EverFocus EPTZ2700i - Manuals

EverFocus EPTZ2700i – Manual in PDF format online.

Manuals:

Manual

Manual EverFocus EPTZ2700i

Summary

Page 2 - Table of Contents

2 Table of Contents 1. EPTZ2700/EPTZ2700I OVERVIEW ........................................................ 5 1.1. Introduction ................................................................................................ 5 1.2. Specifications ........................................................

Page 10 - names are marked on the board in white text.

10 1.3.2. EPTZ2700/EPTZ2700I Base Board The base board that is inside the top housing connects to power cable, video cable, control cable, alarm cable and fan. In order to connect to cables, the board needs to be taken off, and put back after finishing connecting to all cables. The connectors of cab...

Page 11 - Function

11 Pin # Function 1 ALM_NO_B (Alarm Output Normal Open B) 2 ALM_COM_B (Alarm Output Common B) 3 ALM_NC_B (Alarm Output Normal Close B) 4 ALM_NO_A (Alarm Output Normal Open A) 5 ALM_COM_A (Alarm Output Common A) 6 ALM_NC_A (Alarm Output Normal Close A) 7 ALMIN1 (Alarm Input 1) 8 GND (Ground) 9 ALMIN2...

Page 12 - Connect a video cable from EPTZ2700/EPTZ2700I to a monitor.

12 1.4. EPTZ2700/EPTZ2700I Quick Operation Guide (Work with EKB500) EPTZ2700/EPTZ2700I and EKB500 (Keyboard) can work together by using factory default setting. You just need to connect cables by the following steps: 1. Connect the RS-485 cable to EPTZ2700/EPTZ2700I and a keyboard (EKB500). 2. Conne...

Page 14 - Power Cable; extension power line may be needed.; Video Cable; amplifier may be needed if the video cable is too long.

14 2.2. Cable Needed Power Cable An adapter with 24VAC/3.5A output provides the power to the EPTZ2700/EPTZ2700I. An extension power line may be needed. Note: The input AC voltage range of an adapter depends on different area. Please make sure the voltage range before installing. Video Cable A BNC ca...

Page 19 - bits are used to set communication protocol. The factory default; Please make sure the power is off before setting, and restart the

19 2.3.2. Communication Protocol Setting The 1 st , 2 nd and 3 rd bits are used to set communication protocol. The factory default protocol is EVF. Notice: Please make sure the power is off before setting, and restart the EPTZ2700/EPTZ2700I to enable a new value after changing. Set all of protocol s...

Page 20 - Bracket and Speed Dome Installation; or other similar conditions.

20 2.4. Bracket and Speed Dome Installation 2.4.1. Installation Requirements 1. Installation should be handled by a qualified service agent and should comply with all local regulations. Service personnel should expect potential problems such as surface strength, surface material, falling objects, ou...

Page 26 - Hook

26 a. Locate the hook first. b. Clasp the rope to the hook firmly. Hook

Page 28 - release it, press orange buttons at both sides of the body.

28 11. Hold and push the main body toward the bracket until it is firmly fixed to the bracket. To release it, press orange buttons at both sides of the body. 12. Twist the cover of main body to top housing clockwise until it is firmly fixed to top housing.

Page 36 - NIGHT

36 AUTO: this mode computed the white balance value output using color information from the entire screen. It outputs the proper value using the color temperature radiating from a black subject based on a range of values. INDOOR: Camera’s white balance is fixed to indoor 3200 K. OUTDOOR: Camera’s wh...

Page 40 - SPEED; Select the dwell time (in second) for the preset position from 1 to 99.

40 SPEED : Select the speed for the preset position. The value is from 1 to 255 and 255 is the highest speed. DWELL TIME (S): Select the dwell time (in second) for the preset position from 1 to 99. FOCUS MODE: Select focus mode for the preset position from MANUAL, ONE PUSH and AUTO. WHITE BALANCE: S...

Page 42 - setting and go to next step or press IRIS- to cancel.

42 In zone menu, you can set a zone and name it, when the speed dome turns to the zone you set, it will display zone name on the screen (only if “OSD/AREAS->Display -> Zone” is set as “YES”). Turn the joystick to Up/Down to select the character. Turn the joystick Left or Right to select the ch...

Page 43 - Move the joystick to North position.

43 Turn joystick Right/Left to highlight the zone you have set and turn the joystick Up/Down to select another zone number. If you wish to clear the zone you have set, go to “CLR” and press Enter key. 3.4.3. DIRECTIONS Press Enter key of keyboard or turn joystick Left/Right to enter DIRECTIONS sub-m...

Page 51 - PLAY; or; SET; and press Enter key of keyboard.

51 3.5.3. PATTERN Press Enter key of keyboard to enter PATTERN sub-menu (see diagram 3.21) ( diagram 3.21) a. Turn the joystick Up or Down to select pattern number. b. Turn the joystick Left or Right to select action mode, either PLAY or SET . c. Select SET and press Enter key of keyboard. (diagram ...

Page 52 - . Press Enter key of keyboard. The camera starts to run the pattern

52 e. When you return to PATTERN SETUP menu, turn the joystick Left/Right to PLAY . Press Enter key of keyboard. The camera starts to run the pattern tour you set. The camera keeps playing the pattern until you press IRIS- to cancel playing and it will return to PATTERN SETUP menu. (diagram 3.23) f....

Page 53 - Exit from the current menu.

53 3.5.6. POWER UP FUNC Turn the joystick Left or Right to select the mode to return to when power failure occurs. It is selectable from PREV MODE, POS.1 (H), TOUR1, PAT.1, AUTOPAN and OFF 3.5.7. AUTO FLIP Select ON to enable Auto Flip function or select OFF to disable Auto Flip. 3.5.8. EXIT Exit fr...

Page 61 - Two point auto pan

61 4. EPTZ2700/2700I FUNCTION SETUP AND OPERATION 4.1. Manual Control Mode ¾ Manual control: Shift Joystick Up/Down/Left/Right, and turn it Clockwise/Counterclockwise to control speed dome. Use the control keys which are Zoom, Focus and IRIS function keys on the keyboard to Zoom In/Out, focus N (nea...

Page 62 - Focus on a preset position:; Press the number key, and then press Position to

62 4.3. Position Setting ¾ Focus on a preset position: Press the number key, and then press Position to focus on the number of preset position; or you can press Position, then enter the preset position number, and then press Enter to focus on the number of preset position. ¾ Preset a position: Shift...

Page 65 - Delete an alarm link:; Press; Clr; to delete a link of alarm to position/tour.

65 a frame scan. ¾ Delete an alarm link: Press Clr + F1 to delete a link of alarm to position/tour. Note 1: After alarm output signal is terminated, the speed dome will resume action or return to its original position. Note 2: After powering on the speed dome, it will detect alarm status automatical...

Page 66 - EverFocus Electronics Corp.; China Beijing

66 P/N: MW01G02300 EverFocus Electronics Corp. Head Office: 12F, No.79 Sec. 1 Shin-Tai Wu Road, Hsi-Chih, Taipei, Taiwan TEL: +886-2-26982334 FAX: +886-2-26982380 www.everfocus.com.tw USA L.A. Office: 1801 Highland Ave. Unit A Duarte, CA 91010, U.S.A. TEL: +1-626-844-8888 FAX: +1-626-844-8838 www.ev...