Enviro 50-830 - Manuals - manualsarea.com

Page 2 - Table of Contents

2 Introduction..............................................................................................................3 Pellet Quality..................................................................................................3Automatic Safety Features.......................................

Page 3 - Introduction; Pellet quality is important, please read the following:; will void the warranty.; ASH; may allow longer intervals between cleaning.; REASONS WHY THE UNIT OVERHEATED.

3 Introduction * This manual is designed for the home owner in conjunction with the technical manual. * P ELLET Q UALITY : Pellet quality is important, please read the following: Your enviro pellet stove has been designed to burn wood pellets only. Do not use any other type of fuel, as this will voi...

Page 4 - adjusting the slider damper located on the left side of the stove.; Caution: Do not connect to any air distribution duct or system.; warranty. Check with your dealer for fuel recommendations.; THE USE OF CORDWOOD IS PROHIBITED BY LAW.; slider/damper as needed to ensure proper combustion.

4 I MPORTANT S AFETY D ATA : P lease read this entire Owner’s Manual before installing or operating your ENVIRO Pellet Stove. Failure to follow these instructions may result in property damage, bodily injury or even death. Contact your local building or fire official to obtain a permit and any infor...

Page 5 - SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE

5 ASHES: Disposed ashes should be placed in a metal container with a tight-fitting lid. The closed container of ashes should be on a non-combustible floor on the ground, well away from all combustible materials pending final disposal. The ashes should be retained in the closed container until all ci...

Page 7 - Operating Instructions; CONVECTION BLOWER CONTROL:

7 Operating Instructions C ONTROL B OARD F UNCTIONS : 1. AUGER TRIM: Used to change feed rates on LOW ONLY for poorer quality fuels. Push the Auger Trim button until the number 1 and 5 lights appear on the Heat Level Indicator. This will increase the feed rate to four (4) seconds ON time Auger pulse...

Page 8 - PRE-BURN INSTRUCTIONS; low setting is too hot for the room (see “; OPERATION – ON / OFF mode; when the thermostat contacts close again.; DO NOT unplug unit while Combustion fan is operating.

8 Operating Instructions O PERATING Y OUR P ELLET S TOVE : PRE-BURN INSTRUCTIONS : The burn pot liner holes must be clear and the liner installed correctly against the ignitor tube for proper operation. Check the hopper for enough pellets to start the unit. DO NOT OPERATE THE UNIT WITH THE DOOR OR A...

Page 9 - THE SLIDER / DAMPER MUST BE SET AT TIME OF INSTALLATION.

9 Operating Instructions S LIDER / D AMPER S ETTING : THE SLIDER / DAMPER MUST BE SET AT TIME OF INSTALLATION. A Qualified Service Technician or Installer must set the Slider Damper . The combustion exhaust blower is a variable speed blower controlled by the heat output button. This blower will decr...

Page 10 - TOOLS REQUIRED TO CLEAN UNIT; • Torx T-20 Screwdriver • Brush; BURN POT AND LINER; Routine Cleaning and Maintenance; Failure

2-3 Days / Weekly Semi-annually or 2 Tons of Fuel Burn Pot and Liner Exhaust Vent Ash Pan Fresh air Intake Tube Inside Firebox Blower Mechanisms Door Glass Heat exchanger tubes Heat exchanger tubes Behind firebox liners Ash pan and Door gaskets All Hinges Door Latch Post Season Clean-up TOOLS REQUIR...

Page 12 - CLEANING PLATED SURFACES

12 EXHAUST PASSAGES (season) Removal of the firebox backing for bi- annual cleaning (refer to Figure 8): • Open the door by lifting the handle, remove the burn pot and burn pot liner. • Lubricate all screws with penetrating oil. • Remove the four (4) screws that hold the brick liner retainers in pla...

Page 13 - Warranty

13 Warranty Sherwood Industries Ltd. gives a five year limited warranty on all steel manufactured parts. A one-year warranty is provided on all electrical components. The above limited warranties are extended only to the original purchaser.There is no warranty on the following parts: ● Glass window ...

Page 14 - Installation Data Sheet

14 The following information must be recorded by the installer for warranty purposes and future reference. NAME OF OWNER: _________________________________________ ADDRESS: _________________________________________ _________________________________________ _________________________________________ P...