Ford 2001 F-550 v.1- Manuals

Using your vehicle as an ambulance If your light truck is equipped with the Ford Ambulance Preparation Package, it may be utilized as an ambulance. Ford urges ambulance manufacturers to follow the recommendations of the Ford Incomplete Vehicle Manual, Ford Truck Body Builder’s Layout Book and the QV...

These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat InstallationWarning Child Seat TetherAnchorage Brake System Anti-Lock Brake System Brake Fluid -Non-Petroleum Based Tr...

0 0 0 0 0 0 0 0 0 0 MPH 20 km/h 40 60 80 100 120 140 160 0 10 20 30 40 50 60 70 80 90 100 LOWFUEL DOORAJAR LOW RANGE 4 X 4 CRUISE BRAKE ! ABS + - L E F H RPM 1000 X 0 1 2 3 5 6 4 P R N 2 1 8 C 18 H D FUEL FILL SERVICE ENGINE SOON O P ON COAST OFF PANEL DIM SET ACCEL RES Headlamp control (pg. 23) Tur...

WARNING LIGHTS AND CHIMES Low fuel Illuminates as an early reminder of alow fuel condition indicated on thefuel gauge (refer to Fuel Gauge in this chapter for more information).When refueling, after the lightcomes on, the amount of fuel that is added will be less than theadvertised capacity since th...

What you should do if the Service Engine Soon light illuminates Light turns on solid: This means that the OBD II system has detected a malfunction. Temporary malfunctions may cause your Service Engine Soon light to illuminate. Examples are: 1. The vehicle has run out of fuel. (The engine may misfire...

Transmission control indicator light (TCIL) Illuminates when the TransmissionControl Switch (TCS), refer to Overdrive control in the Controls and Features chapter, has been pushed turning the transmissionoverdrive function OFF. When the TCIL (the word OFF on the gear shift)light is on, the transmiss...

Turn signal Illuminates when the left or rightturn signal or the hazard lights areturned on. If one or both of theindicators stay on continuously orflash faster, check for a burned-outturn signal bulb. Refer to Bulbs in the Maintenance and care chapter. High beams Illuminates when the high beamheadl...

Door ajar Illuminates when the ignition is inthe ON position and any door isopen. It may also momentarilyilluminate after the engine is startedand all doors are closed. Oil pressure/Engine coolant This light will illuminate when theignition is in the ON position andthe: • engine coolant temperature ...

Supplemental restraint system (SRS) warning chime For information on the SRS warning chime, refer to the Seating and safety restraints chapter. Key-in-ignition warning chime Sounds when the ignition key is left in the ignition in the OFF/LOCK orACC position and the driver’s door is opened. Headlamps...

When refueling the vehicle from an empty indication, the amount of fuelthat can be added will be less than the advertised capacity due to thereserve fuel. Speedometer Indicates the current vehicle speed. Engine coolant temperature gauge Indicates the temperature of theengine coolant. At normal opera...

Selectable features English/metric display Press this control to change the tripcomputer display between metricand English units. Mode control Each press of the MODE control willdisplay a different feature as follows: Average fuel economy. The display will indicate the vehicle’saverage fuel economy ...

2. Press the E/M and MODEcontrols simultaneously. The displaywill illuminate the “AVG” indicator.While the indicator is lit, releaseboth controls to reset the averagefuel economy. Fuel range. This displays the approximate number of kilometers (miles) left to drive before the fuel tank is empty. The ...

The compass heading is displayed in average fuel economy modes, fuelrange modes and temperature modes. The compass reading may be affected when you drive near largebuildings, bridges, power lines and powerful broadcast antenna. Magneticor metallic objects placed in or on the vehicle may also affect ...

6. To exit the zone setting mode and save the displayed zone in memory,release both controls for greater than five seconds. Compass calibration adjustment Perform this adjustment in an open area free from steel structures andhigh voltage lines. For optimum calibration, turn off all electrical access...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parkinglamps. Rotate to the second positionto also turn on the headlamps. High beams Push forward to activate. Pull toward you to deactivate. Flash to pass Pull toward you to activate andrelease to deactivate. Daytime r...

Always remember to turn on your headlamps at dusk or duringinclement weather. The Daytime Running Light (DRL) System does not activate your tail lamps and generally may not provideadequate lighting during these conditions. Failure to activate yourheadlamps under these conditions may result in a coll...

The OFF indicator remains illuminated when the system is disabled. Thesystem defaults to ON every time the reverse gear is selected. Press thecontrol to disable or enable the system. The indicator will remain illuminated to indicate a failure of the reversesensing system. The reverse sensing system ...

CLIMATE CONTROL SYSTEM Heater only system (if equipped) Fan speed control Controls the volume of air circulatedin the vehicle. Temperature control Controls the temperature of theairflow inside the vehicle. Onheater-only systems, the air cannotbe cooled below the outsidetemperature. Mode selector con...

Operating tips • In humid weather conditions, place the climate control system inDEF before driving. This will reduce fogging on your windshield. Oncethe windshield has been cleared, operate the climate control system asdesired. • To reduce humidity buildup inside the vehicle in cold weatherconditio...

Manual heating and air conditioning system Fan speed control Controls the volume of air circulatedin the vehicle. Temperature control knob Controls the temperature of theairflow inside the vehicle. Mode selector control Controls the direction of the airflowto the inside of the vehicle. The air condi...

To aid in side window defogging/demisting in cold weather conditions: 1. Select PANEL & FLOOR 2. Set the temperature control to full heat 3. Set the fan speed to HI 4. Direct the outer panel vents towards to side windows To increase airflow to the outer panel vents, close the central panelvents....

Seek function in radio mode • Press to find the next listenable station down thefrequency band. • Press to find the next listenable station up the frequency band. Radio station memory preset The radio is equipped with four station memory preset controls. Thesecontrols can be used to select up to fou...

