Ford 1999 E-450- Manuals

WARNING LIGHTS AND CHIMES Brake system warning Momentarily illuminates when theignition is turned to the ON positionand the engine is off. If the brakewarning lamp does not illuminate atthis time, seek service immediately.Also illuminates when the parking brake is engaged. Illumination afterreleasin...

government emission standards. The OBD II system also assists theservice technician in properly servicing your vehicle. The Service Engine Soon indicator light illuminates when the ignition is first turned to the ON position to check the bulb. If it comes on after theengine is started, one of the en...

Transmission control indicator light (TCIL) The word OFF located on the endof the gearshift lever is thetransmission control indicator light(TCIL). The TCIL may flash steadily if amalfunction is detected. If the TCIL is flashing, contact your Ford dealeras soon as possible. If this condition persist...

GAUGES Speedometer Indicates the current vehicle speed. Fuel gauge Displays approximately how muchfuel is in the fuel tank (when thekey is in the ON position). The fuelgauge may vary slightly when thevehicle is in motion. The ignitionshould be in the OFF position whilethe vehicle is being refueled. ...

Engine coolant temperature gauge Indicates the temperature of theengine coolant. At normal operatingtemperature, the needle remainswithin the normal area (the areabetween the “H” and “C”). If itenters the red section, the engine isoverheating. Stop the vehicle assoon as safely possible, switch offth...

HEADLAMP CONTROL • Pull the headlamp control towardyou to the first position to turnon the parking lamps, tail lamps,license plate lamps and markerlamps. • Pull the headlamp control towardyou to the outer position to turnon the headlamps (in addition tothe previous lamps). Daytime running lamps (DRL...

Flash to pass Pull toward you to activate andrelease to deactivate. PANEL DIMMER CONTROL To adjust the brightness of theinstrument panel: • Rotateclockwise/counterclockwise whenthe headlamp control is in theparking lamp or low-beamposition. To turn on the courtesy lamp andcargo lamps: • Rotate fully...

Fan speed control Controls the volume of air circulatedin the vehicle. Temperature control knob Controls the temperature of theairflow inside the vehicle. Onheater-only systems, the air cannotbe cooled below the outsidetemperature. Mode selector control Controls the direction of the airflowto the in...

Operating tips • In humid weather, select before driving. This will help to prevent your windshield from fogging. After a few minutes, select any desiredposition. • To prevent humidity buildup inside the vehicle, don’t drive with theclimate control system in the OFF position. • Don’t put objects und...

Under normal conditions, your vehicle’s climate control system should beleft in any position other than MAX A/C or OFF when the vehicle isparked. This allows the vehicle to “breathe” through the outside air inletduct. • MAX A/C-Uses recirculated air to cool the vehicle. MAX A/C is noisierthan NORM A...

• To prevent humidity buildup inside the vehicle, don’t drive with theclimate control system in the OFF position. • Don’t put objects under the front seat that will interfere with theairflow to the back seats. • Remove any snow, ice or leavesfrom the air intake area (at thebottom of the windshield)....

• To control the auxiliary fan withthis control, the rear fan switchon the front control unit must bein the rear control position. • The auxiliary unit does notprovide for mixing of hot andcold air. Adjustment oftemperature in the rear may beaccomplished by increasing ordecreasing the rear fan speed...

USING YOUR AUDIO SYSTEM AM/FM Stereo AM/FM Stereo 1 2 3 4 AM/FM SEEK TONE CLK TUNE TONE VOL 12 FM ST DX VOL PUSH ON 1 2 3 4 AM/FM SEEK TONE CLK TUNE TONE VOL 12 FM ST DX VOL PUSH ON AM / FM STEREO Controls and features 23

Volume/power control Press the control to turn the audiosystem on or off. Turn the control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition switch is turned back on. AM/FM s...

Tune adjust in radio mode • Press to move to the next frequency down the band(whether or not a listenablestation is located there). Hold thecontrol to move through thefrequencies quickly. • Press to move to the next frequency up the band (whether or not a listenable station is located there). Hold f...

Setting the clock To set the hour, press and hold theCLK control and press: • to decrease hours and • to increase hours. To set the minute, press and holdthe CLK control and press: • to decrease minutes and • to increase minutes. TONE CLK SEEK SEEK TUNE TUNE TONE CLK SEEK TUNE SEEK TUNE Controls and...

AM/FM stereo cassette Volume/power control Press the control to turn the audiosystem on or off. Turn the control to raise or lowervolume. If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition switch is t...

