Ford 2000 Taurus- Manuals

WARNING LIGHTS AND CHIMES Turn signal Illuminates when the left or rightturn signal or the hazard lights areturned on. If one or both of theindicators stay on continuously orflash faster, check for a burned-outturn signal bulb. Refer to Exterior bulbs in the Maintenance and care chapter. High beams ...

Safety belt Momentarily illuminates when theignition is turned to the ON positionto remind you to fasten your safetybelts. For more information, refer tothe Seating and safety restraints chapter. Door ajar Illuminates when the ignition is inthe ON or START position and anydoor is open. Service engin...

3. The fuel cap may not have been properly installed and securelytightened. These temporary malfunctions can be corrected by filling the fuel tankwith high quality fuel of the recommended octane and/or properlyinstalling and securely tightening the gas cap. After three driving cycleswithout these or...

stays on, you should check the coolant level inside the reservoir. Forinstructions on adding coolant, see Engine coolant in the Maintenance and care chapter. Anti-theft system (if equipped) Refer to Perimeter alarm system (if equipped) and SecuriLock y passive anti-theft system in the Controls and f...

Brake system warning Momentarily illuminates when theignition is turned to the RUNposition. Also illuminates if theparking brake is engaged. If thebrake warning lamp does notilluminate at these times, or remains on after releasing the parking brake,seek service immediately. One of the following cond...

Safety belt warning chime Sounds to remind you to fasten your safety belts. For information on the safety belt warning chime, refer to the Seating and safety restraints chapter. Supplemental restraint system (SRS) warning chime For information on the SRS warning chime, refer to the Seating and safet...

Tachometer Indicates the engine speed inrevolutions per minute. Driving with your tachometerpointer continuously at the top ofthe scale may damage the engine. Engine coolant temperature gauge Indicates the temperature of theengine coolant. At normal operatingtemperature, the needle remainswithin the...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parkinglamps. Rotate to the second positionto also turn on the headlamps. Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the ignition must be in the ON position an...

PANEL DIMMER CONTROL Use to adjust the brightness of theinstrument panel during headlampand parklamp operation. • Rotate up to brighten. • Rotate down to dim. • Rotate to full up position (pastdetent) to turn on interior lamps. The dome lamp will not illuminate if the panel dimmer/dome lampcontrol i...

Activating the rear window defroster will also activate the heated mirrors(if equipped). For more information refer to Heated Outside Mirrors in this section. CLIMATE CONTROL SYSTEM Manual heating and air conditioning system (if equipped) Fan speed control Controls the volume of air circulatedin the...

Mode selector control Controls the direction of the airflowto the inside of the vehicle. The air conditioning compressor willoperate in all modes except(Panel) and (Floor). However, the air conditioning will only function ifthe outside temperature is about10°C (50°F) or higher. Since the air conditi...

• (Floor)-Allows for maximum heating by distributing outside air through the floor ducts. However, the air will not be cooled below theoutside temperature because the air conditioning does not operate inthis mode. • (Floor and defrost)-Distributes outside air through the windshield defroster ducts a...

Turning the EATC on Press AUTO, any of the override controls or the fan speed control. TheEATC will only operate when the vehicle is running. Turning the EATC off Press OFF. The OutsideTemperature function will continueto operate until the ignition isturned off. Automatic operation Press AUTO and se...

Temperature selection The display window indicates theselected temperature, function(AUTO or one of the overridecontrols) and manual control of fanspeed ( ) if automatic fan speed is not desired. To control the temperature, selectany temperature between 18°C(65°F) and 29°C (85°F) by pressingthe temp...

Fan speed ( ) When AUTO is pressed, fan speed isadjusted automatically for existingconditions. You can override fanspeed at any time. To control fanspeed manually, press the fancontrol to cancel automatic fanspeed operation. Press the controlup for higher fan speed or down forlower fan speed. The di...

The air conditioning compressor can operate in all modes exceptand . It will also operate only when required when AUTO has been selected. However, the air conditioning will only function if the outsidetemperature is about 10°C (50°F) or higher. Since the air conditioner removes considerable moisture...

• MAX A/C-Uses recirculated air to cool the vehicle. The temperaturewill remain unchanged and air will be cooled based on the selectedtemperature. To exit, press AUTOMATIC or any other overridecontrols. MAX A/C is noisier than normal A/C but more economicaland will cool the inside of the vehicle fas...

• Remove any snow, ice or leavesfrom the air intake area (at thebottom of the windshield). • If your vehicle has been parked with the windows closed during hotweather, the air conditioner will do a much faster job of cooling if youdrive for two or three minutes with the windows open. This will force...

USING YOUR AUDIO SYSTEM AM/FM Stereo Volume/power control Press the control to turn the audiosystem on or off. Turn control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when the Controls...

Scan function The scan function works in radiomode. Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stationson the frequency band. Press the control again to stop the scan mode. Radio station memory preset The radio is equipped with six station memory pr...

