Ford 1999 F-150- Manuals

Service engine soon Your vehicle is equipped with acomputer that monitors the engine’semission control system. Thissystem is commonly known as theOn Board Diagnostics System (OBDII). The OBD II system protects theenvironment by ensuring that your vehicle continues to meetgovernment emission standard...

Light is blinking: Engine misfire is occurring which could damage your catalytic converter.You should drive in a moderate fashion (avoid heavy acceleration anddeceleration) and have your vehicle serviced at the first availableopportunity. Under engine misfire conditions, excessive exhaust temperatur...

Anti-lock brake system (ABS) Momentarily illuminates when theignition is turned to the ON positionand the engine is off. If the lightremains on, continues to flash orfails to illuminate, have the systemserviced immediately. With the ABS light on, the anti-lock brake systemis disabled and normal brak...

Oil pressure/Engine coolant This light will come on when thekey is in the ON position and the: • engine coolant temperature isvery high • engine oil pressure is low The light serves as a notice that a system needs your attention and tocheck the engine coolant temperature gauge and the engine oil pre...

Check air suspension (if equipped) Illuminates momentarily when theignition is turned to the ON positionand the engine is OFF. The light alsoilluminates when the air suspensionsystem requires servicing. For information, refer to Air suspension system in the Driving chapter. Door ajar Illuminates whe...

Speedometer Indicates the current vehicle speed. Engine coolant temperature gauge Indicates the temperature of theengine coolant. At normal operatingtemperature, the needle remainswithin the normal area (the areabetween the “H” and “C”). If itenters the red section, the engine isoverheating. Stop th...

Engine oil pressure gauge This shows the engine oil pressurein the system. Sufficient pressureexists as long as the needle remainsin the normal range (the areabetween the “L” and “H”). If the gauge indicates low pressure,stop the vehicle as soon as safelypossible and switch off the engineimmediately...

HEADLAMP CONTROL Rotate the headlamp control to thefirst position to turn on the parkinglamps. Rotate to the second positionto also turn on the headlamps. Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: • the engine must be running and • the headl...

PANEL DIMMER CONTROL Use to adjust the brightness of theinstrument panel during headlampand parklamp operation. • Rotate up to brighten. • Rotate down to dim. • Rotate to full down position toturn off. AUTOLAMP CONTROL (IF EQUIPPED) The autolamp system provides lightsensitive automatic on-off contro...

4WD CONTROL (IF EQUIPPED) This control operates the 4WD.Refer to the Driving chapter for more information. AUXILIARY POWER POINT The auxiliary power point is locatedon the instrument panel. Do not plug optional electricalaccessories into the cigarette lighter.Use the power point. 4H 2H 4L Controls a...

USING YOUR AUDIO SYSTEM AM/FM Stereo AM/FM Stereo Your vehicle is equipped with a delayed accessory feature. This featureenables the audio playing media to continue playing up to 10 minutesafter the ignition has been turned off, or until a door is opened. 1 2 3 4 AM/FM SEEK TONE CLK TUNE TONE VOL 12...

Volume/power control Press the control to turn the audiosystem on or off. Turn the control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition switch is turned back on. AM/FM s...

• Press to move to the next frequency up the band (whether or not a listenable station is located there). Hold for quick movement. Seek function The seek function control works in radio mode. Seek function in radio mode • Press to find the next listenable station down thefrequency band. • Press to f...

AM/FM Stereo/Cassette (CD changer compatible) Your vehicle is equipped with a delayed accessory feature. This featureenables the audio playing media to continue playing up to 10 minutesafter the ignition has been turned off, or until a door is opened. Volume/power control Press the control to turn t...

If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition switch is turned back on. AM/FM select The AM/FM select control works inradio, tape and CD changer modes(if equipped). AM/FM select in radio mode Thi...

Tune adjust for CD changer (if equipped) • Press to select the previous disc in the CD changer. (Play willbegin on the first track of thedisc unless the CD changer is inshuffle mode. Refer to Shuffle feature for more information. Hold the control to continue reversing through the disc. • Press to se...

Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stationson the frequency band. Press the SCAN control again to stop the scanmode. Scan function in CD changer mode (if equipped) Press the SCAN control to hear a brief sampling of all selections on theCD. (...

Treble adjust The treble adjust control allows youto increase or decrease the audiosystem’s treble output. Speaker balance adjust Speaker sound distribution can beadjusted between the right and leftspeakers. Speaker fade adjust Speaker sound can be adjustedbetween the front and rearspeakers. Tape se...

Automatic Music Search The Automatic Music Search featureallows you to quickly locate thebeginning of the tape selectionbeing played or to skip to the nextselection. To activate the feature, momentarilydepress the TAPE AMS button.Then, press either REW (for the beginning of the current selection) or...

Fast forward The fast forward control works in tape and CD changer modes. To fast forward in tape mode, pressthe 1–2/FF control. Tape direction will automaticallyreverse when the end of the tape isreached. Press the SIDE/REW control to stopthe fast forward of the tape. To fast forward in CD changer ...

