Elektra Beckum DH 315 - Manuals

Page 2 - Great Britain

G Please return the enclosed warranty card to us. Retain proof of purchase! You are only entitled to claim warranty againstproof of purchase.Please see back cover for manufacturer representative´s address near-est you. Redaktion: Zindel • Technische Dokumentation und Multimedia • D-22417 Hamburg Gre...

Page 3 - Getting to know your planer

1 DH 315 Getting to know your planer DO WN UP DO WN UP 2 1 1 12 3 4 8 6 13 14 17 16 15 9 22 18 21 5 11 7 10 10 19 20 1 Carrying handles 2 Crank for thicknesser bed rise and fall 3 Workpiece thickness indicator 4 Planer bed 5 Screw plug for carbon brushes 6 Anti-kickback lock 7 Reset button 8 On/off ...

Page 4 - Read first; not; Safety information; Specified conditions of use; Please note in particular:

2 DH 315 Read first · Read these instructions before use Pay specialattention to the safety information. · If you notice transport damage whileunpacking, notify your supplier immediately. Do not operate the machine. · Dispose of the packing in an environmentallyfriendly manner. Take to a proper coll...

Page 5 - Safety devices; The anti-kickback lock must not be bent.; Operating controls; Reset button for overload relay

3 DH 315 Safety devices Anti-kickback lock (A) The anti-kickback lock prevents a workpiece beingthrown back against the operator by the rotatingcutterblock. The anti-kickback lock must not be bent. Cutterblock cover (B) The cutterblock cover prevents that the upper partof the cutterblock can be touc...

Page 6 - Installation and connection; Fixing the planer

4 DH 315 Installation and connection Fixing the planer To keep the machine from „wandering” by vibra-tions or from tipping over, it needs to be screwed toa workbench, workstand or similar support: 1. Drill four holes into the support. 2. Fit screws through holes from the top and secure from below wi...

Page 7 - Danger! Electrical Hazard; Operation; Entanglement hazard

5 DH 315 Assembling the knife setting gauge The setting gauge is necessary to install the cutterknives with the correct projection (1.5 mm). 1. Put a circlip to both inner spring ring grooves. 2. Slide a spacer block on each end of the shaft. 3. Fit a circlip to each of the outer spring ring groove....

Page 8 - Planing workpieces; Workpiece dimensions; Care and maintenance; Alignment of infeed and outfeed table

6 DH 315 Planing workpieces 3 The planer can remove max. 3 mm materialin one pass. This capacity, however, shallonly be utilized: - with very sharp planer knives; - with soft timber; - if the max. planing width is not utilized. Otherwise there is a risk of overloading themachine.It is best to make s...

Page 9 - Cutter knife replacement

7 DH 315 3. To align, fold infeed and outfeed table up and set the two each backstop setting screws(arrow) as required. Cutter knife replacement 3 Dull cutter knives are noticeable by - reduced performance; - increased risk of kickback; - stalling of the motor. A Danger!Risk of cut by the cutter kni...

Page 11 - Troubleshooting

9 DH 315 Machine transportation 1. Fold both infeed and outfeed table up. 2. Wind power cable around cable holder on the machine's side. Service plan Troubleshooting A Danger! Before carrying out any fault service ormaintenance work always: - Switch machine OFF. - Unplug power cable. - Wait until cu...

Page 12 - Technical specifications; Wiring diagram

10 DH 315 Technical specifications Wiring diagram Voltage V 230 ~ 50 Hz Min. fuse protection A 10 Motor capacity W 1500 Cutterblock no-load speed min -1 10.000 Feed rate m/min 8.0 Workpiece thickness min. max. mmmm 3153 Workpiece width min.max. mmmm 64318 Dimensions depth (folded up)widthheight mmmm...

Page 13 - Spare parts list

11 DH 315 Spare parts list Item Description Stock-no. 1 Handle 138 164 9225 2 Chain set 138 864 9280 3 Cutterblock bearing block 138 864 9271 4 Rubber roller 138 864 9263 5 Lock bar with screws 138 264 9253 6 Pressure springs (4-pc. set) 138 864 9247 7 Drive belt with belt disc 138 864 9239 8 Crank ...