Fisher & Paykel DD60SDFTB9 - Manuals

4 4 CABINETRY DIMENSIONS Minimum clearances from adjacent cabinetry min. 13 mmclearance from a cornercupboard Bracket slots min. 2 mmclearance to adjacent cupboard door R Q P S T PROFILE PLAN DD60DDF CABINETRY DIMENSIONS MM P Inside height of cavity* min. 820 Q Inside width of cavity 600 R Inside de...

5 Moisture protection tape must be applied. 10 mm COUNTERTOP 5 CAVITY PREPARATION Water Connection Recommended COLD (Maximum 60°C). 3/4“ BSP (GB20) to suit flat washer. Kosher requirements Drains will need to be separated to satisfy kosher requirements. We suggest you confirm acceptability with your...

6 6 MAXIMUM DISTANCE OF HOSES & CORD FROM CHASSIS EDGE LEFT HAND SIDE Drain hoses—2000mm Drain hoses—1800mm Inlet hose—1650mm Inlet hose—1250mm Power cord (excl.plug)—1650mm Power cord (excl.plug)—1650mm RIGHT HAND SIDE

7 (x2) 7 RECOMMENDED METHOD (A) — SECURE WITHOUT DRAWER REMOVAL (FRAMELESS CABINETRY ONLY) NOW CHOOSE WHICH INSTALLATION METHOD (A) OR (B) IS MORE SUITABLE FOR YOUR CABINETRY... As you push product in, pull through hoses and cord, ensuring they don’t get kinked or twisted. Optionally attach the two ...

9 (x2) 1 2 4 4 3 3 7 ALTERNATIVE METHOD (B) — SECURE BY DRAWER REMOVAL As you push product in, pull through hoses and cord, ensuring they don’t get kinked or twisted. optionally attach the two top mounting brackets Initially level the product You can raise or lower the product by twisting the feet. ...

11 !3 FIT THE SUPPLIED TOEKICK PANEL 19 1 3 5 7 8 9 2 6 4 19 IMPORTANT! Do not overtighten screw. Where the toekick meets the bottom of the tub is the cut-off point Mark this point on the toekick with a pencil Lay the toekick face down on a chopping board or similiar Smooth the edges with a file. Be...

13 Ensure the supplied rubber washer is fitted inside the coupling. Tighten coupling with spanner. 180 o No leaks! 1 2 min. 10mm 3/4” BSP connector !5 CONNECT INLET HOSE TO COLD WATER !6 PLUG PRODUCT IN !7 TROUBLESHOOTING O Excessive water remaining above the filter plate, after the rinse cycle. (Th...

14 !8 FINAL CHECKLIST TO BE COMPLETED BY THE INSTALLER Complete and keep for safe reference: Model Serial No. Purchase Date Purchaser Dealer Address Installer’s Name Installer’s Signature Installation Company Installation Date Check all parts are installed. Ensure that all panels and parts thereof a...

5 9 1 3 8 4 C 0 5 .1 9 I N S TA L L AT I O N G U I D E N Z A U G B I E S G DD60SDF models S I N G L E D I S H D R AW E R ™ D I S H WA S H E R

8 2 1 3 !0 - A SECURE TO THE CABINETRY ON THE SIDES Open the drawer halfway.Using a flat bladed screwdriver, prise the grey rubber plug out of the trim moulding. Replace the grey rubber plug back into the trim moulding and ensure the trim seal is facing forward. Repeat for all four brackets. Using a...

10 1 2 1 2 3 4 100 mm !1 - B REFIT THE DRAWER ONTO THE RUNNERS !0 - B SECURE TO THE CABINETRY ON THE SIDES Before refitting the drawer, ensure the hoses are not twisted and the latches at the rear of each drawer runner are facing forward. Lift or rotate anti-clockwise the drawer back onto the drawer...

13 !5 TROUBLESHOOTING O Excessive water remaining above the filter plate, after the rinse cycle. (This is displayed as an A3 fault. See user guide ‘How to attend to a fault’) Check for a kinked drain hose, blocked or incorrectly drilled out waste connection, highloop not properly installed, drain ho...