Equator EZ 5500 CV BL/BK - Manuals

3 Installation 1. Non-removal of shipping bolts, causing vibration / internal damage.2. Non-adjustment of feet to level machine, causing vibration / internal damage.3. Non-removal of exhaust vent plate at the back while using Venting Dry mode, causing excess heat and resulting in damage to internal ...

4 Note: All rights reserved. Designs, Specifications and Manual subject to change without notice. Inlet and Drain Hose length Power cable length 6 Feet 6 Feet 23.6 / 60 33.5 / 85 24 / 61 41.3 / 105 3

5 To reduce the risk of fire due to contaminated loads, the final part of a tumble dryer cycle occurs without heat (cool down period). Avoid stopping a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated. 16. Your Combo W...

6 The unit must be installed on a strong leveled surface in a protected, dry and well-ventilated area, with a power and water supply of sufficient capacity and a sufficient outlet in close proximity. MODEL No: SERIAL No: By using High Efficiency (HE) detergent, Front Loading detergents 19 lbs. 1400 ...

7 Venting Fan and Cover Drain Hose U-Connector Power Cord Shipping Bolts Drum Top Panel Control Panel Detergent Dispenser Drawer Door Leveling Feet Pump Filter Door ReleaseLever Drain Tube Tube Cap Cold Water Inlet Valve Hot Water Inlet Valve Blanking Cap s - 3 (To cover shipping bolts hole) Vent Ad...

b o l t s b o l t s b o l t s NOTE Save the bolt assemblies for future use. To prevent damage to internal components, DO NOT transportthe washer-dryer combo without reinstalling the shipping bolts.Failure to remove shipping bolts and retainers may cause severe vibration and noise, which can lead to ...

12 VENTLESS (CONDENSING) DRY VENTED (HOT AIR) DRY 1. ENSURE METAL VENT COVER (1) IS INSTALLED OVER EXHAUST FAN AS SHOWN IN FIG.82. Power on the machine3. Press "Dry Only" button to set the machine on drying cycle.4. Hold Vented/Ventless button for 5 seconds5. symbol will appear on the screen...

Ring plate Guide plate Latch plate 1. Unscrew the adapter ring plate and the 4 adapter retaining screws. 2. Remove the guide plate if the tap is too large to fit the adapter. 3. Push the adapter onto the end of the tap so that the rubber seal forms a watertight connection. Tighten the adapter ring p...

14 BUILT-IN, RECESSED, CLOSET AND ALCOVE INSTALLATION MINIMUM CLEARANCE OTHER THAN ALCOVE OR CLOSET INSTALATION 2" 2" 3" 3" 3" 3" Maximum Length of Exhaust Duct is 10 feet Minimum clearances to combustible surfaces: 2" (5 cm) clearance both sides and 3" (7.5 cm) rear....

15 2. DRY CYCLES Refresh Dry - 12 mins cycle blowing hot air onto the clothes before folding. Time Dry 60 - 60 mins dry cycle. 3. OTHER CYCLES: Rinse/Spin - 12 mins Spin cycle at 1000 RPM. Winterize - 2 minute cycle to winterize your appliance. (follow procedure on page 18) o Self-Clean - 9 mins cyc...

16 For small items such as socks, children’s garments and small towels please use a Washing Net Bag . Use Front Load detergent, . as per direction If you are using Wash Only cycle, you can fill the drum.If you are using Wash + Dry cycle, please do not load clothes more than 2/3 full. You can add fab...

17 Vented /Ventlessselectionbutton mode mode Vented dry mode. The default is Normal and you can select Extra, Low or Damp Dry. Press this button to select the dry level for a Sensor Dry cycle. Dry only and Dry level buttons for 5 seccods Vented Ventless Ventless mode. Ventless dry mode P o w e r Pre...

level options 18 A. How to run WASH + DRY Cycle 1. Press POWER button 2. Press START Default cycle is NORMAL - If required you can change to desired washing cycle based on type of clothes by rotating the Program Dial knob. 1. Press POWER button 2. Press WASH Only button 3. Press START 1. Press POWER...

19 Understanding the door lock function How to stop the wash cycle How to stop the dry cycle - The wash program can be stopped at any time.- Press START/PAUSE for 5 seconds- Press POWER button for 3 seconds to turn off the machine Breakage of the door handle is not How to turn on the display in ener...

20 2 1 Fig.16 Fig.15 Fig.14 Fig.13 (Fig.14) (Fig.15) (Fig.16) (Fig.13) Fig.17 (Fig.17) (Fig.18, Fig.19) Fig.18 Fig.19 is - If Vent Dry mode is used, clean the exhaust fan and exhaust duct at least once a year to prevent lint build-up.

23 enough Is the dryer button correctly pressed for the drying cycle?Is drying cycle selected (Time Dry/Sensor Dry)? Condensation at soap dispenser Slight condensation can occur at soap dispenser and will evaporate. This is normal. Front Load detergent 4" Power Front loading bolts Not drying PED...

24 DIAGNOSTIC MENU Door open Drain failure Water inlet failure Water overfill Motor failure Washing heater failure Dryer Malfunction Dryer Malfunction Water level failure Dryer Malfunction Dryer Malfunction Dryer Malfunction Communication betweendisplay & electronic module Door Switch Drain Pump ...