Fisher & Paykel DD90STI2 - Manuals

5 ADDITIONAL PARTS SUPPLIED WITH INTEGRATED MODELS 3b External Venting kit (1) supplied with Integrated models with remote (NZ AU) only Panel mounting screws (14) Panel bracket (1) (attached to product) Integrated rectangular badge (1) (Satin chrome supplied) supplied with Integrated models with bad...

6 4 PRODUCT DIMENSIONS A H I J K Side Plan G F B C D E Product dimensions (mm) Desig ner In te grate d Remote contr ol In te grate d Badge c ontr ol A overall height 1 of product (incl. front panel height) 478 478 478 B overall width of product 895 min. 855 min. 855 C overall depth of product (excl....

7 5 CABINETRY DIMENSIONS Plan Side L M P ON 18 mm 20 mm 2 mm ON Minimum clearances from adjacent cabinetry Cabinetry dimensions mm Desig ner In te grate d Remote contr ol In te grate d Badge c ontr ol L height of cavity (from support surface to undersideof benchtop) 480 480* 480* M inside height of ...

8 The following calculations assume the top of the panel is aligned with the top of the adjacent cabinetry: WIDTH OF THE PANEL Measure A ( the width between adjacent door/drawer fronts) and write it in the fi rst box below, then complete the equation. HEIGHT OF THE PANEL Measure B and write it in th...

9 The following calculations assume the top of the panel is aligned with the top of the adjacent cabinetry: WIDTH OF THE PANEL Measure A ( the width between adjacent door/drawer fronts) and write it in the fi rst box below, then complete the equation. HEIGHT OF THE PANEL Measure B and write it in th...

10 7a CAVITY PREPARATION Water Connection Recommended COLD (Maximum 60°C). ¾ “ BSP (GB20) to suit flat washer. Water Pressure Water softener models Max. 1 MPa (145 psi)Min. 0.1 MPa (14.5 psi) Models without water softener Max. 1 MPa (145 psi)Min. 0.03 MPa (4.3 psi) Important! Adjacent cabinetry must...

11 7b 7c INTEGRATED MODELS WITH REMOTE (NZ AU) ONLY - PREPARATION FOR EXTERNAL VENTING THROUGH SAME CABINET INTEGRATED MODELS WITH REMOTE (NZ AU) ONLY - PREPARATION FOR EXTERNAL VENTING THROUGH ADJACENT CABINET ø 60 mm ø 60 mm max. 5 mm max. 5 mm 220 mm 220 mm 100 mm 100 mm ø60mm Services can be loc...

12 8 MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGE Left hand side Right hand side Drain hose - 2000 mm Inlet hose - 1650 mm Venting hose - 1265 mm Venting hose - 1925 mm (Integrated models only) (Integrated models only) Power cord (excl. plug) - 750 mm Power cord (excl. plug) - 400 mm Drain...

15 12a 11a PULL THROUGH HOSES & MOVE INTO THE CAVITY SECURE THE DRAWER 1 3 2 Open the drawer halfway. Using a flat-bladed screwdriver, prise the grey rubber plug out of the trim moulding. Replace the grey rubber plug back intothe trim moulding and ensure the trimseal is facing forward. Repeat fo...

22 ADJUST PANEL HEIGHT TO ALIGN THE CABINETRY GAPS Insert an appropriately sized Philips screwdriver into the hole above the door pin and rotate the panel up or down to align the gaps in your cabinetry. Repeat on the other side if necessary. The panel has a maximum travel of 2 mm up or down. Importa...

23 THERE ARE TWO DIFFERENT PLUMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE. 22 1 3 2 750-882.5 mm 1 2 38 mm max. 120 mm 750-882.5 mm * * 3 4 5 If space is limited for fixing, push hose through drain hose support to required height If space is limited for fixing, push hose through drain ...

24 26 25 FINAL CHECKLIST TROUBLESHOOTING Check all parts are installed. Ensure product is level, securely fastened to the cabinetry and opens and closes freely. The drawer must be free to fully close with no resistance from the cabinetry. Ensure inlet hose to water supply has supplied rubber washer ...