To set the minute, press and holdthe CLK control and press: • to decrease minutes and • to increase minutes. The CLK control will allow you to switch between media display mode(radio station, stereo information, etc.) and clock display mode (time).When in clock mode, the media information will displ...

• to increase volume compensation • to decrease or shut off the volume compensation AM/FM select The AM/FM select control works inradio, tape and CD modes (ifequipped). AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press thecontrol to switch between AM, FM1 o...

Tune adjust for CD changer • Press to select the previous disc in the CD changer. (Play willbegin on the first track of thedisc unless the CD changer is inshuffle mode.) Refer to Shuffle feature for more information. Hold the control to continue reversing through the discs. • Press to select the nex...

Scan function The scan function works in radio,tape or CD mode (if equipped). Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stationson the frequency band. Press the SCAN control again to stop the scanmode. Scan function in tape mode Press the SCAN cont...

Autoset memory preset Autoset allows you to set strong radio stations without losing youroriginal manually set preset stations. This feature is helpful on tripswhen you travel between cities with different radio stations. Starting autoset memory preset 1. Select a frequency using the AM/FM select co...

• In CD mode, pressing the REW control for less than three secondsresults in slow rewind. Pressing the control for more than threeseconds results in fast rewind. Fast forward The fast forward control works intape and CD modes (if equipped). • In the tape mode, tape directionwill automatically revers...

Compression feature Compression adjust brings soft andloud CD passages together for amore consistent listening level. Press the COMP control to activateand deactivate compression adjust. The effect of the feature varies with the music content. Shuffle feature The shuffle feature operates in CDmode a...

• Use the SEL control to selectTYPE, NAME or NONE. RDS clock feature Refer to Setting the clock for information. Mute mode Press the control to mute theplaying media. Press the controlagain to return to the playing media. Setting the clock with radio data system (RDS) feature Press the RDS control u...

Premium AM/FM Stereo/Single CD Radio with Premium Sound Your audio system is equipped with selective lighting, a unique lightingstrategy. This lighting feature is operable when the headlamps areilluminated. During the operation of any selected mode, lighting for theindividual function controls will ...

Turn the control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition switch is turned back on. Speed sensitive volume (if equipped) With this feature, radio volume changes auto...

• Do not expose tapes to direct sunlight, high humidity, extreme heat orextreme cold. Allow tapes that may have been exposed to extremetemperatures to reach a moderate temperature before playing. • Tighten very loose tapes by inserting a finger or pencil into the holeand turning the hub. • Remove lo...

Audio system warranties and service Refer to the “Warranty Guide” for audio system warranty information. If service is necessary, see your dealer or a qualified technician. CLIMATE CONTROL SYSTEM Heater only system (if equipped) Fan speed control Controls the volume of air circulatedin the vehicle. ...

• FLOOR-Allows for maximum heating. Distributes outside air throughthe floor ducts. • FLOOR & DEF-Distributes outside air through the floor ducts and thewindshield defroster ducts. • DEF -Distributes outside air through the windshield defroster ducts. It can be used to clear ice or fog from the ...

Manual heating and air conditioning system (if equipped) Fan speed control Controls the volume of air circulatedin the vehicle. Temperature control knob Controls the temperature of theairflow inside the vehicle. Mode selector control Controls the direction of the airflowto the inside of the vehicle....

Operating tips • In humid weather, select DEF before driving. This will prevent your windshield from fogging. After a few minutes, select any desiredposition. • To prevent humidity buildup inside the vehicle, don’t drive with theclimate control system in the OFF position. • Don’t put objects under t...

PASSENGER AIR BAG ON/OFF SWITCH This switch must be used todeactivate the passenger air bagwhenever a child seat is used in theright front or center front passengerseat position. Refer to Passenger air bag ON/OFF switch in the Seating and safety restraints chapter. POSITIONS OF THE IGNITION 1. ACCES...

To turn speed control off • Press OFF or • Turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speedwill be erased. To set a speed • Press SET/SET ACC/SET ACCEL.For speed control to operate, thespeed control must be ON andthe vehicle speed must be greater...

To disengage speed control • Depress the brake pedal or • Depress the clutch pedal (ifequipped) Disengaging the speed control willnot erase the previouslyprogrammed set speed. Pressing OFF will erase thepreviously programmed set speed. ON OFF Controls and features 65

To return to a previously set speed • Press RES/RSM/RESUME. ForRES/RSM/RESUME to operate,the vehicle speed must be fasterthan 48 km/h (30 mph). TILT STEERING WHEEL (IF EQUIPPED) Pull the tilt steering control towardyou to move the steering wheel upor down. Hold the control whileadjusting the wheel t...

HAZARD FLASHER For information on the hazard flasher control, refer to Hazard flasher in the Roadside emergencies chapter. WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper controlto the desired interval, low or highspeed position. The bars of varying length are forintermittent wipers. Wh...

HIGH BEAMS Push forward to activate. FLASH TO PASS Pull toward you to activate andrelease to deactivate. OVERDRIVE CONTROL Activating overdrive (Overdrive) is the normal drive position for the best fuel economy. The overdrive function allows automatic upshifts to second, third andfourth gear. Deacti...

