Ford 2001 F-550 v.2- Manuals

WARNING LIGHTS AND CHIMES Low fuel Illuminates as an early reminder of alow fuel condition indicated on thefuel gauge (refer to Fuel Gauge in this chapter for more information).When refueling, after the lightcomes on, the amount of fuel that is added will be less than theadvertised capacity since th...

What you should do if the Service Engine Soon light illuminates Light turns on solid: This means that the OBD II system has detected a malfunction. Temporary malfunctions may cause your Service Engine Soon light to illuminate. Examples are: 1. The vehicle has run out of fuel. (The engine may misfire...

Transmission control indicator light (TCIL) Illuminates when the TransmissionControl Switch (TCS), refer to Overdrive control in the Controls and Features chapter, has been pushed turning the transmissionoverdrive function OFF. When the TCIL (the word OFF on the gearshift) light is on, the transmiss...

Anti-lock brake system (ABS) Momentarily illuminates when theignition is turned to the ON positionto indicate a system check. If thelight remains on, continues to flashor fails to illuminate, have thesystem serviced immediately. With the ABS light on, the anti-lock brakesystem is disabled and normal...

Four wheel drive indicator (if equipped) Momentarily illuminates after theengine is STARTED. Illuminateswhen 4x4 range is engaged. If thelight continues to flash have the system serviced. Door ajar Illuminates when the ignition is inthe ON position and any door isopen. It may also momentarilyillumin...

Belt minder chime Sounds intermittently to remind you to fasten your safety belts. For information on the safety belt minder chime, refer to the Seating and safety restraints chapter. Supplemental restraint system (SRS) warning chime For information on the SRS warning chime, refer to the Seating and...

Speedometer Indicates the current vehicle speed. Engine coolant temperature gauge Indicates the temperature of theengine coolant. At normal operatingtemperature, the needle remainswithin the normal area (the areabetween the “H” and “C”). If itenters the red section, the engine isoverheating. Stop th...

The trip computer only operates with the ignition in the ON position.Trip computer features follow: Selectable features English/metric display Press this control to change the tripcomputer display between metricand English units. Mode control Each press of the MODE control willdisplay a different fe...

2. Press the E/M and MODEcontrols simultaneously. The displaywill illuminate the “AVG” indicator.While the indicator is lit, releaseboth controls to reset the averagefuel economy. Fuel range. This displays the approximate number of kilometers (miles) left to drive before the fuel tank is empty. The ...

The compass heading is displayed in average fuel economy modes, fuelrange modes and temperature modes. The compass reading may be affected when you drive near largebuildings, bridges, power lines and powerful broadcast antenna. Magneticor metallic objects placed in or on the vehicle may also affect ...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parkinglamps. Rotate to the second positionto also turn on the headlamps. Autolamp control (if equipped) The autolamp system provides lightsensitive automatic on-off control ofthe exterior lights normallycontrolled by t...

High beams • Push forward to activate. • Pull toward you to deactivate. Flash to pass Pull toward you to activate andrelease to deactivate. Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the ON position and • the headlam...

Foglamp control (if equipped) The headlamp control also operatesthe foglamps. The foglamps can beturned on only when the headlampcontrol is in the and position and the high beams are not turnedon. Pull headlamp control towards youto turn foglamps on. The foglampindicator light will illuminate. PANEL...

Always keep the sensors (located on the rear bumper/fascia) freefrom dirt, snow and ice (do not clean the sensors with sharpobjects). These elements may cause the system to operateinaccurately. If the vehicle sustains damage to the rear bumper/fascia, leavingit misaligned or bent, the sensing zone m...

• Under snowy or dirty weather conditions, your vehicle’s climatecontrol system should be left in the OFF position when the vehicle isparked. This allows the climate control system to be free fromcontamination of outside pollutants. • Do not put objects under the front seat that will interfere with ...

USING YOUR AUDIO SYSTEM AM/FM Stereo Volume/power control Press the control to turn the audiosystem on or off. Turn the control to raise or lowervolume. 1 2 3 4 AM/FM SEEK TONE CLK TUNE TONE VOL 12 FM ST DX VOL PUSH ON VOL PUSH ON VOL PUSH ON Controls and features 35

To set the minute, press and holdthe CLK control until CLOCK SETappears in the display and press theTUNE control: • to decrease minutes and • to increase minutes. The CLK control will allow you toswitch between media display mode(radio station, stereo information,etc.) and clock display mode (time)....

Volume/power control Press the control to turn the audiosystem on or off. Turn the control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition switch is turned back on. AM/FM s...

Tune adjust The tune control works in radio mode. Tune adjust in radio mode • Press to move to the next frequency down the band(whether or not a listenablestation is located there). Hold thecontrol to move through thefrequencies quickly. • Press to move to the next frequency up the band (whether or ...

Setting memory preset stations 1. Select the frequency band with the AM or the FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns,indicating the station is held i...

Speaker balance adjust Speaker sound distribution can beadjusted between the right and leftspeakers. Speaker fade adjust Speaker sound can be adjustedbetween the front and rearspeakers. Tape select • To enter tape mode while in radiomode, press the TAPE AMScontrol. BAL FADE TAPE AMS CLK Controls and...

