Eiki LC-XA20 - Manuals

5 All the safety and operating instructions should be read before the product is operated. Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. Follow a...

Safety Instructions 6 Openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. CAUTION Hot air is exhausted from the exhaust vent. When using or installing the projector...

AC Power Cord for the United States and Canada: AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA). AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the p...

9 Part Names and Functions Part Names and Functions Part Names and Functions Rear Terminal q w e r t y u q SERVICE PORT This jack is used to service the projector. w COMPUTER IN /S-VIDEO IN /COMPONENT IN Connect output signal from a computer, RGB scart 1-pin video output, S-VIDEO output, or componen...

11 Part Names and Functions Part Names and Functions t e o !3 r !4 !2 !0 q w Remote Control y u i !5 !1 q POWER ON/STAND-By button Turn the projector on or off. (p.18, 19) w VIDEO button Select VIDEO input source. (p.3, 34) e COMPUTER button Select COMPUTER input source. (p.3, 5, 35) r MENU button O...

Part Names and Functions 1 To insure safe operation, please observe the following precautions: ● Use two () AA or LR6 type alkaline batteries. ● Always replace batteries in sets. ● Do not use a new battery with a used battery. ● Avoid contact with water or liquid. ● Do not expose the remote control ...

13 Installation ✔ Note: • The brightness in the room has a great influence on picture quality. It is recommended to limit ambient lighting in order to obtain the best image. • The values shown below are approximate and may vary from the actual sizes. Positioning the Projector A B 3.6' (9.9 m) 1.7' (...

Installation 15 Connecting to a Computer Cables used for connection • VGA Cables (Mini D-sub 15 pin) (Only one cable is supplied.) • Audio Cables (Mini Plug: stereo) ( Not all the cables are supplied with this projector.) Installation

Installation 16 Connecting to Video Equipment Cables used for connection • Video and Audio Cable (RCA x 3) • S-Video Cable • S-Video-VGA Cable • Audio Cables (RCA X 2, Mini Plug: stereo) ( Not all the cables are supplied with this projector.)

Installation 17 Installation Connecting to Component Video Equipment Cables used for connection • Audio Cables (Mini Plug :stereo) • Scart-VGA Cable • Component Cable • Component-VGA Cable ( Not all the cables are supplied with this projector.)

Basic Operation 18 Connect the projector's AC power cord into an AC outlet. The POWER indicator becomes red. Open the Lens Shutter by sliding the Lens Shutter Lever.(see page 8)Press the POWER ON/STAND-BY button on the top control or on the remote control. The POWER indicator becomes green and the c...

Basic Operation 19 Press the POWER ON/STAND-BY button on the top control or on the remote control, and a message "Power off?" appears on the screen.Press the POWER ON/STAND-BY button again to turn off the projector. The POWER indicator starts to blink red, and it continues while the cooling ...

Basic Operation 0 How to Operate the On-Screen Menu The projector can be adjusted or set via the On-Screen Menu. Refer to the following pages regarding each adjustment and setting procedures. Press the Point 7 8 buttons to select a Menu icon to adjust and press the Point ed buttons to select an item...

Basic Operation 1 Menu Bar PC System Menu Used to select computer system. (p.6) Setting Menu Used to set the projector's operating configurations. (p.41-50) Image Select Menu Used to select an image level among Dynamic, Standard, Real, Blackboard (Green), and Image 1 ~ 4. (p.30) For computer source ...

Basic Operation Press the ZOOM +/- buttons on the top control to adjust the screen size. Screen size can be adjusted 80% to 100% from it's maximum screen size. It is not available when On-Screen menu is displayed. Zoom adjustment can be memorized. (p.41) Zoom Adjustment Focus Ring If a projected pic...

Basic Operation 3 Press the VOLUME+/– buttons on the remote control to adjust the volume. The volume dialog box appears on the screen for a few seconds. Press the MUTE button on the remote control to cut off the sound. To restore the sound to its previous level, press the MUTE button again or press ...

Computer Input 5 Computer Input Choose Computer by pressing the INPUT button on the top control or press the COMPUTER button on the remote control. Before using these buttons, correct input source should be selected through Menu operation as described below. Input Source Selection Direct Operation I...

