Page 2 - DANGER; IMPORTANT SAFETY; WARNINGS; a) Do not store a spare LP cylinder under or near this appliance.; WARNING
1 WE WANT YOU TO ASSEMBLE AND USE YOUR GRILL AS SAFELY AS POSSIBLE. THE PURPOSE OF THIS SAFETY ALERT SYMBOL IS TO ATTRACT YOUR ATTENTION TO POSSIBLE HAZARDS AS YOU ASSEMBLE AND USE YOUR GRILL. WHEN YOU SEE THE SAFETY ALERT SYMBOL PAY CLOSE ATTENTION TO THE INFORMATION WHICH FOLLOWS! READ ALL SAFETY ...
Page 3 - CALIFORNIA PROPOSITION 65 WARNING
2 General Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 LP Gas Cylinder (Tank) Specifi cations and Installation . . . . . . . . . . . . . . . . 4-6 Hose & Regulator Specifi cations and Installation . . . . . . . . . . . . . . . . . . . . 6-7...
Page 6 - • Always; LP gas cylinder (not supplied with this grill)
5 • Allow only qualifi ed licensed LP gas dealers to properly fi ll or repair your LP gas cylinder. • New tanks should be purged prior to fi lling; inform LP gas dealer if you are using a new tank. • DO NOT allow the cylinder to be fi lled beyond 80% capacity. Over-fi lled tanks can create a dangero...
Page 7 - HOSE & REGULATOR SPECIFICATIONS AND INSTALLATION:; Ensure the tank valve is
Tank Retention Screw 6 INSTALLING THE LP GAS CYLINDER (TANK) ONTO THE GRILL: 1. Check that the cylinder valve is closed by turning the knob clockwise. Inspect cylinder valve rubber seal for cracks or deterioration. Do not use propane tank with damaged seal as a gas leak may occur. 2. Place the cylin...
Page 8 - CONNECTING HOSE AND REGULATOR:; REGULATOR RESETTING PROCEDURE:
7 HOSE AND REGULATOR: Your grill is equipped with a Type 1 connection device with the following features:1. The system will not allow gas fl ow from the cylinder until a positive connection to the valve has been made. Note: The cylinder valve and all grill burner knobs must be turned OFF before any ...
Page 9 - Never perform a leak test with a match or open fl ame.; WHEN TO PERFORM A LEAK TEST:; Use caution and common sense when testing for leaks.
To prevent fi re or explosion hazard: • DO NOT smoke or permit ignition sources in the area while conducting a leak test. • Perform test OUTDOORS in a well ventilated area that is protected from the wind. • Never perform a leak test with a match or open fl ame. • Never perform a leak test while the ...
Page 10 - LIGHTING THE MAIN BURNERS:; GAS LIGHTING INSTRUCTIONS:; Follow the instructions exactly.
9 LIGHTING THE MAIN BURNERS: 1. Open lid before lighting burner. 2. Make sure all control knobs are in the “OFF” position. 3. Select burner to be lit. Push and hold down the control knob and turn SLOWLY (2 to 3 seconds) to “HIGH”. You should hear the igniter click. Note: Step 3 may need to be repeat...
Page 12 - BREAKING IN YOUR GRILL:
11 • Read and follow all warnings and instructions contained in the preceding sections of this manual. • Flavoring chips must be contained in a metal smoking box to contain ash and prevent fi res. • DO NOT cover cooking grates or other components with aluminum foil, as this blocks ventilation and da...
Page 13 - TURNING OFF THE GRILL:; USING OTHER FEATURES OF THE GRILL:; In Canada: the Canadian Electrical Code – CSA C22.1
12 TURNING OFF THE GRILL: 1. Turn off the cylinder valve. 2. Turn all burner control knobs to the “OFF” position. Note: Turn off LP cylinder fi rst to prevent gas from being left in the system under pressure. CAUTION: • The cylinder valve should always be in the off,or closed, position when the gril...