Speaker balance adjust Speaker sound distribution can beadjusted between the right and leftspeakers. Press the TONE control three times,then use the volume knob to adjustthe desired level. Speaker fade adjust (if equipped) Speaker sound can be adjustedbetween the front and rearspeakers. Press the TO...

To set the minute, press and holdthe CLK control until CLOCK SETappears in the display and press theTUNE control: • to decrease minutes and • to increase minutes. The CLK control will allow you toswitch between media display mode(radio station, stereo information,etc.) and clock display mode (time)....

Volume/power control Press the control to turn the audiosystem on or off. Turn the control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition switch is turned back on. AM/FM s...

Tune adjust in radio mode • Press to move to the next frequency down the band(whether or not a listenablestation is located there). Hold thecontrol to move through thefrequencies quickly. • Press to move to the next frequency up the band (whether or not a listenable station is located there). Hold f...

2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns,indicating the station is held in memory on the control you selected. Bass adjust The bass adjust control allows youto increase or...

Speaker fade adjust Speaker sound can be adjustedbetween the front and rearspeakers. Tape select • To enter tape mode while in radiomode, press the TAPE AMScontrol. Automatic Music Search The Automatic Music Search featureallows you to quickly locate thebeginning of the tape selectionbeing played or...

Eject function Press the control to stop and eject atape. Dolby T noise reduction Dolby t noise reduction operates only in tape mode. Dolby t noise reduction reduces the amount ofhiss and static during tape playback. Press the control to activate (and deactivate) Dolby t noise reduction. Dolby t noi...

Tune adjust The tune control works in radio or CD changer mode. Tune adjust in radio mode • Press to move to the next frequency down the band(whether or not a listenablestation is located there). Hold thecontrol to move through thefrequencies quickly. • Press to move to the next frequency up the ban...

Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns,indicating the station is held in memor...

Bass adjust The bass adjust control allows youto increase or decrease the audiosystem’s bass output. Press the BASS control then press: • to decrease the bass output and • to increase the bass output. Treble adjust The treble adjust control allows youto increase or decrease the audiosystem’s treble ...

Press the FADE control then press: • to shift the sound to the front and • to shift the sound to the rear. Tape/CD select • To begin tape play (with a tapeloaded into the audio system)while in the radio or CD mode,press the TAPE control. Press thebutton during rewind or fast forward to stop the rewi...

• In the tape mode, tape direction will automatically reverse when theend of the tape is reached. • In CD mode, pressing the control fast forwards the CD within thecurrent track. Tape direction select Press SIDE 1–2 to play the alternateside of a tape. Eject function Press the EJ control to stop and...

Shuffle feature The shuffle feature operates in CDmode (if equipped) and plays alltracks on the current disc in randomorder. If equipped with the CDchanger, the shuffle featurecontinues to the next disc after all tracks on the current disc are played. Press the SHUFFLE control to start this feature....

• to decrease minutes and • to increase minutes. If your vehicle has a separate clockmodule, (other than the digital radiodisplay), the CLK button will notfunction in the above manner. The CLK button will allow you toswitch between media display mode(radio station, stereo information,etc.) and clock...

Premium AM/FM Stereo In Dash Six CD Radio Volume/power control Press the control to turn the audiosystem on or off. Turn the control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when the...

AM/FM select The AM/FM select control works inradio and CD modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press thecontrol to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in CD mode Press this control to stop CD play and begin radi...

Setting memory preset stations 1. Select the frequency band with the AM/FM select control. Press theAM/FM control to toggle between AM, FM1, or FM2. 2. Press the SEEK control to access the next listenable station up ordown the frequency band. Press the TUNE control to go up or down thelistening band...

Menu mode The MENU control allows you toaccess many different featureswithin your audio system. There arethree sets of menus available depending upon which mode or feature isactivated. While in FM mode, two menus are available. If RDS is turned off, youcan access the following: • SELECT HOURS — Refe...

Radio data system (RDS) feature This feature allows your audiosystem to receive text informationfrom RDS-equipped FM radiostations. To activate RDS: • When in FM mode, press the MENU control until RDS OFF displays. • Press the SEL control to engage this feature (RDS ON). RDS features: Once the RDS f...

use the SEEK or SCAN control to find the desired program type fromthe following selections: • Classic • Country • Info • Jazz • Oldies • R & B • Religious • Rock • Soft • Top 40 Show This feature allows you to select thetype of RDS broadcast informationthe radio will regularly show in thedisplay...

• OCCUPANCY MODE Use the SEL control to select thedesired signal mode (the selectedmode will appear in the display).The following signal modes can beselected: • DSP OFF—disengages the feature • NEWS—”voice-only” type of sound with a limited audio band • JAZZ CLUB—jazz club with clearly reflected sou...

Setting the clock Press the MENU control untilSELECT HOUR or SELECTMINUTE is displayed. Use the SEL control to manually setthe time. • Press to increase hours/minutes. • Press to decrease hours/minutes. Cleaning compact discs Inspect all discs for contamination before playing. If necessary, cleandis...

• Remove loose labels before inserting tapes. • Do not leave tapes in the cassette player for a long time when notbeing played. Radio frequency information The Federal Communications Commission (FCC) and the Canadian Radioand Telecommunications Commission (CRTC) establish the frequenciesAM and FM st...

SPEED CONTROL (IF EQUIPPED) To turn speed control on • Press ON. Vehicle speed cannot be controlleduntil the vehicle is traveling at orabove 48 km/h (30 mph). Do not use the speed control in heavy traffic or on roads thatare winding, slippery, or unpaved. Do not shift the gearshift lever into N (Neu...

You can accelerate with the accelerator pedal at any time during speedcontrol usage. Releasing the accelerator pedal will return your vehicle tothe previously programmed set speed. To set a lower set speed • Press and hold COAST. Releasethe control when the desiredspeed is reached or • Press and rel...

