Enviro C-11253 - Manuals

Specifications R ATING L ABEL L OCATION : The rating label is located under the control panel and is attached to a rectangular metal sheet that is chained to the fireplace. D IMENSIONS : 5 1 11 / 16 " (44mm) 8 1 / 2 " (216mm) 13 7 / 8 " (362mm) 7 7 / 16 " (188mm) 5 7 / 16 " (138m...

WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY A FIRE OR EXPLOSION MAY RESULT, CAUSING PROPERTY DAMAGE, PERSONAL INJURY OF LOSS OF LIFE. L IGHTING AND T URNING O FF I NSTRUCTIONS : Figure 3: Lighting instruction label. 1. ARRÊTEZ! Lire les instructions de sécurité mentionnées plus haut. 2....

Operating Instructions The Sonnet is designed to gradually lower or raise the flame as is needed in application. It normally does not just turn on and off. This is very dependant on the size of the room the unit is located in. During the first several operational cycles the electronics go through a ...

TIMER MODE – (appliance must be in standby mode; pilot ignited): The Timer mode is normally programmed to have two (2) Periods: P1 and P2. Between these two (2) periods, a lower operating temperature (or pilot only) can be set. Note: that between those periods, if the thermostat is set to a certain ...

10 Operating Instructions There is one venturi adjustment. Use this venturi adjustment lever, shown in Figure 8, to achieve a proper and efficient flame. Pull the rod forward for more air or push it in for less air. Adjust lever until the flame pattern is similar to Figure 79. Figure 8: Adjusting th...

Maintenance And Service Warning: Failure to position the parts in accordance with this manual, or failure to use only parts specifically approved with this appliance, may result in property damage or personal injury.At least once a year, run through the following procedures to ensure the system is c...

Maintenance And Service G LASS D OOR R EMOVAL : C LEANING T HE P AINTED S URFACES : Painted faces should be wiped with a damp cloth periodically. R EPLACING T HE B ATTERIES : It is recommended that the batteries are replaced at the beginning of each heating season. Batteries must be changed when an ...

13 Sonnets are to be installed, confirm that the remote control signal codes are different for each unit.To change the code, complete the following:1. Change DIP switch position (shown at the top of Figure 13).2. Press and hold the receiver’s reset button (see Figure 14) until you hear two (2) acous...

Warning: This conversion kit shall be installed by a qualified service agency in accordance with the manufacturer’s instructions and all applicable codes and requirements of the authority having jurisdiction. If the information in these instructions is not followed exactly, a fire, explosion or prod...

Figure 22: Burner Removal. Figure 21: Unfastening Burner. Maintenance And Service Kit Parts List: 1 - Orifice (Natural Gas #42 DMS or Propane #54 DMS) 1 - Conversion label 1 - Installation instruction sheet Carefully inspect the orifice supplied with this conversion kit. If it has been damaged or is...

17 Initial Installation WARNING: Operation of this heater when not connected to a properly installed and maintained venting system can result in carbon monoxide (CO) poisoning and possible death. C LEARANCES TO C OMBUSTIBLES : Maintain sufficient clearances for operation, service and maintenance. • ...

Door removed for clarity 1⁄4” Tube Initial Installation QUALIFIED INSTALLERS ONLY B-V ENT M ODEL : WARNING: This appliance has been designed to operate by drawing combustion air and dilution air from the room. It is also designed to draw room air for proper heat circulation from the sides of the uni...

19 7. As you push the unit into its final position in the fireplace, if the vent collar plate was removed, reinstall it to the stove by sliding it along the draft hood and secure with the screws previously removed. 8. Using a 1⁄4” hex driver, adjust the levelling legs to ensure the unit is level and...

21 Note: To convert a B-Vent to a Direct Vent, remove the air intake plug, remove the spill switch assembly and re-install the flue slider bottom plate, re-install the jumper onto the thermocouple wire, re-install the air intake cover plates, install the proper venting, re-install the screw into the...

�� ����� �� ����� Install sealed throat connector or flashing to prevent leakage of room air up through chimney. DV Only: Before installing vent liners, mark each liner on both ends to designate which is the intake and the exhaust. Measure the height of the chimney beforehand and purchase the approp...

23 18" (457mm) 18" (457mm) Trim flashing as required. Figure 41: Vertical Vent Cap Dimensions. Initial Installation QUALIFIED INSTALLERS ONLY D IRECT V ENT V ERTICAL V ENT T ERMINATION : For use with Sonnet Direct Vent Fireplace Insert. The Vertical Vent Cap is termination, rain cap, and a t...