MACH T Audio System with AM/FM Stereo/Cassette Volume/power control Press the control to turn the audiosystem on or off. Turn control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when th...

AM/FM select The AM/FM select control works inradio, tape and CD modes (ifequipped). Press the AM or FMcontrol to enter into radio mode. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press thecontrol to switch between AM, FM1 or FM2 memory preset stations. Pr...

Scan function in CD mode Press the SCAN control to hear a short sampling of all selections on theCD. (The CD scans in a forward direction, wrapping back to the firsttrack at the end of the CD.) To stop on a particular selection, press thecontrol again. Radio station memory preset The radio is equipp...

2. Press to eject the magazine. 3. Turn the magazine (A) over. 4. Using the disc holder releaseknob (C), pull the disc holder (B)out of the magazine. If you pull too hard on the disc holder, the disc holder may comecompletely out of the magazine. If this happens, reinsert the disc holderback into th...

5. Line up the CD with the grooveof the disc holder. Ensure that thelabel on the CD faces downwards. 6. Press in on the disc holder until itlocks securely into the magazine. Ifthe disc holders are not fully lockedinto the magazine, the unit will notoperate. Ensure that the disc holder isevenly inser...

Radio frequency information The Federal Communications Commission (FCC) and the Canadian Radioand Telecommunications Commission(CRTC) establish the frequenciesAM and FM stations may use for their broadcasts. Allowable frequenciesare: AM 530, 540–1600, 1610 kHz FM 87.7, 87.9–107.7, 107.9 MHz Not all ...

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) Press and hold the rocker control(located on the side of the driver’sseat) to adjust accelerator andbrake pedal. • press the rear side of the controlto adjust the pedals toward you • press the front side of the control to adjust the pedals away from you The...

SPEED CONTROL (IF EQUIPPED) To turn speed control on • Press ON. Vehicle speed cannot be controlleduntil the vehicle is traveling at orabove 48 km/h (30 mph). Do not use the speed control in heavy traffic or on roads thatare winding, slippery, or unpaved. Do not shift the gearshift lever into N (Neu...

To disengage speed control • Depress the brake pedal. Disengaging the speed control willnot erase the previouslyprogrammed set speed. Pressing OFF will erase thepreviously programmed set speed. To return to a previously set speed • Press RES/RSM/RESUME. ForRES/RSM/RESUME to operate,the vehicle speed...

Rear window wiper and washer (wagon only) The rear wiper control is locatedunder the headlamp controls Pressthe wiper control to activate therear wiper. Press again to turn offthe wiper. Press the washer control to activatethe rear washer. The wiper willcome on when the washer control ispressed, if ...

TILT STEERING Pull the tilt steering control towardyou to move the steering wheel upor down. Hold the control whileadjusting the wheel to the desiredposition, then release the control. Never adjust the steering wheel when the vehicle is moving. DOME LAMPS AND MAP LAMPS The front dome lamp is located...

ILLUMINATED VISOR MIRROR (IF EQUIPPED) To turn on the visor mirror lamps,lift the mirror cover. Adjust theamount of light by sliding thecontrol. MOON ROOF (IF EQUIPPED) To open, press and hold the rearportion of the control. This will fullyopen the moon roof. To close, press and hold the frontportio...

You will need a Phone Adapter System (PAS) that is compatible withyour cell phone that you install into the center console. This systemincludes a Phone Adapter Module (PAM) with a Wiring Harness and aHang-Up Cup. For more information, call 1–800–736–9450 to order thePhone Adapter System (PAS) for yo...

POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of therocker switch to close. • Press the bottom portion of therocker switch to open. One touch down • Press AUTO completely down tothe second detent. The driver’swindow will open fully. Depressup to ...

POWER SIDE VIEW MIRRORS To adjust your mirrors: 1. Select to adjust the left mirror or to adjust the right mirror. 2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the center position to disable adjust function. Heated outside mirrors (if equipped) Both mirrors are heate...

CENTER CONSOLE Your vehicle may be equipped with a variety of console features. Theseinclude: • Utility compartment • Bin mat (snap-in) • Cupholders (front and rear) • Coin holder slots • Compact disc changer (if equipped) • Tissue holder • Rear A/C vent • Rear ashtray (see your Ford, Lincoln Mercur...

TRUNK REMOTE CONTROL Press the remote trunk releasecontrol on the instrument panel tothe left of the steering wheel. LIFTGATE (WAGON ONLY) You can open and close the liftgate and the liftgate window from outsidethe vehicle. It cannot be opened from inside the cargo area. • To open the liftgate windo...

CARGO AREA FEATURES Storage compartment Your vehicle comes equipped with astorage compartment in the floor ofthe cargo area. An additionalcompartment is in the rear trimpanel on the right. Always put theload you are carrying as far forwardas possible. Cargo net (if equipped) (Wagon) The cargo net se...

To prevent the possibility of injuries, the fasteners for the cargoarea cover must be properly attached to the mounting clips on the rear trim panels. Do not place any objects on the cargo area cover. They mayobstruct your vision or strike occupants of the vehicle in the case of a sudden stop or col...