Scan function The scan function works in radiomode. Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stationson the frequency band. Press the SCAN control again to stop the scanmode. Radio station memory preset The radio is equipped with six station memor...

Treble adjust The treble adjust control allows youto increase or decrease the audiosystem’s treble output. Speaker balance adjust Speaker sound distribution can beadjusted between the right and leftspeakers. Speaker fade adjust Speaker sound can be adjustedbetween the front and rearspeakers. Tape se...

Automatic Music Search The Automatic Music Search featureallows you to quickly locate thebeginning of the tape selectionbeing played or to skip to the nextselection. To activate the feature, momentarilydepress the TAPE AMS button.Then, press either REW (for thebeginning of the current selection) or ...

Eject function Press the control to stop and eject atape. Dolby T noise reduction Dolby t noise reduction operates only in tape mode. Dolby t reduces the amount of hiss and static duringtape playback. Press the control to activate (and deactivate) Dolby t noise reduction. The noise reduction system ...

To set the minute, press and holdthe CLK control and press: • to decrease minutes and • to increase minutes. Premium AM/FM Stereo/Cassette/Premium Sound Your audio system is equipped with selective lighting, a unique lightingstrategy. This lighting feature is operable when the headlamps areilluminat...

• to increase volume compensation • to decrease or shut off the volume compensation AM/FM select The AM/FM select control worksin radio, tape and CD modes(if equipped). AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press thecontrol to switch between AM, FM1 o...

Tune adjust for CD changer • Press to select the previous disc in the CD changer. (Play willbegin on the first track of thedisc unless the CD changer is inshuffle mode.) Refer to Shuffle feature for more information. Hold the control to continue reversing through the disc. • Press to select the next...

Scan function The scan function works in radio,tape or CD mode (if equipped). Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stationson the frequency band. Press the SCAN control again to stop the scanmode. Scan function in tape mode Press the SCAN cont...

Autoset memory preset Autoset allows you to set strong radio stations without losing youroriginal manually set preset stations. This feature is helpful on tripswhen you travel between cities with different radio stations. Starting autoset memory preset 1. Select a frequency using the AM/FM select co...

Speaker balance adjust Speaker sound distribution can beadjusted between the right and leftspeakers. Press the BAL control. Use the SELcontrol to adjust the sound betweenthe speakers. Speaker fade adjust Speaker sound can be adjustedbetween the front and rearspeakers. Press the FADE control. Use the...

• In CD mode, pressing the REW control for less than three secondsresults in slow rewind. Pressing the control for more than threeseconds results in fast rewind. Fast forward The fast forward control works intape and CD modes (if equipped). • In the tape mode, tape directionwill automatically revers...

Compression feature Compression adjust brings soft andloud CD passages together for amore consistent listening level. Press the COMP control to activateand deactivate compression adjust. The effect of the feature varies with the music content. Shuffle feature The shuffle feature operates in CDmode a...

If the volume is set above a certain level and the ignition is turned off,the volume will come back on at a “nominal” listening level when theignition switch is turned back on. AM/FM select The AM/FM select control works inradio, tape and CD modes. AM/FM select in radio mode This control allows you ...

Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns,indicating the station is held in memor...

To deactivate autoset and return to your audio system’s manually setmemory stations, press the AUTO control again. Bass adjust The bass adjust control allows youto increase or decrease the audiosystem’s bass output. Press the BASS control then press: • to decrease the bass output and • to increase t...

Press the BAL control then press: • to shift sound to the left and • to shift sound to the right. Speaker fade adjust Speaker sound can be adjustedbetween the front and rearspeakers. Press the FADE control then press: • to shift the sound to the front and • to shift the sound to the rear. Tape/CD se...

Dolby noise reduction manufactured under license from DolbyLaboratories Licensing Corporation. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. Compression adjust Compression adjust brings soft andloud CD passages together for amore consistent listening lev...

To set the minute, press and holdthe CLK control and press TUNE: • to decrease minutes and • to increase minutes. If your vehicle has a separate clockmodule, (other than the digital radiodisplay), the CLK button will notfunction in the above manner. The CLK button will allow you toswitch between med...

The magazine does not need to befull for the changer to operate. Radio power must be turned on to play the CDs in the changer. Themagazine may be stored in the glove compartment when not being used. The CD magazine may be inserted or ejected with the radio power off. Troubleshooting the CD player (i...

Radio reception factors Three factors can affect radio reception: • Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km(24 miles). This range can be affected by “signal modulation.” Signalmodulation is a process...

