Emerson CP200- Manuals

Page 2 - Inlet Pressure Ratings and Flow and Sizing Coefficients; Product Description; The CP200 Series pressure loaded regulators are intended; Available Configurations; WArNiNG; could result in an explosion and/or fire causing

CP200 Series 2 Table 2. Inlet Pressure Ratings and Flow and Sizing Coefficients series OriFiCe siZe MAXiMUM OPerATiNG iNLeT PressUre (1)(2) FLOW COeFFiCieNTs (WiDe-OPeN) C 1 ieC siZiNG COeFFiCieNTs inch mm psig bar C g C v X T F D F L CP200 1/8 3/16 1/4 3/8 1/2 3.2 4.8 6.4 9.5 13 125 125 125 60 40 8...

Page 3 - Specifications; Orifice Sizes and Flow and IEC Sizing Coefficients; Outlet Pressure Ranges

CP200 Series 3 Available Configurations Type CP200iN - Regulator with internal registration Type CP200iT - Regulator with internal registration and token relief Type CP205iN - Type CP200IN with Secondary Seat™ Protection Type CP205iT - Type CP200IT with Secondary Seat Protection Type CP206iT - Type ...

Page 4 - Principle of Operation; Type CP200 Base regulator; Increasing Downstream Demand; Type CP205 with secondary seatTM Protection

CP200 Series 4 Principle of Operation Refer to Figure 2. The CP200 Series has spring-to-close construction and uses 67CP Series pressure loading regulator to supply loading pressure to the top of the main diaphragm. Since the loading pressure regulator controls the main regulator, adjustment to the ...

Page 5 - lockup. In the event that the primary orifice and disk cannot; Protection Limitations; CAUTiON; CP200 Series with Secondary Seat; Protection; CONTROL SPRING

CP200 Series 5 CLOSING SPRING DIAPHRAGM CONTROL SPRING VALVE STEM LEVER PRESSURE RETAINING PLUG (DO NOT REMOVE) MAIN REGULATOR TYPE 67CP PRESSURE LOADING REGULATOR SECONDARY SEAT™ DETAIL INLET PRESSUREOUTLET PRESSUREATMOSPHERIC PRESSURE LOADING PRESSURE Type CP206 secondary seat Protection with Blee...

Page 6 - indicates that the primary orifice/seat or the disc are no; installation and Overpressure; to permit free flow of gas to the atmosphere.; Specifications section may cause leakage,; General installation instructions; • Ensure gas flow through the regulator is in the same; installation Location; vehicular traffic and damage from other external sources.; CP200 Series Regulator Installed with a Type 289H

CP200 Series 6 Secondary Seat™ Protection does not provide additional overpressure protection in the event the secondary seat or disk is damaged by debris or contamination in the pipeline, or from conditions that would cause the regulator to go wide-open. When selecting Secondary Seat Protection opt...

Page 7 - startup; Adjustment; shutdown

CP200 Series 7 • Install the regulator with the vent pointed vertically down, see Figure 4. If the vent cannot be installed in a vertically down position, the regulator must be installed under a separate protective cover. Installing the regulator with the vent down allows condensation to drain, mini...

Page 8 - Maintenance; disassembly without first isolating the; regulator reassembly; the orifice from; Trim Maintenance

CP200 Series 8 Maintenance ! WArNiNG To avoid personal injury or equipment damage, do not attempt any maintenance or disassembly without first isolating the regulator from system pressure and relieving all internal pressure as described in “shutdown”.regulators that have been disassembled for repair...

Page 9 - Parts Ordering; The type number, orifice size, and date of manufacture are; Parts List; CP200 series Main valve and Actuator; Type 67CP Pressure Loading

CP200 Series 9 2. Inspect the removed parts for damage and debris. Replace any damaged parts. 3. To remove the valve cartridge assembly, grasp the end of the cartridge (key 10) and pull it straight out of the body (key 1). Replace with new cartridge assembly. The cartridge assembly may be disassembl...

Page 10 - CP200 Series Regulator Assembly

CP200 Series 10 Figure 5. CP200 Series Regulator Assembly APPLY LUBriCANT (L) / seALANT (s) (1) L1 = ANTi-seiZe LUBriCANT L2 = siLiCON GreAse s = ThreAD seALANT 1. LUBriCANTs/seALANT MUsT Be seLeCTeD sUCh ThAT TheY MeeT The TeMPerATUre reqUireMeNTs. 15 60 17 70 29 71 30 16 L S TORQUE: 63 TO 90 INCH-...

Page 12 - 7CP Series Pressure Loading Regulator Assembly

CP200 Series ©Emerson Process Management Regulator Technologies, Inc., 2008, 2013; All Rights Reserved industrial regulators emerson Process Management regulator Technologies, inc. USA - Headquarters McKinney, Texas 75070 USA Tel: +1 800 558 5853 Outside U.S. +1 972 548 3574 Asia-Pacifi c Shanghai 2...