Initial Installation QUALIFIED INSTALLERS ONLY The height for the vent must be between 10ft (3.05m) and 35ft (10.67m). Install sealed Vertical Vent Cap to prevent leakage of room air up through chimney. The intake is 2" (51mm) and the exhaust is 3" (76mm). Measure the height of the chimney b...

Figure 47: Installing Fan onto Back Panel. Figure 46: Removing/Installing Back Panel From Sonnet. O PTIONAL F AN K IT : Tools Required: ● 1⁄4” Socket or Driver or Flat Head Screwdriver ● Utility Knife Kit Contents: Quantity Description 1 Fan Kit Assembly (includes Back Cabinet Panel, Fan, Mounting B...

27 Fan Only Replacement: 1. Unplug the power or turn off the electrical breaker for the unit. 2. Follow steps 1-4 in R EMOVING V ALVE C OVER - M AINTENANCE A ND S ERVICE . 3. The fan hangs on a grommet at either end of the mounting bracket (see Figure 47), lift the fan assembly up and off the gromme...

28 • A shut-off valve is not supplied with this unit but one should be installed.• The appliance and its shut-off valves must be disconnected from the gas supply piping system during any pressure testing where the pressure exceeds 1⁄2 psig (3.45 KPa) or the valve will be damaged. • The unit must be ...

R EMOTE H ANDSET W ALL B RACKET I NSTALLATION : Kit Contents: Quantity Description 1 Wall Bracket (Top & Bottom) 1 Spacer 1 Countersink Head Screw 2 Pan Head Screw 2 Spacer 55: Wall Bracket Installation Option 1. Figure 56: Wall Bracket Installation Option 2. Figure 57: Wall Bracket Installation...

30 Secondary Installation O PTIONAL B ASE S HELF & R ISER : The Sonnet Base Shelf (15⁄8” (41 mm) high) and Base Shelf Riser (21⁄8” (54 mm) high) are black powder coated components that can be combined to create a riser with an overall height of 2 3 / 16 ” (55 mm). This shelf can be installed wit...

B RICK P ANEL I NSTALLATION : NOTE: The brick liner is fragile and should be handled gently. 1. Ensure the Sonnet is turned off and allow the unit to cool. 2. Remove the glass door as shown in the M AINTENANCE AND S ERVICE - G LASS D OOR R EMOVAL . Warning: Do not touch or attempt to remove the glas...

35 Secondary Installation L OG S ET AND E MBER I NSTALLATION : NOTE: The logs are fragile and should be handled gently. Figure 72. Empty firebox. Figure 73. First Stage Log Set Installation. Figure 74. Second Stage Log Set Installation. Figure 73: The back left log rests behind the left ledge pointe...

Secondary Installation Figure 75. Third Stage Log Set Installation. Figure 77. Fifth Stage Log Set Installation. Figure 76. Fourth Stage Log Set Installation. Figure 75: The center of the right log fits onto the locator pin on the back right log (see Figure 74). The front of the log is to rest on th...

37 Secondary Installation Figure 79. Sonnet complete log set-up with embers burning. NOTE: While the glass is still removed, it is recommended that the gas line be purged by lighting the pilot.When lighting the fireplace for the first time since the log set and embers have been installed/replaced, w...

Trouble Shooting Problem Possible Cause Solution No transmissions; remote control doesn’t work. Receiver must learn new code. • Reset the receiver’s code, refer to M AINTENANCE A ND S ERVICE - C HANGING R EMOTE H ANDSET C ODE . One or more of the batteries are dead. • Replace the batteries, refer to...

Parts List 41 Reference Number Part Description Part Number 1 120°F (49°C) Ceramic Fan Temperature Sensor EC-001 2 FPI Burner Switch EC-026 3 Domestic Power Cord (115V) EC-042 4 Heyco Strain Relief EC-044 5 Embers (Coal & Wool) EC-046 6 Convection Blower 115V 50-1549 12 oz. Can of Flat Black Tou...

Parts Diagram - Components SONNET -Components February 20 07 � � � �� � � � � �� �� �� �� � � �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� 43

Parts Diagram - Options SONNET -Options November 20 06 �� �� �� �� �� �� �� �� �� 44

45 Warranty Sherwood Industries Ltd. is the manufacturer of the Enviro line of heating products. At Sherwood Industries, our commitment to the highest level of quality and customer service is the most important thing we do. Each Enviro stove is built on a tradition of using only the finest materials...

Warranty 4. The stove must be operated and maintained at all times in accordance with the instructions in the Owner’s Manual. If the unit shows signs of neglect or misuse, it is not covered under the terms of this Warranty policy. Performance problems due to operator error will not be covered by the...

48 Installation Data Sheet The following information must be recorded by the installer for warranty purposes and future reference. NAME OF OWNER: _________________________________________ ADDRESS: _________________________________________ _________________________________________ ___________________...