5. START, cranks the engine. Release the key as soon as the enginestarts. HAZARD FLASHER For information on the hazard flasher control, refer to Hazard flasher in the Roadside emergencies chapter. TURN SIGNAL CONTROL • Push down to activate the leftturn signal. • Push up to activate the right turnsi...

To turn speed control off • Press OFF or • Turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speedwill be erased. To set a speed • Press SET/SET ACC/SET ACCEL.For speed control to operate, thespeed control must be ON andthe vehicle speed must be greater...

To disengage speed control • Depress the brake pedal. Disengaging the speed control willnot erase the previouslyprogrammed set speed. Pressing OFF will erase thepreviously programmed set speed. To return to a previously set speed • Press RES/RSM/RESUME. ForRES/RSM/RESUME to operate,the vehicle speed...

TILT STEERING Pull the tilt steering control towardyou to move the steering wheel upor down. Hold the control whileadjusting the wheel to the desiredposition, then release the control. Never adjust the steering wheel when the vehicle is moving. WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield ...

Push the control on the end of thestalk to activate washer. Push andhold for a longer wash cycle. Thewasher will automatically shut offafter ten seconds of continuous use. OVERDRIVE CONTROL Activating overdrive (Overdrive) is the normal drive position for the best fuel economy. The overdrive functio...

INTERIOR LAMPS Cargo and dome lamps Rear cargo lamps equipped with anON/OFF/DOOR control will lightwhen: • the doors are closed and thecontrol is in the ON position. • the control is in the DOORposition and any door is open. • the headlamp control is rotatedfully counterclockwise. When the control i...

• Press the bottom portion of therocker switch to open. POWER DOOR LOCKS (IF EQUIPPED) Press U to unlock all doors and L tolock all doors. Memory lock If you lock your doors with the power lock switch or the remotetransmitter while the sliding door is open, the door will automaticallylock after it i...

POWER SIDE VIEW MIRRORS (IF EQUIPPED) To adjust your mirrors: 1. Select to adjust the left mirror or to adjust the right mirror. 2. Move the control in the directionyou wish to tilt the mirror. 3. Return to the center position to lock mirrors in place. REMOTE ENTRY SYSTEM (IF EQUIPPED) The remote en...

• Type B Press this control to unlock thedriver’s door. The interior lamps willilluminate. Press the control a second timewithin three seconds to unlock alldoors. Locking the doors • Type A Press this control to lock all doors. To confirm all doors are closed andlocked, press the control a secondtim...

To replace the batteries: 1. Twist a thin coin between the twohalves of the transmitter near thekey ring. DO NOT TAKE THEFRONT PART OF THETRANSMITTER APART. 2. Place the positive (+) side of newbatteries down. Refer to the diagraminside the transmitter unit. 3. Snap the two halves backtogether. Repl...

Replacement of the battery will not cause the remote transmitter to become deprogrammed from your vehicle. The remote transmitter shouldoperate normally after battery replacement. Replacing lost transmitters • Type A Take all your vehicle’s transmittersto your dealer if service is required. If you p...

Illuminated entry The interior lamps illuminate when the remote entry system is used tounlock the door(s) or sound the personal alarm. The system automatically turns off after 25 seconds or when the ignitionis turned to the RUN or ACC position. The dome lamp control(if equipped) must not be set to t...

SEATING Adjusting the front manual seat Never adjust the driver’s seat or seatback when the vehicle ismoving. Do not pile cargo higher than the seatbacks to avoid injuringpeople in a collision or sudden stop. Always drive and ride with your seatback upright and the lapbelt snug and low across the hi...

Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle ismoving. Do not pile cargo higher than the seatbacks to avoid injuringpeople in a collision or sudden stop. Always drive and ride with your seatback upright and the lapbelt snug and low across t...

Always latch the vehicle seat to the floor, whether the seat isoccupied or empty. If not latched, the seat may cause injury during a sudden stop. Quick release captains chair To remove the seats: 1. Disengage the lap/shoulder beltfrom the seat by inserting a key orsmall screwdriver into the slot in ...

2. Pull the seat latch handle, thenpull the seat toward the right side ofthe vehicle to disengage four pinsfrom the floor mount. 3. Remove the seat. To install the seats: Check to see that the seat and seatback is latched securely inposition. Keep floor area free of objects that would prevent proper...

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child from injury in a collision. All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even when an air bag SRS is provided. It is extremely...

2. To unfasten, push the releasebutton and remove the tongue fromthe buckle. The front and rear outboard safety restraints in the vehicle arecombination lap and shoulder belts. The front and rear seat passengeroutboard safety belts have two types of locking modes described below: Vehicle sensitive m...