The transmission will operate ingears one through three. To returnto normal overdrive mode, press theTransmission Control Switch again.The TCIL (the word OFF) will nolonger be illuminated. When you shut off and re-start your vehicle, the transmission willautomatically return to normal (Overdrive) mo...

• Press the bottom portion of therocker switch to open. One touch down • Press AUTO completely down andrelease quickly. The driver’swindow will open fully. Depressagain to stop window operation. Accessory delay (if equipped) With accessory delay, the window switches may be used for up to tenminutes ...

POWER SIDE VIEW MIRRORS (IF EQUIPPED) The ignition must be in ACC or ON position to adjust the power sideview mirrors. To adjust your mirrors: 1. Select L to adjust the left mirroror R to adjust the right mirror. 2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the cente...

TAILGATE REMOVAL Your tailgate is removable to allowmore room for loading. 1. Lower the tailgate. 2. Use a screwdriver to pry thespring clip (on each connector) pastthe head of the support screw.Disconnect cable. 3. Disconnect the other cable. 4. Lift tailgate to a 45 degree angle. 5. Lift right sid...

3. Pull one side of the cover outward and upward away from the side railworking from the rear to the front. 4. Starting from the opposite side of the vehicle, pull cover away fromthe side rail and roll the cover from rear to front. 5. Secure the cover behind the cab with two straps. The cover may be...

Styleside only: • Remove three cross bars from pickup box by pushing towards eitherside to release tension. Stow the cross bars in the notches behind therolled cover in the pickup box. • Lower tailgate, depress the levers on each side of the rear rail andpush rear rail towards the front of the picku...

your vehicle. Each time you start your vehicle, the SecuriLock y key is read by the SecuriLock y passive anti-theft system. If the SecuriLock y key identification code matches the code stored in the SecuriLock y passive anti-theft system, the vehicle’s engine is allowed to start. If theSecuriLock y ...

If the programming procedure was not successful, the new SecuriLock y key(s) will not operate the vehicle’s engine. The theft indicator will flashon and off. Wait at least one minute and then repeat the procedure fromstep 1. If failure repeats, bring your vehicle to your dealership to havethe spare ...

This process will also arm your anti-theft system (if equipped). For moreinformation on arming the anti-theft system, refer to Anti-theft system in this chapter. Sounding a panic alarm Press this control to activate thealarm. To deactivate the alarm, press thecontrol again or turn the ignition toACC...

Deactivating/activating the autolock feature Before following the procedure, make sure that the ignition is OFF andall vehicle doors and the liftgate window are closed. You must complete steps 1-7 within 30 seconds or the procedure willhave to be repeated. If the procedure needs to be repeated, you ...

Illuminated entry The illuminated entry system will turn on the interior lights when theremote transmitter unlock control is pressed. The illuminated entry system will turn off the interior lights if theignition switch is turned to the RUN position, or if the remotetransmitter lock control is presse...

SEATING Adjusting the front manual seat Never adjust the driver’s seat or seatback when the vehicle ismoving. Do not pile cargo higher than the seatbacks to avoid injuringpeople in a collision or sudden stop. Always drive and ride with your seatback upright and the lapbelt snug and low across the hi...

Captain’s chair (if equipped) • Lift the release bar to move theseat forward or rearward. Makesure that the seat is relatchedinto place. • Pull the seatback handle up torecline the seat. • Push the release lever down toquickly fold the seatback forward. Adjusting the front power seat (if equipped) N...

Press to raise or lower the rearportion of the seat cushion. Press the control to move the seatforward, backward, up or down. Using the manual lumbar support Turn the lumbar support controltoward the front of vehicle toincrease firmness. Turn the lumbar support controltoward the rear of vehicle toin...

60/40 Split Rear Seat (if equipped) When folded down, the rear seatsprovide a “load floor” for additionalstorage space. To fold down the rearseats: • Pull the straps to lower the seatcushions. • Store the center safety belt in theopening on the seat back. When returning the seats to theirnormal posi...

SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lapbelt snug and low across the hips. To prevent the risk of injury, make sure children sit where theycan be properly restrained. Never let a passenger hold a child on his or her lap while theveh...

Automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt willstill retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. When to use the automatic locking mode • When a tight lap/shoulder fit is de...

• Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automatic lockingmode. How to disengage the automatic locking mode Disconnect the combination lap/shoulder belt and allow it to retractcompletely to disengage the automatic ...

Conditions of operation If... Then... The driver’s safety belt is notbuckled before the ignition switchis turned to the ON position... The safety belt warning lightilluminates for one to two minutesand the warning chime sounds forfour to eight seconds. The driver’s safety belt is buckledwhile the in...

The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt propellant. This mayconsist of cornstarch, talcumpowder (to lubricate the bag) orsodium compounds (e.g., bakingsoda) that result from thecombustion ...

• and the electrical wiring which connects the components. The RCM (restraints control module) monitors its own internal circuitsand the supplemental air bag electrical system warning (including thepassenger air bag deactivation switch, the impact sensors, the systemwiring, the air bag system readin...