7. Insert the shade into the side mounting brackets and check to makesure that it operates properly. The cover may cause injury in a sudden stop or accident if it isnot securely installed. Cargo utility hooks (Sedan) The utility hooks located in side the trunk can be used to hang smallitems on. Do n...

Changes or modifications not expressly approved by the partyresponsible for compliance could void the user’s authority tooperate the equipment. Illuminated entry The interior lamps illuminate when the remote entry system is used tounlock the door(s). The system automatically turns off after 25 secon...

To program the transmitters yourself: • Insert a key in the ignition andturn from 3 (OFF) to 4 (ON)eight times in rapid succession(within 10 seconds) with theeighth turn ending in the 4 (ON)position. The doors willlock/unlock to confirm thatprogramming mode has beenentered. • Within 20 seconds, prog...

To replace the battery: 1. Twist a thin coin between the twohalves of the transmitter near thekey ring. DO NOT TAKE THEFRONT PART OF THETRANSMITTER APART. 2. Place the positive (+) side of newbattery in the same orientation.Refer to the diagram inside thetransmitter unit. 3. Snap the two halves back...

• Press 7/8 and 9/0 controls on thekeyless entry pad at the sametime to lock the doors (doorsopened or closed). • Open a door and press the power door lock control to lock the doors. There is a 20 second countdown when any of the above actions occurbefore the vehicle becomes ARMED. Each door/hood or...

Disarming the system You can disarm the system by any of the following actions: • Unlock the doors by using yourremote entry transmitter. • Unlock the doors by using yourkeyless entry pad. • Unlock the doors or liftgate with a key. Turn the key full travel(toward the front of the vehicle) to make su...

KEYLESS ENTRY SYSTEM (IF EQUIPPED) With the keyless entry keypad, youcan: • lock or unlock the vehicle doorsand liftgate (wagons) without using the key • open the trunk • arm and disarm the perimeter alarm system (if equipped) See also Remote entry system and Perimeter alarm system in this chapter f...

To exit, press 7/8 and 9/0 simultaneously or allow more than 5 secondsto elapse since a button press occured and the 5 digit keycode will beprogramed. If you wish to erase your personal code, use the following instructions: Erasing personal code 1. Enter the factory-set code. 2. Press 1/2 within fiv...

3. To unlock the trunk or liftgate(wagon), enter the five-digitfactory-set code, then press the 5/6control within five seconds. Locking the doors and liftgate(wagon), press the 7/8 and 9/0controls at the same time. This canbe done at any time. Autolock Autolock is a feature that will automatically l...

Deactivating/activating horn chirp There are 2 methods to enable/disable this feature. One through yourdealer and the second with a door lock sequence using the followinginstructions: 1. Turn the ignition key to RUN, then press the door UNLOCK controlbutton 3 times. 2. Turn the ignition key to OFF, ...

momentary problem if they are too close to the key during engine start.If a problem occurs, turn the ignition OFF and restart the engine with allother objects on the key ring held away from the ignition key. Check tomake sure the encoded ignition key is an approved Ford encodedignition key. Spare Se...

2. Turn ignition to OFF and remove the first SecuriLock y key from the ignition. 3. Within five seconds of turning the ignition to OFF, insert the secondpreviously programmed SecuriLock y key into the ignition and turn the ignition from OFF to ON (maintain ignition in ON for at least one secondbut n...

SEATING Adjustable head restraints Your vehicle’s seats are equipped with head restraints which arevertically adjustable. The purpose of these head restraints is to help limithead motion in the event of a rear collision. To properly adjust your headrestraints, lift the head restraint so that it is l...

Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. Reclining the seatback can reduce the effectiveness of the seat’ssafety belt in the event of a collision. Lift handle to move seat forward orbackward. Pull lever up to adjust seatback. Adjusting the front ...

Reclining the seatback can reduce the effectiveness of the seat’ssafety belt in the event of a collision. The control is located on the outboard side of the seat cushion. Press front to raise or lower thefront portion of the seat cushion. Press rear to raise or lower the rearportion of the seat cush...

REAR SEATS 2nd seat/Split-folding rear seat (if equipped) One or both rear seatbacks can be folded down to provide additionalcargo space. To lower the seatback(s) frominside the vehicle, pull tab to releaseseat back and then fold seatbackdown. When raising the seatback(s), make sure you hear the sea...

3. Lift the remote latch release onthe left side of the compartmentand fold the remaining floor paneluntil it latches. Make sure theseatback is locked in the uprightposition. To close the seat, make sure the safety belts are properly stowed, thenlift the remote latch release and push the seat down u...

• The electrical wiring for the air bags, crash sensor(s), safety beltpretensioners, front safety belt usage sensors and driver’s seat positionsensor. How does the personal safety system work? The Personal Safety System uses a collection of sensors to gatherinformation about the driver’s seat positi...

