Enviro C-11148 - Manuals

5 Installation D ECIDING W HERE TO L OCATE YOUR P ELLET A PPLIANCE : 1. Check clearances to combustibles. 2. Do not obtain combustion air from an attic, garage or any unventilated space. Combustion air may be obtained from a ventilated crawlspace. 3. Do not install the stove in a bedroom. 4. You can...

7 Installation C LEARANCES TO C OMBUSTIBLES : Use a hearth pad that extends 6 inches (15 cm) in front of the unit when installing on a combustible floor. A LCOVE C LEARANCES : This unit may be installed in an alcove. Maintain these clearances to combustibles. Minimum Alcove width 48 inches (122 cm) ...

fumes such as stairwells, covered breezeway, etc. 2. Vent surfaces can become hot enough to cause burns if touched by children. Non-combustible shielding or guards may be required. 3. Termination must exhaust above the inlet elevation. It is recommended that at least five feet of vertical pipe be in...

9 Installation E XHAUST L OCATION : 8 3 / 4 " (222mm) 10 3 / 4 " (273mm) Figure 6: Bern Inlet and Outlet Location. Base of unit to center of flue 103⁄4” (273 mm) Side of unit to center of flue 83⁄4” (222 mm) [at center of unit] Figure 7: Corner Installation. C ORNER T HROUGH W ALL I NSTALLAT...

11 Installation 10. Install a vertical pipe, or if all requirements for direct venting are met, install vent termination. The stainless steel cap termination manufactured by the vent manufacturer is recommended. However, when the vent terminates several feet above ground level and there are no trees...

Installation E XTERIOR M OUNTED E XHAUST B LOWER : The Bern can be equipped with an externally mounted exhaust blower. This optional kit includes all components necessary to install the exhaust blower on any vertical wall surface. 1. Remove the left hand cabinet side by removing the two (2) screws d...

Installation T YPICAL T HROUGH W ALL W ITH E XTERIOR B LOWER K IT I NSTALLATION - H ORIZONTAL T ERMINATION : Electrical Cable Bern 90° Elbow 45°Elbow with Rodent screen or stainless steel termination hood 2ft (610mm) Riser Pipe Adaptor Exterior Blower and Housing Wall Strap To supply power to the ex...

Installation T HERMOSTAT I NSTALLATION : If the unit has been placed in the HI / LOW mode, the unit will be taken to a low or idle setting when the thermostat is not calling for heat. When the thermostat calls for heat, the unit will go to the setting that is displayed on the control board Heat Indi...

19 If the fire should happen to go out and the heat output indicator has been set on the lowest setting, the Slider Damper should be pushed in slightly, decreasing the air in the firebox.If, after long periods of burning, the fire builds up and overflows the burn pot or there is a build up of clinke...

20 Installation O PTIONAL P ANEL K IT : This kit must be installed before the unit is started. Figure 29: Screws at back of the cab side. Figure 27: Screws above door top corner. Figure 28: Screw behind ash box. Tools Required: ●T-20 screwdriver Kit Components: Quantity Description 1 Left Cab Panel ...

21 Installation 1 2 3 Figure 30: Installing Hopper Lid. Installing Hopper Lid: 1. Attach the hopper brackets to the back of the unit with a screw in each top holes of the brackets (#1 in Figure 30). Do not tighten these screws until all six (6) screws are in place. 2. Lay the hopper lid in place, sl...

Troubleshooting DO NOT: ● Service the stove with wet hands. The stove is an electrical appliance, which may pose a shock hazard if handled improperly. Only qualified technicians should deal with possible internal electrical failures. ● Do not remove from the firebox any screws without penetrating oi...

23 Troubleshooting ü Poor Quality Fuel – Insufficient energy in the fuel to produce enough heat to keep the stove burning or operational. ü Exhaust Temperature Sensor failure. – Bypass sensor located on Exhaust Blower if stove now operates properly, the unit may require cleaning or a new sensor. Con...

Troubleshooting 7. The convection blower will not function normally. ü Clean all grill openings at the back and below unit . ü Press the fan button; does the fan come on? Press again to verify that the blower turns on; if, not contact your local dealer for service. 8. Ignitor- the pellets will not l...

25 Wiring Diagram Connect Thermostat Here Red Red Red Red Brown Brown Brown Brown White White White White White 115V White 220V Blue White White Orange Orange Orange Orange Yellow Yellow Grey Grey GreyGrey Purple Purple Blue 115V Black 220V Brown Black Black Black Blue Black Black Armor Cable Suppli...

Parts List Reference Number Description Part Number 1 120°F (49°C) Ceramic Fan Temperature Sensor EC-001 2 Auger Motor - 220V EF-001-220V 3 High Limit Temp Sensor 200°F (93°C) Manual Reset EF-016 4 Vacuum Switch - 220V EF-017-220V Silicone Hose EF-018 Aluminum Hose Barb EF-019 Shoulder Bolt, Hardene...

Parts Diagram - Components Bern - Components February 2005 � �� �� � �� �� � �� �� � �� �� � �� �� � � � 28

29 Parts Diagram - Steel B er n -S te el C om po ne nt s Fe br ua ry 20 05 �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� � �� ��

Warranty Sherwood Industries Ltd. gives a five year limited warranty on all steel manufactured parts. A one-year warranty is provided on all electrical components. The above limited warranties are extended only to the original purchaser. There is no warranty on the following parts: ● Glass window ● ...

31 NAME OF OWNER: _________________________________________ ADDRESS: _________________________________________ _________________________________________ _________________________________________ PHONE:___________________________________ NAME OF DEALER: _________________________________________ ADDRE...