To disengage speed control • Depress the brake pedal or • Depress the clutch pedal (ifequipped). Disengaging the speed control willnot erase the previouslyprogrammed set speed. Pressing OFF will erase thepreviously programmed set speed. ON OFF Controls and features 71

Never adjust the steering wheel when the vehicle is moving. HAZARD FLASHER For information on the hazard flasher control, refer to Hazard flasher in the Roadside emergencies chapter. WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper controlto the desired interval, low or highspeed positio...

One touch down • Press AUTO completely down andrelease quickly. The driver’swindow will open fully. Depressagain to stop window operation. Window lock The window lock feature allows onlythe driver to operate the powerwindows. To lock out all the window controlsexcept for the driver’s press the lefts...

CHILDPROOF DOOR LOCKS When these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thedoors are unlocked. The childproof locks are located onrear edge of each rear door andmust be set separately for eachdoor. Setting the lock for one door...

2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the center position to lock mirrors in place. Fold-away mirrors Pull the side mirrors in carefully when driving through a narrow space,like an automatic car wash. The telescoping feature (if equipped) allows the mirror to ...

REMOTE ENTRY SYSTEM (IF EQUIPPED) This device complies with part 15 of the FCC rules and with RS-210 ofIndustry Canada. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) This devicemust accept any interference received, including interfe...

Sounding a panic alarm Press this control to activate thealarm. To deactivate the alarm, press thecontrol again or turn the ignition toACC or ON. Replacing the battery The transmitter is powered by one coin type three-volt lithium batteryCR2032 or equivalent. Typical operating range will allow you t...

Programming remote transmitters It is necessary to have ALL (maximum of four — original and/or new) of your remote transmitters available prior to beginning this procedure. To program the transmitters yourself: • Place the key in the ignition andturn from 2 (LOCK) to 3 (OFF)and cycle between 3 (OFF)...

TAILGATE LOCK (IF EQUIPPED) Your vehicle may be equipped with atailgate lock designed to preventtheft of the tailgate. • Insert ignition key and turn to theright to engage lock. • Turn ignition key to the left tounlock. TAILGATE REMOVAL Your tailgate is removable to allowmore room for loading. 1. Lo...

SEATING Full bench seat (if equipped) • Lift the track release bar to movethe seat forward or backward.Ensure that the seat is relatchedinto place. • Pull up on the release leverlocated at the bottom of theseatback to quickly fold theseatback forward. 40/20/40 split bench seat (if equipped) • Lift t...

Captain’s chair (if equipped) • Lift the track release bar to movethe seat forward or rearward.Make sure that the seat isrelatched into place. • Pull the release lever handlelocated on the side of the seat upto move the seat back forward orbackward. • Push down the release lever (ifequipped) located...

Press front to raise or lower thefront portion of the seat cushion. Press rear to raise or lower the rearportion of the seat cushion. Press the control to move the seatforward, backward, up or down. Using the manual lumbar support Turn the lumbar support controltoward the front of vehicle to movethe...

RETURNING THE SEAT TO SEATING POSITION Always be sure that the seat is in a latched position, whether theseat is occupied or empty. If not latched, the seat may cause injury during a sudden stop. 1. Pull control on the side of the seat to release seat cushion fromstorage position. 2. Push seat cushi...

Each seating position in your vehicle has a specific safety beltassembly which is made up of one buckle and one tongue that are designed to be used as a pair. 1) Use the shoulder belt on theoutside shoulder only. Never wear the shoulder belt under the arm.2) Never swing the safety belt around your n...

The front and rear outboard safety restraints in the vehicle arecombination lap and shoulder belts. The front passenger and rear seatoutboard safety belts have two types of locking modes described below: Vehicle sensitive mode The vehicle sensitive mode is the normal retractor mode, allowing freesho...

After any vehicle collision, the front passenger outboard seat beltsystem must be checked by a qualified technician to verify that the “automatic locking retractor” feature for child seats is stillfunctioning properly. In addition, all seat belts should be checked forproper function. BELT AND RETRAC...

Safety belt replacement label The short plastic boot on the frontsafety belt at the passengeroutboard anchor location covers a“Replace Belt” label on the safetybelt. In the event of a collision, thecolored label (REPLACE BELT)may become visible. If this occurs, the safety belt must be replaced. When...

Safety belt pretensioner Your vehicle may be equipped with safety belt pretensioners at the driverand front outboard passenger seating positions. The Seat Integrated Restraints (SIR) seat is equipped with a bucklepretensioner. Do NOT place objects between the seats, this couldinterfere with the func...

• Regular Cab and 4–door CrewCab • 4–door Super Cab (if equipped) Seating and safety restraints 95

To lower the shoulder belt height, push the button and slide the heightadjuster down. To raise the height of the shoulder belt, slide the heightadjuster up. Pull down on the height adjuster to make sure it is locked inplace. Position the shoulder belt height adjusters so that the belt restsacross th...

Belt minder The Belt Minder feature is a supplemental warning to the safety beltwarning function. This feature provides additional reminders to thedriver that the driver’s safety belt is unbuckled by intermittentlysounding a chime and illuminating the safety belt warning lamp in theinstrument cluste...

Reasons given... Consider... “Seat belts don’twork” Safety belts, when used properly, reduce risk of death to front seat occupants by 45% in cars, and by 60% in light trucks. “Traffic is light” Nearly 1 of 2 deaths occur in single-vehiclecrashes, many when no other vehicles are around. “Belts wrinkl...

Safety belt maintenance Inspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to make sure thereare no nicks, wears or cuts, replacing if necessary. All safety beltassemblies, including retractors, buckles, front seat belt buckle as...