Computer Input 6 Computer System Selection This projector automatically tunes to various types of computers based on VGA, SVGA, XGA, SXGA, WXGA, or UXGA with its Multi-scan system and Auto PC Adjustment. If Computer is selected as a signal source, this projector automatically detects the signal form...

Computer Input 7 Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal, and Vertical to conform to your computer. Auto PC Adjustment function can be operated as follows. Auto PC Adjustment The Auto PC adjustment function can be operated directly by pressin...

Computer Input 8 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red framed pointer to the PC Adjust Menu icon. Press the Point ed buttons to move the red framed pointer to the item that you want to adjust and then press the SELECT button to display the a...

30 Computer Input Select an image level among Dynamic, Standard, Real, Blackboard (Green), Image 1, Image , Image 3, and Image 4 by pressing the IMAGE button on the remote control. Normal picture level preset on this projector. Picture level with improved halftone for graphics. Standard Real Image 1...

31 Computer Input Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red framed pointer to the Image Adjust Menu icon.Press the Point ed buttons to move the red framed pointer to the item that you want to adjust, and then press the SELECT button. The level o...

Computer Input 3 Store Exit the Image Adjust Menu. Quit To store the adjusted data, select Store and press the SELECT button. Select a level from Image 1 to 4 with the Point ed buttons and press the SELECT button. A confirmation box appears and then select [Yes]. Stored data can be called up by sele...

Computer Input 33 When the D.ZOOM + ( e ) is pressed, the On-Screen Menu disappears and the message "D. zoom +" is displayed. Press the D.ZOOM e or the SELECT button to expand the image size. And press the Point ed 7 8 buttons to pan the image. The Panning function can work only when the ima...

Video Input 34 Choose Video by pressing the INPUT button on the top control or the VIDEO button on the remote control. Before using these buttons, correct input source should be selected through menu operation as described below. Input Source Selection (Video) Direct Operation Video INPUT button Rem...

Video Input 36 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red framed pointer to the AV System Menu icon. Video System Selection Press the Point ed buttons to move the red arrow pointer to the system that you want to select and then press the SELECT b...

Video Input 38 Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red framed pointer to the Image Adjust Menu icon.Press the Point ed buttons to move the red framed pointer to the item that you want to adjust, and then press the SELECT button. The level of e...

Video Input 40 This projector has the picture screen resize function, which enables you to customize the image size. Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red framed pointer to the Screen Menu icon. Press the Point ed buttons and move the red fr...

Setting 41 Blue back Press the Point 7 8 buttons to switch On/Off. When this function is "On", a blue image is displayed while the input signal is not detected. Keystone Press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move the red framed pointer to the Set...

Setting 4 Display Press the Point 7 8 buttons to switch On/Off. This function decides to display On-Screen Displays. On. . . . . . . . . . . . . Show all the On-Screen Displays. Use this function when you want to project images after the lamp becomes bright enough. Factory default setting is this mo...

Setting 43 Capture This function enables you to capture the image being projected and use it for a start-up display or interval of presentations. After capturing the projected image, go to the Logo select function and set it to "User". Then the captured image is displayed when turning on the...

Setting 44 To Enter the Logo PIN code Select a number by pressing the Point ed buttons. And then press the Point 8 button to fix the number and move the pointer. The number changes to " ✳ ". If you fixed an incorrect number, move the pointer to the number you want to correct by pressing the ...

Setting 45 Ceiling When this function is "On", the picture is top/bottom and left/right reversed. This function is used to project the image from a ceiling mounting the projector. Rear When this function is "On", the picture is left/right reversed. This function is used to project th...

Setting 46 Power management F o r r e d u c i n g p o w e r c o n s u m p t i o n a s w e l l a s maintaining the lamp life, the Power management f u n c t i o n t u r n s o ff t h e p r o j e c t i o n l a m p w h e n t h e projector is not used for a certain period. When the input signal is interr...

Setting 48 Key lock Security (Key lock and PIN code lock settings) This function allows you to use Key lock and PIN code lock function to set the security for the projector operation. This function locks operation of the top control or the remote control. It is useful to prevent operation by an unau...

Setting 49 To Enter the PIN code Select a number by pressing the Point ed buttons. And then press the Point 8 button to fix the number and move the pointer. The number changes to " ✳ ". If you fixed an incorrect number, move the pointer to the number you want to correct by pressing the Point...