Passenger air bag ON/OFF switch An air bag ON/OFF switchhas been installed in this vehicle. Before driving, always look at the face of the switch tobe sure the switch is in the properposition in accordance with theseinstructions and warnings. Failureto put the switch in a properposition can increase...

In order to avoid inadvertent deployment of the passenger airbag, always remove the ignition key from the passenger air bag ON/OFF switch. Turning the passenger air bag back on The passenger air bag remains OFF until you turn it back ON. 1. Insert the ignition key and turnthe switch to ON. 2. The OF...

The safety belts for the driver and right front passenger seatingpositions have been specifically designed to function together with the air bags in certain types of crashes. When you turn OFF your air bag,you not only lose the protection of the air bag, you also may reduce theeffectiveness of your ...

• the infant has a medical condition which, according to the infant’sphysician, makes it necessary for the infant to ride in the front so thatthe driver can constantly monitor the child’s condition. 2. Child age 1 to 12. A child age 1 to 12 must ride in the front seat because: • the vehicle has no r...

• the child has a medical condition that, according to the child’sphysician, makes it necessary for the child to ride in the front seat sothat the driver can monitor the child’s condition. 3. Medical condition: A passenger has a medical condition that, according to his or her physician: • poses a sp...

7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with your knee on thechild seat. 8. Allow the safety belt to retract toremove any slack in the belt. 9. Before placing the child in theseat, forcibly tilt the seat forwardand back to...

5. Push down on the child seat while pulling on the loose end of the lapbelt webbing to tighten the belt. 6. Before placing the child into the child seat, forcibly tilt the child seatfrom side to side and in forward direction to make sure that the seat isheld securely in place. If the child seat mov...

PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meetsall Canadian Interference-Causing Equipment standard requirementsregulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerato...

3. Turn the key to 4 (ON) withoutturning the key to 5 (START). Make sure the corresponding lights illuminate briefly. If a light fails toilluminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate. STARTING THE ENGINE 1. Turn the key to 5 (START)wit...

3. If the temperature is below -12°C (10°F) and the engine does notstart in fifteen seconds on the first try, turn the key OFF and wait tenseconds and try again. If the engine does not start in two attempts,depress the accelerator and start the engine while holding theaccelerator down to the floor. ...

Engine exhaust, some of its constituents, and certain vehiclecomponents contain or emit chemicals known to the State of California to cause cancer, and birth defects or other reproductiveharm. Important ventilating information If the engine is idling while the vehicle is stopped in an open area forl...

BRAKES Your service brakes are self-adjusting. Refer to the scheduledmaintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate aperformance concern with the vehicle’s brake system. In normaloperation, automotive brake systems may emit occasional or int...

ABS warning lamp The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned on and the engine is off. If the light does notilluminate momentarily at start up, remains on or continues to flash, theABS needs to be serviced. With the ABS light on, the anti-lockbr...

Parking brake Apply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops. The BRAKE warning lamp in theinstrument cluster illuminates andremains illuminated (when theignition is turned ON) until theparking brake is released....

Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy. TRACTION-LOK AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly whenone wheel is on a poor traction surface. Under normal...

If the steering wanders or pulls, the condition could be caused by any ofthe following: • underinflated tire(s) on any wheel(s) • high crown in center of road • high crosswinds • wheels out of alignment • loose or worn components in steering linkage AIR SUSPENSION SYSTEM (IF EQUIPPED) The air suspen...

again. If the warning light reappears, turn the air suspension switch offand have the vehicle serviced by a dealer or qualified service technician. If the vehicle is loaded beyond the recommended maximum payload, theCK SUSP light may illuminate. To correct this condition, remove orredistribute the p...

If the parking brake is fully released, but the brake warning lampremains illuminated, the brakes may not be working properly. See your dealer or a qualified service technician. Driving with a 4–speed automatic transmission Understanding gearshift positions Pull the gearshift lever towards you and d...

N (Neutral) With the gearshift in N (Neutral),the vehicle can be started and isfree to roll. Hold the brake pedaldown while in this gear. (Overdrive) The normal driving position for thebest fuel economy. Transmissionoperates in gears one through four. (Overdrive) can be deactivated by pressing the T...

2 (Second) Use 2 (Second) to start-up onslippery roads or to provideadditional engine braking ondowngrades. 1 (First) Use 1 (Low) to provide maximumengine braking on steepdowngrades. Upshifts can be madeby shifting to 2 (Second) or to (Overdrive). Selecting 1 (Low) at higher speeds causes the transm...

Recommended shift speeds Upshift and downshift according to the following charts for your specificengine/drivetrain combination: Upshifts when accelerating (recommended for best fuel economy) Shift from: Transfer case position 1 (if equipped) 2H or 4H 4L 1 - 2 14 km/h (9 mph) 5 km/h (3 mph) 2 - 3 32...

