassembly. 5. Disengage lamp assembly (it...

6. Rotate bulb socketcounterclockwise and remove fromlamp assembly. 7. Carefully pull bulb straight out ofsocket and push in the new bulb. 8. Install the bulb socket in lampassembly by turning clockwise. 9. Align the lamp on the vehicle andpush to snap in place. 10. Install screw(s) on lamp assembly...

3. Rotate bulb socketcounterclockwise turn and removefrom lamp assembly. 4. Carefully pull the bulb straightout of the socket and push in thenew bulb. 5. Install the bulb socket in lampassembly by turning clockwise. 6. Install the lamp assembly andsecure with four screws. Replacing foglamp bulbs 1. ...

To remove the brakelamp assembly: 1. Remove the two screws and lampassembly from vehicle. 2. Remove the bulb socket fromlamp assembly by rotating itcounterclockwise. 3. Carefully pull bulb straight out ofsocket and push in the new bulb. To install the brakelamp assembly: 1. Install the bulb socket i...

CLEANING AND CARING FOR YOUR VEHICLE Refer to the Customer Assistance chapter for a list of Ford-approvedcleaners, polishes and waxes. Washing your vehicle Wash your vehicle regularly withcold or lukewarm water. Never usestrong detergents or soap. If yourvehicle is particularly dirty, use aquality c...

Use only carnauba or synthetic-based waxes. Use a cleaning fluid with aclean cloth to remove any bugs before waxing your vehicle. Use tarremover to remove any tar spots. Avoid getting wax on the windshield, or on any surfaces which appearcoarse or bumpy. If you have wax applied at a commercial car w...

Cleaning the engine Engines are more efficient when they are clean because grease and dirtbuildup keep the engine warmer than normal. When washing: • Take care when using a power washer to clean the engine. The highpressure fluid could penetrate the sealed parts and cause damage. • Do not spray with...

• 3.0L • 4.0L • Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage. Cleaning non-painted plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover ifnecessary. Do not clean plastic parts with thinners, solvents orpet...

Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. Ifnecessary, use a tar remover such as Ford Extra Strength Tar and RoadOil Remover (B7A-19520–AA). To avoid scratching the lamps, do not use a dry paper towel, chemicalsolvents or abrasive cleaners. Cleaning th...

Cleaning the interior fabric Remove dust and loose dirt with a whisk broom or a vacuum cleaner.Remove fresh spots immediately. Do not use household or glass cleaners.These agents can stain and discolor the fabric. Use a mild soap andwater solution if necessary. Cleaning and maintaining the safety be...

MOTORCRAFT PART NUMBERS Component 2.3L I4 engine 3.0L V6 engine 4.0L V6 engine Air filterelement FA-1658 FA-1658 FA-1658 Fuel filter FG–1002 FG–1002 FG–1002 Battery BXT-59 BXT-59 BXT-59 Oil filter FL-400S FL-400S FL-820S PCV valve EV-227 EV-130 EV-225 Spark plugs* AWSF-32FEM** AWSF-32PP*** AGSF-34FP...

4 Add the coolant type originally equipped in your vehicle. 5 Traction-Lok axles use 2.2–2.4L (4.75–5.0 pints) of rear axle lubricant. Add 118 ml (4 oz.) of Additive Friction Modifier C8AZ-19B546-A orequivalent meeting Ford specification EST-M2C118–A for complete refillof Traction-Lok axles. Service...

Item Ford partname orequivalent Ford partnumber Fordspecification Engine oil 2.3L and 3.0Lengines Motorcraft SAE5W-20 SuperPremium MotorOil XO-5W20-QSP WSS-M2C153-Hand APICertificationMark 4.0L engines Motorcraft SAE5W-30 SuperPremium MotorOil XO-5W30-QSP WSS-M2C153-Gand APICertificationMark Hinges,...

VEHICLE DIMENSIONS Vehicledimensions Regular CabShort WheelBase (SWB) mm(in) Regular CabLong WheelBase (LWB)mm (in) Supercab mm(in) (1) Overalllength 4 763 (187.5) 5 093 (200.5) 5 153 (202.9) (2) Overallwidth 1 785 (70.3) 1 785 (70.3) 1 785 (70.3) (3) Overallheight 4x2/4x4 1 575 (62.0) /1 655 (65.2)...

Ford Extended Service Plan You can get more protection for your new car or light truck bypurchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESPis an optional service contract which is backed by Ford Motor Companyor Ford Motor Service Company (in the U.S.) and Ford of Canada (inCanada). ...

If you have questions or concerns, or are unsatisfied with the service youare receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at yourselling/servicing dealership. 2. If your inquiry or concern remains unresolved, contact the SalesManager or Service Manager at t...

THE DISPUTE SETTLEMENT BOARD (U.S. only) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes • available free to owners and lessees of qualifying Ford Motor Companyvehicles The Dispute Settlement Board may not be available in all states. FordMotor...

Board membership The Board consists of: • three consumer representatives • a Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained byan independent consulting firm. The dealership Board member is chosenfrom Ford and Lincoln Mercury deale...

Oral presentations If you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral presentationbefore the Board, this is not a requirement and the Board will decide thecase whether or not an oral presentation is made. An oral prese...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) In those cases where you continue to feel that the efforts by Ford andthe dealer to resolve a factory-related vehicle service concern have beenunsatisfactory, Ford of Canada participates in an impartial third partymediation/arbitration program...

If your vehicle must be serviced while you are traveling or living inCentral or South America, the Caribbean, or the Middle East, contact thenearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANYWORLDWIDE DIRECT MARKET OPERATIONS1555 Fairlane DriveFairlane Busi...

Protection and appearance equipment Air bag anti-theft locks All weather slush mats Bed mat/tailgate kit Bed hooks Bed mats Bedliners Carpeted floor mats with logo Door edge guards Front end covers (full and sport) Bug deflectors Instrument panel trim (brushed aluminum) Locking gas cap Lubricants an...

• The Federal Communications Commission (FCC) and Canadian RadioTelecommunications Commission (CRTC) regulate the use of mobilecommunications systems - such as two-way radios, telephones andtheft alarms - that are equipped with radio transmitters. Any suchequipment installed in your vehicle should c...

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle hasa defect that could cause a crash, orcould cause injury or death, youshould immediately inform theNational Highway Traffic SafetyAdministration (NHTSA) in additionto notifying Ford Motor Company. If NHTSA receives similar compl...

A Air bag supplemental restraintsystem ........................................103 and child safety seats ............105description ..............................103disposal ....................................107driver air bag ..........................105indicator light ...................12, 107...

trailer towing ..........................144 Loading instructions .................146 Lubricant specifications ...243, 245 Lumbar support, seats ...............90 M Manual transmission .................136 fluid capacities ........................240lubricant specifications ..........245reverse ......

Item Information Required fuel Unleaded fuel only - 87 octane Fuel tank capacity (Regularcab-Short wheel base) 62.4L (16.5 gallons) Fuel tank capacity (Regularcab-Long wheel base) 75.7 (20.0 gallons) Fuel tank capacity (SuperCab) 73.8L (19.5 gallons) Engine oil capacity (includes filterchange)-2.3L ...

Item Information Power steering fluid capacity Fill to range on dipstick. UseMotorcraft MERCON t ATF. Manual transmission fluid capacity 2 2.65L (2.8 quarts). Use MotorcraftMERCON t ATF. 3 Automatic transmission fluidcapacity-4x2 vehicles with 2.3L I4engines 2 9.4L (9.9 quarts). Use MotorcraftMERCON...