Ericsson F221m - Manuals

F221m The F221m is the best quality solution for providingaccess to fixed services either when no traditionalfixed infrastructure is available or if an additionalphone line is required.With the F221m terminal, the user does not have towait for the fixed telephone network infrastructure tobe develope...

External connectors and light indicators SIM card Your network operator provides you with a SIM(Subscriber Identity Module) card. The SIM cardcontains information about your telephone numberand the services included in your subscription, amongother things. Warning!: the FCT has to be switched off be...

Connections Warning!: please, before you start any connectionsrefer to section “Safe and Efficient Use” on page 49in this guide and contact your network operator ifyou have any questions. Warning!: to get a good FCT protection againstelectrical discharges and the best audio quality, agood grounding ...

The FCT is also equipped with an RS232 port thatenables you to use it as a GSM modem for PC fax,data and SMS services. For this specificconfiguration, please refer to the FCT DataReference Manual. See Accessories on page 39. Preparing your FCT You need to follow these steps before you install theFCT...

Connect a telephone to the FCT Connect a fixed telephone to the FCT telephone line. Important: you will use this telephone to dial the PIN. Switch on the FCT Connect the power supply. The FCT switches onautomatically and the green and red light indicatorsstart flashing. Enter PIN Most SIM cards are ...

Network search After you have switched on your FCT and entered thePIN, the FCT automatically searches for a network. Note: if the red light is off, there is a problem withthe power supply. See “Troubleshooting and FCTindicators” on page 33. When a network is found, the green light switches on or fla...

• Do not install the FCT on walls or rooms that contain large amounts of metal, steel or wiring. • Do not expose the FCT to extreme temperatures (near radiators, cooling vents, etc). If you experience poor reception quality, an outdoorantenna may result in improvement. See Accessories on page 39. Wa...

Warning!: once you have fixed the FCT to the walland switched it on, check the final status of the redand green lights. If either one is off, there is aproblem with the power supply or the GSM signal.See “Troubleshooting and FCT indicators” on page 33. Now the FCT is ready for connecting devices and...

Note: it is strongly recommended that the telephonewire is installed indoors in order to avoid lightningdamage. Note: the telephone wire should not exceed 600meters. Larger distances can be achieved by usinghigh quality telephone wire. Checking connections Once the fixed line devices (1 up to 3) hav...

Using telephones Fixed telephones connected to the FCT telephone linework in the same way as if they were connected to afixed network. Warning!: you will not be able to make or receivedata or fax calls while a speech call is ongoing. Note: you can also benefit from some FCTfunctionality that you do ...

Using CLI displays Devices that display the incoming number (telephoneswith display, external displays, etc.) can be directlyconnected to the FCT line interface in the same way asan ordinary telephone. If your subscription includesthe Calling Line Identification (CLI) service and thecaller´s network...

Using fax machines The FCT terminal allows the connection of Group 3analog faxes to the FCT telephone line, in the sameway as a telephone.Warning!: the fax communication service has to beregistered with your network operator. Otherwise,the network will not allow faxes to be sent or received.Warning!...

Using PCs Analog modems connected to the FCT telephone linework in the same way as if they were connected tothe fixed line. In this way, you can use your PCstandard modem to make data calls (Internetbrowsing, e-mail, etc.) through the FCT line.To be able to send and receive data calls, you need:– a ...

optionally, to improve the Internet connection, a DNSaddress and a Proxy address. All these settings willallow you to configure the Dial-up Networkingprogram in your PC in order to establish a GPRSconnection. Note: this procedure is similar to the way youconfigure an Internet connection from a speci...

Advanced features If a DTMF telephone is connected to the FCT, thefollowing features can be accessed. Changing volume During a call, you can increase or decrease thereception volume level. • Increase volume: dial R# # # # • Decrease volume: dial R**** Diverting calls (call forward) You can divert in...

Restricting calls (call barring) You can restrict certain types of calls that can bemade or received. You need a password to turn a callrestriction on or off. Initially, this password will be0000. We recommend you to change it by dialing: **03**OLD_PASSWORD*NEW_PASSWORD*NEW_PASSWORD# The following t...

• To ignore the waiting call, take no action.• To continue with the ongoing call and reject the waiting call (give a User Busy indication tone to thewaiting call): press R0. • To end the ongoing call and answer the waiting call: press R1. Note: if you hang up the telephone, you will also endthe ongo...

Voice mail The answering service of your network allows callersto leave a voice message when you cannot answeryour calls. If you have voice mail, you will hear 3 beeps beforethe dial tone, as soon as you pick up the receiver tomake a call. Note: if you have the DA20 display adapteraccessory (See “Ac...

To manage alternate line Dial … You will hear… service function … Activate Line 1 **591# 1 beep Activate Line 2 **592# 1 beep Check status Line 1 *#591# 1 beep if activated3 beeps if deactivated Check status Line 2 *#592# 1 beep if activated3 beeps if deactivated Note: if instead of hearing beeps yo...