Setting 50 This function is used to reset the lamp replacement counter. When replacing the projection lamp, reset the lamp replacement counter by using this function. See page 55 for operation. Lamp counter Factory default This function returns all setting values except for the user logo, PIN code l...

Maintenance and Cleaning 51 The WARNING indicator shows the state of the function which protects the projector. Check the state of the WARNING indicator and the POWER indicator to take proper maintenance. Warning Indicator The projector is shut down and the WARNING indicator is blinking red . When t...

Maintenance and Cleaning 5 Turn off the projector, and disconnect the AC power cord from the AC outlet.Turn over the projector and remove the air filters by pulling the latches upward. Air filters prevent dust from accumulating on the optical elements inside the projector. Should the air filters bec...

Maintenance and Cleaning 53 Cleaning the Projector Cabinet Gently wipe the projector body with a soft, dry cleaning cloth. When it is heavily soiled, use a small amount of mild detergent and finish with a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner. Abrasive cleaners, solven...

Maintenance and Cleaning 55 Be sure to reset the Lamp replacement counter after the lamp is replaced. When the Lamp replacement counter is reset, the LAMP REPLACE indicator stops lighting. Turn the projector on, press the MENU button to display the On-Screen Menu. Press the Point 7 8 buttons to move...

Appendix 56 Troubleshooting Before calling your dealer or service center for assistance, check the items below once again. – Make sure you have properly connected the projector to peripheral equipment as described on pages15-17. – Make sure all equipment is connected to AC outlet and the power is tu...

Appendix 58 Menu Tree System (1) Mode 1Mode SVGA 1- - - - Computer Input ✽ Systems displayed in the System Menu vary depending on the input signal. Computer Input/Video Input Sound On/Off Sound 0 - 63 Input Computer ✽ N/A - - - not applicable RGB Go to System (1) N/A Quit RGB (Scart) Component Go to...

Appendix 60 Check the indicators for projector condition. Indicators and Projector Condition The projector is off. (The AC power cord is unplugged.) The projector is preparing for stand-by or the projection lamp is being cooled down. The projector cannot be turned on until cooling is completed. The ...

Appendix 61 Compatible Computer Specifications Basically this projector can accept the signal from all computers with the V, H-Frequency below mentioned and less than 140 MHz of Dot Clock. When selecting these modes, PC adjustment can be limited. MAC LC13 640 x 480 34.97 66.60 MAC 13 640 x 480 35.00...

Appendix 6 Technical Specifications Mechanical Information Projector Type Multi-media Projector Dimensions (W x H x D) 1.99" x 3.15" x 9.33" (330 mm x 80 mm x 37 mm) (Not including adjustable foot) Net Weight 6.4 lbs (.9 kg) Foot Adjustment 0˚ to 10.0˚ Panel Resolution LCD Panel System 0...

63 Appendix Accessories Owner's Manual (CD-ROM) Quick Reference Guide AC Power Cord Remote Control and Batteries VGA Cable PIN Code Label ● The specifications are subject to change without notice. ● LCD panels are manufactured to the highest possible standards. Even though 99.99% of the pixels are e...

64 Terminal: Mini DIN 8-PIN 1 3 4 5 8 7 6 SERVICE PORT CONNECTOR COMPUTER IN/S-VIDEO IN/COMPONENT IN/MONITOR OUT TERMINAL (ANALOG) Terminal : Analog RGB (Mini D-sub 15 pin) 5 1 2 3 4 10 9 6 7 8 15 14 13 11 12 Configurations of Terminals Red (R/Cr) Input/Output Ground (Horiz.sync.) Green (G/Y) Input/...

65 Appendix Appendix Write down the PIN code number in the column below and keep it with this manual securely. If you forgot or lost the number and unable to operate the projector, contact the service station. PIN Code Number Memo Factory default set No: 1 3 4* * Should the four-digit number be chan...

A-key to better communications U .S .A . EIKI International, Inc. 3051 Esperanza Rancho Santa Margarita CA 9688-13 U.S.A. Tel : 800-4-3454 (949)-457-000 Fax : 800-457-3454 (949)-457-7878 E-Mail : [email protected] Deutschland & Österreich EIKI Deutschland GmbH Am Frauwald 1 65510 Idstein Deutschland ...