Parking your vehicle 1. Disengage the clutch, apply brakeand shift into N (Neutral). 2. Set parking brake. 3. Shift into 1 (First). 4. Turn the ignition key to position3 (OFF). 1 2 4 R 3 D 3 2 1 5 4 Driving 126

Do not park your vehicle in Neutral, it may move unexpectedlyand injure someone. Use 1 (First) gear and set the parking brake fully. Reverse Make sure that your vehicle is at a complete stop before you shift intoR (Reverse). Failure to do so may damage the transmission. Put the gearshift in N (Neutr...

Using the N (Neutral) position The transfer case neutral position overrides the transmission andputs the vehicle in neutral regardless of transmission gearshiftlever position. The vehicle can move forward or backwards. This position should only be usedwhen towing the vehicle. Refer to Wrecker towing...

Shifting from 4H (4WD high) to 2H (2WD high) Move the 4WD control to 2H at anyforward speed. Shifting between 4H (4WD high) and 4L (4WD low) 1. Bring the vehicle to a stop. 2. Depress the brake. 3. Place the gearshift in N (Neutral) (automatic transmission) or depressthe clutch (manual transmission)...

Do not exceed the GVWR or the GAWR specified on the SafetyCompliance Certification Label. Do not use replacement tires with lower load carrying capacities than theoriginals because they may lower the vehicle’s GVWR and GAWRlimitations. Replacement tires with a higher limit than the originals donot i...

Do not exceed the GVWR or the GAWR specified on the SafetyCompliance Certification Label. Towing trailers beyond the maximum recommended gross trailerweight could result in engine damage, transmission/axle damage, structural damage, loss of control, and personal injury. Trailer towing tables F-150 4...

Trailer frontal area considerations: • Not to exceed towing vehicle front area without Class III trailer towingpackage • Not to exceed 5.52 square meters (60 square feet) with Class IIItrailer towing package Preparing to tow Use the proper equipment for towing a trailer, and make sure it isproperly ...

Safety chains Always connect the trailer’s safety chains to the vehicle. To connect thetrailer’s safety chains, cross the chains under the trailer tongue and allowslack for turning corners. If you use a rental trailer, follow the instructions that the rental agencygives to you. Do not attach safety ...

When towing a trailer: • Use a lower gear when towing up or down steep hills. This willeliminate excessive downshifting and upshifting for optimum fueleconomy and transmission cooling. • Anticipate stops and brake gradually. Exceeding the GCWR rating may cause internal transmissiondamage and void yo...

Exceeding these limits may allow water to enter critical vehiclecomponents, adversely affecting driveability, emissions, reliability andcausing internal transmission damage. Replace the rear axle lubricant anytime the axle has been submerged inwater. Rear axle lubricant quantities are not to be chec...

4WD – Electronic shift transfer case 1. Place transmission in N (Neutral). 2. Shift the transfer case to 2H (2WD high). 3. Lockout the center disconnect by capping off one of the front axlevacuum motor lines. See your dealer for assistance. 4. Maximum speed is 56 km/h (35 mph). 5. Maximum distance i...

• The Front Axle Accessory Reserve Capacity and the Total AccessoryReserve Capacity listed on the bottom right of the Safety ComplianceCertification Label will determine whether or not the addition of asnowplow will overload your vehicle. • The weight of the snowplow and supporting components distri...

Snowplowing with your air bag equipped vehicle Your vehicle is equipped with driverand passenger air bags. The air bagsare designed to deploy in a collisionwith a solid barrier at a range of13 to 23 km/h (8 to 14 mph) or aparked car at a range of 25 to45 km/h (16 to 28 mph). Careless or high speed d...

If you are driving more than 24 km (15 miles) at temperatures abovefreezing, angle the plow blade either full left or full right to providemaximum airflow to the radiator. If you are driving less than 24 km (15 miles) at speeds up to 64 km/h(40 mph) in cold weather, you will not need to worry about ...

HAZARD FLASHER Use only in an emergency to warn traffic of vehicle breakdown,approaching danger, etc. The hazard flashers can be operated when theignition is off. • The hazard lights control islocated on top of the steeringcolumn. • Depress hazard lights control toactivate all hazard flasherssimulta...

The fuel pump shut-off switch islocated in the passenger’s foot well,behind the kick panel. FUSES AND RELAYS Fuses If electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check the appropriatefuses before replacing any ...

Standard fuse amperage rating and color COLOR Fuse Rating Mini Fuses Standard Fuses Maxi Fuses Cartridge Maxi Fuses Fuse Link Cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Description 1 15A Audio 2 5A Powertrain Control Module (PCM), Cluster 3 20A Cigar Lighter, OBD-II Scan Tool Connector 4 15A Autolamp Module, Remote Entry Module,Mirrors 5 15A AC Clutch Relay, Speed Control Module,Reverse Lamp, Clima...

Fuse/Relay Location Fuse Amp Rating Description 401 — Not Used 501 — Powertrain Control Module Diode 502 — A/C Clutch Diode 503 — Not Used 601 — Not Used 602 — Not Used *Mini fuses **Maxi fuses CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily.Instead, gradually...

Removing the spare tire 1. Insert the jack handle into therear bumper opening. The handle will stop moving andforward resistance to turning will befelt when properly engaged. 2. Turn the handle counterclockwiseuntil tire is lowered to the ground,the tire can be slid rearward and thecable is slightly...