Page 14 - CLEANING INTERIOR OF GRILL:; INTERIOR OF GRILL LID:
13 WARNING: If a bristle brush is used to clean any of the cooking surfaces, ensure no loose bristles remain on the cooking surfaces prior to grilling as loose bristles may attach to food. CLEANING INTERIOR OF GRILL: • We recommend cleaning off food residue immediately after cooking by gently scrubb...
Page 15 - PROPER VALVE TO BURNER ALIGNMENT
14 BURNER ASSEMBLY/MAINTENANCE: • Although your burners are constructed of stainless steel, they may corrode as a result of the extreme heat and acids from cooking foods. Regularly inspect the burners for cracks, abnormal holes, and other signs of corrosion damage. If found, replace the burner. • DO...
Page 16 - BEFORE STORING YOUR GRILL:; Never move a grill when hot or in use.; TRANSPORTING AND STORAGE:
15 BEFORE STORING YOUR GRILL: • Ensure that the cylinder valve is fully closed. • Clean all surfaces. Lightly coat the burners with cooking oil to prevent excess rusting. • If storing the grill indoors, disconnect the LP tank and leave the LP tank OUTDOORS. • Place dust cap on cylinder valve outlet ...
Page 18 - GRILLING TO PROPER TEMPERATURE:
17 Problem Possible Cause Prevention/Cure Flame blows out High or gusting winds Do not use grill in high winds Low on LP gas Replace or refi ll LP gas tank Burner holes may be obstructed Refer to “Burner Assembly/Maintenance” instructions Flow limiting device tripped Refer to “Regulator Resetting Pr...
Page 19 - ASSEMBLY INSTRUCTIONS:; READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY; • Phillips
18 ASSEMBLY INSTRUCTIONS: READ ALL SAFETY WARNINGS & ASSEMBLY INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING OR OPERATING YOUR GRILL. WE RECOMMEND TWO PEOPLE WORK TOGETHER WHEN AS SEM BLING THIS UNIT. The following tools are required to assemble this Even Embers 4 Burner Gas Grill: • Phillips Screwdri...
Page 21 - Attach cart back panel
20 1 2 Screws and door inserts are pre-attached in door handles 18 . Remove screws and door inserts to attach door handles to door kit 12 . Remove two screws from rear legs and set aside. Attach left side cart panel 13 and right side cart panel 14 to door kit over keyholes. Tighten four screws. 3 At...
Page 22 - Attach cart base; Attach four casters
21 4 5 6 Remove two screws from cart base 16 . Remove two screws Attach cart base 16 to door kit and left and right side cart panels using two pre-attached screws on door kit and two screws removed from Step 2. Tighten all screws on cart base and back panel. Attach four casters 21 .
Page 24 - Place grill body
23 11 10b Place grill body 1 on cart. Loosen screws and rotate brackets upward. Tighten screws. 10a Remove two protective plates from right and left side of grill body assembly 1 .
Page 25 - and; LEFT
24 12 Remove two screws and washers and set aside. 13 Loosen four screws. Attach front panels 4 and 5 Make sure panels are aligned. Tighten screws. Remove screw and washer Remove screw and washer Align edges LEFT SIDE TABLE Loosen 4 screws 14 Remove one screw. Loosen four screws. Attach side table o...
Page 26 - Align Panels; RIGHT
25 16 Install screw removed from Step 12. Tighten screw 15 Install screw removed from Step 14. Align Panels Tighten screw RIGHT SIDE TABLE Loosen 4 screws Remove screw 17 Remove one screw. Loosen four screws. Attach burner table over keyholes. Make sure front panels are aligned. Tighten screws.
Page 28 - Install side burner grate
27 22 Burner Venturi Wire Clip Burner Valve Wire Clip Burner Valve Burner Venturi Attach wire clip to burner venturi. Install side burner grate 11 . Attach electrode. 21
Page 30 - Even Embers GAS1466AS Assembled
Page 31 - WARRANTY
OM1466AS1020 Owner’s Manual for Model Manual del Propietario para el Modelo GAS1466AS ©2020 The Boltz Group LLC. Carrollton, Texas 75006 U.S.A. www.evenembers.com The Boltz Group warrants to the original pur chas er that the Even Embers 4 Burner Gas Grill is free from defects due to workmanship or m...