How to use the automatic locking mode • Buckle the combination lap andshoulder belt. • Grasp the shoulder portion andpull downward until the entirebelt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clickingsound. This indicates the safety belt is now in the automat...

The safety belt pretensioner uses the same crash sensor system as theair bag supplemental restraint system (SRS). When the safety beltpretensioner deploys, webbing from the lap and shoulder safety belt istightened. Front safety belt height adjustment Your vehicle has safety belt heightadjustments fo...

Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a right angle to the beltand pull across your lap until itreaches the buckle. To tighten thebelt, pull the loose end of the beltthrough the tongue until it ...

Conditions of operation If... Then... The driver’s safety belt is notbuckled before the ignitionswitch is turned to the ONposition... The safety belt warning lightilluminates for one to two minutes andthe warning chime sounds for four toeight seconds. The driver’s safety belt isbuckled while the ind...

Steps you can take to properly position yourself away from the airbag: • Move your seat to the rear as far as you can while still reaching thepedals comfortably. • Recline the seat slightly (one or two degrees) from the uprightposition. Do not put anything on or over the air bag module. Placingobjec...

How does the air bag supplemental restraint system work? The air bag SRS is designed toactivate when the vehicle sustainssufficient longitudinal decelerationsufficient to cause the sensors toclose an electrical circuit thatinitiates air bag inflation. The fact that the air bags did notinflate in a c...

Several air bag system components get hot after inflation. Do nottouch them after inflation. If the air bag is deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in acollision. The SRS c...

Disposal of air bags and air bag equipped vehicles For disposal of air bags or air bag equipped vehicles, see your localdealership or qualified technician. Air bags MUST BE disposed of byqualified personnel. SAFETY RESTRAINTS FOR CHILDREN See the following sections for directions on how to properly ...

Do not use a forward–facing safety seat or an infant seat in the last row of a 12– or 15–passenger Club Wagon. Children and safety belts If the child is the proper size, restrain the child in a safety seat. Children who are too large for child safety seats (as specified by yourchild safety seat manu...

SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of thechild. Carefully follow all of the manufacturer’s instructions with thesafety seat you put in your vehicle. If you do not install and use thesafety seat properly, the ...

Ford recommends the use of a child safety seat having a top tetherstrap. Install the child safety seat in a seating position which is capableof providing a tether anchorage. For more information on top tetherstraps, refer to Attaching safety seats with tether straps. Carefully follow all of the manu...

Attaching safety seats with tether straps Some manufacturers make safety seats that include a tether strap thatgoes over the back of the vehicle seat and attaches to an anchoringpoint. Other manufacturers offer the tether strap as an accessory.Contact the manufacturer of your child safety seat for i...

Rear seating positions Attachment holes have been provided in your vehicle to attach anchorhardware, if required. Tether anchor hardware kits (Part No. 613D74)including instructions, may be obtained at no charge from any Forddealer. • Second row bucket seats (at rearof lower seat frame) • 3–passenge...

PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meetsall Canadian Interference-Causing Equipment standard requirementsregulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerato...

Make sure the corresponding lights illuminate briefly. If a light fails toilluminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light will not illuminate. STARTING THE ENGINE 1. Turn the key to 5 (START)without pressing the acceleratorpedal and release as soon as thee...

Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improvesstarting, warms up the engine faster and allows the heater-defrostersystem to respond quickly. Use of an engine block heater is stronglyrecommended if you live in a region where temperatures re...

Important ventilating information If the engine is idling while the vehicle is stopped in an open area forlong periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning (if equipped) to bring in fresh air. Improve vehicle ventilation bykeeping all air inlet...

BRAKES Your service brakes are self-adjusting. Refer to the “Service Guide” forscheduled maintenance. Occasional brake noise is normal and often does not indicate aperformance concern with the vehicle’s brake system. In normaloperation, automotive brake systems may emit occasional or intermittentsqu...

ABS warning lamp The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned on and the engine is off. If the light does notilluminate momentarily at start up, remains on or continues to flash, theABS needs to be serviced. With the ABS light on, the anti-lockbr...

RABS warning lamp The ABS warning lamp in the instrument cluster illuminates if a RABS fault is detected. Have your vehicle serviced as soon as possible. Normal braking is still effectiveunless the BRAKE warning lamp isalso illuminated. Using RABS • In an emergency, applying full pressure may cause ...

• Type B Pull the release lever to release theparking brake. Driving with theparking brake on will cause thebrakes to wear out quickly andreduce fuel economy. STEERING Your vehicle is equipped with power steering. Power steering uses energyfrom the engine to help steer the vehicle. To prevent damage...