Important supplemental restraint system (SRS) precautions The supplemental restraint systemis designed to work with the safetybelt to help protect the driver andright front passenger from certainupper body injuries. Air bags DO NOT inflate slowly orgently and the risk of injury from adeploying air b...

Do not put anything on or over the air bag module. Placingobjects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causingserious injury. Do not attempt to service, repair, or modify the Air BagSupplemental Restraint System or its ...

How does the air bag supplemental restraint system work? The air bag SRS is designed toactivate when the vehicle sustainssufficient longitudinal deceleration. The fact that the air bags did notinflate in a collision does not meanthat something is wrong with thesystem. Rather, it means the forceswere...

Disposal of air bags and air bag equipped vehicles (includingpretensioners) For disposal of air bags or air bag equipped vehicles, see your localdealership or qualified technician. Air bags MUST BE disposed of byqualified personnel. Passenger air bag ON/OFF switch (if equipped) An air bag ON/OFF swi...

In order to avoid inadvertent activation of the switch, alwaysremove the ignition key from the passenger air bag ON/OFF switch. Turning the passenger air bag back on The passenger air bag remains OFF until you turn it back ON. 1. Insert the ignition key and turnthe switch to ON. 2. The OFF light wil...

Always transport children who are 12 and younger in the rearseat. Always use safety belts and child restraints properly. If a child in a rear facing infant seat must be transported in front, thepassenger air bag must be turned OFF. This is because the back of the infant seat is too close to the infl...

• the child has a medical condition which, according to the child’sphysician, makes it necessary for the child to ride in the front seat sothat the driver can constantly monitor the child’s condition. 3. Medical condition. A passenger has a medical condition which, according to his or her physician:...

• although children age 12 and under ride in the rear seat wheneverpossible, children age 12 and under have no option but to sometimesride in the front seat because rear seat space is insufficient; or • the child has a medical condition that, according to the child’sphysician, makes it necessary for...

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant orchild restraint you might use. When possible, always place children under age 12...

SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child.Carefully follow all of the manufacturer’s instructions with the safety seatyou put in your vehicle. If you do not install and use the safety seatproperly, the ...

Ford recommends the use of a child safety seat having a top tetherstrap. Install the child safety seat in a seating position which is capableof providing a tether anchorage. For more information on top tetherstraps, refer to Attaching safety seats with tether straps. Carefully follow all of the manu...

Attaching safety seats with tether straps Some manufacturers make safety seats that include a tether strap thatgoes over the back of the vehicle seat and attaches to an anchoringpoint. Other manufacturers offer the tether strap as an accessory.Contact the manufacturer of your child safety seat for i...

The SuperCab rear seat has three straps behind the top of the seat backthat function as both routing loops for the tether straps and anchorloops. The tether strap anchors in your vehicle are in the following positions(shown from top view): Attach the tether strap only to the appropriate tether ancho...

Tether strap attachment 1. Position the child safety seat on the seat cushion. 2. Route the child safety seat tether strap over the back of the seat. 3. Locate the correct anchor for the selected seating position. 4. You may need to pull the seatback forward to access the tetheranchors. Make sure th...

If the safety seat is not anchored properly, the risk of a childbeing injured in a collision greatly increases. Tether strap attachment rear SuperCab only There are three loops of webbing just above the back of the rear seat(along the bottom edge of the rear window) in the SuperCab. Theseloops are t...

PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. Thissystem meets all Canadian Interference-Causing Equipment standardrequirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the ...

Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate. STARTING THE ENGINE 1. Turn the key to 5 (START)without pressing the acceleratorpedal and release as...

Using the engine block heater (if equipped) An engine block heater warms theengine coolant, which improvesstarting, warms up the engine fasterand allows the heater-defrostersystem to respond quickly. Use of anengine block heater is stronglyrecommended if you live in a regionwhere temperatures reach ...

WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or otherreproductive harm. In addition, certain fluids contained in vehicles andcertain products of component wear contain or...

steering control of your vehicle and, providing there is sufficientspace, will enable you to avoid obstacles and bring the vehicle to acontrolled stop. • The Anti-Lock system does not decrease the time necessary to applythe brakes or always reduce stopping distance. Always leave enoughroom between y...

The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released. Always set the parking brake fully and make sure that thegearshift is securely latched in P (Park) (automatic transmission) or in 1 (First) (manual t...

TRACTION-LOK AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly whenone wheel is on a poor traction surface. Under normal conditions, theTraction-Lok axle functions like a standard rear axle. Extended use of other than the manufacturer’s specified size tires on a...

Your vehicle has the capability to haul more cargo and people than mostpassenger cars. Depending upon the type and placement of the load,hauling people and cargo may raise the center of gravity of the vehicle. Use extra caution while becoming familiar with your vehicle. Know thecapabilities and limi...

If the parking brake is fully released, but the brake warning lampremains illuminated, the brakes may not be working properly. See your dealer or a qualified service technician. Driving with a 4–speed automatic transmission Understanding gearshift positions To put your vehicle in gear, start the eng...

(Overdrive) The normal driving position for thebest fuel economy. Transmissionoperates in gears one through four. (Overdrive) can be deactivated by pressing the transmission controlswitch (TCS) on the end of thegearshift lever. The transmission control indicatorlight (TCIL) (the word OFF) on theend ...

1 (First) Use 1 (Low) to provide maximumengine braking on steepdowngrades. Upshifts can be madeby shifting to 2 (Second) or to (Overdrive). Selecting 1 (Low) at higher speeds causes the transmission to shift to a lower gear, and willshift to 1 (Low) after vehicle decelerates to the proper speed. For...

When starting a vehicle with a manual transmission, you must: 1. Make sure the parking brake isfully set. 2. Depress the clutch pedal fully. 3. Put the gearshift lever in N(Neutral). 4. Turn the ignition to position 5(START) to start the engine, let theengine idle for a few seconds. 5. Depress the b...