• The indicator light will not illuminate immediately after ignition isturned on. • A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and indicator light are repaired. If any of these things happen, even intermittently, have the PersonalSafety System se...

All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even when an air bag SRS is provided. It is extremely dangerous to ride in a cargo area, inside oroutside of a vehicle. In a collision, people riding in these areas are more likely to be seriously inju...

2. To unfasten, push the releasebutton and remove the tongue fromthe buckle. The front and rear outboard safety restraints in the vehicle arecombination lap and shoulder belts. The front passenger and rear seatoutboard safety belts have two types of locking modes described below: Energy management r...

BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED ifthe seat belt assembly “automatic locking retractor” feature or any other seat belt function is not operating properly when checkedaccording to the procedures in Workshop Manual. Failure to replace the Belt and Retractor assembly couldincrease the risk ...

After any vehicle collision, the seat belt system at all outboardseating positions (except driver, which has no “automatic locking retractor” feature) must be checked by a qualified technician to verifythat the “automatic locking retractor” feature for child seats is stillfunctioning properly. In ad...

The Personal Safety System provides the most benefit to beltedoccupants. The system monitors and tailors the air bag deployment based upon safety belt usage. Failure to properly wearyour safety belt will increase your risk of injury. Front safety belt height adjustment Your vehicle has safety belt h...

Lap belts Adjusting the lap belt The lap belt does not adjust automatically. The lap belts should fit snugly and as low as possible around thehips, not around the waist. Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn...

Safety belts for rear-facing occupants (wagon only) Never use child safety seats in the third seat of a wagon. Your vehicle is equipped with safety belts containing an adjust tongue atthe rear-facing seating positions. When the adjust tongue of the lap/shoulder combination seat belt is latchedinto t...

One time disable Anytime the safety belt is buckled and then unbuckled during an ignitionON cycle, Belt Minder will be disabled for that ignition cycle only. Thesafety belt needs to be latched for a minimum of 3 seconds before beltminder is disabled. Deactivating/activating the belt minder feature R...

• After step 5 the safety belt warning light will be turned on for threeseconds. 6. Within seven seconds of the safety belt warning light turning off,buckle then unbuckle the safety belt. • This will disable Belt Minder if it is currently enabled, or enable BeltMinder if it is currently disabled. 7....

AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM Your vehicle is equipped with a crash sensing and diagnostic modulewhich records information about the air bag and sensor systems. In theevent of a collision this module may save information related to thecollision including information about the air bag system ...

The air bag supplemental restraints are an intergral part of the PersonalSafety System. They are designed to be deployed in cases where thePersonal Safety System has determined the occupant conditions andcrash severity are appropriate to activate these devices. Refer to the Personal Safety System se...

• Recline the seat slightly (one or two degrees) from the uprightposition. Do not put anything on or over the air bag module. Placingobjects on or over the air bag inflation area may cause those objects to be propelled by the air bag into your face and torso causingserious injury. Do not attempt to ...

Determining if the system is operational The supplemental restraint system uses a warning indicator in theinstrument cluster or a back-up tone to indicate the condition of thesystem. Refer to the Restraints Warning Indicator section in the Instrumentation chapter. Routine maintenance of the air bag ...

facial and eye injuries or internal injuries, particularly to occupants whoare not properly restrained or are otherwise out of position at the timeof air bag deployment. Thus, it is extremely important that occupants beproperly restrained as far away from the air bag module as possible whilemaintain...

How does the side air bag system work? The side air bag system consists ofthe following: • An inflatable nylon bag (air bag)with a gas generator concealedbehind the outboard bolster ofthe driver and front passengerseatbacks. • A special seat cover designed toallow airbag deployment. • The same warni...

Several air bag systemcomponents get hot after inflation. Do not touch them afterinflation. If the side air bag hasdeployed, the air bag will not function again. The sideair bag system (including theseat) must be inspected andserviced by a qualifiedtechnician in accordance withthe vehicle service ma...

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant orchild restraint you might use. When possible, always place children under age 12...

SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all of the manufacturer’s instructions with thesafety seat you put in your vehicle. If you do not install and use thesafety seat properly, the ...

of providing a tether anchorage. For more information on top tetherstraps, refer to Attaching safety seats with tether straps. Carefully follow all of the manufacturer’s instructions includedwith the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the chi...

Installing child safety seats in the lap belt seating positions 1. Lengthen the lap belt. To lengthen the belt, hold the tongue so that itsbottom is perpendicular to the direction of webbing while sliding thetongue up the webbing. 2. Place the child safety seat in the center seating position. 3. Rou...

PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. Thissystem meets all Canadian Interference-Causing Equipment standardrequirements regulating the impulse electrical field strength of radionoise. When starting a fuel-injected engine, avoid pressing the a...

Make sure the corresponding lights illuminate briefly. If a light fails toilluminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate. STARTING THE ENGINE 1. Turn the key to 5 (START) withoutpressing the accelerator pedal andrelease as soon as the e...