TRACTION-LOK AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly whenone wheel is on a poor traction surface. Under normal conditions, theTraction-Lok axle functions like a standard rear axle. Extended use of other than the manufacturer’s specified size tires on a...

Do not rock the vehicle for more than a few minutes. Thetransmission and tires may be damaged or the engine mayoverheat. Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn off the ignition whenever you leave your vehicle. If the parking brake is fully released...

R (Reverse) With the gearshift in R (Reverse),the vehicle will move backward.Always come to a complete stopbefore shifting into and out of R(Reverse). N (Neutral) With the gearshift in N (Neutral),the vehicle can be started and isfree to roll. Hold the brake pedaldown while in this gear. (Overdrive)...

• GCWR (Gross Combined Weight Rating) : Maximum combined weight of towing vehicle (including passengers and cargo) and thetrailer. The GCWR indicates the maximum loaded weight that thevehicle is designed to tow. • Maximum Trailer Weight Rating : Maximum weight of a trailer the vehicle is permitted t...

your vehicle including both Gross Vehicle Weight and Front and RearGross Axle Weight Rating limits. Under no circumstance should theselimitations be exceeded. Exceeding any vehicle weight rating limitationcould result in serious damage to the vehicle and/or personal injury. Calculating the load your...

Your vehicle’s load capacity is designated by weight, not by volume, soyou cannot necessarily use all available space when loading a vehicle. Distribute the load so that only 10 to 15% of the total is on the tongue.Tie down the load so that it does not shift and change the weight on thehitch. Towing...

Trailer brakes Electric brakes and manual, automatic or surge-type brakes are safe ifinstalled properly and adjusted to the manufacturer’s specifications. Thetrailer brakes must meet local and Federal regulations. Do not connect a trailer’s hydraulic brake system directly to yourvehicle’s brake syst...

OFF) on moderately steep hills, Second (2) on steep hills, and First (1)on very steep hills. Servicing after towing If you tow a trailer for long distances, your vehicle will require morefrequent service intervals. Refer to your maintenance guide and orservice guide for more information. Trailer tow...

HAZARD LIGHTS CONTROL Use only in an emergency to warn traffic of vehicle breakdown,approaching danger, etc. The hazard flashers can be operated when theignition is off. • The hazard lights control islocated on top of the steeringcolumn. • Depress hazard lights control toactivate all hazard flashers...

For commercial stripped chassisvehicles, the fuel pump shut-offswitch is located on a bracket abovethe brake pedal. FUSES AND RELAYS Fuses If electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check the appropriatefus...

Standard fuse amperage rating and color COLOR Fuse Rating Mini Fuses Standard Fuses Maxi Fuses Cartrigde Maxi Fuses Fuse Link Cartridge 2A Grey Grey — — — 3A Violet Violet — — — 4A Pink Pink — — — 5A Tan Tan — — — 7.5A Brown Brown — — — 10A Red Red — — — 15A Blue Blue — — — 20A Yellow Yellow Yellow ...

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Description 1 20A RABS/4WABS Module 2 15A Brake Warning Diode/Resistor, InstrumentCluster, Warning Chime, 4WABS Relay,Warning Indicators 3 15A Main Light Switch, RKE Module, Radio 4 15A Power Locks w/RKE, Illuminated Entry,Warning C...

CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily.Instead, gradually decrease your speed. Hold the steering wheel firmlyand slowly move to a safe place on the side of the road. Spare tire information The spare tire for your vehicle is stowed under the rear of yo...

3. Raise the tire by turning thewrench or handle clockwise.Continue until the lift mechanism“clicks.” 4. Check that the tire is tightlyseated under the vehicle by pushingagainst the tire. Retighten asnecessary. 5. Replace the access cover,anti-theft bracket and thumb screw. Use finger pressure only ...

6. Remove the spare tire and jackfrom the storage location. 7. Use the tapered end of the lugnut wrench to unscrew wheelornaments attached by retainingscrews. Remove any wheel trim.Insert the tapered end of the lugnut wrench behind wheel covers orhubcaps and twist off. 8. Loosen the wheel nut by pul...

• Never use the front or reardifferential as a jacking point. Rear axle jacking points: • All models except E-Super Duty • E-Super Duty Roadside emergencies 136

Front axle jacking points: • All models Place the jack under the pin on thefront axle. 3. Turn the jack handle clockwise until the wheel is completely off theground. 4. Remove the lug nuts with the lug nut wrench. 5. Replace the flat tire with the spare tire. If your vehicle has single rear wheels, ...