Automatic Music Search The Automatic Music Search featureallows you to quickly locate thebeginning of the tape selectionbeing played or to skip to the nextselection. To activate the feature, momentarilydepress the TAPE AMS button.Then, press either REW (for thebeginning of the current selection) or ...

Autoset memory preset Autoset allows you to set strong radio stations without losing youroriginal manually set preset stations. This feature is helpful on tripswhen you travel between cities with different radio stations. Starting autoset memory preset 1. Select a frequency using the AM/FM select co...

Dolby 姞 noise reduction Dolby 威 noise reduction operates in tape mode. Dolby 威 noise reduction reduces the amount of hiss andstatic during tape playback. Press the control to activate (and deactivate) the Dolby 威 noise reduction. Dolby 威 noise reduction is manufactured under license from Dolby 威 Lab...

The CLK button will allow you toswitch between media display mode(radio station, stereo information,etc.) and clock display mode (time).When in clock mode, the mediainformation will display for 10seconds, when the radio is turnedon, and then revert to clockinformation. Any time that themedia is chan...

Menu mode The MENU control allows you toaccess many different featureswithin your audio system. There arethree sets of menus availabledepending upon which mode orfeature is activated. While in FM mode, two menus areavailable. If RDS is turned OFF , you can access the following: • SELECT HOURS — Refe...

Phone mode This feature allows you to controlthe factory-installed cellular phone(if equipped) through the radiocontrols. • Press the phone/mute control to enter phone mode. The playing mediawill mute. • Use SEEK, TUNE or radio presets 1 through 6 to select a phonenumber previously programmed in the...

Do not insert any promotional (odd shaped or sized) discs, ordiscs with removable labels into the CD player as jamming mayoccur. Cleaning cassette player (if equipped) Clean the tape player head with a cassette cleaning cartridge after 10 to12 hours of play in order to maintain the best sound and op...

• Terrain. Hills, mountains and tall buildings between your vehicle’s antenna and the radio station signal can cause FM reception problems.Static can be caused on AM stations by power lines, electric fences,traffic lights and thunderstorms. Moving away from an interferingstructure (out of its “shado...

To turn speed control off • Press OFF or • Turn off the vehicle ignition. Once speed control is switched off,the previously programmed setspeed will be erased. To set a speed • Press SET ACCEL. For speedcontrol to operate, the speedcontrol must be ON and thevehicle speed must be greaterthan 48 km/h ...

To disengage speed control • Depress the brake pedal or • Depress the clutch pedal(if equipped). Disengaging the speed control willnot erase the previouslyprogrammed set speed. Pressing OFF will erase thepreviously programmed set speed. ON OFF Controls and features 75

TILT STEERING WHEEL (IF EQUIPPED) Pull the tilt steering control towardyou to move the steering wheel upor down. Hold the control whileadjusting the wheel to the desiredposition, then release the control tolock the steering wheel in position. Never adjust the steering wheel when the vehicle is movin...

Push the control on the end of thestalk to activate washer. Push andhold for a longer wash cycle. Thewasher will automatically shut offafter ten seconds of continuous use. OVERDRIVE CONTROL (IF EQUIPPED) Activating overdrive (Overdrive) is the normal drive position for the best fuel economy. The ove...

POWER WINDOWS (IF EQUIPPED) Press and hold the rocker switches to open and close windows. • Press the top portion of therocker switch to close. • Press the bottom portion of therocker switch to open. One touch down • Press AUTO completely down andrelease quickly. The driver’swindow will open fully. ...

Window lock The window lock feature allows onlythe driver to operate the powerwindows. To lock out all the window controlsexcept for the driver’s press the leftside of the control. Press the rightside to restore the window controls. Accessory delay (if equipped) With accessory delay, the window swit...

CHILDPROOF DOOR LOCKS When these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thedoors are unlocked. The childproof locks are located onrear edge of each rear door andmust be set separately for eachdoor. Setting the lock for one door...

2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the center position to lock mirrors in place. 4. Adjust spotter mirrors (if equipped) manually. Fold-away mirrors Fold the side mirrors in carefully when driving through a narrow space,like an automatic car wash. The teles...

• Utility compartment • Coin holder • Pen holder • Writing surface • Space for lap-top computer REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RS-210 ofIndustry Canada. Operation is subject to the following two conditions:(1) This device may not cause h...

Unlocking the doors Press this control to unlock thedriver’s door. The interior lamps willilluminate. Press the control a second timewithin five seconds to unlock alldoors. Locking the doors Press this control to lock all doors. To confirm all doors are closed andlocked, press the control a secondti...

Replacing lost transmitters If a remote transmitter has been lostand you would like to remove itfrom the vehicle’s memory, or youwould like to purchase additionalremote transmitters and have themprogrammed to your vehicle: • Take all your vehicle’s transmitters to your dealer forprogramming, or • Pe...

TAILGATE LOCK (IF EQUIPPED) Your vehicle may be equipped with atailgate lock designed to preventtheft of the tailgate. • Insert ignition key and turn to theright to engage lock. • Turn ignition key to the left tounlock. TAILGATE REMOVAL Your tailgate is removable to allowmore room for loading. 1. Lo...