High-quality blends of winter grade (E d 85) ethanol will produce satisfactory cold weather starting and driving results. However, fuelcomposition varies, and sub-optimal winter grade blends could produceincreased cranking times, rough idle or hesitation at temperatures below–18 degrees C (0 degrees...

To prevent electrical shock, do not use your heater withungrounded electrical systems or two-pronged (cheater) adapters. Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaustfumes. Take precautions to avoid its dangerous effects. If you ever smell exha...

BRAKES Your service brakes are self-adjusting. Refer to the scheduledmaintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate aperformance concern with the vehicle’s brake system. In normaloperation, automotive brake systems may emit occasional or int...

ABS warning lamp ABS The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does notilluminate momentarily at start up, remains on or continues to flash, theABS needs to be serviced. With the ABS light on, the anti-lockbrak...

Parking brake Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops. The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released....

Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy. TRACTION CONTROL Y (IF EQUIPPED) Your vehicle may be equipped with the optional Traction Control y system. This system helps you maintain the stability and st...

the engine compartment and the engine will not “rev-up” when you pushfurther on the accelerator. This is normal system behavior. The Traction Control y on/off switch, located on the right side of the instrument cluster, illuminates OFF when the system is turned OFF. TheTraction Control y system will...

AUTOMATIC TRANSAXLE OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that preventsthe gearshift lever from being moved from P (Park) when the ignition isin the ON position unless brake pedal is depressed. If you cannot move the gearshift lever out of P (P...

If the parking brake is fully released, but the brake warning lampremains illuminated, the brakes may not be working properly. See your dealer or a qualified service technician. Driving with an automatic overdrive transaxle Your automatic transaxle electronically controls the shift feel by using ana...

Understanding gearshift positions P (Park) Always come to a complete stopbefore shifting into P (Park). Makesure the gearshift lever is securelylatched in P (Park). This locks thetransaxle and prevent the frontwheels from rotating. Always set the parkingbrake fully and make sure the gearshift is lat...

• Maximum Trailer Weight: Maximum weight of a trailer the loaded vehicle (including passengers and cargo) is permitted to tow. It isdetermined by subtracting the weight of the loaded trailer towingvehicle from the GCWR for the towing vehicle. • Trailer Weight Range: Specified weight range that the t...

If driving through deep or standing water is unavoidable, proceed veryslowly. Never drive through water that is higher than the bottom of thehubs (for trucks) or the bottom of the wheel rims (for cars). Once through the water, always try the brakes. Wet brakes do not stop thevehicle as effectively a...

3.0L 4-Valve Duratec Engine Model Passenger Load -#/kg (lbs.) Luggage Load -kg (lbs.) Max TrailerWt.- kg (lbs.) Sedan 5/340 (750) 0 590 (1 300) 2/135 (300) 70 (150) 725 (1 600) 2/135 (300) 0 795 (1 750) Wagon 5/340 (750) 70 (150) 455 (1 000) 2/135 (300) 70 (150) 660 (1 450) 2/135 (300) 0 725 (1 600)...

Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes aresafe if installed properly and adjusted to the manufacturer’sspecifications. The trailer brakes must meet local and Federalregulations. Do not connect a trailer’s hydraulic brake system directly to yourvehicle’s bra...

• Allow more distance for stopping with a trailer attached. • The trailer tongue weight should be 10% of the loaded trailer weight. • After you have traveled 80 km (50 miles), thoroughly check yourhitch, electrical connections and trailer wheel lug nuts. • When stopped in traffic for long periods of...

LUGGAGE RACK (IF EQUIPPED) The rear crossbar can be adjusted to fit the item being carried. The frontcrossbar does not move. Do not load more than 44 kg (100 lbs.) on theluggage rack. To adjust cross-bar position: 1. Loosen the thumbwheel at bothends of the cross-bar. 2. Slide the cross-bar to the d...

GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford offers acomplimentary roadside assistance program. This program is separatefrom the New Vehicle Limited Warranty. The service is available: • 24–hours, seven days a week • for the Basic warranty period (Canada) o...

FUSES AND RELAYS Fuses If electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check the appropriatefuses before replacing any electricalcomponents. Always replace a fuse with one that has the specified amperagerating. ...

Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel bythe brake pedal. Remove the panel cover to access the fuses. To remove a fuse use the fuse puller tool provided on the fuse panelcover. The fuses are coded as follows. Fuse/Relay Location Fuse Am...

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 37 15A Transmission Position Switch 38 5A GEM Park Neutral Switch 39 — Not Used 40 — Not Used 41 — Not Used 42 — Not Used Power distribution box The power distribution box islocated in the engine compartment.The power d...

When driving with the temporary spare tire do not: • exceed 80 km/h (50 mph) under any circumstances • load the vehicle beyond maximum vehicle load rating listed on theSafety Compliance Label • tow a trailer • use tire chains • drive through an automatic car wash, because of the vehicle’s reducedgro...

