Enterasys Networks C1H124-48 - Manuals

DECLARATION OF CONFORMITY Application of Council Directive(s): 89/336/EEC73/23/EEC Manufacturer’s Name: Enterasys Networks, Inc. Manufacturer’s Address: 50 Minuteman Road Andover, MA 01810USA European Representative Address: Enterasys Networks Ltd.Nexus House, Newbury Business ParkLondon Road, Newbu...

Contents ix Contents Figures ............................................................................................................................................xiTables..............................................................................................................................

x Contents 3.3 Installing Optional Mini-GBICs ........................................................................ 3-2 3.4 Installing the Device ........................................................................................ 3-53.4.1 Rackmount Installation..................................

Figures xi Figure Page Figures 1-1 C1H124-48 Standalone Device ....................................................................................... 1-2 1-2 C1G124-24 Standalone Device....................................................................................... 1-3 3-1 Mini-GBIC with MT-...

xii Tables Table Page Tables 3-1 Contents of Shipping Carton .........................................................................................3-2 4-1 LANVIEW LEDs ............................................................................................................4-2 4-2 Troubleshooti...

About This Guide xiii About This Guide This guide provides information necessary to install and set up the Matrix C1 Series C1H124-48 and C1G124-24 devices and available options. For information about the Command Line Interface (CLI) set of commands used to configure and and manage the C1H124-48 and...

Structure of This Guide xiv About This Guide STRUCTURE OF THIS GUIDE This guide is organized as follows: This preface provides preliminary information to help you use this guide and a brief summary of each chapter, defines conventions used in this document, and lists technology and user guides that ...

How to Use This Guide About This Guide xv HOW TO USE THIS GUIDE RELATED DOCUMENTS The following documents can help you to set up and manage the C1H124-48 and C1G124-24: Matrix C Series Redundant Power System Installation Guide Matrix C Series Configuration Guide Cabling Guide The manuals listed abov...

Document Conventions xvi About This Guide DOCUMENT CONVENTIONS This guide uses the following conventions: NOTE: Calls the reader’s attention to any item of information that may be of special importance. TIP: Conveys helpful hints concerning procedures or actions. CAUTION: Contains information essent...

Introduction 1-1 1 Introduction This chapter introduces the C1H124-48 and C1G124-24 standalone Ethernet switch devices. 1.1 OVERVIEW The following provides an overview of the C1H124-48 and C1G124-24. C1H124-48 The C1H124-48 ( Figure 1-1 ) has several types of port connections, which include • forty-...

C1G124-24 1-2 Introduction Figure 1-1 C1H124-48 Standalone Device C1G124-24 The C1G124-24 ( Figure 1-2 ) has several types of port connections, which include • twenty-four front panel RJ45 ports (10BASE-T/100BASE-TX/1000BASE-T compliant), and • four expansion slots for optional Mini-GBIC interface m...

C1H124-48 and C1G124-24 Introduction 1-3 Figure 1-2 C1G124-24 Standalone Device C1H124-48 and C1G124-24 The switch functions can be configured using the WebView™ application, CLI switching commands, or SNMP. Each device can be installed as a tabletop unit or installed into a standard 19-inch rack us...

Port Trunking 1-4 Introduction 1.3 PORT TRUNKING Port Trunking is used for load balancing or load sharing. Port Trunking provides a mechanism to group, or aggregate, multiple links of any technology together to scale the backbone bandwidth beyond the limitations of a single link. All links are user-...

802.1p Port Priority Introduction 1-5 1.7 802.1p PORT PRIORITY The 802.1p port priority is used to assign a default priority to the frames received without priority information in their tag header, map prioritized frames to the appropriate transmit queues, and prioritize frames according to protocol...

UPN Support 1-6 Introduction 1.11 UPN SUPPORT User Personalized Networks (UPN) is an architecture that allows network administrators to map network services to identified users, machines, peripherals and other network entities. UPN consists of three tiers: • Classification rules make up the first or...

100BASE-TX Twisted-Pair Network 2-2 Network Requirements 2.2 100BASE-TX TWISTED-PAIR NETWORK When connecting a 100BASE-TX segment to one of the fixed ports (1 through 48), or to an optional Ethernet expansion module, use Category 5 UTP cabling. The device at the other end of the twisted pair segment...

Hardware Installation 3-1 3 Hardware Installation This chapter provides the instructions required to install the device. Follow the order of the sections as listed below to correctly install the device. • Unpacking the device ( Section 3.2 ) • Installing options ( Section 3.3 ) • Installing the devi...

Unpacking the Device 3-2 Hardware Installation 3.2 UNPACKING THE DEVICE Unpack the device as follows: 1. Open the box and remove the packing material protecting the device. 2. Verify the contents of the carton as listed in Table 3-1 . 3. Remove the tape seal on the non-conductive bag to remove the d...