SEATING Full bench seat (if equipped) • Lift the track release bar to movethe seat forward or backward.Ensure that the seat is relatchedinto place. • Pull up on the release leverlocated at the bottom of theseatback to quickly fold theseatback forward. 40/20/40 split bench seat (if equipped) • Lift t...

Captain’s chair (if equipped) • Lift the track release bar to movethe seat forward or rearward.Make sure that the seat isrelatched into place. • Pull the release lever handlelocated on the side of the seat upto move the seat back forward orbackward. • Push down the release lever (ifequipped) located...

Press to raise or lower the frontportion of the seat cushion. Press to raise or lower the rearportion of the seat cushion. Press the control to move the seatforward, backward, up or down. Using the manual lumbar support Turn the lumbar support controltoward the front of vehicle to movethe lumbar sup...

RETURNING THE SEAT TO SEATING POSITION Always be sure that the seat is in a latched position, whether theseat is occupied or empty. If not latched, the seat may cause injury during a sudden stop. 1. Pull control on the side of the seat to release seat cushion fromstorage position. 2. Push seat cushi...

Each seating position in your vehicle has a specific safety beltassembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on theoutside shoulder only. Never wear the shoulder belt under the arm. 2)Never swing the safety belt around your n...

The front and rear outboard safety restraints in the vehicle arecombination lap and shoulder belts. The front passenger and rear seatoutboard safety belts have two types of locking modes described below: Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing freesho...

How to use the automatic locking mode • Buckle the combination lap andshoulder belt. • Grasp the shoulder portion andpull downward until the entirebelt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automat...

How to disengage the automatic locking mode Ford recommends that all safety belt assemblies and attachinghardware should be inspected by a qualified technician after any collision. Safety belt assemblies not in use during a collision should alsobe inspected and replaced if either damage or improper ...

Safety belt replacement label The short plastic boot on the frontsafety belt at the passengeroutboard anchor location covers a“Replace Belt” label on the safetybelt. In the event of a collision, thecolored label (REPLACE BELT)may become visible. If this occurs, the safety belt must be replaced. When...

Failure to follow these instructions will affect the performance ofthe safety belts and increase the risk of personal injury. Safety belt pretensioner Your vehicle may be equipped with safety belt pretensioners at the driverand front outboard passenger seating positions. The Seat Integrated Restrain...

• Regular Cab and 4–door CrewCab • 4–door Super Cab (if equipped) Seating and safety restraints 100

To lower the shoulder belt height, push the button and slide the heightadjuster down. To raise the height of the shoulder belt, slide the heightadjuster up. Pull down on the height adjuster to make sure it is locked inplace. Position the shoulder belt height adjusters so that the belt restsacross th...

Belt minder The Belt Minder feature is a supplemental warning to the safety beltwarning function. This feature provides additional reminders to thedriver that the driver’s safety belt is unbuckled by intermittentlysounding a chime and illuminating the safety belt warning lamp in theinstrument cluste...

• After step 5 the safety belt warning light will be turned on for threeseconds. 6. Within seven seconds of the safety belt warning light turning off,buckle then unbuckle the safety belt. • This will disable Belt Minder if it is currently enabled, or enable BeltMinder if it is currently disabled. 7....

The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion ...

The diagnostic module monitors its own internal circuits and thesupplemental air bag electrical system warning (including the impactsensors), the system wiring, the air bag system readiness light, the airbag back up power and the air bag ignitors. Determining if the system is operational The SRS use...

Passenger air bag ON/OFF switch (if equipped) An air bag ON/OFF switchhas been installed in this vehicle. Before driving, always look at the face of the switch tobe sure the switch is in the properposition in accordance with theseinstructions and warnings. Failureto put the switch in a properpositio...

3. Medical condition. A passenger has a medical condition which, according to his or her physician: • causes the passenger air bag to pose a special risk for the passenger;and • makes the potential harm from the passenger air bag in a crashgreater than the potential harm from turning OFF the air bag...

• the child has a medical condition that, according to the child’sphysician, makes it necessary for the child to ride in the front seat sothat the driver can monitor the child’s condition. 3. Medical condition: A passenger has a medical condition that, according to his or her physician: • poses a sp...

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant orchild restraint you might use. When possible, always place children under age 12...

SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all of the manufacturer’s instructions with thesafety seat you put in your vehicle. If you do not install and use thesafety seat properly, the ...

Attaching safety seats with tether straps Some manufacturers make safety seats that include a tether strap thatgoes over the back of the vehicle seat and attaches to an anchoringpoint. Other manufacturers offer the tether strap as an accessory.Contact the manufacturer of your child safety seat for i...

The SuperCab rear seat has three straps behind the top of the seat backthat function as both routing loops for the tether straps and anchorloops. The tether strap anchors in your vehicle are in the following positions(shown from top view): Attach the tether strap only to the appropriate tether ancho...

Tether strap attachment rear SuperCab only There are three loops of webbing just above the back of the rear seat(along the bottom edge of the rear window) in the SuperCab. Theseloops are to be used as both routing loops and anchor loops for childsafety seat tether straps. Many tether straps cannot b...

PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. Thissystem meets all Canadian Interference-Causing Equipment standardrequirements regulating the impulse electrical field strength of radionoise. When starting a fuel-injected engine, avoid pressing the a...

Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate. STARTING THE ENGINE NOTE: Whenever you start your vehicle, release the key as soon as the engine sta...

Using the engine block heater (if equipped) An engine block heater warms theengine coolant, which improvesstarting, warms up the engine fasterand allows the heater-defrostersystem to respond quickly. Use of anengine block heater is stronglyrecommended if you live in a regionwhere temperatures reach ...

WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or otherreproductive harm. In addition, certain fluids contained in vehicles andcertain products of component wear contain or...

BRAKES Your service brakes are self-adjusting. Refer to the scheduledmaintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate aperformance concern with the vehicle’s brake system. In normaloperation, automotive brake systems may emit occasional or int...

Using four wheel ABS • In an emergency or when maximum efficiency from the four wheelABS is required, apply continuous force on the brake. The four wheelABS will be activated immediately, thus allowing you to retain fullsteering control of your vehicle and, providing there is sufficientspace, will e...

Parking brake Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops. The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released....

Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy. STEERING YOUR VEHICLE Your vehicle is equipped with power steering. Power steering uses energyfrom the engine to help steer the vehicle. Never hold the steeri...

PREPARING TO DRIVE YOUR VEHICLE Utility vehicles have a significantly higher rollover rate thanother types of vehicles. In a rollover crash, an unbelted person is significantly more likelyto die than a person wearing a seat belt. Your vehicle has special design and equipment features to make itcapab...

AUTOMATIC TRANSMISSION OPERATION (IF EQUIPPED) Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever from being moved from P (Park) when the ignition isin the ON position unless brake pedal is depressed. If you cannot move the gearshift ...

Driving with a 4–speed automatic transmission Understanding gearshift positions To put your vehicle in gear, start the engine, depress the brake pedal,then move gearshift lever out of P (Park). Hold the brake pedal down while you move the gearshift leverfrom P (Park) to another position. If you do n...

(Overdrive) The normal driving position for thebest fuel economy. Transmissionoperates in gears one through four. (Overdrive) can be deactivated by pressing the transmission controlswitch (TCS) on the end of thegearshift lever. The transmission control indicatorlight (TCIL) (the word OFF) on theend ...

1 (First) Use 1 (Low) to provide maximumengine braking on steepdowngrades. Upshifts can be madeby shifting to 2 (Second) or to(Overdrive). Selecting 1 (Low) athigher speeds causes the transmission to shift to a lower gear, and willshift to 1 (Low) after vehicle decelerates to the proper speed. Force...

When starting a vehicle with a manual transmission, you must: 1. Make sure the parking brake isfully set. 2. Depress the clutch pedal fully. 3. Put the gearshift lever in N(Neutral). 4. Turn the ignition to position 5(START) to start the engine, let theengine idle for a few seconds. 5. Depress the b...

Recommended shift speeds Downshift according to the following charts for your specificengine/drivetrain combination: Maximum downshift speeds 1 5-speed transmission Shift from: Transfer case position (if equipped) 2 2H or 4H 4L D (Overdrive) - 4 72 km/h (45 mph) 35 km/h (22 mph) 4 - 3 56 km/h (35 mp...

Parking your vehicle 1. Disengage the clutch, apply brakeand shift into N (Neutral). 2. Set parking brake. 3. Shift into 1 (First). 4. Turn the ignition key to position3 (OFF). 1 2 4 R 3 D 1 2 4 R L 3 D 3 2 1 5 4 Driving 142

Do not park your vehicle in Neutral, it may move unexpectedlyand injure someone. Use 1 (First) gear and set the parking brake fully. Reverse Make sure that your vehicle is at a complete stop before you shift into R(Reverse). Failure to do so may damage the transmission. Put the gearshift lever in N ...

FOUR-WHEEL DRIVE (4WD) OPERATION (IF EQUIPPED) For important information regarding safe operation of this typeof vehicle, see Preparing to drive your vehicle in this chapter. When four–wheel drive (4WD) is engaged, power is supplied to all fourwheels through a transfer case. 4WD power can be selecte...

• automatic hub locks can bemanually overridden by rotatingthe hub lock control from AUTOto LOCK. Automatic operation ofthe hub locks is recommended. • For proper operation, makesure that the arrow and theindicator dot on the hub arealigned. Manual 4x4 system (if equipped) The 4WD system is engaged ...

• LOW RANGE –momentarily illuminates when the ignition isturned to the ON position.Illuminates when 4L (4x4 Low) isengaged. Using a manual 4WD system (if equipped) 2H (2WD High) – Power to rear axle only. 4H (4WD High) – Power to front and rear axles. N (Neutral) – No power to either axle. 4L (4WD L...

Shifting from 4H (4WD high) to 2H (2WD high) Move the transfer case lever to 2H(2WD High) at a stop or anyforward speed up to 88 km/h (55mph). With the vehicle at complete stop,disengage the locking hubs(optional) by rotating the hub lockcontrol from LOCK to FREE. • For proper operation, make sure t...

