Page 2 - TABLE OF CONTENTS; Introduction
TABLE OF CONTENTS Introduction 3 Warranty 3 Machine Specifications 4 Safety Labels & Symbols 6 Intended Use Of This Power Tool 6 Prohibited Use Of This Power Tool 6 Safety Precautions 6 Electrical Safety 6 Outdoor Use 7 General Power Tool Safety Instructions 7 Specific Safety Instructions 8 Blad...
Page 6 - SAFETY LABELS & SYMBOLS; Symbol; Hz; FOR ALL DOUBLE-INSULATED TOOLS; INTENDED USE OF THIS POWER TOOL; WHEN FITTED WITH A CORRECT BLADE THIS; PROHIBITED USE OF THIS
(1.8) SAFETY LABELS & SYMBOLS WARNING: Do not operate this machine if warning and/or instruction labels are missing or damaged. Contact Evolution Power Tools for replacement labels. Note: All or some of the following symbols may appear in the manual or on the product. Symbol Description V Volts ...
Page 8 - MITRE SAW SPECIFIC SAFETY
as dust masks, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries. c) Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and or battery pack, picking up or carrying the tool. Carr...
Page 10 - Do not
BLADE SAFETY WARNING: Rotating saw blades are extremely dangerous and can cause serious injury and amputation. Always keep fingers and hands at least 150mm (6”) away from the blade at all times. Never attempt to retrieve sawn material until the cutting head is in the raised position, the guard is fu...
Page 11 - PERFORM CUTS; READ
Where it is necessary to use spacer or reducing rings these must be suitable for the intended purpose and only as recommended by the manufacturer. If the mitre saw is fitted with a laser it shall not be replaced with a different type. If the laser fails to operate it shall be repaired or replaced by...
Page 13 - ADDITIONAL ACCESSORIES; Description; TCT Blade
SERIAL NO. / BATCH CODE The serial number can be found on the motor housing of the machine. For instructions on how to identify the batch code, please contact the Evolution Power Tools helpline or go to: www.evolutionpowertools.com. (4.3) ADDITIONAL ACCESSORIES In addition to the standard items supp...
Page 14 - ITEMS SUPPLIED; These items can be found in the box.
4.2) ITEMS SUPPLIED These items can be found in the box. 053-0001 053-0002 053-0003053-0004 053-0001A 053-0002A 053-0003A 053-0011 053-0004A Machine Table Extensions x2 6mm & 4mm Dual Ended Hex Key Rotary Table And Neck Cutting Head Carriage Slides Mitre Locking Knob Mains Cable Guide/Clamp Self...
Page 15 - MACHINE OVERVIEW
1. CUTTING HANDLE 2. LASER GUIDE ON / OFF SWITCH 3. REAR CARRY HANDLE* 4. TRENCH STOP 5. QUICK RELEASE HOLD DOWN CLAMP* 6. SLIDING FENCE 7. HEX KEY STORAGE 8. MACHINE TABLE EXTENSIONS 9. FRONT CLAMP HOLES 10. MOUNTING HOLE (X4) 11. BLADE GUARD LOCKING TRIGGER † 12. BLADE ROTATION INDICATION ARROW 13...
Page 18 - CLICK
18 www.evolutionpowertools.com Fig. 13 Fig. 16 Fig. 18 Fig. 19 Fig. 14a Fig. 14b CLICK Fig. 15c Fig. 15b Fig. 15a Fig. 21 Fig. 17 Fig. 20
Page 24 - ASSEMBLY AND PREPARATION; WARNING: Always disconnect the saw; TOOLS NEEDED; WARNING: Do not under any circumstances; KNOW THE PARTS
(7.1) ASSEMBLY AND PREPARATION WARNING: Always disconnect the saw from the power source before making any adjustments. Some minor assembly is required to commission this machine. By assembling this machine the owner/ operator will gain valuable insight into its many advanced features. This should en...
Page 30 - LASER SAFETY
30 www.evolutionpowertools.com ON/OFF switch for the Laser Guide is positioned on the left side of the cutting handle. (Fig. 44) Avoid direct eye contact with the laser beam, and do not use on material that could reflect the laser beam. WARNING: Do not stare directly at the laser beam. A hazard may ...
Page 31 - LASER ADJUSTMENT; WARNING: At no time during this procedure; LASER RADIATION AVOID DIRECT EYE CONTACT; PERMANENTLY MOUNTING THE
31 www.evolutionpowertools.com LASER ADJUSTMENT WARNING: At no time during this procedure should the motor be started. To check laser alignment: • Set mitre table to 0˚. • Place a piece of cardboard, or similar, onto the rotary table of the machine. • With the carriage slide in the rearmost position...
Page 32 - THE HOLD DOWN CLAMP; Using a Standard Hold Down Clamp (Included; To use the Quick Release Mechanism:
32 www.evolutionpowertools.com THE HOLD DOWN CLAMP (Fig. 49) Note: The specific type of Hold Down Clamp supplied will depend upon the model and/or type of Mitre Saw purchased. Two sockets (one either side) are incorporated into the rear of the machines Fence. These sockets provide alternative positi...
Page 35 - To tilt the cutting head:; CROWN MOULDING CUTTING
35 www.evolutionpowertools.com section of the sliding fence to provide clearance for the moving cutting head. (Fig. 42-43) The Cutting Head can be tilted from the normal 0˚ (perpendicular position) to a maximum angle of 45˚ from the perpendicular to the right hand or left hand side. Bevel cutting is...
Page 37 - TENSIONING THE DRIVE BELT; WARNING: Under no circumstances should; REPLACING THE DRIVE BELT
37 www.evolutionpowertools.com the brushes replaced by a qualified technician. TENSIONING THE DRIVE BELT WARNING: Only attempt these procedures with the machine disconnected from the power supply. Note: Belt maintenance is not necessary if the tool is used properly, however adjustments can be made i...
Page 38 - Assembly
38 www.evolutionpowertools.com ASSEMBLY SAFETY CHECKS PART CONDITION YES Slide Carriage Inserted through the bevel neck and connected to the cutting head. Locating pins successfully deployed. Mitre Handle Locking Knob Installed into mitre handle / rotary table.Slide Carriage locking screw Inserted i...
Page 39 - EC DECLARATION OF CONFORMITY
39 www.evolutionpowertools.com The manufacturer of the product covered by this Declaration is: Evolution Power Tools, Venture One, Longacre Close, Holbrook Industrial Estate, Sheffield, S20 3FR. The manufacturer hereby declares that the machine as detailed in this declaration fulfils all the relevan...
Page 40 - Notes
Page 42 - USA
V2 - BK1 EPT QR CODE USA Evolution Power Tools LLC8363 Research DriveDavenport, IA52806 T: 1-833-MULTI SAW (TOLL FREE) FR Evolution Power Tools SAS61 Avenue Lafontaine33560, Carbon-BlancBordeaux T: +33 (0)5 57 30 61 89 UK Evolution Power Tools LtdVenture One, Longacre CloseHolbrook Industrial Estate...
