Emerson 00825-0100-4593 - Manuals

Quick Installation Guide 00825-0100-4593, Rev BAJuly 2009 Rosemount 1151 5 S TEP 1 CONTINUED ... C. O-rings with Flange Adapters WARNING Whenever the flanges or adapters are removed, visually inspect the o-rings. Replace them if there are any signs of damage, such as nicks or cuts. If you replace th...

Quick Installation Guide 00825-0100-4593, Rev BA July 2009 Rosemount 1151 6 S TEP 2: C ONSIDER H OUSING R OTATION To improve field access or to better view the optional LCD display: 1. Loosen the housing lock nut. 2. Rotate the housing clockwise to the desired position – up to 90° from its original ...

Quick Installation Guide 00825-0100-4593, Rev BAJuly 2009 Rosemount 1151 7 S TEP 3: C ONNECT THE W IRING AND P OWER U P Use the following steps to wire the transmitter: 1. Remove the housing cover on the side marked TERMINALS on the nameplate. 2. Connect the positive lead to the “+” terminal and the...

Quick Installation Guide 00825-0100-4593, Rev BA July 2009 Rosemount 1151 8 S TEP 3 CONTINUED ... Power Supply The dc power supply should provide power with less than two percent ripple. The total resistance load is the sum of the resistance of the signal leads and the load resistance of the control...

Quick Installation Guide 00825-0100-4593, Rev BAJuly 2009 Rosemount 1151 9 S TEP 4: C ONFIGURE THE T RANSMITTER Failure Mode Alarm Switch 1. Remove the housing cover.2. Locate the failure mode switch (see Figure 3).3. Move the switch to the desired alarm setting. To set the failure mode to high alar...

Quick Installation Guide 00825-0100-4593, Rev BA July 2009 Rosemount 1151 10 S TEP 5: C ALIBRATE THE T RANSMITTER Verify Transmitter Configuration NOTE: A check ( ✓ ) indicates the basic configuration parameters. At minimum, these parameters should be verified as part of the configuration and startu...

Quick Installation Guide 00825-0100-4593, Rev BAJuly 2009 Rosemount 1151 11 S TEP 5 CONTINUED ... Configure LCD Display Figure 4. Sample 1151 LCD Display NOTE The LCD display time-out is approximately 16 seconds. If keys are not pressed within this period, the indicator reverts to reading the signal...

Quick Installation Guide 00825-0100-4593, Rev BA July 2009 Rosemount 1151 12 S TEP 5 CONTINUED ... Set the Display Equivalent to a 4 mA Signal 1. Unscrew the retaining ring shown in Figure 4 and remove the LCD display cover.2. Press the left button for two seconds.3. To decrement the display numbers...

Quick Installation Guide 00825-0100-4593, Rev BAJuly 2009 Rosemount 1151 13 S TEP 6: T RIM THE T RANSMITTER NOTE Transmitters are shipped fully calibrated per request or by the factory default of full scale (span = upper range limit). Full Trim A full trim is a two-point sensor calibration where two...

Quick Installation Guide 00825-0100-4593, Rev BAJuly 2009 Rosemount 1151 15 P RODUCT C ERTIFICATIONS Approved Manufacturing Locations Rosemount Inc. — Chanhassen, Minnesota, USAFisher-Rosemount GmbH & Co. — Wessling, GermanyEmerson Process Management Asia Pacific Private Limited — Singapore Beij...

Quick Installation Guide 00825-0100-4593, Rev BA July 2009 Rosemount 1151 16 Canadian Certifications Canadian Standards Association (CSA) Approvals E6 Explosion Proof for Class I, Division 1, Groups C and D; Class II, Division 1, Groups E, F, and G; Class III, Division 1 Hazardous Locations. Suitabl...

Quick Installation Guide 00825-0100-4593, Rev BAJuly 2009 Rosemount 1151 17 N1 ATEX Type N and Dust CertificationCertificate Number: BAS99ATEX3293XATEX Marking: II 3 GD Ex nL IIC T5 (-40 °C  T amb  40 °C) EX nL IIC T4 (-40 °C  T amb  80 °C) Dust Rating: T90 °C (T amb = -20 °C to 40 °C) Ui = 45 V...

Quick Installation Guide 00825-0100-4593, Rev BA July 2009 Rosemount 1151 18 N7 Type NCertificate Number: Aus Ex 122XEx n IIC T5 (T a = 80 °C) / T6 IP66 Special Conditions for safe use (x): 1. It is a condition of safe use that a nominal voltage of 30 V for Ex n application shall not be exceeded. 2....