Enviro C-11112 - Manuals - manualsarea.com

Page 2 - Table of Contents

2 Table of Contents Introduction............................................................................................................3 Pellet Quality..................................................................................................3Automatic Safety Features.......................

Page 3 - Introduction; Pellet quality is important, please read the following:; will void the warranty.; ASH; may allow longer intervals between cleaning.; REASONS WHY THE UNIT OVERHEATED.

3 Introduction * This manual is designed for the home owner in conjunction with the technical manual. * P ELLET Q UALITY : Pellet quality is important, please read the following: Your enviro pellet stove has been designed to burn wood pellets only. Do not use any other type of fuel, as this will voi...

Page 4 - adjusting the slider damper located on the left side of the stove.; Caution: Do not connect to any air distribution duct or system.; warranty. Check with your dealer for fuel recommendations.; THE USE OF CORDWOOD IS PROHIBITED BY LAW.; slider/damper as needed to ensure proper combustion.

4 I MPORTANT S AFETY D ATA : P lease read this entire Owner’s Manual before installing or operating your ENVIRO Pellet Stove. Failure to follow these instructions may result in property damage, bodily injury or even death. Contact your local building or fire official to obtain a permit and any infor...

Page 5 - have thoroughly cooled before disposing of them.; ELECTRICAL: The use of a surge protected power bar is recommended.; The unit must be; Never; the heater while it is in use.; KEEP ASH PAN FREE OF RAW FUEL.; SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE

ASHES: Disposed ashes should be placed in a metal container with a tight-fitting lid. The closed container of ashes should be on a non-combustible floor on the ground, well away from all combustible materials pending final disposal. The ashes should be retained in the closed container until all cind...

Page 6 - Specifications; The rating label is located on the back of the hopper.

6 Specifications D IMENSIONS : Figure 1: Empress Dimensions. 24 7 / 16 " (621mm) 27 3 / 8 " (695mm) 24 3 / 16 " (614mm) 15 3 / 8 " (390mm) 25 3 / 4 " (653mm) 15 3 / 4 " (400mm) R ATING L ABEL L OCATION : The rating label is located on the back of the hopper.

Page 7 - Operating Instructions; THE SLIDER / DAMPER MUST BE SET AT TIME OF INSTALLATION.

The easiest way to make sure that an efficient flame is achieved is to understand the characteristics of the fire. • A tall, lazy flame with dark orange tips requires more air – Open slider (pull out) slightly. • A short, brisk flame, like a blowtorch, has too much air – Close slider (push in) sligh...

Page 8 - This light will flash in conjunction with the auger.; HEAT OUTPUT INDICATOR:

Operating Instructions C ONTROL B OARD F UNCTIONS : 1. AUGER TRIM: Used to change feed rates on LOW ONLY for poorer quality fuels. Push the Auger Trim button until the number 1 and 5 lights appear on the Heat Level Indicator. This will increase the feed rate to four (4) seconds ON time per Auger pul...

Page 9 - PRE-BURN INSTRUCTIONS; low setting is too hot for the room (see “; OPERATION – ON / OFF mode; when the thermostat contacts close again.; DO NOT unplug unit while Combustion fan is operating.

9 Operating Instructions O PERATING Y OUR P ELLET S TOVE : PRE-BURN INSTRUCTIONS : The burn pot liner holes must be clear and the liner installed correctly against the ignitor tube for proper operation. Check the hopper for enough pellets to start the unit. DO NOT OPERATE THE UNIT WITH THE DOOR OR A...

Page 10 - TOOLS REQUIRED TO CLEAN UNIT; • Torx T-20 Screwdriver • Brush; BURN POT AND LINER; Routine Cleaning and Maintenance; Failure

2-3 Days / Weekly Semi-annually or 2 Tons of Fuel Burn Pot and Liner Exhaust Vent Ash Pan Fresh air Intake Tube Inside Firebox Blower Mechanisms Door Glass Heat exchanger tubes Heat exchanger tubes Behind firebox liners Ash pan and Door gaskets All Hinges Door Latch Post Season Clean-up TOOLS REQUIR...

Page 12 - EXHAUST VENT; Check all the hinges on the unit to ensure proper movement.; CLEANING SURFACES; All surfaces should be brushed off periodically.

Routine Cleaning and Maintenance EXHAUST VENT (season) This vent should be cleaned every year or after two (2) tons of pellets. We recommend contacting your dealer for professional cleaning. To clean the vent pipe, tap lightly on the pipe to dislodge any loose ash. Open the bottom of the “T” to dump...

Page 13 - Warranty

13 Warranty Sherwood Industries Ltd. gives a five year limited warranty on all steel manufactured parts. A one-year warranty is provided on all electrical components. The above limited warranties are extended only to the original purchaser.There is no warranty on the following parts: ● Glass window ...

Page 14 - Installation Data Sheet

MANUFACTURED BY: SHERWOOD INDUSTRIES LTD. 6782 OLDFIELD RD. SAANICHTON, BC, CANADA V8M 2A3 www.envirofire.biz May 15, 2006 C-11112 NAME OF OWNER: _________________________________________ ADDRESS: _________________________________________ _________________________________________ ___________________...