Fisher-Price H4792 - Manuals

Page 2 - WARNING; Never rely on the tray to restrain child.; All Shown Actual Size; Tighten or loosen all screws with a; Parts

2 2 WARNING To prevent serious injury or deathfrom falls and being strangled inthe restraint system:• Always use the restraint system. Never rely on the tray to restrain child. • Never use with an active child who may be able to climb out of the seat. • Not recommended for children who can sit up by...

Page 3 - You may need the help of another adult to help you balance; Assembly; CAUTION; This package contains small parts

IMPORTANT! Before assembly, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. 3 3 1 Button Leg Housing • Place a housing on a f...

Page 4 - • Set the frame assembly aside.; CORRECT

4 3 HUBS FACING OUT FRONTBASECURVESINWARD HUBS FACING IN • Check to be sure you have assembled the leg assemblies to the bases correctly. Please refer to the illustrations above.• If the leg assemblies are assembled incorrectly to the bases, simply pull the legs from the bases. Please re-read and re...

Page 5 - Look at opening in the straight end of the tube. It should be; Look at opening in the straight end of the tube. It should be oval.

5 5 4 • Align the hole in the seat tube with the hole in the armrest.• Insert a 3.8 cm pin screw through the armrest and into the seat tube. Tighten the screw. 5 Seat Bottom Round EndSeat Tube Armrest Holes • Position the seat bottom so that the back faces you and the armrest holes are facing up. • ...

Page 6 - • Fit the seat back to the seat bottom.; • Insert the rod into the side opening between the seat back; • Fit the seat back wire through the raised slots on the seat back.; • Fit the ends of the seat back wire into the outside holes in

6 8 Seat Back • Fit the seat back to the seat bottom. Seat Bottom 9 Rod • Insert the rod into the side opening between the seat back and seat bottom. • Insert a #8 x 1.9 cm screw into the opening in the rod and tighten. #8 x 1.9 cm Screw Assembly 10 • Fit the seat back wire through the raised slots ...

Page 7 - “snap”

7 13 Seat Tubes • Insert the ends of the seat tubes into the holes in the hubs.• Push the seat tubes in until you hear a “snap” (for each). • Push down on the seat to be sure the seat is secured in both frame hubs. Hubs 12 • Attach a lock nut, rounded side facing out, onto one end of a seat back wir...

Page 8 - • From under the seat, fit the elastic loops onto the tabs; • From behind the seat, fit the pad elastic loops to the tabs on

8 15 • Place the pad onto the seat.• Insert the pad elastic loops through the holes in the seat bottom. • From under the seat, fit the elastic loops onto the tabs on the seat back. Elastic Loops Tabs Holes Assembly 16 Waist Belts • Insert the waist belts through the slots in the pad.• Fit the top of...

Page 9 - • Fit the toybar hubs to the seat tubes.

9 Assembly 18 • Fit the crotch belt through the slot in the pad.• Fit the pad side clips around the edge of the seat bottom.• Fit the pad elastic loops around the front edge of the seat bottom. Attach the pad elastic loops to the tabsunderneath the seat bottom. Crotch Belt Slot Clips Elastic Loops T...

Page 10 - Assembly is now complete.; • Fit and; the tray onto the seat armrests.; the tray links into the holes in the tray.

10 Assembly is now complete. 20 Tray 21 • Fit and “snap” the tray onto the seat armrests. • Insert and “snap” the tray links into the holes in the tray. Tray Links • Fit the toy links and/or toys on the toy bar/tray! Assembly

Page 11 - alkaline; We recommend using; Battery Installation; Battery Safety Information

11 1,5V x 4 “D” (LR20) • Loosen the screws in the battery compartment door and remove the battery compartment door. • Insert four “D” (LR20) alkaline batteries into the battery compartment. • Replace the battery compartment door and tighten the screws. Hint: We recommend using alkaline batteries for...

Page 12 - Setup and Use; Securing your Infant; TIGHTEN

12 12 Setup and Use 1 Waist Belts Crotch Belt Securing your Infant • Place your child in the seat. Position the crotch belt between your child’s legs. • Fasten the waist belts to the crotch belt. Make sure you hear a “click” on both sides. • Check to be sure the restraint system is securely attached...

Page 13 - Swinging; As with most battery-powered swings, a heavier child will reduce; Music; Low battery power may cause product movement to slow; • Lift or lower the seat wire into the grooves on the seat back.

13 Setup and Use Power Switch Music Button Swinging • Make sure your child is properly secured in the seat.• Slide the swing power switch on to any of six speed settings.• Watch the toys move when the seat swings!• Be sure to slide the switch to the off position when the swing is not in use. Hint: A...

Page 14 - Using the Toy Bar; • Lift or lower the toy bar for baby’s enjoyment.; Care; • Remove the four pad elastic loops from the seat back and

14 Setup and Use Toy Bar Using the Toy Bar • Lift or lower the toy bar for baby’s enjoyment. Hint: The toys move when the swing is turned on! 5 • The pad is machine washable. Wash it separately in cold water on the gentle cycle. Do not use bleach. Line dry only. •The frame, links, toys and toy bar m...

Page 15 - the front legs. Stand the frame against a wall for storage.; Storage; AUSTRALIA; Consumer Information

15 • Push the toy bar backward to its storage position.• Press the button on each housing and push the rear legs toward the front legs. Stand the frame against a wall for storage. Toy Bar PRESS BUTTON Storage GREAT BRITAINMattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB.Helpline: 01628 50030...