To unblock your SIM card while changing your PIN In order to unblock your SIM card and change thePIN at the same time, please dial the followingsequence: **05*PUK*NEW_PIN*NEW_PIN# 32 Advanced features

Troubleshooting and FCT indicators This chapter describes the procedures to identify and,if possible, correct problems that might occur withthe FCT or its installation. Some problems requirethat you call your network operator, but mostproblems you encounter you can easily correctyourself. Light indi...

Audible tones The FCT generates audible tones in your telephone set, thus providing the same service characteristics as theone given by the traditional fixed network. The following table describes the nature of the main tones you will get when using the unit. Other standard callprogress tones, such ...

FCT technical data GSM AIR INTERFACE Frequency Bands: Triple-Band E-GSM 900, GSM1800 and GSM 1900 E-GSM 900Frequencies: TX 880-915 MHz, RX 925-960 MHzRF power: Maximum 2 W (33 dBm), Power class 4 GSM1800Frequencies: TX 1710-1785 MHz, RX 1805-1880 MHz RF power: Maximum 1 W (30 dBm), Power class 1 GSM...

RS232 INTERFACE • Data services: all applicable GSM 7.07 AT commands • SMS: all applicable GSM 7.05 AT commands ANTENNA (included) • Frequency Bands: Triple-Band E-GSM 900, GSM 1800 and GSM 1900 • Characteristics: omnidirectional POWER SUPPLY (included) • AC Input: 100 - 240 Vac; 47 - 63 Hz 3 pole A...

Accessories The F200 series terminals benefit from a wide rangeof accessories, which ensure the best and easiest wayto install, serve and maintain the terminals, enhancingtheir functionality. Only these approved-by-Ericsson accessories willguarantee the quality and performance of theterminals. DA20 ...

AA batteries holder (size: 99.01 mm x 51.69 mm) is provided. NiMH or NiCd rechargeable AA batteries can alsobe used with these accessory, but these batteriesmust be charged using an external charger. Warning!: Ericsson recommends precaution whenhandling lead-acid batteries, and also specialattention...

Annex: PC data configurations Windows 98 GPRS set-up Warning!: your PC must have the Dial-upNetworking and the TCP/IP protocol installedwithin the network components. You can check thisin ‘Start->Settings->Control Panel’ and doubleclicking on ‘Network’. If not, these componentshave to be previ...

4) Click on ‘Finish’. 5) In the ‘Dial-Up Networking’ folder, right-click on the created connection and select ‘Properties’. 6) In the ‘General’ tab, turn off ‘Use area code and Dialing Properties’. 7) In the ‘Server Types’ tab: – ‘Type of Dial-Up Server’: select ‘PPP: Internet, Windows NT, Windows 9...

8) Push the ‘TCP/IP Settings…’ button. – ‘Server assigned IP address’ must be checked. – ‘Server assigned name server addresses’ must be set if the network operator requires it. If thenetwork operator provides DNS addresses, thenthese must be added once ‘Specify name serveraddresses’ is marked. (Exa...

You have now installed the GPRS connection. Toconnect to the GPRS network, follow steps 1 to 3: 1) Go to ‘My Computer’-> Dial-Up Networking’ and open the previously configured connection. 2) Type the user name and password provided by your network operator and verify that thetelephone number is *...

Safe and efficient use Note: please read this information before using yourFCT. Save this user guide since it contains important safetyinformation and operating instructions. Product care • Do not expose your FCT to liquid or moisture. • Do not expose your FCT to extreme high or low temperatures. • ...

Radio frequency energy Your FCT is a radio transmitter and receiver. Whenthe FCT is turned on, it receives and transmits radiofrequency (RF) energy. The system that handles yourcall when you are using your FCT controls the powerlevel at which your FCT transmits. All Ericsson terminals are designed t...

• Do not expose the battery to extreme temperatures, never above +60°C. For maximum battery capacity,use the battery in room temperature. • Do not let the metal contacts on the battery touch another metal object. This could short-circuit anddamage the battery. • Do not expose the battery to open fla...

Limited warranty Limited warranty conditions Thank you for purchasing this Ericsson Product. Toget the maximum use out of your new product, werecommend that you follow a few simple steps: • Read the Guidelines for safe and efficient use. • Read all of the terms and conditions of the Ericsson Warrant...

Regulatory information Declaration of Conformity We, Ericsson Radio Systems AB ofKistagången 26, KistaS-16480 Stockholm, Sweden declare under our sole responsibility that our product Ericsson type 0130101-BV and in combination with our accessories, to whichthis declaration relates is in conformity w...

Definitions The following definitions are supplied in order to betterunderstand certain concepts included in this manual: Switch-on: power up the FCT by connecting the ACpower supply or a charged battery. Switch-off: power down the FCT by disconnectingthe AC power supply or removing the battery. Fix...