Installing Optional Mini-GBICs Hardware Installation 3-3 To prepare and install a Mini-GBIC, proceed as follows: Preparation Before installing the Mini-GBIC, proceed as follows: 1. Attach the antistatic wrist strap (refer to the instructions in the antistatic wrist strap package) before removing the...

Installing Optional Mini-GBICs 3-4 Hardware Installation Figure 3-2 Mini-GBIC with LC Connector (C1H124-48 shown) Removing the Mini-GBIC To remove a Mini-GBIC from the C1H124-48 port slot, proceed as follows: 1. Attach the antistatic wrist strap (refer to the instructions in the antistatic wrist str...

Installing the Device Hardware Installation 3-5 4. Grasp the sides of the Mini-GBIC and pull it straight out of the port slot . If storing or shipping the Mini-GBIC, insert the dust protector into the Mini-GBIC to protect the fiber ports. 3.4 INSTALLING THE DEVICE For a tabletop or shelf installatio...

Installing the Device 3-6 Hardware Installation 3.4.1 Rackmount Installation To install the device in a 19-inch rack, you need: • Two rackmount brackets and mounting screws (rackmount kit) shipped with the device. • Four user-supplied screws to attach the device to a standard 19-inch rack. 3.4.1.1 G...

Installing the Device Hardware Installation 3-7 2. With the mounting brackets attached, position the device between the vertical frame members of the 19-inch rack as shown in Figure 3-5 . Then fasten the device securely to the frame using four mounting screws (user supplied). Figure 3-5 Fastening th...

Connecting to the Network 3-8 Hardware Installation Figure 3-6 Device, Rear View 3. Observe that the power (RPS) LED (not shown), located on the front panel, turns ON (green) and the CPU turns red until the device completes its initialization. It takes under 30 seconds for the device to boot up. 4. ...

Connecting to the Network Hardware Installation 3-9 3.5.1 Connecting UTP Cables The RJ45 fixed front panel ports (1 through 48) of the C1H124-48 are 10BASE-T/100BASE-TX compliant and have internal crossovers. The RJ45 fixed front panel ports (1 through 24) of the C1G124-24 are 10BASE-T/100BASE-TX/10...

Connecting to the Network 3-10 Hardware Installation 3. Verify that a link exists by checking that the Link/Activity LED is ON (solid green or blinking green). If the Link/Activity LED is OFF, perform the following steps until it is on: a. Verify that the cabling being used is Category 5 or better w...

Connecting to the Network 3-12 Hardware Installation Figure 3-11 Eight-Wire Straight-Through Cable RJ45 Pinouts for 10/100/1000BASE-T 3.5.2 Connecting Fiber-Optic Cables to MT-RJ Ports This section contains the procedures for connecting a 1000BASE-SX multimode fiber-optic segment from the network or...

Connecting to the Network Hardware Installation 3-13 To connect an MT-RJ cable to a fixed MT-RJ connector of a Mini-GBIC, refer to Figure 3-12 and proceed as follows: 1. Remove the protective covers (not shown) from the front panel MT-RJ fiber-optic port (port 52 in this example) and from the connec...

Connecting to the Network 3-14 Hardware Installation 3. Plug the other end of the cable into the appropriate port on the other device. Some cables may be terminated at the other end with two separate connectors, one for each fiber-optic strand. In this case, ensure that the transmit fiber-optic stra...

Connecting to the Network Hardware Installation 3-15 Enterasys Networks recommends labeling fiber-optic cables to indicate receive and transmit ends. Many cables are pre-labeled, providing matching labels or tapes at both ends of each strand of cable. To connect an LC cable connector to a fixed LC c...

Connecting to the Network 3-16 Hardware Installation Figure 3-13 Cable Connection to LC Multimode Fiber-Optic Connectors 3. Plug the other end of the cable into the appropriate port on the other device. Some cables may be terminated at the other end with two separate connectors, one for each fiber-o...

Connecting to Console Port for Local Management Hardware Installation 3-17 3.6 CONNECTING TO CONSOLE PORT FOR LOCAL MANAGEMENT This section describes how to install a UTP straight-through cable with RJ45 connectors and optional adapters to connect a PC, a VT series terminal, or a modem to an Enteras...

Connecting to Console Port for Local Management 3-18 Hardware Installation 4. Turn on the PC and configure your VT emulation package with the following parameters: When these parameters are set, the Startup screen will display. Proceed to Section 3.7 to complete the installation. Figure 3-14 Connect...

Connecting to Console Port for Local Management Hardware Installation 3-19 4. Turn on the terminal and access the Setup Directory. Set the following parameters on your terminal: When these parameters are set, the Startup screen will display. Proceed to Section 3.7 to complete the installation. Figur...