Recommended shift speeds Downshift according to the following charts for your specificengine/drivetrain combination: Maximum downshift speeds 1 5-speed transmission Shift from: Transfer case position (if equipped) 2 2H or 4H 4L D (Overdrive) - 4 72 km/h (45 mph) 35 km/h (22 mph) 4 - 3 56 km/h (35 mp...

Parking your vehicle 1. Disengage the clutch, apply brakeand shift into N (Neutral). 2. Set parking brake. 3. Shift into 1 (First). 4. Turn the ignition key to position3 (OFF). 1 2 4 R 3 D 1 2 4 R L 3 D 3 2 1 5 4 Driving 136

Do not park your vehicle in Neutral, it may move unexpectedlyand injure someone. Use 1 (First) gear and set the parking brake fully. Reverse Make sure that your vehicle is at a complete stop before you shift into R(Reverse). Failure to do so may damage the transmission. Put the gearshift lever in N(...

Removing key from ignition • Turn the ignition key to position2. • Push the release lever forwardand rotate the key towards youand remove. POWER TAKE OFF (PTO) CAPABILITY (IF EQUIPPED) Some vehicles equipped with an automatic transmission and the 6.8L or7.3L engine are also equipped with Power Take ...

3. Place the gearshift lever in N (Neutral) (automatic transmission) ordepress the clutch (manual transmission). 4. Move the transfer case shift leverthrough N (Neutral) directly to 4L(4WD Low) and hold the shift leverin 4L (4WD Low) until the transfercase has fully engaged (up to 15seconds). 5. If ...

Do not leave the vehicle unattended with the transfer case in theN (Neutral) position. Always set the parking brake fully and turn off the ignition when leaving the vehicle. Using the electronic shift 4WD system (if equipped) Positions of the electronic shift system To prevent damage, the electronic...

Shifting from 4x4 HIGH (4WD high) to 2WD (2WD high) Rotate the 4WD control to 2WD atany forward speed. Disengagementof the transfer case and front hubsmay be delayed due to torque bindwhich is caused by driving on dryhard surfaces or performing tightturns while using the 4WD system. • You do not nee...

4. Move the 4WD control to the 4x4HIGH (4WD high) or 2WD (2WDhigh) position. 5. Hold the shift command until theLOW RANGE indicator light shutsoff. 6. If the LOW RANGE indicator light does not shut off after 15 seconds, start the vehicle moving, thenrepeat steps 1 through 5 beforereporting any shift...

When descending a steep hill, avoid sudden braking. Shift to a lower gearwhen added engine braking is desired. When speed control is on and you are driving uphill, your vehicle speedmay drop considerably, especially if you are carrying a heavy load. If vehicle speed drops more than 16 km/h (10 mph),...

The Safety Certification Label, found on the driver’s door pillar, listsseveral important vehicle weight rating limitations. Before adding anyadditional equipment, refer to these limitations. If you are adding weightto the front of your vehicle, (potentially including weight added to thecab), the we...

Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes aresafe if installed properly and adjusted to the manufacturer’sspecifications. The trailer brakes must meet local and Federalregulations. Do not connect a trailer’s hydraulic brake system directly to yourvehicle’s bra...

Servicing after towing If you tow a trailer for long distances, your vehicle will require morefrequent service intervals. Refer to your scheduled maintenance guide formore information. Trailer towing tips • Practice turning, stopping and backing up before starting on a trip toget the feel of the veh...

Read the following instructions before installing a snowplow: • Front GAWR must not exceed 63% of the GVW. Add ballast weight tothe back of the vehicle, if necessary. Refer to the Safety ComplianceCertification Label to find Front GAWR. • The Front Axle Accessory Reserve Capacity and the Total Acces...

Manual. Adherence to the toe and ride height specification isimportant for proper tire wear, ride, handling and headlight aim. Snowplowing with your air bag equipped vehicle Your vehicle is equipped with driverand passenger air bag SupplementalRestraint System (SRS). The SRS isdesigned to activate w...

GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford offers acomplimentary roadside assistance program. This program is separatefrom the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for the Basic warranty period (Canada) o...

The fuel pump shut-off switch islocated in the passenger’s foot well,by the kick panel. Use the following procedure to reset the fuel pump shut-off switch. 1. Turn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switc...

Always replace a fuse with one that has the specified amperagerating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color COLOR Fuse Rating Mini Fuses Standard Fuses Maxi Fuses Cartridge Maxi Fuses Fuse Link Cartridg...

Power distribution box The power distribution box, trailertow and electronic shift on the flyrelay blocks are located in theengine compartment near the brakemaster cylinder. The power distribution box contains high-current fuses that protect yourvehicle’s main electrical systems from overloads. Alwa...

The high-current fuses and relays are coded as follows. Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 7.5A * Trailer Tow Left Stop/Turn Lamp 2 10A* Washer Pump 3 7.5A* Trailer Tow Right Stop/Turn Lamp 4 20A* Trailer Tow Backup Lamps, Trailer TowPark Lamps 5 20A* (Gasoline ...

Spare tire information Your vehicle may be equipped with a spare tire that can be used aseither a spare or a regular tire. The spare tire is not equipped with wheeltrim. The wheel trim from the original wheel/tire may be used on thespare. If your vehicle is equipped with 4WD, a spare tire of a diffe...

• one wheel nut wrench. Slide oversquare end of jack handle. 2. If equipped, unlock and remove the spare tire lock from the rearbumper drive tube using the the spare tire lock key and the jack handle. 3. Insert the hooked end of the jackhandle into the rear bumper drivetube. The handle will stop mov...

Stowing the spare tire 1. Lay the tire on the ground with the valve stem facing up. 2. Slide the wheel under the vehicleand install the retainer through thewheel center. 3. Turn the jack handle clockwiseuntil the tire is raised to its originalposition underneath the vehicle. Theeffort to turn the ja...

