Emerson 5081C-HT - Manuals - manualsarea.com

Page 2 - Instruction Sheet; Specifications; pHySICAl SpeCIFICATIoNS

2 5081C-HT Instruction Sheet January 2015 LIQ_MAN_ABR_5081C-HT/Rev.G Specifications pHySICAl SpeCIFICATIoNS Housing: Cast aluminum with epoxy coating. Type 4X (IP65). Neoprene O-ring cover seals. 160.5 mm x 175.3 mmx 161.3 mm (6.3 in. x 6.9 in. x 6.4 in.) diameter: 155.4 mm (6.1 in.) electrical Cond...

Page 3 - FIGURe 1. Infrared remote controller

INFRARed ReMoTe CoNTRolleR 1. Pressing a menu key allows the user access to calibrate, program, or diagnostic menus. 2. Press ENTER to store data and settings. Press NEXT to move from one submenu to the next. Press EXIT to leave without storing changes. 3 Instruction Sheet 5081C-HT LIQ_MAN_ABR_5081C...

Page 4 - pRoGRAM; process display

4 5081C-HT Instruction Sheet January 2015 LIQ_MAN_ABR_5081C-HT/Rev.G pRoGRAM MeNU MNeMoNICS 5000 25.0C 12.00mA CAL keyPROG keyDIAG keyHOLD key 5081C-HT Process Display Screen µ S/cm pRoGRAM FIGURe 2. Menu Tree CAlIbRATIoN dIAGNoSTICS process display Mtr CAL tE M P AbS C 0 air 5081-C-Ht CELL COnSt So...

Page 5 - FIGURe 3. AMS configuration screen using HART

5 Instruction Sheet 5081C-HT LIQ_MAN_ABR_5081C-HT/Rev.G January 2015 ASSeT MANAGeMeNT SolUTIoNS (AMS) Rosemount Analytical AMS windows provide access to all transmitter measurement and configuration variables. The user can read raw data, final data, and program settings FIGURe 3. AMS configuration s...

Page 6 - program Menu

6 5081C-HT Instruction Sheet January 2015 LIQ_MAN_ABR_5081C-HT/Rev.G VARIAble NAMe MNeMoNIC FACToRy SeTTINGS CUSToMeR SeTTINGS program Menu output Output – ___________ 4 mA 4 mA 0 µS ___________ 20 mA 20 mA 20 mS ___________ Hold hold 21 mA ___________ Fault fault 22 mA ___________ Dampening dpn 0 s...

Page 7 - Wiring; WIRING THRoUGH A jUNCTIoN boX; Recommended Transmitter Settings*; poWeR WIRING

7 Instruction Sheet 5081C-HT LIQ_MAN_ABR_5081C-HT/Rev.G January 2015 Wiring Wire sensor as shown below in Figure 5. Keep sensor wiring separate from power wiring. For best EMI/RFI pro- tection, use shielded output signal cable in an earth- grounded metal conduit. Refer to the sensor instruction manu...

Page 8 - Installation; UNpACKING ANd INSpeCTIoN

8 5081C-HT Instruction Sheet January 2015 LIQ_MAN_ABR_5081C-HT/Rev.G Installation UNpACKING ANd INSpeCTIoN Inspect the shipping container. If it is damaged, contact the shipper immediately for instructions. Save the box. If there is no apparent damage, unpack the container. Be sure all items shown o...

Page 9 - ROSEMOUNT; SIGNAL INPUT; Ex ia IIC T4 Ga; II 1 G; FIGURe 8. ATeX label Information

9 Instruction Sheet 5081C-HT LIQ_MAN_ABR_5081C-HT/Rev.G January 2015 9241505-00/F ROSEMOUNT ® ANALYTICAL Tamb = -20°C TO +65°C I.S. SUPPLY Ui = 30 VDC Ii = 200 mA Pi = 0.9 W Ci = 0 µF Li = 0 µH SIGNAL INPUT Uo = 6.51 V Io = 400 mA Po = 642 mW Ci = 24.1 µF Li = 0 µH 11 80 MODEL 5081-C-HT-73 IECExBAS0...

Page 10 - Figure 9. FMRC explosion-proof Installation

10 5081C-HT Instruction Sheet January 2015 LIQ_MAN_ABR_5081C-HT/Rev.G Figure 9. FMRC explosion-proof Installation

Page 11 - Figure 10. FM Hazardous Area Approval label

11 Instruction Sheet 5081C-HT LIQ_MAN_ABR_5081C-HT/Rev.G January 2015 Figure 10. FM Hazardous Area Approval label

Page 12 - Figure 11. FM Intrinsically Safe Installation

5 . D U ST -T IG H T C O N D U IT S EA L M U ST B E U SE D W H EN IN ST A LL ED IN C LA SS II A N D C LA SS II I E N V IR O N M EN TS . 6 . R ES IS TA N C E BE TW EE N IN TR IN SI C A LL Y SA FE G R O U N D A N D E A R TH G R O U N D M U ST B E LE SS T H A N 1 .0 O h m . 10 . T H E A SS O C IA TE D ...

Page 13 - Figure 12. CSA Hazardous Area Approval label

13 Instruction Sheet 5081C-HT LIQ_MAN_ABR_5081C-HT/Rev.G January 2015 Figure 12. CSA Hazardous Area Approval label

Page 14 - Figure 13. CSA Intrinsically Safe Installation

14 5081C-HT Instruction Sheet January 2015 LIQ_MAN_ABR_5081C-HT/Rev.G Figure 13. CSA Intrinsically Safe Installation

Page 15 - Engineering Specifications; To ReSeT TRANSMITeR To FACToRy deFAUlT

15 Instruction Sheet 5081C-HT LIQ_MAN_ABR_5081C-HT/Rev.G January 2015 Engineering Specifications qUICK-START 1. On the Remote, press PROG, NEXT, NEXT, ENTER.2. Use the arrow buttons to select Conduc (conductivity), rStvty (resistivity), or CuSt (custom curve) mode. Press ENTER. If you chose ConduC o...