12. Remove the jack and fullytighten the lug nuts in the ordershown. 13. Stow the flat tire. Refer to Stowing the spare . 14. Stow the jack and lug wrench.Make sure the jack is fastened so itdoes not rattle when you drive. 15. Unblock the wheels. 16. Turn on the air suspension switch (if equipped). ...

5. Turn the heater fan on in both vehicles to protect any electricalsurges. Turn all other accessories off. Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate ...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor. The preferred locations of an exposed metal part (to ground...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for afurther three minutes before disconnecting the jumper cables. Removing the jumpe...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. Do not tow with a slingbelt. Ford Motor Company has notapproved a ...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a Scheduled Maintenance Guide which makes trackingroutine service easy. If your vehicle requires professional service, your dealership can providenec...

3. Turn off the engine and remove the key. 4. Block the wheels to prevent the vehicle from moving unexpectedly. Working with the engine on • Automatic transmission: 1. Set the parking brake and ensure the gearshift is securely latched in P(Park). 2. Block the wheels to prevent the vehicle from movin...

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.2L V6 engine 1. Battery 2. Engine oil filler cap 3. Engine oil dipstick 4. Clutch fluid reservoir (manual transmission) 5. Brake fluid reservoir 6. Engine coolant reservoir 7. Air filter assembly 8. Power steering fluid reservoir 9. Transmission flu...

ENGINE OIL Checking the engine oil Refer to the Scheduled Maintenance Guide for the appropriate intervalsfor checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into theoil pan. 3. Set the parking brake and ensure t...

• If the oil level is below the MINmark, add enough oil to raise thelevel within the MIN-MAX range. • Oil levels above the MAX mark may cause engine damage. Some oilmust be removed from the engine by a service technician. 7. Put the indicator back in and ensure it is fully seated. Adding engine oil ...

Engine oil and filter recommendations Look for this certification mark. Ford oil specification is WSS-M2C153-G. Use SAE 5W-30 motor oil certified for gasoline engines by the AmericanPetroleum Institute. Do not use supplemental engine oil additives, oil treatments or enginetreatments. They are unnece...

ENGINE COOLANT Check the level of the enginecoolant in the reservoir. Refer to theScheduled Maintenance Guide forservice interval schedules. Be sureto read and understand Precautions when servicing your vehicle in this chapter. If the engine coolant has not been checked at the recommended interval,t...

emergency, but you should replace it with a 50/50 mixture of coolant anddistilled water as soon as possible. Check the coolant level in the coolant reservoir the next few times youdrive the vehicle. If necessary, add enough of a 50/50 mixture of coolantand water to bring the liquid level into the co...

Not all coolant recycling processes produce coolant which meets Fordspecification ESE-M97B44–A, and use of such coolant may harm engineand cooling system components. Always dispose of used automotive fluids in a responsible manner. Follow your community’s regulations and standards for recycling andd...

If the engine reaches a preset over-temperature condition, the enginewill automatically switch to alternating cylinder operation. Each disabledcylinder acts as an air pump and cools the engine. When this occurs the vehicle will still operate, however: • the engine power will be limited. • the air co...

CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid.Refer to the Scheduled MaintenanceGuide for the service intervalschedules. If adding fluid isnecessary, use only MERCON t ATF. 1. Start the engine and let it run until it reaches normal operatingtemperature (the engine coolant t...

TRANSMISSION FLUID Checking automatic transmission fluid Refer to your Scheduled Maintenance Guide for scheduled intervals forfluid checks and changes. Your transmission does not consume fluid.However, the fluid level should be checked if the transmission is notworking properly, i.e., if the transmi...

Adjusting automatic transmission fluid levels Before adding any fluid, make sure the correct type is used. The type offluid used is normally indicated on the dipstick and/or dipstick handleand also in the Lubricant specifications section in the Capacities and specifications chapter. Use of a non-app...

3. Fluid level should be at bottom ofthe opening. 4. Add enough fluid through thefiller opening so that the fluid levelis at the bottom of the opening. 5. Install and tighten the fill plugsecurely. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter. Che...

3. Add only enough fluid throughthe filler opening so that the fluidlevel is at the bottom of theopening. Use only fluid that meets Ford specifications. Refer to the Capacities and specifications chapter. DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Your vehicle may be equipped with universal joints that...

2. Put the gearshift in P (Park) (automatic transmission) or the neutralposition (manual transmission), turn off all accessories and start theengine. 3. Let the engine idle for at least one minute. 4. The relearning process will automatically complete as you drive thevehicle. • The vehicle may need ...

Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from thewindshield and lock into the serviceposition. 2. Turn the blade at an angle fromthe wiper arm. Push the lock pinmanually to release the blade andpull the wiper blade down towardthe windshield to remove it from ...

SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has beenparked for at least one hour or has been driven less than 5 km (3miles). • Adjust tire pressure to recommended specifications found on the l...