4. Move the transfer case shift leverthrough N (Neutral) directly to 4H(4WD High) or 2H (2WD high) andhold the shift lever in position untilthe transfer case has fully engaged(up to 15 seconds). 5. If the transfer case does not engage, repeat steps 1 through 4. Using the N (Neutral) position The tra...

Shifting from 2WD (2WD high) to 4x4 HIGH (4WD high) Rotate the 4WD control to the 4x4HIGH position at speeds up to 88km/h (55 mph). • To prevent damage, theelectronic shift 4WD system isdesigned to engage 4x4 HIGH(4WD high) when the vehicleis moving. If the 4x4 indicatorlight does not illuminate whe...

4. Move the 4WD control to the 4x4LOW position. 5. Hold the shift command until theLOW RANGE indicator lightilluminates. 6. If the LOW RANGE indicator light does not illuminate after 15 seconds, start the vehicle moving,then repeat steps 1 through 5before reporting any shift concernsto your dealer. ...

• Maximum Trailer Weight: Maximum weight of a trailer the loaded vehicle (including occupants and cargo) is permitted to tow. It isdetermined by subtracting the weight of the loaded trailer towingvehicle from the GCWR for the towing vehicle. • Trailer Weight Range: Specified weight range that the tr...

TRAILER TOWING Your vehicle may tow aConventional/Class IV trailer or fifthwheel trailer provided the maximumtrailer weight is less than or equal tothe maximum trailer weight listedfor your engine and rear axle ratioon the following charts. 2nd unit bodies are not included inmaximum trailer weight r...

F-450 with manual transmission Engine Rear axle ratio Maximum GCWR - kg (lbs.) Maximum trailer weight - kg (lbs.) 1 6.8L 4.88 9 979 (22 000) 4 536 (10 000) 6.8L 5.38 9 979 (22 000) 4 536 (10 000) 1 Conventional/Class IV trailer hitch only. Fifth wheel trailer maximum weights can be calculated by sub...

Hitches Do not use hitches that clamp onto the vehicle’s bumper or attach to theaxle. You must distribute the load in your trailer so that 10%–15% of thetotal weight of the trailer is on the tongue. Load equalizing hitch When hooking up a trailer using a load equalizing hitch, always use thefollowin...

Do not connect a trailer’s hydraulic brake system directly to yourvehicle’s brake system. Your vehicle may not have enough braking power and your chances of having a collision greatly increase. The braking system of the tow vehicle is rated for operation at theGVWR not GCWR. Trailer lamps Trailer la...

Trailer towing tips • Practice turning, stopping and backing up before starting on a trip toget the feel of the vehicle trailer combination. When turning, makewider turns so the trailer wheels will clear curbs and other obstacles. • Allow more distance for stopping with a trailer attached. • The tra...

• Place the transmission in N (Neutral). • Maximum speed is 56 km/h (35 mph). • Maximum distance is 80 km (50 miles). If a distance of 80 km (50 miles) or a speed of 56 km/h (35 mph) mustbe exceeded, you must disconnect the driveshaft. Ford recommends thedriveshaft be removed/installed only by a qua...

• The Front Axle Accessory Reserve Capacity and the Total AccessoryReserve Capacity listed on the bottom right of the Safety ComplianceCertification Label will determine whether or not the addition of asnowplow will overload your vehicle. • The weight of the snowplow and supporting components distri...

Snowplowing with your air bag equipped vehicle Your vehicle is equipped with driverand passenger air bag SupplementalRestraint System (SRS). The SRS isdesigned to activate when thevehicle sustains sufficientlongitudinal deceleration. Careless or high speed driving while plowing snow which results in...

GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford offers acomplimentary roadside assistance program. This program is separatefrom the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for the Basic warranty period (Canada) o...

FUSES AND RELAYS Fuses If electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check the appropriatefuses before replacing any electricalcomponents. NOTE: Always replace a fuse with one that has the specified amperage r...

Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel bythe brake pedal. Remove the panel cover to access the fuses. To remove the fuse panel cover,turn the panel fastenerscounterclockwise. To remove a fuse use the fuse pullertool provided on the fuse...

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 20A Turn/Hazard Lamps 2 — Not Used 3 20A Cigar Lighter, Data Link Connector 4 10A Glove Box Lamp, Map Lamps, PowerMirrors, Underhood Lamp 5 — Not Used 6 — Not Used 7 5A Power Window/Loc...

Power distribution box The power distribution box, trailertow and electronic shift on the flyrelay blocks are located in theengine compartment near the brakemaster cylinder. The power distribution box contains high-current fuses that protect yourvehicle’s main electrical systems from overloads. Alwa...

The high-current fuses and relays are coded as follows. Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 7.5A * Trailer Tow Left Stop/Turn Lamp 2 10A* Washer Pump 3 7.5A* Trailer Tow Right Stop/Turn Lamp 4 20A* Trailer Tow Backup Lamps, Trailer TowPark Lamps 5 20A* (Gasoline ...

CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel firmlyand slowly move to a safe place on the side of the road. Spare tire information Your vehicle may be equipped with a spare tire that can be use...

• one wheel nut wrench. Slide oversquare end of jack handle. 2. If equipped, unlock and remove the spare tire lock from the rearbumper drive tube using the the spare tire lock key and the jack handle. 3. Insert the hooked end of the jackhandle into the rear bumper drivetube. The handle will stop mov...