5. Loosen each wheel lug nutone-half turn counterclockwise butdo not remove them until the wheelis raised off the ground. 6. Put the jack in the jack notchnext to the door of the tire you arechanging. Turn the jack handleclockwise until the wheel iscompletely off the ground. 7. Remove the lug nuts w...

11. Return the flat tire, jack and lugwrench to their proper storagelocations. Make sure the jack isfastened so it does not rattle whenyou drive. 12. Unblock the wheels. JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion c...

4. Check all battery terminals and remove any excessive corrosion beforeyou attach the battery cables. Ensure that vent caps are tight and level. 5. Turn the heater fan on in both vehicles to protect any electricalsurges. Turn all other accessories off. Connecting the jumper cables 1. Connect the po...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable. Make theconnection to an exposed metal part of the stalled vehicle’s engine, awayfrom the battery and the carburetor/fuel injection system. Do not use fuel ...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for anadditional three minutes before disconnecting the jumper cables. Removing the j...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingbelt. Ford Motor Company has notapproved a ...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a Scheduled Maintenance Guide which makes trackingroutine service easy. If your vehicle requires professional service, your dealership can providenec...

Do not start your engine with the air cleaner removed and donot remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel. 2. Go to the front of the vehicle andrelease the auxiliary latch located inthe c...

3.0L DOHC V6 Duratec engine 1. Automatic transmission fluid dipstick 2. Brake fluid reservoir 3. Air filter assembly 4. Battery 5. Engine oil filler cap 6. Engine oil dipstick 7. Engine coolant reservoir 8. Windshield washer fluid reservoir 9. Power steering fluid reservoir 7 6 5 4 8 9 1 2 3 Mainten...

ENGINE OIL Checking the engine oil Refer to the Scheduled Maintenance Guide for the appropriate intervalsfor checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into theoil pan. 3. Set the parking brake and ensure t...

• If the oil level is below the add1QT or MIN mark, add enough oilto raise the level within the1QT-FULL or the MIN-MAX range(depending on application). • Oil levels above the F in FULL or above the MAX mark, may causeengine damage. Some oil must be removed from the engine by aservice technician. 7. ...

Engine oil and filter recommendations Look for this certificationtrademark. Use SAE 5W-30 motor oil certified for gasoline engines by the AmericanPetroleum Institute (API). Motor oil displaying the API certification trademark will meet allrequirements for your vehicle’s engine. Ford oil specificatio...

BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked andrefilled as needed. Refer to theScheduled Maintenance Guide forthe service interval schedules. 1. Clean the reservoir cap beforeremoval to prevent dirt or waterfrom entering the reservoir. 2. Visually inspect the fluid leve...

WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid wheneveryou stop for fuel. The reservoir ishighlighted with a symbol. If the level is low, add enough fluidto fill the reservoir. In very coldweather, do not fill the reservoir allthe way. Only use a washer fluid that me...

Checking and adding washer fluid for the liftgate (if equipped) The opening for the reservoir islocated on the passenger side underthe tail lamp. Refill this reservoirwith the same fluid you use for yourwindshield. ENGINE COOLANT Checking engine coolant Your engine’s cooling system has been factory-...

Adding engine coolant Use only Ford Premium Engine Coolant E2FZ-19549-AA (inCanada, Motorcraft CXC-8-B) or a premium engine coolant thatmeets Ford specification ESE-M97B44-A. • DO NOT USE Ford Extended Life Engine CoolantF6AZ-19544-AA (orange in color). • DO NOT USE a DEX-COOL t engine coolant or an...

• Engine coolant concentrations above 60% or below 40% willdecrease the freeze protection characteristics of the enginecoolant and may cause engine damage. Plain water may be added in an emergency, but you must replace it with a 50/50 mixture of engine coolant and distilled water as soon as possible...

Always dispose of used automotive fluids in a responsible manner. Follow your community’s regulations and standards for recycling anddisposing of automotive fluids. Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Refill capacities in the Capacities ...

Vehicles driven year-round in non-extreme climates should use a 50/50mixture of engine coolant and distilled water for optimum cooling systemand engine protection. CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid.Refer to the Scheduled MaintenanceGuide for the service interval...

Automatic transmission fluid expands when warmed. To obtain anaccurate fluid check, drive the vehicle until it is warmed up(approximately 30 km [20 miles]). If your vehicle has beenoperated for an extended period at high speeds, in city trafficduring hot weather or pulling a trailer, the vehicle sho...

High fluid level Fluid levels above the safe rangemay result in transaxle failure. Anoverfill condition of transmissionfluid may cause shift and/orengagement concerns and/or possible damage. High fluid levels can be caused by an overheating condition. Adjusting automatic transmission fluid levels Be...