• Five tire rotation Replacing the tires Replace the tires when the wearband is visible through the tiretreads. When replacing full size tires, never mix radial, bias-belted, orbias-type tires. Use only the tire sizes that are listed on the tire pressure decal. Make sure that all tires are the same ...

Do not replace your tires with “high performance” tires or largersize tires. Failure to follow these precautions may adversely affect thehandling of the vehicle and make it easier for the driver to lose control and roll over. Tires that are larger or smaller than your vehicle’s original tires may al...

WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tankmay cause leakage and lead to fuel spray and fire. If you do not use the proper fuel cap, the pressure in the fueltank can damage the fuel system or cause it to w...

• Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes,remove contact lenses (if worn), flush with water for 15 minutes andseek medical attention. Failure to seek proper medical attention couldlead to permanent injury. • Fuels can also be harmful if absorbed through the skin. If f...

Octane recommendations Your vehicle is designed to use“Regular” unleaded gasoline with an(R+M)/2 octane rating of 87. We donot recommend the use of gasolineslabeled as “Regular” that are soldwith octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes knock...

• Your “Service Engine Soon” light may come on. For more informationon the “Service Engine Soon” light, refer to the Instrumentation chapter. Fuel Filler Cap Your fuel tank filler cap has an indexed design with a one-eighth turnon/off feature. When fueling your vehicle: 1. Turn the engine off. 2. Ca...

For fuel filter replacement, see your dealer or a qualified servicetechnician. Refer to the Scheduled Maintenance Guide for theappropriate intervals for changing the fuel filter. If you replace the fuel filter, replace it with an authorizedMotorcraft part. The customer warranty may be void for anyda...

• Use the same side of the same pump and have the vehicle facing thesame direction each time you fill up. • Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1. Fill the fuel tank completel...

• Drive at reasonable speeds (traveling at 105 km /h [65 mph] uses 15%more fuel than traveling at 88 km/h [55 mph]). • Revving the engine before turning it off may reduce fuel economy. • Use of the air conditioner or defroster may reduce fuel economy. • Use of speed control (if equipped) may improve...

• Fuel economy may decrease with lower temperatures during the first12–16 km (8–10 miles) of driving. • Flat terrain driving improves fuel economy over hilly roads. • Transmissions give their best fuel economy when operated in the topcruise gear and with steady pressure on the gas pedal. • Four-whee...

Replacing front parking lamp/turn signal bulbs 1. Remove screw from the lampassembly. 2. Disengage lamp assembly (it hasa snap fit). 3. Remove bulb socket from theparking lamp assembly by turning itcounterclockwise about 1 ⁄ 4 turn. 4. Pull bulb straight out of socketand press in the new bulb. 5. In...

Replacing tail lamp/backup lamp bulbs The tail lamp/backup lamp bulbs arelocated in the same portion of thetail lamp assembly, one just belowthe other. Follow the same steps toreplace either bulb: 1. Open the liftgate to expose thelamp assemblies. 2. Remove the two screws from thetail lamp assembly....

Replacing foglamp bulbs 1. Remove the bulb socket from thefoglamp by turningcounterclockwise. 2. Disconnect the electricalconnector from the foglamp bulb. 3. Connect the electrical connector to the new foglamp bulb. 4. Install the bulb socket in the foglamp turning clockwise. Replacing license plate...

AIMING THE HEADLAMPS The alignment of your headlamps should be checked by a qualifiedservice technician if: • Oncoming motorists frequently signal you to deactivate your highbeams, and your high beams are not activated. • The headlamps do not seem to provide enough light for clear nightvision. • The...

Waxing your vehicle Wax when water stops beading on the surface. This could be every threeor four months, depending on operating conditions. Use only carnauba or synthetic-based waxes. Use cleaning fluid oralcohol with a clean cloth to remove any bugs and tar before waxingvehicle. Use tar remover to...

Cleaning the wiper blades and windshield If the wiper blades do not wipe properly, clean the wiper blade rubberelement with undiluted windshield washer solution or a mild detergent.To avoid damaging the blades, do not use fuel, kerosene, paint thinner orother solvents. If the wiper still does not wi...

Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended forcleaning upholstery or carpets. Do not bleach or dye the belts, becausethese actions may weaken the belt webbing. Check the safety belt system periodically to make sure there are nonicks, wear o...

MOTORCRAFT PART NUMBERS Component 4.2L V6 engine 4.6L V8 engine 5.4L V8 engine Air filterelement FA-1634 FA-1634 FA-1634 Fuel filter FG-986B FG-986B FG-986B Oil filter FL-400-S FL-820-S FL-820-S PCV valve EV-152 EV-233 EV-233 Battery(standard) BXT-59 BXT-59 BXT-59 Battery(heavy duty) BXT-65-650 BXT-...

Fluid Ford PartName Application Capacity Transmissionfluid MotorcraftMERCON t ATF 5-speed manual 3 3.5L (3.75 quarts) Automatic- 4R100(4x2) 4 15.0L (15.9 quarts) 5 Automatic- 4R100(4x4) 4 15.5L (16.4 quarts) 5 MotorcraftMERCON t V ATF Automatic- 4R70W 13.1L (13.9 quarts) Front axle MotorcraftSAE 75W...