• 8 lug wheel Never use wheels or lugnuts different than the original equipment as this coulddamage the wheel or mountingsystem. This damage could allowthe wheels to come off while thevehicle is being driven. 9. Replace any wheel covers, ornaments or hub caps. Make sure they are screwed or snapped i...

JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames,sparks, or lit cigarettes. An explosion could result in injury or vehicle damage. Do not push start your vehicle. You could damage the catalyticconverter. Batteries contain sulfuric acid which can burn skin, eye...

Connecting the jumper cables 1. Connect the positive (+) booster cable to the positive (+) terminal ofthe discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+)term...

3. Connect the negative (-) cable to the negative (-) terminal of theassisting battery. 4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarburetor. The preferred locations of an exposed metal part (to ground...

Jump starting 1. Start the engine of the booster vehicle and run the engine atmoderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for afurther three minutes before disconnecting the jumper cables. Removing the jumpe...

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of thedisabled vehicle’s battery. After the disabled vehicle has been started and the jumper cablesremoved, allow it to idle for several minutes so the...

WRECKER TOWING If you need to have your vehicle towed, contact a professional towingservice or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbedequipment. A towing manual is available from Ford Motor Company for all autho...

SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easylocation. • We provide a “Service Guide” which makes tracking routine serviceeasy. If your vehicle requires professional service, your dealership can providenecessary parts...

Do not start your engine with the air cleaner removed and donot remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hoodrelease handle located under thebottom left corner of the instrumentpanel. 2. Go to the front of the vehicle and release the auxiliary latch tha...

3. Set the parking brake and ensure the gearshift is securely latched in P(Park). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove theengine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove itagain. • If the oil l...

Adding engine oil 1. Check the engine oil. For instructions, refer to Checking the engine oil in this chapter. 2. If the engine oil level is not within the MIN and MAX ranges, add onlycertified engine oil of the recommended viscosity. Remove the engine oilfiller cap and use a funnel to pour the engi...

BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked andrefilled as needed. Refer to themaintenance guide and or serviceguide for the service intervalschedules: 1. Clean the reservoir cap beforeremoval to prevent dirt or waterfrom entering the reservoir. 2. Visually inspect the ...

If the engine coolant has not been checked at the recommended interval,the engine coolant reservoir may become empty. If this occurs, addengine coolant to the reservoir. For more information on engine coolantmaintenance, refer to Adding engine coolant in this chapter. Automotive fluids are not inter...

Coolant refill capacity To find out how much fluid your vehicle’s cooling system can hold, referto Refill capacities in the Capacities and specifications chapter. Have your dealer check the engine cooling system for leaks if you haveto add more than 1.0 liter (1.0 quart) of engine coolant per month....

Continued operation will increase the engine temperature and the enginewill completely shut down, causing steering and braking effort toincrease. Once the engine temperature cools, the engine can be re-started. Takeyour vehicle to a service facility as soon as possible to minimize enginedamage. When...

CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid.Refer to the maintenance guide andor service guide for the serviceinterval schedules. If adding fluid isnecessary, use only MERCON t ATF. Check the fluid level when it is at ambient temperature, 20° – 80° F(-7° – 25° C): 1. Chec...

6. If the fluid is low, add fluid in small amounts, continuously checkingthe level until it reaches the FULL COLD range. Be sure to put thedipstick back in the reservoir. TRANSMISSION FLUID Checking automatic transmission fluid Refer to your maintenance guide and or service guide for scheduledinterv...

operating temperature can be reached after approximately 30 km(20 miles) of driving. However, you can check the fluid without driving ifthe outside temperatures are above 10°C (50°F). If fluid is added at thistime, an overfill condition could result when the vehicle reaches normaloperating temperatu...

Batteries normally produce explosive gases which can causepersonal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery,always shield your face and protect your eyes. Always provide properventilation. When lifting a plastic-case...

If the battery has been disconnected or a new battery has been installed,the clock and the preset radio stations must be reset once the battery isreconnected. • Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized...

Gasoline engines Disconnect: 1. Disconnect the primary batteryground cable. 2. Disconnect the auxiliary batteryframe ground. • Remove the ground bolt. • Pull the cable away from theframe and make sure that thecable does not contact the frame. Connect: 1. Reconnect the auxiliary batteryframe ground. ...

2. Reconnect the primary batteryground cable. Diesel engines Disconnect: Secondary positive cable remains energized after disconnection.make sure the tool does not contact any ground surface. 1. Disconnect the secondary positivecable from the primary batteryterminal. 2. Wrap the secondary positive c...