Connecting to Console Port for Local Management Hardware Installation 3-21 3.6.5 Adapter Wiring and Signal Assignments Console Port Adapter Wiring and Signal Diagram RJ45 DB9 Pin Conductor Pin Signal 1 Blue 2 Receive (RX) 4 Red 3 Transmit (TX) 5 Green 5 Ground (GRD) 2 Orange 7 Request to Send (RTS) ...

Connecting to Console Port for Local Management 3-22 Hardware Installation Modem Port Adapter Wiring and Signal Diagram RJ45 DB25 Pin Conductor Pin Signal 1 Blue 2 Transmit (TX) 2 Orange 8 Data Carrier Detect (DCD) 4 Red 3 Receive 5 Green 7 Ground (GRD) 6 Yellow 20 Data Terminal Ready (DTR) 8 Gray 2...

Completing the Installation Hardware Installation 3-23 3.7 COMPLETING THE INSTALLATION After installing the Enterasys Networks device and making the connections to the network, proceed as follows: Initial Logon to Device Management To initially access device management from your local pc, terminal, ...

Troubleshooting 4-1 4 Troubleshooting This chapter provides information concerning the following: • Using LANVIEW ( Section 4.1 ) • Troubleshooting checklist ( Section 4.2 ) • Using the Reset button ( Section 4.3 ) 4.1 USING LANVIEW The C1H124-48 (shown in Figure 4-1 ) and the C1G124-24 use the Ente...

Using LANVIEW Troubleshooting 4-3 RPS Off No power indicated by either the internal or a connected external power supply, or there is no power redundancy available from the external power supply. 1. Ensure that the power cords are plugged in correctly and that there is power at the two power sources...

Troubleshooting Checklist 4-4 Troubleshooting 4.2 TROUBLESHOOTING CHECKLIST If the device is not working properly, refer to Table 4-2 for a checklist of problems, possible causes, and recommended actions to resolve the problem. Table 4-2 Troubleshooting Checklist Problem Possible Cause Recommended A...

Troubleshooting Checklist Troubleshooting 4-5 Cannot contact the device through in-band management. IP address not assigned. Refer to the Matrix C Series Configuration Guide for the IP address assignment procedure. Port is disabled. Enable port. Refer to the Matrix C Series Configuration Guide for i...

Using the Reset Button 4-6 Troubleshooting 4.3 USING THE RESET BUTTON If you forget the password to the device management entity, you can use the Reset button shown in Figure 4-1 to reset the device management password. Figure 4-2 Reset Button To reset the device password, proceed as follows: 1. Mak...

Specifications A-1 A Specifications This appendix provides information about the following: • C1G124-24 and C1H124-48 specifications ( Section A.1 ) • Optional Mini-GBIC input/output port specifications ( Section A.2 ) • Gigabit Ethernet ( Section A.3 ) • Console Port pinout assignment ( Section A.4...

C1G124-24 and C1H124-48 Specifications A-2 Specifications A.1 C1G124-24 AND C1H124-48 SPECIFICATIONS Table A-1 provides the I/O ports, processors and memory, physical, and environmental specifications for the C1G124-24 and C1H124-48. Table A-1 Device Specifications Item Specification C1G124-24 I/O P...

C1G124-24 and C1H124-48 Specifications Specifications A-3 Redundant Power Source Connector External Power Connector on rear of the C1G124-24 and C1H124-48 15-pin D-type connector for an optional dc Power/Monitor cable connection from an external redundant power supply module (CSER-RPS-PSM). Physical...

Mini-GBIC Input/Output Specifications A-4 Specifications A.2 MINI-GBIC INPUT/OUTPUT SPECIFICATIONS The Mini-Gigabit Ethernet Card (Mini-GBIC) port expansion slots can accept 1000BASE-SX short wavelength or 1000BASE-LX long wavelength fiber-optic Mini-GBICs (refer to Table A-2 ). The optional Mini-GB...

Gigabit Ethernet Specifications Specifications A-5 A.3.2 MGBIC-LC09 Specifications (1000BASE-LX) Table A-4 MGBIC-LC01 / MGBIC-MT01 Operating Range Item Modal Bandwidth @ 850 nm Range 62.5 µm MMF 160 MHz/km 2-220 Meters 62.5 µm MMF 200 MHz/km 2-275 Meters 50 µm MMF 400 MHz/km 2-500 Meters 50 µm MMF 5...

Console Port Pinout Assignments A-6 Specifications A.4 CONSOLE PORT PINOUT ASSIGNMENTS The Console port is a serial communications port that supports local management of the C1H124-48 and C1G124-24. These pin assignments differ from other Enterasys products. Refer to Table A-7 for the Console port p...