Stowing the spare tire 1. Lay the tire on the ground with the valve stem facing up. 2. Slide the wheel under the vehicleand install the retainer through thewheel center. 3. Turn the jack handle clockwiseuntil the tire is raised to its originalposition underneath the vehicle. Theeffort to turn the ja...

To prevent the vehicle frommoving when you change a tire, be sure the parking brake isset, then block (in bothdirections) the wheel that isdiagonally opposite (other sideand end of the vehicle) to the tirebeing changed. 2. Turn engine OFF and block the diagonally opposite wheel (block notprovided). ...

The following steps apply to F250/F350 only: 6. Insert the hooked end of the jackhandle into the jack and use thehandle to slide the jack under thevehicle. 7. Position the jack according to thefollowing guides: • Front (4x2) Roadside emergencies 183

• Front passenger side (4x4) • Front driver side (4x4) Make sure the jack fits into thenotched area next to the differentialhousing. • Rear Roadside emergencies 184

Never use the front or reardifferential as a jacking point. To lessen the risk ofpersonal injury, do not put any part of your body under thevehicle while changing a tire. Donot start the engine when yourvehicle is on the jack. The jack isonly meant for changing the tire. 8. Turn the jack handle cloc...

The following steps apply to F350 chassis Cab F450/F550 only: 12. Slide the notched end of thejack handle over the release valveand use the handle to slide the jackunder the vehicle. Make sure thevalve is closed by turning itclockwise. 13. Position the jack according tothe following guides: • Front ...

The following steps apply to all vehicles: 19. Remove the jack and fully tightenthe lug nuts in the order shown.20. Stow the flat tire. Refer to Stowing the spare tire if the vehicle is equipped with a spare tire carrier.21. Stow the jack, jack handle andlug wrench. Make sure the jack issecurely fas...

JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Batteries contain sulfuric acid which can burn skin, eyes, andclothing, if contacted. Do not attempt to push-start your vehicle. ...

Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+)term...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor/fuel injection system. Do not use fuel lines, engine rocker ...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member, your roadside assistance center. On 4x2 vehicles, it is acceptable to tow the vehicle with the front wheelson the ground and the rear wheels off the ground using a wheel lift or aslin...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a scheduled maintenance guide which makes trackingroutine service easy. If your vehicle requires professional service, your dealership can providethe...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel. 2. Go to the front of the vehicle andrelease the auxiliary latch locatedunder the right center of the hood.Slide the handle to release theauxiliary latch. 3. Lift the hood ...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 5.4L V8/6.8L V10 gasoline engines Refer to the 7.3 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement for diesel engine component locations. 1. Engine oil dipstick 2. Clutch fluid reservoir (manual transmission) 3. Brake fluid r...

ENGINE OIL Checking the engine oil Refer to the scheduled maintenance guide for the appropriate intervalsfor checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into theoil pan. 3. Set the parking brake and ensure t...

• If the oil level is below the MINmark, add enough oil to raise thelevel within the MIN-MAX range. • Oil levels above the MAX mark may cause engine damage. Some oilmust be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil ...

BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked andrefilled as needed. Refer to thescheduled maintenance guide forthe service interval schedules. 1. Clean the reservoir cap beforeremoval to prevent dirt or waterfrom entering the reservoir. 2. Visually inspect the fluid leve...

CLUTCH FLUID (IF EQUIPPED) Check the clutch fluid level. Refer to the scheduled maintenance guidefor the service interval schedules. Use only a DOT 3 brake fluid designed to meet Ford specificationESA-M6C25–A. Refer to Capacities and specifications. Brake fluid is toxic. If brake fluid contacts the ...

WINDSHIELD WASHER FLUID Washer fluid Check the washer fluid wheneveryou stop for fuel. The reservoir ishighlighted with a symbol. If the level is low, add enough fluidto fill the reservoir. In very coldweather, do not fill the reservoir allthe way. Only use a washer fluid that meets Ford specificati...

Your vehicle was factory-filled with a 50/50 engine coolant and waterconcentration. If the concentration of coolant falls below 40% or above60%, the engine parts could become damaged or not work properly. A 50–50 mixture of coolant and water provides the following: • Freeze protection down to -36° C...

Adding engine coolant When adding coolant, make sure it is a 50/50 mixture of engine coolantand distilled water. Add the mixture to the coolant reservoir, when the engine is cool , until the appropriate fill level is obtained. Do not add engine coolant when the engine is hot. Steam andscalding liqui...

• Do not use alcohol, methanol or brine or any engine coolantsmixed with alcohol or methanol antifreeze (coolant). Alcohol and other liquids can cause engine damage from overheating orfreezing. • Do not add extra inhibitors or additives to the coolant. These can be harmful and compromise the corrosi...

After any coolant has been added, check the coolant concentration seeChecking Engine Coolant section). If the concentration is not 50/50(protection to –34°F/–36°C), drain some coolant and adjust theconcentration. It may take several drains and additions to obtain a 50/50coolant concentration. Whenev...