1. Release and open the hood. 2. Remove the four clips located on the cowl vent screen. Maintenance and care 167

3. Remove the cowl vent screen. 4. Remove the two screws retaining the cowl top inner panel shield. 5. Remove the inner panel shield. Maintenance and care 168

6. Remove the filter from the cabin air filter housing. 7. Install the new cabin air filter into the cabin air filter housing. Maintenance and care 169

8. Replace the inner panel shield. 9. Replace the two screws retaining the cowl top inner panel shield. 10. Replace the cowl vent screen. Maintenance and care 170

11. Replace the four clips located on the cowl vent screen. BATTERY Your vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice. However, for severe usage or in high temperature climates, check thebattery electrolyte lev...

If your battery has a cover/shield, make sure it is reinstalledafter the battery has been cleaned or replaced. For longer, trouble-free operation, keep the top of the battery clean anddry. Also, make certain the battery cables are always tightly fastened tothe battery terminals. If you see any corro...

2. Put the gearshift in P (Park), turn off all accessories and start theengine. 3. Run the engine until it reaches normal operating temperature. 4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine to idle for at least one minute. 6. With your foot on the brak...

Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from thewindshield and lock into the serviceposition. 2. Turn the blade at an angle fromthe wiper arm. Push the lock pinmanually to release the blade andpull the wiper blade down towardthe windshield to remove it from ...

The temperature grade for this tire is established for a tire thatis properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or incombination, can cause heat buildup and possible tire failure. SERVICING YOUR TIRES Checking the tire pressure • Us...

Replacing the tires Replace the tires when the wearband is visible through the tiretreads. When replacing full size tires, never mix radial bias-belted, orbias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires are the same size, speedrating, and...

recommended that steel wheels are used of the same size andspecifications as those originally installed. Follow these guidelines when using snow tires and chains: • Use only cable type chains offered by Ford as an accessory orequivalent. SAE class “S” or other conventional link type chains maycause ...

Automotive fuels can cause serious injury or death if misused ormishandled. Fuel ethanol and gasoline may contain benzene, which is acancer-causing agent. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materialsand any open flames beforefueling your vehicle....

The flow of fuel through a fuel pump nozzle can produce staticelectricity, which can cause a fire if fuel is pumped into an ungrounded fuel container. Use the following guidelines to avoid static build-up when filling anungrounded fuel container: • Place approved fuel container on the ground. • DO N...

Motor Company. Fuel stations may apply to be certified as meeting thesestandards. However, not all stations meet these standards at this time. Toensure proper operation of your FFV on fuel ethanol, refuel at certifiedstations. If you are experiencing a rough or rolling idle after start-up with theou...

NOT accurate as a measure of fuel economy. We do not recommendtaking fuel economy measurements during the first 1 600 km (1 000miles) of driving (engine break-in period). You will get a more accuratemeasurement after 3 000 km–5 000 km (2 000 miles-3 000 miles). Filling the tank The advertised fuel c...

4. Subtract your initial odometer reading from the current odometerreading. 5. Follow one of the simple calculations in order to determine fueleconomy: Multiply liters used by 100, then divide by total kilometerstraveled. Divide total miles traveled by total gallons used. Keep a record for at least ...

• Resting your foot on the brake pedal while driving may reduce fueleconomy. • Combine errands and minimize stop-and-go driving. Maintenance • Keep tires properly inflated and use only recommended size. • Operating a vehicle with the wheels out of alignment will reduce fueleconomy. • Use recommended...

expected on the vehicle under optimum conditions. Your fuel economymay vary depending upon the method of operation and conditions. EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to comply withapplicabl...

permitted to intentionally remove an emission control device or preventit from working. Information about your vehicle’s emission system is onthe Vehicle Emission Control Information Decal located on or near theengine. This decal identifies engine displacement and gives some tune upspecifications. P...

• License plate lamp Do not remove lamp bulbs unless they will be replaced immediately. If abulb is removed for an extended period of time, contaminants may enterthe lamp housings and affect performance. Replacing headlamp bulbs To remove the headlamp bulb: 1. Make sure headlamp switch is inOFF posi...

5. Disconnect the electricalconnector from the bulb by pullingrearward. 6. Remove the bulb retaining ring byrotating it counterclockwise. 7. Remove the old bulb from thelamp assembly by pulling it straightout of the lamp assembly. To install the new bulb: Handle a halogen headlamp bulb carefully and...

2. Install the bulb retaining ring over the plastic base and lock the ringby rotating clockwise until it snaps into place. 3. Connect the electrical connector to the bulb. 4. Install the protective dust shield and lock the shield by rotating itclockwise until it locks into position. 5. Carefully pos...

4. Remove the bulb socket byrotating it counterclockwise, thenpulling it out of the lamp assembly. 5. Pull the bulb from the socket andpush in the new bulb. 6. Install the bulb socket into thelamp assembly by rotating itclockwise. 7. Install the lamp assembly on thevehicle with three nut and washera...

3. On the wall or screen you willobserve an area of high intensitylight. The top of the high intensityarea should touch the horizontalreference line, if not, the beam willneed to be adjusted. To see a clearer light pattern foradjusting, you may want to blockthe light from one headlamp whileadjusting...

