Enviro 50-1578 - Manuals

Enviro 50-1578 – Manual in PDF format online.

Manuals:

Manual

Manual Enviro 50-1578

Summary

Page 2 - Table of Contents

2 Table of Contents Safety Warnings & Recommendations.........................................................................3 Installation...............................................................................................................6 Rating Label Location.........................

Page 3 - Safety Warnings & Recommendations

3 Safety Warnings & Recommendations * This manual is designed for the technician in conjunction with the owner’s manual. * Please read this entire Owner’s Manual before installing or operating your ENVIRO Pellet Stove. Failure to follow these instructions may result in property damage, bodily in...

Page 4 - ELECTRICAL: The use of a surge protected power bar is recommended.

4 Safety Warnings & Recommendations CLEANING: There will be some build up of fly ash and small amounts of creosote in the exhaust. This will vary due to the ash content of the fuel used and the operation of the stove. It is advisable to inspect and clean the exhaust vent semi-annually or every t...

Page 5 - in “Air Tight Homes” or where required by local codes.; SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE

5 Safety Warnings & Recommendations FRESH AIR: Outside Fresh Air connection is optional. Fresh Air must be connected to all units installed in “Air Tight Homes” or where required by local codes. Consider all large air moving devices when installing your unit and provide room air accordingly. NOT...

Page 6 - Installation

Installation R ATING L ABEL L OCATION : The rating label is located on the back of the hopper. D ECIDING W HERE TO L OCATE YOUR P ELLET A PPLIANCE : 1. Check clearances to combustibles (see I NSTALLATION - C LEARANCES TO C OMBUSTIBLES and I NSTALLATION - A LCOVE C LEARANCES ). 2. Do not obtain combu...

Page 9 - NOTE: Venting terminals shall not be recessed into walls or siding.

9 hot enough to cause burns if touched by children. Non-combustible shielding or guards may be required. 3. Termination must exhaust above the inlet elevation. It is recommended that at least five feet of vertical pipe be installed outside when the appliance is vented directly through a wall, to cre...

Page 11 - size and clearance to combustibles.; temperature silicone.

11 Figure 8: Corner Installation. 100mm (4") 100mm (4") Fresh Air Intake Wall thimble manufactured by pellet vent manufacturer. Installation C ORNER T HROUGH W ALL I NSTALLATION : H ORIZONTAL E XHAUST T HROUGH W ALL I NSTALLATION : Vent installation: install vent at clearances specified by t...

Page 18 - TO SUPPLY POWER TO THE EXHAUST BLOWER:; the exterior vent housing.

TO SUPPLY POWER TO THE EXHAUST BLOWER: Install an amour coated electrical cable from the exhaust blower housing, through the wall thimble, and attach to the pre-drilled hole in the left hand rear hopper pillar. Hook up to wires from the wiring harness for the exhaust blower. All electrical connectio...

Page 19 - Refer to

19 Storm Collar Roof Flashing Roof Rafters Roof Sheathing Ceiling Joist Vertical Vent Pipe Outside Vent Termination Exterior Wall Sheathing Rain cap - ensure cap is at least 900mm (3 ft) above the roof at the lowest point Installation T HROUGH W ALL V ERTICAL I NSTALLATION W ITH E XHAUST B LOWER : R...

Page 20 - THE AIRFLOW THROUGH THE PELLET STOVE.; fuels may require higher

S LIDER /D AMPER S ETTING : THE SLIDER / DAMPER MUST BE SET AT TIME OF INSTALLATION, IT IS USED TO REGULATE THE AIRFLOW THROUGH THE PELLET STOVE. A Qualified Service Technician or Installer must set the Slider Damper . If the unit has been placed in the HI / LOW mode, the unit will be taken to a low...

Page 22 - Troubleshooting; flash

Troubleshooting DO NOT: ● Service the stove with wet hands. The stove is an electrical appliance, which may pose a shock hazard if handled improperly. Only qualified technicians should deal with possible internal electrical failures. ● Do not remove from the firebox any screws without penetrating oi...

Page 23 - The exhaust motor will not function normally.; replace; To reset Circuit Board after a trouble code - push the ON/OFF button

23 Troubleshooting ü Check vacuum levels in the exhaust channel by bypassing the vacuum switch, then remove the vacuum hose from vacuum switch. Check exhaust vacuum readings by placing the open end of the vacuum hose on a Magnahelic Gauge (readings must be above 0.18” to 0.20” W.C. (44.8 to 49.8 Pa)...

Page 24 - The convection blower will not function normally.

Troubleshooting ü If the auger gear box does not turn but the motor’s armature does try to spin then the auger is jammed. – Try to break apart jam by poking at the jam through the drop tube. If this fails then empty the hopper and remove the auger cover **remember to re-seal the cover after installa...

Page 25 - Wiring Diagram

25 Wiring Diagram Connect Thermostat Here Red Red Red Red Brown Brown Brown Brown White White White White White White Orange Orange Orange Orange Yellow Yellow Grey Grey Purple Purple Blue Black Black Black Blue Black Armor Cable Supplied Vacuum Switch Combustion Blower Optional Exterior Exhaust Blo...

Page 26 - Parts List - Components

Reference Number Description Part Number 1 120 °F (49 °C) Ceramic Fan Temperature Sensor EC-001 2 Auger Motor - 220V EF-001-220V 3 High Limit Temp Sensor 200 °F (93 °C) Manual Reset EF-016 Silicone Hose EF-018 External Exhaust Back EF5-143 External Exhaust Box EF5-144 External Exhaust Bottom EF5-145...

Page 27 - Gloves

27 Reference Number Description Part Number Auger Motor Mount 50-687 Auger Plate with bushing 50-688 Auger Mounting Hardware 50-689 22 IEC Power Cord Inlet Socket 50-713 Hinge Pin - Silver 50-750 Oval Ceramic Gasket 50-766 23 Circuit Board 5 Amp Fuses - 220V (Pair) 50-834 24 Exhaust Starter Tube 80m...

Page 29 - ay; Parts Diagram - Components

W IN D SO R -C om po ne nt s M ay 20 07 �� Parts Diagram - Components 29

Page 31 - Installation Data Sheet

31 NAME OF OWNER: _________________________________________ ADDRESS: _________________________________________ _________________________________________ _________________________________________ PHONE:___________________________________ NAME OF DEALER: _________________________________________ ADDRE...