To prevent the vehicle frommoving when you change a tire, be sure the parking brake isset, then block (in bothdirections) the wheel that isdiagonally opposite (other sideand end of the vehicle) to the tirebeing changed. 2. Turn engine OFF and block the diagonally opposite wheel (block notprovided). ...

The following steps apply to F250/F350 only: 6. Insert the hooked end of the jackhandle into the jack and use thehandle to slide the jack under thevehicle. 7. Position the jack according to thefollowing guides: • Front (4x2) Roadside emergencies 175

• Front passenger side (4x4) • Front driver side (4x4) Make sure the jack fits into thenotched area on the differentialhousing. • Rear Roadside emergencies 176

8. Turn the jack handle clockwiseuntil the wheel is completely off theground and high enough to installthe spare tire. 9. Remove the lug nuts with the lugwrench. 10. On single rear wheel vehicles,replace the flat tire with the sparetire, making sure the valve stem isfacing outward for all front tire...

The following steps apply to all vehicles: 19. Remove the jack and fully tightenthe lug nuts in the order shown. 20. Stow the flat tire. Refer to Stowing the spare tire if the vehicle is equipped with a spare tire carrier. 21. Stow the jack, jack handle andlug wrench. Make sure the jack issecurely f...

Do not attempt to push start your vehicle. Automatic transmissionsdo not have push-start capability. Preparing your vehicle When the battery is disconnected or a new battery is installed, thetransmission must relearn its adaptive strategy. As a result of this, thetransmission may shift firmly. This ...

2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery. 3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s eng...

Do not connect the end of the second cable to the negative (-)terminal of the battery to be jumped. A spark may cause an explosion of the gases that surround the battery. 5. Ensure that the cables are clear of fan blades, belts, moving parts ofboth engines, or any fuel delivery system parts. Jump st...

2. Remove the jumper cable on the negative (-) connection of thebooster vehicle’s battery. 3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle...

When the battery is disconnected or a new battery is installed, thetransmission must relearn its adaptive strategy. As a result of this, thetransmission may shift firmly. This operation is considered normal andwill not effect function or durability of the transmission. Over time, theadaptive learnin...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a scheduled maintenance guide which makes trackingroutine service easy. If your vehicle requires professional service, your dealership can providethe...

3. Turn off the engine and remove the key. 4. Block the wheels to prevent the vehicle from moving unexpectedly. Working with the engine on • Automatic transmission: 1. Set the parking brake and ensure the gearshift is securely latched in P(Park). 2. Block the wheels to prevent the vehicle from movin...

OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel. 2. Go to the front of the vehicle andrelease the auxiliary latch locatedunder the right center of the hood.Slide the handle to release theauxiliary latch. 3. Lift the hood ...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 5.4L V8/6.8L V10 gasoline engines Refer to the 7.3 Liter Power Stroke Direct Injection Turbo Diesel Owner’s Guide Supplement for diesel engine component locations. 1. Engine oil dipstick 2. Clutch fluid reservoir (manual transmission) 3. Brake fluid r...

ENGINE OIL Checking the engine oil Refer to the scheduled maintenance guide for the appropriate intervalsfor checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into theoil pan. 3. Set the parking brake and ensure t...

• If the oil level is below the MINmark, add enough oil to raise thelevel within the MIN-MAX range. • Oil levels above the MAX mark may cause engine damage. Some oilmust be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil ...

BRAKE FLUID Checking and adding brake fluid—gasoline engine Brake fluid should be checked andrefilled as needed. Refer to thescheduled maintenance guide forthe service interval schedules. 1. Clean the reservoir cap beforeremoval to prevent dirt or waterfrom entering the reservoir. 2. Visually inspec...

Checking and adding brake fluid—diesel engine Check and refill the Hydromaxbrake fluid reservoir using thefollowing procedure. Refer to thescheduled maintenance guide forthe service interval. 1. Clean the reservoir caps beforeremoval to prevent dirt or waterfrom entering the reservoir. 2. Visually i...

WINDSHIELD WASHER FLUID Washer fluid Check the washer fluid wheneveryou stop for fuel. The reservoir ishighlighted with a symbol. If the level is low, add enough fluidto fill the reservoir. In very coldweather, do not fill the reservoir allthe way. Only use a washer fluid that meets Ford specificati...

When the engine is cold, check thelevel of the engine coolant in thereservoir. • The engine coolant should be at the “cold fill level” or within the “coldfill range” as listed on the engine coolant reservoir (depending uponapplication). • Refer to the scheduled maintenance guide for service interval...

Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. The cooling system in your vehicle is filled with green-colored MotorcraftPremium Engine Coolant meeting Ford Specification ESE-M97B4...

system may have a leak. Operating an engine with a low level of coolantcan result in engine overheating and possible engine damage. Recycled engine coolant Ford Motor Company recommends the use of a recycled engine coolantproduced by Ford-approved processes in vehicles originally equippedwith Motorc...

What you should know about fail-safe cooling (if equipped) If the engine coolant supply is depleted, this feature allows the vehicle tobe driven temporarily before incremental component damage is incurred.The “fail-safe” distance depends on ambient temperatures, vehicle loadand terrain. How fail-saf...

4. Check the coolant level and replenish if low. Never remove the coolant reservoir cap while the engine isrunning or hot. 5. Re-start the engine and take your vehicle to a service facility. Driving the vehicle without repairing the engine problemincreases the chance of engine damage. Take your vehi...

3. While the engine idles, turn the steering wheel left and right severaltimes. 4. Turn the engine off. 5. Recheck the fluid level on the dipstick. Do not add fluid if the level isbetween the arrows in the FULL COLD range. 6. If the fluid is low, add fluid in small amounts, continuously checkingthe ...

Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used. The type offluid used is normally indicated on the dipstick and also in the Lubricant specifications section in the Capacities and specifications chapter. Use of a non-approved automatic transm...

