Fisher-Price H5988 - Manuals

Fisher-Price H5988 – Manual in PDF format online.

Manuals:

Manual

Manual Fisher-Price H5988

Summary

Page 2 - WARNING; All Shown Actual Size; Tighten or loosen all screws with a; Parts; Please remove all parts from the package and; CAUTION

2 2 WARNING To prevent serious injury or deathfrom falls and being strangled inthe restraint system: • Always use the restraint system. Never rely on the tray to restrain child. • Never use with an active child who may be able to climb out of the seat. • Not recommended for children who can sit up b...

Page 3 - You may need the help of another adult to help you balance; Assembly

IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. 3 3 1 Button Leg Housing • Place a housing on a f...

Page 4 - • Set the frame assembly aside.; CORRECT

4 4 HUBS FACING OUT FRONTBASECURVESINWARD HUBS FACING IN • Check to be sure you have assembled the leg assemblies to the bases correctly. Please refer to the illustrations above.• If the leg assemblies are assembled incorrectly to the bases, simply pull the legs from the bases. Please re-read and re...

Page 5 - Look at opening in the straight end of the tube. It should be round.; Look at opening in the straight end of the tube. It should be oval.

5 5 5 • Align the hole in the seat tube with the hole in the armrest.• Insert a 3.8 cm pin screw through the armrest and into the seat tube. Tighten the screw. 6 Seat Bottom Round EndSeat Tube Armrest Holes • Position the seat bottom so that the back faces you and the armrest holes are facing up. • ...

Page 6 - outside

6 9 Seat Back • Fit the seat back to the seat bottom. Seat Bottom 10 Rod • Insert the rod into the side opening between the seat back and seat bottom. • Insert a #8 x 1.9 cm screw into the opening in the rod and tighten. #8 x 1.9 cm Screw Assembly 11 • Fit the seat back wire through the raised slots...

Page 7 - “snap”

7 14 Seat Tubes • Insert the ends of the seat tubes into the holes in the hubs.• Push the seat tubes in until you hear a “snap” (for each). • Push down on the seat to be sure the seat is secured in both frame hubs. Hubs 13 • Attach a lock nut, rounded side facing out, onto one end of a seat back wir...

Page 8 - • From under the seat, fit the elastic loops onto the tabs; • From behind the seat, fit the pad elastic loops to the tabs on

8 16 • Place the pad onto the seat.• Insert the pad elastic loops through the holes in the seat bottom. • From under the seat, fit the elastic loops onto the tabs on the seat back. Elastic Loops Tabs Holes Assembly 17 Waist Belts • Insert the waist belts through the slots in the pad.• Fit the top of...

Page 9 - • Fit the toybar hubs to the seat tubes.; Assembly is now complete.; • Fit and; the tray onto the seat armrests.

9 Assembly 19 • Fit the crotch belt through the slot in the pad.• Fit the pad side clips around the edge of the seat bottom.• Fit the pad elastic loops around the front edge of the seat bottom. Attach the pad elastic loops to the tabsunderneath the seat bottom. Crotch Belt Slot Clips Elastic Loops T...

Page 10 - Swing; alkaline; We recommend using; Battery Installation

1,5V x 4 “D” (LR20) • Loosen the screws in the battery compartment door and remove the battery compartment door. • Insert four “D” (LR20) alkaline batteries into the battery compartment. • Replace the battery compartment door and tighten the screws. Swing Toybar • Loosen the screws in the battery co...

Page 11 - • Do not mix old and new batteries or batteries of different; Before each use, inspect this product for damaged

11 Battery Safety Information Setup and Use Batteries may leak fluids that can cause a chemical burninjury or ruin your product. To avoid battery leakage: • Do not mix old and new batteries or batteries of different types: alkaline, standard (carbon-zinc) or rechargeable(nickel-cadmium). • Insert ba...

Page 12 - Setup and Use; Make sure you; As with most battery-powered swings, a heavier child will reduce; TIGHTEN; Securing your Infant

12 12 Setup and Use 1 Waist Belts Crotch Belt • Place your child in the seat. Position the crotch belt between your child’s legs. • Fasten the waist belts to the crotch belt. Make sure you hear a “click” on both sides. • Check to be sure the restraint system is securely attached by pulling it away f...

Page 13 - • Lift or lower the seat wire into the grooves on the seat back.; Adjusting the Seat; • Slide the lights switch to

13 Setup and Use Adjust the seat angle to any of three positions: Upright,Semi-Recline or Recline. To adjust the seat angle: • Lift or lower the seat wire into the grooves on the seat back. Seat Wire RECLINE SEMI- RECLINE UPRIGHT 4 Adjusting the Seat Using the Toy Bar 5 Volume Switch Lights Switch L...

Page 14 - If sounds or lights slow or dim or turn off altogether, it’s time; Parent Activated

14 Setup and Use 6 Mode Switch Mode Switch Mode Switch • Slide the mode switch to Parent Activated. • Baby enjoys 10 minutes of music along with twinkling lights (if lights switch is turned on). • Slide the mode switch to to turn the toybar off. Hint: If sounds or lights slow or dim or turn off alto...

Page 15 - Storage; • The pad, frame and toy bar may be wiped clean using a mild; Care; • Remove the four pad elastic loops from the seat back and; • Press the button on each housing and push the rear legs

15 Storage • The pad, frame and toy bar may be wiped clean using a mild cleaning solution and a damp cloth. Do not use bleach. Do notuse harsh or abrasive cleaners. Rinse clean with water toremove residue. Care 1 To remove the pad: • Remove the four pad elastic loops from the seat back and bottom ta...

Page 16 - Consumer Information

GREAT BRITAIN Helpline: 01628 500302. Or write to: Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB. AUSTRALIA Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia. Consumer Advisory Service1300 135 312. ASIA Mattel East Asia Ltd, Room 1106, South...