Emerson Fisher 8532- Manuals

8532 Valve Instruction Manual Form 5288 November 2007 6 Table 3. Valve Body Data, CL150 VALVE SIZE, NPS SHAFT DIA. AT YOKE BEARING FACE-TO-FACE DIMENSION (1) MINIMUM I.D .(2) APPROXIMATE WEIGHT, KILOGRAMS mm Wafer Single-Flange 14 30.2 92.1 331.2 71.7 94.8 16 31.75 101.6 375.2 93.9 137.9 18 38.1 114...

8532 Valve Instruction Manual Form 5288November 2007 7 Figure 3. Available Seal Configurations B23133/IL GRAPHITEGASKET Adjusting the Actuator Travel Stops orTravel Key number locations are shown in figure 9, unlessotherwise noted. 1. Refer to the actuator instruction manual to locatethe actuator tr...

8532 Valve Instruction Manual Form 5288 November 2007 8 Table 5. Hex Head Screw, Stud Bolt and Cap Screw Data (1) VALVE SIZE, NPS NO. OF CAP SCREWS NO. OF STUD BOLTS SIZE-DIA. INCH & THREAD LENGTH OF CAP SCREWS, INCH LENGTH OF STUD BOLTS, INCH CL150 CL300 CL150 CL300 CL150 CL300 CL150 CL300 CL15...

8532 Valve Instruction Manual Form 5288November 2007 9 Figure 5. Proper Installation Steps B2263-1/IL CAUTION For non-ENVIRO-SEAL packing:Tighten the packing follower nuts onlyenough to prevent shaft leakage.Excessive tightening will acceleratewear of the packing and could producehigher friction loa...

8532 Valve Instruction Manual Form 5288 November 2007 10 4. Attach the bonding strap assembly (key 131,figure 6) to the shaft with the clamp (key 130, figure 6). 5. Connect the other end of the bonding strapassembly to the valve flange cap screws. 6. For more information, refer to the PackingMainten...

8532 Valve Instruction Manual Form 5288November 2007 11 Figure 7. Anti-Blowout Design Details C0758-1/IL CUTAWAY, INTERNAL DETAILS damaged shaft could cut the packingand allow leakage. 1. Before loosening any parts on the valve, releasethe pressure from the pipeline. Then, remove thehex nuts (key 15...

8532 Valve Instruction Manual Form 5288 November 2007 12 5. Install new packing one ring at a time, using thepacking follower as a driver. If using split-ringpacking, stagger the splits in the rings to avoidcreating a leak path. 6. Reinstall packing parts. Refer to figure 9 forsequence of packing pa...

8532 Valve Instruction Manual Form 5288November 2007 13 Table 6. Torque Values for Fasteners FASTENER NOMINAL SIZE RETAINING RING SCREWS GASKET RETAINING BOLTS N S m In S lbs N S m In S lbs #10 4.6 41 4.0 35 1/4 11 100 9.2 81 5/16 25 220 19 167 3/8 45 400 33 295 N S m ft S lbs N S m ft S lbs 7/16 72...

8532 Valve Instruction Manual Form 5288November 2007 15 splined end) is called the upper shaft(key 3). The shaft opposite the uppershaft is called the lower (follower)shaft (key 4). CAUTION When using an actuator, the actuatortravel stop (or actuator traveladjustment, for actuators withoutadjustable...

8532 Valve Instruction Manual Form 5288 November 2007 16 Remove the hex head bolts (key 23) andlockwashers (key 22) from the gasket retainer andremove the gasket retainer and gasket (key 21) toexpose the end of the lower shaft. 7. Before removing the lower shaft (key 4), be surethe valve disc is pro...

8532 Valve Instruction Manual Form 5288November 2007 17 body bore into the bearing bore below the packingbox. Use caution to prevent damage to the bearing. 6. Hold the upper shaft thrust bearing (key 24) in thevalve body bore against the counterbore of theupper shaft bearing bore. Push the upper sha...

8532 Valve Instruction Manual Form 5288 November 2007 18 Parts Ordering Typical parts are shown in figure 9. When corresponding with your Emerson ProcessManagement sales office about a Type 8532 valve,identify the valve as a Type 8532 and provide thevalve serial number. For valve/actuator combinatio...

8532 Valve Instruction Manual Form 5288November 2007 19 Parts List Note Part numbers are shown for recommended spares only. For part numbers not shown, contact your Emerson Process Management sales office. Key Description Part Number 1 Valve BodyIf you need a valve body as a replacement part, order ...