Empire Comfort Systems CIBV-30-20 - Manuals

Page 5 15627-5-0807 Introduction Always consult your local Building Department regarding regulations, codes or ordinances which apply to the installation of a vented fireplace heater. Instructions to Installer 1. Installer must leave instruction manual with owner after installation. 2. Installer must...

15627-5-0807 Page 6 SPECIFICATIONS Model CIBV-30 Input BTU/HR (KW/H) Maximum 30,000 (8.7) BTU/HR (KW/H) Minimum 21,000 (6.2) Height 27 3/4" (704mm) Width 25 `/1" (647mm) Depth including diverter 21" (533mm) Gas Inlet 1/2" (13mm) Size Draft Diverter Collar 4" (101mm) Floor to top ...

15627-5-0807 Page 7 Consult the current National Fuel Gas Code, ANSI Z223.1 CAN/ CGA-B149 (.1 or .2) installation code. Recommended Gas Pipe Diameter Pipe Length Schedule 40 Pipe Inside Diameter Tubing, Type L Outside Diameter Nat. L.P. Nat. L.P. 0-10 feet 0-3 meters 1/2” 12.7mm 3/8” 9.5mm 1/2” 12.7...

Page 8 15627-5-0807 Clearances: When facing the front of the fireplace heater the minimum clearances to combustible construction (material) are the following:Open in front to provide service, access, and clearance to construction.Top of appliance (ceiling) 36 (inches) Draft Diverter to Rear Wall 2 (i...

Page 9 15627-5-0807 Figure 5 Assembly of Stove Casting (Figures 6, 7, 8, 9, 10, 11 and 12) Attention: Included in the hardware package are (8) 1/4" inside diameter washers. A 1/4" washer may be used with a 1/4-20 x 3/8" bolt when assembling the stove casting parts. If a bolt hole is not ...

Page 10 15627-5-0807 Figure 7 5. Align the 3/8" hole at the top of the leg with the 3/8" hole in the leg pad. Attention: For proper positioning of the leg to the leg pad the (2) 1-1/2" top edges of the leg must be placed flush and parallel to the (2) edges on the leg pad. Attach leg to le...

Page 12 15627-5-0807 x 19 3/8" heat shield with the front of the appliance. Align the (4) tabs with clearance holes on the 12" x 19 3/8" heat shield with the (4) screw holes on the heat exchanger top. Attach the 12" x 19 3/8" heat shield to the heat exchanger top with (2) 1/2"...

Page 13 15627-5-0807 WIRE CHANNEL INSTALLATION The ON/OFF/REMOTE switch with harness is factory installed into the switch box. After the appliance housing is installed into the casting the wire channel can be installed. 1. Attach switch box on the left side of rear cover with (2) 10 x 1/2" screw...

Page 15 15627-5-0807 Venting 1. Flue pipe must be as large as the flue collar on the draft diverter. 2. Maintain an upward slope of at least 1/4 inch (6mm) per foot of horizontal run. 3. Run flue pipe as directly as possible with a minimum of elbows. 4. Flue pipe should extend through the wall of a ch...

Page 16 15627-5-0807 FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. A. This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow the...

Page 18 15627-5-0807 CIBV-30 ON/OFF/REMOTE Switch CIBV-30 is equipped with an ON/OFF/REMOTE switch which is located on the wire channel. A wire harness is attached to the ON/OFF/REMOTE switch. The red, black and green (wires) female push-ons attach to the ON/OFF/REMOTE switch. At the opposite end of...

Page 19 15627-5-0807 Installation of Remote Receiver (Figure 20) 1. Attach, from left to right, the slide-on cover plate onto the remote receiver. ON will be to the top and OFF will be to the bottom on the slide-on cover plate. 2. Push the receiver slide button onto the receiver slide switch. Revers...

Page 21 15627-5-0807 With proper installation and maintenance, your new Vented Fireplace Heater should provide years of trouble-free service. If you do experience a problem, refer to Trouble Shooting Guide below. This guide will assist a qualified service person in the diagnosis of problems and the c...

Page 22 15627-5-0807 Empire Comfort Systems, Inc. Nine Eighteen Freeburg Ave. Belleville, Illinois 62222-0529 Parts can be ordered only through your service person or dealer. For best results, the service person or dealer should order parts through the distributor. Parts can be shipped directly to t...

Page 24 15627-5-0807 Index Part No. Number Description Index Part No. Number Description 1 *CI-006 WINDOW RETAINING TAB 2 R-3948 WINDOW (BLACK PAINT) 2 R-3688 WINDOW (BLACK ENAMEL) 2 R-3696 WINDOW (SAND ENAMEL) 2 R-3704 WINDOW (GREEN ENAMEL) 2 R-3712 WINDOW (RED ENAMEL) 2 R-3720 WINDOW (NAVY ENAMEL)...

Page 25 15627-5-0807 Models: CIFB-1, CIPB-1, CIPG-1, CIPS-1, CIPN-1, CIPR-1 PARTS VIEW FOR STOVE CASTING

Page 26 15627-5-0807 Installing Optional CIB-2 Blower 1. Loosen, but do not remove, (4) hex-head screws located on the exterior, bottom of the appliance. 2. Position the blower assembly at the rear of the appliance. The blower assembly has (4) keyholes for attachment to the exterior, bottom of the a...