Fill to 6–14 mm (1/4–9/16 inch) below bottom of filler hole. 4 Ensure the correct automatic transmission fluid is used for a specific application. Check the container to verify the fluid is MERCON t approved. Transmission fluid requirements are indicated on the dipstickhandle. Refer to the Scheduled...

Item Ford partname orequivalent Ford partnumber Fordspecification Engine coolant Ford PremiumEngine Coolant E2FZ-19549-AA(in Oregon,F5FZ-19549-CC,in Canada,MotorcraftCXC-10) ESE-M97B44-A Engine oil Motorcraft 5W30Super PremiumMotor Oil XO-5W30-QSP WSS-M2C153-Gand APICertificationMark Hinges, latches...

Flareside Dimension Body Style Regular Cab 4x2 Regular Cab 4x4 Super Cab 4x2 Super Cab 4x4 (1) Overalllength 5 212 mm(205.2 in) 5 250 mm(206.7 in) 5 684 mm(223.8 in) 5 722 mm(225.3 in) (2) Overallwidth 2 014 mm(79.3 in) 1 2 028 mm(79.8 in) 1 1 989 mm(78.3 in) 1 2 019 mm(79.5 in) 1 (3) Overallheight ...

IDENTIFYING YOUR VEHICLE Safety compliance label The National Highway Traffic SafetyAdministration Regulations requirethat a Safety ComplianceCertification Label be affixed to avehicle and prescribe where theSafety Compliance CertificationLabel may be located. The SafetyCompliance Certification Labe...

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle hasa defect that could cause a crash, orcould cause injury or death, youshould immediately inform theNational Highway Traffic SafetyAdministration (NHTSA) in additionto notifying Ford Motor Company. If NHTSA receives similar compl...

Accessory delay ..........................70Air bag supplemental restraintsystem ..........................................95 and child safety seats ..............96description ................................95disposal ......................................98indicator light ...........................

Item Information Recommended fuel Unleaded fuel only - 87 octane Fuel tank capacity-4 x 4 Regularcab with short wheelbase 92.7L (24.5 gallons) Fuel tank capacity-4 x 2 Regularcab and all SuperCab with shortwheelbase 94.6L (25.0 gallons) Fuel tank capacity-Long wheelbase 113.6L (30.0 gallons) Engine ...

5.4L SUPERCHARGED V8 ENGINE 1. Engine oil dipstick 2. Power steering fluid reservoir 3. Brake fluid reservoir 4. Power distribution box 5. Engine coolant reservoir 6. Air filter assembly 7. Intercooler coolant reservoir 8. Windshield washer fluid reservoir 9. Battery 10. Transmission fluid dipstick ...

ENGINE Configuration Supercharged longitudinally mounted,90-degree V8, single overhead cam, cast ironcylinder block and cast aluminum cylinderheads Bore x Stroke 90.2 x 105.8 mm (3.55 x 4.17 in) Displacement 5409 cc (330.1 cid) Compression ratio 8.4:1 Horsepower(SAE net) 269 kW @ 4750 rpm (360 HP @ ...

DRIVETRAIN Rear axle 9.75 in limited-slip differential with 3.55:1 final driveratio Driveshaft Steel with hardened yoke Transmission Modified 4R100 4-speed automatic with OD lockout Gear ratios Gear Ratio 1st 2.71 2nd 1.53 3rd 1.00 4th (OD) 0.71 Reverse 2.176 Drivetrain 8

PERFORMANCE 0-100 km/h (0-60 mph) 6.2 seconds 400 meters (quarter mile) 14.63 seconds @ 156.7 km/h(97.4 mph) Top speed 225 km/h (140 mph) Braking, 100-0 km/h (60-0 mph) 41.8 meters (137 ft.) 183 meter slalom (600 ft.) 102.4 km/h (63.6 mph) 61 meter skid pad (200 ft.) 0.85 g Performance 9

OPTIONS, COLOR AND TRIM • Tonneau cover • 6–disc CD player • Trailer tow package Exterior: • Black Clearcoat • Oxford White • Bright Red Clearcoat Interior: • Medium Graphite Leather/Cloth Options, color and trim 10

MOTORCRAFT PART NUMBERS Component 5.4L Supercharged V8 engine Air filter element FA-1634 Fuel filter FG-986B Battery BXT-65-650 Oil filter FL-820S PCV valve EV-233 Spark plugs 1 AGSF-12E or AGSF-12FM1 2 1 Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information. 2 I...

OCTANE RECOMMENDATIONS Your vehicle is designed to use“Premium” unleaded gasoline withan (R+M)/2 octane rating of 91 orhigher for optimum performance.The use of gasolines with loweroctane ratings may degrade performance. We do not recommend the useof gasolines labeled as “Premium” in high altitude a...

A WORD ABOUT WARRANTY COVERAGE The F–150 Lightning carries the same warranty coverage as other FordF-150 models. This information is covered in its entirety in the FordMotor Company Warranty Guide. The F–150 Lightning or any SVT can be serviced under warranty at anyFord-Lincoln-Mercury dealer nation...