Refer to the chart on the coolant container to ensure the coolantconcentration in your vehicle will provide adequate freeze protection. Never increase the engine coolant concentration above 60% (protection to –60°F). At a level over 60%, your engine could overheatand become damaged. If you drive in ...

CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid.Refer to the scheduled maintenanceguide for the service intervalschedules. If adding fluid isnecessary, use only MERCON 威 ATF. Check the fluid level when it is at ambient temperature, 20° – 80° F(-7° – 25° C): 1. Check the fluid...

TRANSMISSION FLUID Checking automatic transmission fluid (if equipped) Refer to your scheduled maintenance guide for scheduled intervals forfluid checks and changes. Your transmission does not consume fluid.However, the fluid level should be checked if the transmission is notworking properly, i.e., ...

If an overfill occurs, excess fluidshould be removed by a qualifiedtechnician. An overfill condition oftransmission fluid may causeshift and/or engagementconcerns and/or possibledamage. Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug an...

Checking and adding transfer case fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug andinspect the fluid level. 3. Add only enough fluid throughthe filler opening so that the fluidlevel is at the bottom of theopening. Use only fluid that meets Ford specifications. Refer to the ...

Changing the air filter element (gasoline engines only) 1. Loosen the clamp that securesthe air filter element in place. 2. Carefully separate the two halvesof the air filter housing. 3. Remove the air filter elementfrom the open end of the air filterhousing. 4. Install a new air filter element, ens...

Batteries normally produce explosive gases which can causepersonal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery,always shield your face and protect your eyes. Always provide properventilation. When lifting a plastic-case...

6. Drive the vehicle to complete the relearning process. • The vehicle may need to be driven 16 km (10 miles) or more torelearn the idle and fuel trim strategy. • If you do not allow the engine to relearn its idle trim, the idlequality of your vehicle may be adversely affected until the idletrim is ...

Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from thewindshield and lock into the serviceposition. 2. Turn the blade at an angle fromthe wiper arm. Push the lock pinmanually to release the blade andpull the wiper blade down towardthe windshield to remove it from ...

SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has beenparked for at least one hour or has been driven less than 5 km(3 miles). • Adjust tire pressure to recommended specifications found on theCe...

• Five tire rotation Replacing the tires Replace the tires when the wearband is visible through the tiretreads. When replacing full size tires, never mix radial bias-belted, orbias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same s...

Do not replace your tires with “high performance” tires or largersize tires. Failure to follow these precautions may adversely affect thehandling of the vehicle and make it easier for the driver to lose control and roll over. Tires that are larger or smaller than your vehicle’s original tires may al...

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tankmay cause leakage and lead to fuel spray and fire. The fuel system may be under pressure. If the fuel filler cap isventing vapor or if you hear a hissing sound, w...

Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materialsand any open flames beforefueling your vehicle. • Always turn off the vehicle beforefueling. • Automotive fuels can be harmfulor fatal if swallowed. Fuel such asgasoline is highly toxic and ifswallowed ...

The flow of fuel through a fuel pump nozzle can produce staticelectricity, which can cause a fire if fuel is pumped into an ungrounded fuel container. Use the following guidelines to avoid static build-up when filling anungrounded fuel container: • Place approved fuel container on the ground. • DO N...

Fuel quality If you are experiencing starting, rough idle or hesitation driveabilityproblems during a cold start, try a different brand of “Regular” unleadedgasoline. “Premium” unleaded gasoline is not recommended (particularlyin the United States) because it may cause these problems to becomemore p...

Fuel Filler Cap Your fuel tank filler cap has an indexed design with a 1/8 turn on/offfeature. When fueling your vehicle: 1. Turn the engine off. 2. Carefully turn the filler cap counterclockwise 1/8 of a turn until it stops. 3. Pull to remove the cap from the fuel filler pipe. 4. To install the cap...

Calculating fuel economy 1. Fill the fuel tank completely and record the initial odometer reading(in kilometers or miles). 2. Each time you fill the tank, record the amount of fuel added (in litersor gallons). 3. After at least three to five tank fill-ups, fill the fuel tank and recordthe current od...

• Transmissions give their best fuel economy when operated in the topcruise gear and with steady pressure on the gas pedal. • Four-wheel-drive operation (if equipped) is less fuel efficient thantwo-wheel-drive operation. • Close windows for high speed driving. EPA window sticker Every new vehicle sh...

Washing your vehicle Wash your vehicle regularly withcold or lukewarm water. Never usestrong detergents or soap. If yourvehicle is particularly dirty, use aquality car wash detergent. Alwaysuse a clean sponge, washing gloveor similar device and plenty of waterfor best results. To avoid spots,avoid w...

Avoid getting wax on the windshield, or on any surfaces which appearcoarse or bumpy. If you have wax applied at a commercial car wash, it isrecommended that you clean the wiper blades and windshield asdescribed in Cleaning the wiper blades and windshield. Repairing paint chips Minor scratches or pai...

Cleaning the windshield, wiper blades and rear window If the wiper blades do not wipe properly, clean the wiper blade rubberelement with undiluted windshield washer solution or a mild detergent.To avoid damaging the blades, do not use fuel, kerosene, paint thinner orother solvents. If the wiper stil...

Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended forcleaning upholstery or carpets. Do not bleach or dye the belts, becausethese actions may weaken the belt webbing. Check the safety belt system periodically to make sure there are nonicks, tears ...

MOTORCRAFT PART NUMBERS Component* 5.4L V8 engine 6.8L V10 engine Air filter element FA-1634 FA-1634 Fuel filter FG-986B FG-986B Oil filter FL-820-S FL-820-S PCV valve EV-233 EV-233 Battery (Standard) BXT-65-650 BXT-65-650 Battery (Optional) BXT-65-750 BXT-65-750 Spark plugs-platinum** AWSF-22W AWSF...

LUBRICANT SPECIFICATIONS Item Ford partname orequivalent Ford partnumber Fordspecification Front axle(4X4) Motorcraft SAE75W-90Premium 4x4Front AxleLubricant XY-75W90-TQL WSP-M2C201-A Rear axle Motorcraft SAE75W-140 HighPerformanceSynthetic RearAxle Lube 1 F1TZ-19580-B WSL-M2C192-A Motorcraft SAE80W...

Item Ford partname orequivalent Ford partnumber Fordspecification Engine oil Motorcraft SAE5W-20 SuperPremium MotorOil XO-5W20-QSP WSS-M2C153-Hand APICertificationMark Hinges, latches,striker plates,fuel filler doorhinge and seattracks Multi-PurposeGrease DOAZ-19584-AAorF5AZ-19G209-AA ESB-M1C93-B or...

F250-Crew Cab Dimension Body style Crew Cab 4x2 Crew Cab 4x4 (1) Overall height 1 960 mm (77.2 in) a / 1 883 mm (74.1 in) b 2 053mm (80.8 in) a / 2 052 mm (80.8 in) b (2) Track (Front /Rear) 1 745 mm (68.7 in)/1 729 mm (68.1 in) a,b 1 736 mm (68.4 in)/1 729 mm (68.1 in) a,b (3) Overall width 1 988 m...

Ford Extended Service Plan You can get more protection for your new car or light truck bypurchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESPis an optional service contract which is backed by Ford Motor Companyor Ford Motor Service Company (in the U.S.) and Ford of Canada (inCanada). ...

If you have questions or concerns, or are unsatisfied with the service youare receiving, follow these steps:1. Contact your Sales Representative or Service Advisor at yourselling/servicing dealership.2. If your inquiry or concern remains unresolved, contact the SalesManager or Service Manager at the...

Consumer candidates for Board membership are recruited and trained byan independent consulting firm. The dealership Board member is chosenfrom Ford and Lincoln Mercury dealership management, recognized fortheir business leadership qualities. What the Board needs To have your case reviewed you must c...

Oral presentations If you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral presentationbefore the Board, this is not a requirement and the Board will decide thecase whether or not an oral presentation is made. An oral prese...

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY) In those cases where you continue to feel that the efforts by Ford andthe dealer to resolve a factory-related vehicle service concern have beenunsatisfactory, Ford of Canada participates in an impartial third partymediation/arbitration program...

If your vehicle must be serviced while you are traveling or living inCentral or South America, the Caribbean, or the Middle East, contact thenearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANYWORLDWIDE DIRECT MARKET OPERATIONS1555 Fairlane DriveFairlane Busi...

Protection and appearance equipment Air bag anti-theft locks All weather vinyl floor mats Bed mat/bedliner tailgate covers Bed hooks Bed mats Bedliners Brush guard Carpet floor mats Cleaners, waxes and polishes Diamond plate bed rail caps Diamond plate front box protection Diamond plate splash guard...

ORDERING ADDITIONAL OWNER’S LITERATURE To order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORATEDP.O. Box 07150Detroit, Michigan 48207 Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST (Items in this c...

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle hasa defect that could cause a crash, orcould cause injury or death, youshould immediately inform theNational Highway Traffic SafetyAdministration (NHTSA) in additionto notifying Ford Motor Company. If NHTSA receives similar compl...

A Accessory delay ..........................80 Air bag supplementalrestraint system ........................107 and child safety seats ............109description ..............................107disposal ....................................111driver air bag ..........................109indicator lig...

safety belt .................................12service engine soon ..................10speed control ............................76turn signal indicator .................13 Load limits .................................154 GAWR ......................................154GVWR ..............................

Warning lights (see Lights) .......10 Washer fluid ..............................206 Water, Driving through .............156 Windows power .........................................79 Windshield washer fluid andwipers checking and adding fluid .....206checking and cleaning ............221operation .....

Item Information Required fuel Unleaded fuel only - 87 octane Fuel tank capacity Refer to Refill capacities in the Capacities and specifications chapter. Engine oil (includesfilter change) 5.7L (6.0 quarts). Use Motorcraft SAE 5W-20Super Premium Motor Oil, Ford specificationWSS-M2C153-H. Tire size a...

MERCON 威 and MERCON 威 V type fluids are not interchangeable. DO NOT mix MERCON 威 and MERCON 威 V. Use of a transmission fluid that indicates dual usage (MERCON 威 and MERCON 威 V) in an automatic transmission application requiring MERCON 威 may cause transmission damage. Use of any fluid other than ther...