Enviro C-10629 - Manuals - manualsarea.com

Page 2 - Table of Contents

Table of Contents 2 Introduction..............................................................................................................3 Pellet Quality..................................................................................................3 Automatic Safety Features of Your Pellet S...

Page 3 - Introduction; will void the warranty.

3 Introduction * This manual is designed for the home owner in conjunction with the technical manual. * P ELLET Q UALITY : Pellet quality is important, please read the following: Your enviro pellet stove has been designed to burn wood pellets only. Do not use any other type of fuel, as this will voi...

Page 4 - adjusting the slider damper located on the left side of the stove.; Caution: Do not connect to any air distribution duct or system.; warranty. Check with your dealer for fuel recommendations.; THE USE OF CORDWOOD IS PROHIBITED BY LAW.; damper as needed to ensure proper combustion.

4 I MPORTANT S AFETY D ATA : P lease read this entire Owner’s Manual before installing or operating your ENVIRO Pellet Stove. Failure to follow these instructions may result in property damage, bodily injury or even death. Contact your local building or fire official to obtain a permit and any infor...

Page 5 - have thoroughly cooled before disposing of them.; ELECTRICAL: The use of a surge protected power bar is recommended.; The unit must be; Never; the heater while it is in use.; KEEP ASH PAN FREE OF RAW FUEL.; SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE

5 Introduction ASHES: Disposed ashes should be placed in a metal container with a tight-fitting lid. The closed container of ashes should be on a non-combustible floor on the ground, well away from all combustible materials pending final disposal. The ashes should be retained in the closed container...

Page 6 - The rating label is located on the inside of the ash pan cover.

15 1 / 2 " (393 mm) 18 7 / 8 " (481 mm) 17 1 / 2 " (444 mm) 19 5 / 8 " (497 mm) 17 7 / 8 " (455 mm) 33 7 / 8 " (861 mm) 6 Introduction R ATING L ABEL L OCATION : The rating label is located on the inside of the ash pan cover. A PPLIANCE D IMENSIONS : Figure 1: Dimensions of B...

Page 7 - Operating Instructions

7 Operating Instructions C ONTROL B OARD F UNCTIONS : 1. AUGER TRIM: Used to change feed rates on LOW ONLY for poorer quality fuels. Push the Auger Trim button until the number 1 and 5 lights appear on the Heat Level Indicator. This will increase the feed rate to 2.5 seconds ON time Auger pulse. Thi...

Page 8 - PRE-BURN INSTRUCTIONS; low setting is too hot for the room (see “; OPERATION – ON / OFF mode; when the thermostat contacts close again.; DO NOT unplug unit while Combustion fan is operating.

8 Operating Instructions O PERATING Y OUR P ELLET S TOVE : PRE-BURN INSTRUCTIONS : The burn pot liner holes must be clear and the liner installed properly against the ignitor tube for proper operation. Check the hopper for enough pellets to start the unit. DO NOT OPERATE THE UNIT WITH THE DOOR OR AS...

Page 10 - Routine Cleaning and Maintenance; BURNER POT AND LINER; TOOLS REQUIRED TO CLEAN UNIT:; Vacuum with fine filter bag

10 2-3 Days / Weekly Semi-annually or 2 Tons of Fuel Burn Pot and Liner Exhaust Vent Heat Exchanger Tubes Air Intake Ash Pan Blower Mechanisms Door Glass Heat Exchanger Tubes Inside Firebox Behind Firebox Liners & Covers Ash Pan and Door Gaskets All Hinges Door Latch Post Season Clean-up Routine...

Page 11 - EXHAUST PASSAGES; ASH PAN; DO

EXHAUST PASSAGES (semi-annually) To prevent build up of fly-ash all the exhaust passages must be cleaned and vacuumed. Routine Cleaning and Maintenance If the glass has build up that can not be removed with only the cloth, clean the glass using paper towel and a gas appliance glass cleaner, this may...

Page 12 - EXHAUST VENT

Routine Cleaning and Maintenance Removal of the firebox backing. • Open the door by lifting the handle, remove the burn pot and burn pot liner. • Lubricate all screws with penetrating oil. • Remove the four (4) screws that hold the side panels in place. • With the tip of a flat screwdriver, gently l...

Page 13 - Warranty; ON AN OFFICIAL WARRANTY CLAIM FORM:

13 Warranty Sherwood Industries Ltd. gives a five year limited warranty on all steel manufactured parts. A one-year warranty is provided on all electrical components. The above limited warranties are extended only to the original purchaser. There is no warranty on the following parts: ● Glass window...

Page 14 - Installation Data Sheet

14 The following information must be recorded by the installer for warranty purposes and future reference. NAME OF OWNER: _________________________________________ ADDRESS: _________________________________________ _________________________________________ _________________________________________ P...