Enviro CE2005 - Manuals - manualsarea.com

Page 2 - Table of Contents

2 Introduction........................................................................................3 Important Safety Data...............................................................3 Water Specifications..................................................................4 Pellet Quality...........

Page 3 - Introduction; CAUTION: DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.; any warranties stated in this manual.; THE USE OF CORDWOOD IS PROHIBITED BY LAW.; assumes no responsibility for any consequential damage.

3 Introduction I MPORTANT S AFETY D ATA : Please read this entire manual before installation and use of this pellet fuel burning room heater. Failure to follow these instructions could result in property damage, bodily injury or even death. CAUTION: DO NOT CONNECT TO ANY AIR DISTRIBUTION DUCT OR SYS...

Page 4 - PELLET QUALITY IS IMPORTANT, PLEASE READ THE FOLLOWING PAGE.; liability caused by the quality of wood pellets used.

4 P ELLET Q UALITY : PELLET QUALITY IS IMPORTANT, PLEASE READ THE FOLLOWING PAGE. Your pellet stove has been designed to burn wood pellets only. Since there are many manufacturers of wood pellets, it is important to select pellets that are free of dirt or any impurities. Ask your dealer for a recomm...

Page 5 - such liquids well away from the pellet stove while it is in use.; In the event of a malfunction; , turn the water heater feed OFF. Push the ON/OFF button; manufacturer. Use only Enviro approved replacement parts

5 W ARNINGS AND R ECOMMENDATIONS : A. Do not abuse the glass by striking or slamming the door shut.B. Do not attempt to operate the stove with broken glass.C. Do not attempt to open the door and clean the glass while the unit is in operation. To clean the glass, use a soft cotton cloth and mild wind...

Page 6 - The rating label is located on the hopper lid.

6 Introduction R ATING L ABEL L OCATION : The rating label is located on the hopper lid. A PPLIANCE D IMENSIONS : 37 3 / 8 " (94.9cm) 25 7 / 16 " (64.6cm) 25 1 / 4 " (64.1cm) � �� ...

Page 7 - Operating Instructions; CONVECTION BLOWER CONTROL

T URNING P ELLET S TOVE O N : Ensure the hopper has sufficient pellet fuel to start the unit. 1. Set water temperature, using the rotary dial located above the feed controls. 2. Press the ON / OFF button to start the appliance. System light will flash, auger light will flash with the pulse of the au...

Page 8 - OFF

8 This is used to regulate the airflow through the pellet stove.• On the low heat output settings, push the slider all the way in.• On the high heat output pull the slider out or until a good fire is achieved. A good fire is in between a fire with lazy black tipped flames and a forced fire (very qui...

Page 9 - Routine Cleaning and Maintenance

9 Routine Cleaning and Maintenance The following list of components should be inspected and maintained routinely to ensure that the appliance is operating at its’ optimum and giving you excellent heat value: CAUTION WHEN VACUUMING FLY ASH: BECAUSE THE FLY ASH IS VERY FINE, THE USE OF A FINE FILTER V...

Page 10 - quality. Refer to “Warnings and Recommendations”; DO NOT PLACE UNBURNED OR RAW PELLET FUEL IN

10 DOOR GLASS Do not attempt to open the door and clean the glass while the unit is in operation or if glass is hot. To clean the glass, use a soft cotton cloth and mild window cleaner, gas or wood stove glass cleaner, or take a damp paper towel and dip into the fly ash. This is a very mild abrasive...

Page 11 - HEAT EXCHANGER AND INTERNAL EXHAUST TUBES:

11 Routine Cleaning and Maintenance � � HEAT EXCHANGER AND INTERNAL EXHAUST TUBES: ONLY TO BE CLEANED WHEN THE UNIT IS COLD. Clean away any fly ash that may have collected in and on the tubes. As different types of pellets produce different amounts of ash, cleaning of the tubes should be done on a r...

Page 12 - technicians or installers.; The convection blower will not function normally.; Troubleshooting

*NOTE: All troubleshooting procedures should be carried out by qualified technicians or installers. DO NOT: • Hold the ON / OFF BUTTON; this is a momentary contact switch and can be damaged if held down too long. • Service the stove with wet hands. The stove is an electrical appliance, which may pos...

Page 13 - The #2 light is flashing on the heat level indicator light; To reset Circuit Board after a trouble code - push the ON/OFF button.

Troubleshooting 5. The stove will not shut off. « If the unit will not shut off, ensure that the thermostat (if equipped) is turned down below the room temperature (thermostat mode in the ON / OFF position). « If the unit is in the HI/LOW mode the unit will not shut off but will go to an idle settin...

Page 14 - Warranty; ON AN OFFICIAL WARRANTY CLAIM FORM:

14 Warranty Sherwood Industries Ltd. gives a five year limited warranty on all steel manufactured parts. A one-year warranty is provided on all electrical components. The above limited warranties are extended only to the original purchaser. There is no warranty on the following parts: ● Glass window...

Page 15 - Installation Data Sheet

The following information must be recorded by the installer for warranty purposes and future reference. NAME OF OWNER: _________________________________________ ADDRESS: _________________________________________ _________________________________________ _________________________________________ PHON...