Washing your vehicle Wash your vehicle regularly withcold or lukewarm water. Never usestrong detergents or soap. If yourvehicle is particularly dirty, use aquality car wash detergent. Alwaysuse a clean sponge, washing gloveor similar device and plenty of waterfor best results. To avoid spots,avoid w...

To avoid scratching the lamps, do not use a dry paper towel, chemicalsolvents or abrasive cleaners. Cleaning the wiper blades, windshield and rear window If the wiper blades do not wipe properly, clean the wiper blade rubberelement with undiluted windshield washer solution or a mild detergent.To avo...

Cleaning the instrument panel Clean with a damp cloth, then dry with a dry cloth. Avoid cleaner or polish that increases the gloss of the upper portion ofthe instrument panel. The dull finish in this area helps protect the driverfrom undesirable windshield reflection. Do not use chemical solvents or...

refer to the Safety belt maintenance section in the Seating and safety restraints chapter. Cleaning leather seats (if equipped) To clean, simply use a soft cloth dampened with water and a mild soap.Wipe the leather again with a damp cloth to remove soap residue. Drywith a soft cloth. For tougher soi...

MOTORCRAFT PART NUMBERS Component 3.0L V6 Vulcanengine 3.0L FFV V6engine 3.0L DOHC V6Duratec engine Air filterelement 1 FA-1683 FA-1683 FA-1683 Fuel filter FG-1006 FG-1006 FG-1006 Battery(standard) BXT-58R BXT-58R BXT-36R Battery(optional) BXT-36R N/A N/A Oil filter FL-400-S FL-400-S FL-820-S PCV va...

REFILL CAPACITIES Fluid Ford Part Name Application Capacity Brake fluid High PerformanceDOT 3 MotorVehicle BrakeFluid All Fill to line onreservoir Enginecoolant 1 Premium EngineCoolant 3.0L V6 Vulcanengine 11.0L(11.6 quarts) 3.0L V6Duratec engine 10.0L(10.6 quarts) Engine oil(includes filterchange) ...

Ford Extended Service Plan You can get more protection for your new car or light truck bypurchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESPis an optional service contract which is backed by Ford Motor Companyor Ford Motor Service Company (in the U.S.) and Ford of Canada (inCanada). ...

If you have questions or concerns, or are unsatisfied with the service youare receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at yourselling/servicing dealership. 2. If your inquiry or concern remains unresolved, contact the SalesManager or Service Manager at t...

replacement or repurchase remedies provided by certain state laws. Thisdispute handling procedure is not required prior to enforcing statecreated rights or other rights which are independent of theMagnuson-Moss Warranty Act or state replacement or repurchase laws. THE DISPUTE SETTLEMENT BOARD (U.S. ...

Concerns are ineligible for review if the New Vehicle Limited Warrantyhas expired at receipt of your application and, in certain states eligibilityis dependent upon the customer’s possession of the vehicle. Eligibility may differ according to state law. For example, see the uniquebrochures for Calif...

• a brief summary of the action taken by the dealer(s) and Ford MotorCompany • the names (if known) of all the people you contacted at thedealership(s) • a description of the action you expect to resolve your concern You will receive a letter of explanation if your application does notqualify for Bo...

You may also contact the North American Customer Assistance Center at1-800-392-3673 (Ford), TDD for the hearing impaired: 1-800-232-5952 orby writing to the Center at the following address: Ford Motor CompanyCustomer Assistance Center16800 Executive Plaza DriveP.O. Box 6248Dearborn, Michigan 48121 U...

The use of leaded fuel in your vehicle without proper conversion maydamage the effectiveness of your emission control system and may causeengine knocking or serious engine damage. Ford Motor Company/Ford ofCanada is not responsible for any damage caused by use of improperfuel. In the United States, ...

ORDERING ADDITIONAL OWNER’S LITERATURE To order the publications in this portfolio: Make checks payable to: HELM, INCORPORATEDP.O. Box 07150Detroit, Michigan 48207 For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST,for credit card holders only Obt...

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle hasa defect that could cause a crash, orcould cause injury or death, youshould immediately inform theNational Highway Traffic SafetyAdministration (NHTSA) in additionto notifying Ford Motor Company. If NHTSA receives similar compl...

Accessory delay ..........................54Air bag supplementalrestraint system ................94,95,98 and child safety seats ..............96description ...........................95,98disposal ....................................100driver air bag ..................94,97,99indicator light .........

brake ..........................................12charging system ........................12check coolant ............................11cruise indicator .........................11door ajar ......................................9high beam ...................................8low coolant ................

Item Information Required fuel Refer to 9 Octane recommendations 9 in the Maintenance and care chapter. Fuel tank capacity 68.1L (18 gallons) Engine oil capacity (including filterchange)-3.0L V6 Vulcan engine 4.25L (4.5 quarts). Use MotorcraftSAE 5W-20 Super Premium MotorOil, Ford specificationWSS-M...