3. Fluid level should be at bottom ofthe opening. 4. Add enough fluid through thefiller opening so that the fluid levelis at the bottom of the opening. 5. Install and tighten the fill plugsecurely. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter. Che...

AIR FILTER MAINTENANCE Refer to the scheduled maintenance guide for the appropriate intervalsfor changing the air filter element. When changing the air filter element, use only the Motorcraft air filterelement listed. Refer to Motorcraft Part Numbers in the Capacities and specifications chapter. Do ...

For longer, trouble-free operation, keep the top of the battery clean anddry. Also, make certain the battery cables are always tightly fastened tothe battery terminals. If you see any corrosion on the battery or terminals, remove the cablesfrom the terminals and clean with a wire brush. You can neut...

the engine must relearn its idle and fuel trim strategy for optimumdriveability and performance. To begin this process: 1. With the vehicle at a complete stop, set the parking brake. 2. Put the gearshift in P (Park) (automatic transmission) or the neutralposition (manual transmission), turn off all ...

detergent. Rinse thoroughly with clean water. To avoid damaging theblades, do not use fuel, kerosene, paint thinner or other solvents. Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from thewindshield and lock into the serviceposition. 2. Turn the blade at an angle...

SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has beenparked for at least one hour or has been driven less than 5 km (3miles). • Adjust tire pressure to recommended specifications found on theCe...

• Five tire rotation Replacing the tires Replace the tires when the wearband is visible through the tiretreads. When replacing full size tires, never mix radial bias-belted, orbias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same s...

Do not replace your tires with “high performance” tires or largersize tires. Failure to follow these precautions may adversely affect thehandling of the vehicle and make it easier for the driver to lose control and roll over. Tires that are larger or smaller than your vehicle’s original tires may al...

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tankmay cause leakage and lead to fuel spray and fire. The fuel system may be under pressure. If the fuel filler cap isventing vapor or if you hear a hissing sound, w...

Many of the world’s automakersissued the World-wide Fuel Charterthat recommends gasolinespecifications to provide improvedperformance and emission controlsystem protection for your vehicle.Gasolines that meet the World-wideFuel Charter should be used whenavailable. Ask your fuel supplierabout gasoli...

5. Turn the filler cap clockwise 1/8 of a turn until it stops. If the “Service Engine Soon/Check Engine” indicator comes on and stayson after you start the engine, the fuel filler cap may not be properlyinstalled. Turn off the engine, remove the fuel filler cap, align the capproperly and reinstall i...

Filling the tank The advertised fuel capacity of the fuel tank on your vehicle is equal tothe rated refill capacity of the fuel tank as listed in the Refill Capacities section of the Capacities and specifications chapter. The advertised capacity is the amount of the indicated capacity and theempty r...

5. Follow one of the simple calculations in order to determine fueleconomy: Multiply liters used by 100, then divide by total kilometerstraveled. Divide total miles traveled by total gallons used. Keep a record for at least one month and record the type of driving (cityor highway). This will provide...

Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fueleconomy. • Use recommended engine oil. Refer to Lubricant Specifications. • Perform all regularly scheduled maintenance items. Follow therecommended mainte...

EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to comply with applicableexhaust emission standards. To make sure that the catalytic converter andother emission control components continue to work prope...

Please consult your “Warranty Guide” for complete emission warrantyinformation. Readiness for Inspection/Maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test ofthe on-board diagnostics system. If your “Check Engine/Service EngineSoon” light is on, refer to ...

Replacing headlamp bulbs (aerodynamic) 1. Make sure that the headlamp control is in the OFF position. 2. Open the hood. 3. Disconnect the electrical connector from the bulb by pulling rearward. 4. Remove bulb retainer ring byturning it counterclockwise, thenslide the ring off the plastic base. 5. Wi...

Replacing front parking/turn signal bulbs 1. Make sure headlamp switch is in OFF position. 2. Open the hood. 3. Remove the two screws andcarefully disengage parkinglamp/turn signal assembly from thevehicle. 4. Rotate bulb socketcounterclockwise about 1 ⁄ 4 turn and remove from lamp assembly. 5. Care...

Replacing brake/tail/backup lamp bulbs — F450/F550 only The brake/tail/backup lamp bulbsare located in the same portion ofthe tail lamp assembly. Follow thesame steps to replace either bulb: 1. Remove the four screws and thelamp lens from lamp assembly. 2. Carefully pull the bulb straightout of the ...

Replacing roof marker bulbs To change the cab marker bulbs: 1. Remove the screw and lens fromthe lamp assembly. 2. Carefully pull the bulb straightout of the socket and push in thenew bulb. 3. Install lens on lamp assembly withscrew. Replacing foglamp bulbs (if equipped) 1. Remove the bulb socket fr...

Washing your vehicle Wash your vehicle regularly withcold or lukewarm water. Never usestrong detergents or soap. If yourvehicle is particularly dirty, use aquality car wash detergent. Alwaysuse a clean sponge, washing gloveor similar device and plenty of waterfor best results. To avoid spots,avoid w...

Avoid getting wax on the windshield, or on any surfaces which appearcoarse or bumpy. If you have wax applied at a commercial car wash, it isrecommended that you clean the wiper blades and windshield asdescribed in Cleaning the wiper blades and windshield. Repairing paint chips Minor scratches or pai...

Cleaning non-painted plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover ifnecessary. Do not clean plastic parts with thinners, solvents orpetroleum-based cleaners. Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. Ifnecessa...

Cleaning the instrument panel Clean with a damp cloth, then dry with a dry cloth. Avoid cleaner or polish that increases the gloss of the upper portion ofthe instrument panel. The dull finish in this area helps protect the driverfrom undesirable windshield reflection. Do not use chemical solvents or...