WINDSHIELD WIPER BLADES Check the wiper blades at least twice a year or when they seem lesseffective. Substances such as tree sap and some hot wax treatments usedby commercial car washes reduce the effectiveness of wiper blades. Checking the wiper blades If the wiper blades do not wipe properly, cle...

Temperature A B C The temperature grades are A (the highest), B, and C, representing thetire’s resistance to the generation of heat and its ability to dissipate heatwhen tested under controlled conditions on a specified indoor laboratorytest wheel. Sustained high temperature can cause the material o...

Replacing the tires Replace the tires when the wearband is visible through the tiretreads. Failure to follow these precautions may adversely affect thehandling of the vehicle and make it easier for the driver to lose control and roll over. Tires that are larger or smaller than your vehicle’s origina...

• Remove the tire chains when they are no longer needed. Do not usetire chains on dry roads. • The suspension insulation and bumpers will help prevent vehicledamage. Do not remove these components from your vehicle whenusing snow tires and chains. WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Importan...

• Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kindcan lead to eye and respiratory tract irritation. In severe cases,excessive or prolonged breathing of fuel vapor can cause seriousillness and permanent injury. • Avoid getting fuel liquid in your eyes. If fuel is splashed in the e...

Octane recommendations Your vehicle is designed to use“Regular” unleaded gasoline with an(R+M)/2 octane rating of 87. We donot recommend the use of gasolineslabeled as “Regular” that are soldwith octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes knock...

• Your “Service Engine Soon” light may come on. For more informationon the “Service Engine Soon” light, refer to the Instrumentation chapter. Fuel Filler Cap Your fuel tank filler cap has an indexed design with a one-eighth turnon/off feature. When fueling your vehicle: 1. Turn the engine off. 2. Ca...

Filling the tank For consistent results: • Use the same filling rate setting (low — medium — high) each timethe tank is filled. • Allow three automatic click-offs when filling. • Always use the recommended octane rating of a known qualitygasoline, preferably a national brand. • Use the same side of ...

Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fueleconomy. • Idling for long periods of time (greater than one minute) may wastefuel. • Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or...

Conditions • Heavily loading a vehicle or towing a trailer may reduce fuel economyat any speed. • Carrying unnecessary weight may reduce fuel economy (approximately2 km/h [1 mpg] is lost for every 180 kg [400 lb] of weight carried). • Adding certain accessories to your vehicle (for example bugdeflec...

EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to comply withapplicable exhaust emission standards. To make sure that the catalyticconverter and other emission control components continue to workproper...

engine. This decal identifies engine displacement and gives some tune upspecifications. Please consult your “Warranty Guide” for complete emission warrantyinformation. Readiness for inspection/maintenance (I/M) testing In some localities, it may be a legal requirement to pass an I/M test ofthe on-bo...

To install the new bulb: 1. With the flat side of the bulb’splastic base facing upward, insertthe glass end of the bulb into thelamp assembly. You may need toturn the bulb left or right to alignthe grooves in the plastic base withthe tabs in the lamp assembly. Whenthe grooves are aligned, push the b...

High-mount brakelamp bulbs The interior cargo lamp (if equipped) will have to be removed fromunder the high-mount brakelamp assembly located inside the vehicle. To change the high-mountbrakelamp bulbs: 1. Remove the two screws from thehigh-mount brakelamp assembly. 2. Remove the bulb from the lampas...

Using the right bulbs Function Number of bulbs Trade number Headlamps (low series) 2 H5054 Headlamps (high series) 2 9007 Park lamp and turn signal (front) 2 3157 NAK Back-up lamps 2 3156K License plate lamps 1 168 Stop/tail/side marker lamp 2 3357 K Turn lamp (rear) 2 3156K High-mount brakelamp 2 9...

Washing your vehicle Wash your vehicle regularly withcold or lukewarm water. Never usestrong detergents or soap. If yourvehicle is particularly dirty, use aquality car wash detergent. Alwaysuse a clean sponge, washing gloveor similar device and plenty of waterfor best results. To avoid spots,avoid w...

Cleaning plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover ifnecessary. Do not clean plastic parts with thinners, solvents orpetroleum-based cleaners. Cleaning the exterior lamps Wash with the same detergent as the exterior of your vehicle. Use glasscleaner or t...

Cleaning and maintaining the safety belts Clean the safety belts with a mild soap solution recommended forcleaning upholstery or carpets. Do not bleach or dye the belts, becausethese actions may weaken the belt webbing. Check the safety belt system periodically to make sure there are nonicks, wear o...