MOTORCRAFT PART NUMBERS Component* 5.4L V8 engine 6.8L V10 engine Air filter element FA-1634 FA-1634 Fuel filter FG-986B FG-986B Oil filter FL-820-S FL-820-S PCV valve EV-233 EV-233 Battery (Standard) BXT-65-650 BXT-65-650 Battery (Optional) BXT-65-750 BXT-65-750 Spark plugs-platinum** AWSF-22W AWSF...

LUBRICANT SPECIFICATIONS Item Ford partname orequivalent Ford partnumber Fordspecification Front axle(4X4) Motorcraft SAE75W-90Premium 4x4Front AxleLubricant XY-75W90-TQL WSP-M2C201-A Rear axle Motorcraft SAE75W-140 HighPerformanceSynthetic RearAxle Lube 1 F1TZ-19580-B WSL-M2C192-A Motorcraft SAE80W...

2 Ensure the correct automatic transmission fluid is used. Transmission fluid requirements are indicated on the dipstick or on the dipstickhandle. Check the container to verify the fluid being added is of thecorrect type. Refer to your scheduled maintenance guide to determinethe correct service inte...

F350–except Crew Cab Dimension Body style ChassisCab RegularCab Super Cab4x2 Super Cab4x4 (1) Overallheight 1 972 mm(77.6 in) 1 860 mm(73.2 in) c,e 1 865 mm(73.4 in) a 1 861 mm(73.6 in) b 1 960 mm(77.2 in) (2) Track(Front / Rear) 1 736.3 mm(68.3 in) /1 879.6 mm(74.0 in) 1 736.3 mm(68.3 in) /1 729.3 ...

F350-Crew Cab Dimension Body style Crew Cab 4x2 Crew Cab 4x4 (1) Overall height 1 929 mm (75.9 in) 2 038 mm (80.2 in) (2) Track(Front / Rear) 1 745 mm (68.7 in)/1 729 mm (68.1 in) a,b 1 736 mm (68.4 in)/1 729 mm (68.1 in) a,b (3) Overall width 1 988 mm (78.3 in) a,b 2 077 mm (79.0 in) a,b (4) Wheelb...

Ford Extended Service Plan You can get more protection for your new car or light truck bypurchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESPis an optional service contract which is backed by Ford Motor Companyor Ford Motor Service Company (in the U.S.) and Ford of Canada (inCanada). ...

If you have questions or concerns, or are unsatisfied with the service youare receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at yourselling/servicing dealership. 2. If your inquiry or concern remains unresolved, contact the SalesManager or Service Manager at t...

replacement or repurchase remedies provided by certain state laws. Thisdispute handling procedure is not required prior to enforcing statecreated rights or other rights which are independent of theMagnuson-Moss Warranty Act or state replacement or repurchase laws. THE DISPUTE SETTLEMENT BOARD (U.S. ...

Concerns are ineligible for review if the New Vehicle Limited Warrantyhas expired at receipt of your application and, in certain states eligibilityis dependent upon the customer’s possession of the vehicle. Eligibility may differ according to state law. For example, see the uniquebrochures for Calif...

• a brief summary of the action taken by the dealer(s) and Ford MotorCompany • the names (if known) of all the people you contacted at thedealership(s) • a description of the action you expect to resolve your concern You will receive a letter of explanation if your application does notqualify for Bo...

You may also contact the North American Customer Relationship Centerat 1-800-392-3673 (Ford), TDD for the hearing impaired: 1-800-232-5952or by writing to the Center at the following address: Ford Motor CompanyCustomer Relationship Center16800 Executive Plaza DriveP.O. Box 6248Dearborn, Michigan 481...

The use of leaded fuel in your vehicle without proper conversion maydamage the effectiveness of your emission control system and may causeengine knocking or serious engine damage. Ford Motor Company/Ford ofCanada is not responsible for any damage caused by use of improperfuel. In the United States, ...

Protection and appearance equipment Air bag anti-theft locks All weather vinyl floor mats Bed mat/bedliner tailgate covers Bed hooks Bed mats Bedliners Brush guard Carpet floor mats Cleaners, waxes and polishes Diamond plate bed rail caps Diamond plate front box protection Diamond plate splash guard...

ORDERING ADDITIONAL OWNER’S LITERATURE To order the publications in this portfolio: Make checks payable to: HELM, INCORPORATEDP.O. Box 07150Detroit, Michigan 48207 For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST,for credit card holders only Obt...

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle hasa defect that could cause a crash, orcould cause injury or death, youshould immediately inform theNational Highway Traffic SafetyAdministration (NHTSA) in additionto notifying Ford Motor Company. If NHTSA receives similar compl...

A Accessory delay ..........................75 Air bag supplementalrestraint system ................101–102 and child safety seats ............103description ..............................102disposal ....................................106driver air bag ..........................104indicator light ....

Load limits .................................147 GAWR ......................................147GVWR ......................................147trailer towing ..........................147 Loading instructions .................149 Locks childproof ..................................76 Lubricant specific...

W Warning chimes .....................14–15 Warning lights (see Lights) .......10 Washer fluid ..............................197 Water, Driving through .............150 Windows power .........................................74 Windshield washer fluid andwipers checking and adding fluid .....197check...

Item Information Required fuel Unleaded fuel only - 87 octane Fuel tank capacity Refer to Refill capacities in the Capacities and specifications chapter. Engine oil (includesfilter change) 5.7L (6.0 quarts). Use Motorcraft SAE 5W-20Super Premium Motor Oil, Ford specificationWSS-M2C153-H. Tire size a...

fluid. However, these dual usage fluids may be used in transmissions thatrequire the MERCON t V type fluid. MERCON t and MERCON t V type fluids are not interchangeable. DO NOT mix MERCON t and MERCON t V. Use of a transmission fluid that indicates dual usage (MERCON t and MERCON t V) in an automatic...