MOTORCRAFT PART NUMBERS Com-ponent* 4.2L V6engine 4.6L V8engine 5.4L V8engine 6.8L V10engine Air filter FA-1634 FA-1634 FA-1634 FA-1634 Battery(standard) BXT-65-650 BXT-65-650 BXT-65-650 BXT-65-650 Battery(optional) BXT-65-750 BXT-65-750 BXT-65-750 BXT-65-750 Battery(auxiliary) BH-65DC BH-65DC BH-65...

REFILL CAPACITIES Fluid Ford PartName Application Capacity Brake fluid HighPerformanceDOT 3 MotorVehicle BrakeFluid All Fill to line onreservoir Engineoil-gasolineengine (includesfilter change) Motorcraft 5W30Super PremiumMotor Oil All 5.7L(6.0 quarts) Engine oil-dieselengine (includesfilter change)...

Fluid Ford PartName Application Capacity Power steeringfluid MotorcraftMERCON t ATF All Keep in FULLrange ondispstick Rear axle Refer tofootnote 4 Ford 8.8/9.75 inchconventional andTraction-Lok 2.6-2.7L(5.5-5.8 pints) 2 Dana 9.75 inch(M60-IU) 3.0L (6.3 pints) 3 Dana 10.5 inch(M70-2U) 3.1L (6.6 pints...

Fluid Ford PartName Application Capacity Transmission 6 MotorcraftMERCON t V ATF Automatic(4R70W) 13.1L(13.9 quarts) MotorcraftMERCON t ATF Automatic(4R100) 7 15.0L(15.9 quarts) 8 Windshieldwasher fluid Ultra-ClearWindshieldWasherConcentrate All Fill to line onreservoir If your vehicle’s rear axle i...

LUBRICANT SPECIFICATIONS Item Ford partname Ford partnumber Fordspecification Brake fluid High Perfor-mance DOT 3Motor VehicleBrake Fluid C6AZ-19542-AB ESA-M6C25-Aand DOT 3 Doorweatherstrips SiliconeLubricant C0AZ-19553-AAandF5AZ-19553-AA ESR-M13P4-A Engine coolant Ford PremiumEngine Coolant(green i...

Item Ford partname Ford partnumber Fordspecification Parking brakeassembly(E-Super Duty) MotorcraftMERCON t AutomaticTransmissionFluid XT-2-QDX MERCON t Fordconventional andTraction-Lokaxles (E-150) 2 Motorcraft SAE75W140 HighPerformanceSynthetic rearaxle lubricant F1TZ-19580-B WSL-M2C192-A Dana con...

ENGINE DATA Engine* 4.2L V6engine 4.6L V8engine 5.4L V8engine 6.8L V10engine Cubic inches 256 281 330 415 Horsepower 200 @4800 rpm 215 @4500 rpm 235 @4450 rpm 265 @4250 rpm Torque 250 lb.-ft. @2800 rpm 290 lb.-ft. @3250 rpm 335 lb.-ft. @3000 rpm 405 lb.-ft. @2750 rpm Recom-mended fuel 87 octane 87 o...

Cutaway/commercial stripped chassis models E-250 E-350 E-Super Duty (1) Overallheight Refer to Body Builder for specifications (2) Trackfront/rear 1 762.8 mm(69.4 in)/1 701.8 mm(67.0 in) 1 762.8 mm(69.4 in.)/SRW 1 701.8mm (67.0 in.),DRW 1 859.3mm (73.2 in.) 1 762.8 mm(69.4 in.)/1 973.6 mm(77.7 in.) ...

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle hasa defect that could cause a crash, orcould cause injury or death, youshould immediately inform theNational Highway Traffic SafetyAdministration (NHTSA) in additionto notifying Ford Motor Company. If NHTSA receives similar compl...

Air bag supplemental restraintsystem ..........................................83 and child safety seats ..............84description ................................83disposal ......................................87indicator light ...........................86passenger air bag ........................

Steering wheel tilting .........................................61 Tires ....................................166,167 changing ...........................132,133checking the pressure ............167replacing ...........................135,169rotating ....................................167snow tires ...

Recommended fuel Unleaded fuel only - 87 octane Fuel tank capacity Refer to Refill capacities in the Capacities and specifications chapter. Engine oilcapacity-gasoline engine(includes filter change) 5.7L (6.0 quarts). Use Motorcraft 5W30Super Premium Motor Oil, Fordspecification WSS-M2C153-G. Engine...