Eiki EIP-X350 - Manuals

EN-6 Introduction Projector Features The projector integrates high-performance optical engine projection and a user-friendlydesign to deliver high reliability and ease of use. The projector offers the following features: Single chip 0.7" Texas Instruments DLP ® technology XGA (1024 x 768 pixels)...

EN-7 Package Contents When you unpack the projector, make sure you have all these components: Projector with Lens Cap AC Power Cord VGA Cable (D-SUB to D-SUB) Composite Video Cable Owner’s Manual Remote Control (IR) Laser Page up Page down Hide Resync Quick Start Guide AAA size batteries forremote c...

EN-8 Projector Over view Front View 1 Lens cap 2 Lens cap strap 3 Elevator foot 4 Front IR remote controlsensor 5 Elevator button 3 4 6 8 7 9 10 11 12 12 5 1 2 6 Projection lens 7 Focus ring 8 Tilt-adjustment foot 9 Control panel 10 Zoom ring 11 Speaker 12 Ventilation holes

EN-10 Using the Product Control Panel LED 1 Temp. (Temperature LED indicator) Refer to “LED Indicator Messages”. (p.30) 2 Lamp. (Lamp LED indicator) Refer to “LED Indicator Messages”. (p.30) 3 (Power LED indicator) Refer to “LED Indicator Messages”. (p.30) Button Function 3 Power Turns the projector...

EN-11 Terminals 1 Audio out Connects to a speaker or other audio input equipment. 2 USB This connector is for page up & down mouse control function and firmware update. 3 RS-232 When operating the projector via a computer, connect this to the controllingcomputer’s RS-232C port. 4 DVI Connects a ...

EN-12 Remote Control 1 Power Turns the projector on or off. (p.17) 2 Four directional buttons Use four directional buttons to selectitems or make adjustments to yourselection. (p.21) 3 MENU Opens the on-screen menu or acts onthe selected menu item. (p.21) 4 Laser Press and hold this button to activa...

EN-13 Installing the Batteries 1. Open the battery cover in the direction shown. 2. Install batteries as indicated by the diagram inside the compartment. 3. Close the battery cover into position. Keep the batteries out of the reach of children. There is a danger ofdeath by accidentally swallowing th...

EN-14 Ground Notes on AC Power Cord AC Power Cord must meet requirement of country where you use a projector. Confirman AC plug type with graphics below and proper AC Power Cord must be used. Ifsupplied AC Power Cord does not match your AC outlet, contact your sales dealer. Thisprojector is equipped...

EN-15 Remote Control Operation Point the remote control at the infrared remote sensor and press a button. Operating the projector from the front Operating the projector from the rear Do not point the laser pointer directly to the people's eyes (especiallysmall children). There is a danger of injuiry...

EN-16 Installation Connecting the Projector 1 USB Cable 6 Composite Video Cable 2 RS-232 Cable 7 VGA (D-Sub) to HDTV (RCA) Cable 3 DVI Cable 8 YPbPr Cable 4 VGA Cable (D-Sub to D-Sub) 9 Audio Cable 5 S-Video Cable Desktop type Laptop type 1 2 6 5 9 7 4 4 3 8 When connecting cable, power cords of bot...

EN-17 Powering On/Off the Projector Powering on the projector: 1. Remove the projector lens cap.2. Complete the AC power cord and peripheral signal cable(s) connections.3. Turn on the main power switch.4. The power LED indicator blinks blue in standby mode.5. Press button on the control panel or rem...

EN-18 Adjusting the Projector Adjusting the Projector Height The projector is equipped with an elevator foot and tilt-adjustment feet to adjust theimage height. 1. To raise or lower the image, press the elevator button and raise or lower the front of the projector. Release the button to lock the adj...

EN-19 Adjusting the Projector Zoom and Focus 1. Focus the image by rotating the focus ring. A still image is recommended for focusing. 2. Adjust the image by rotating the zoom ring. Rotate to the right to enlarge the image.Rotate to the left to reduce the image. Focus ring Zoom ring

EN-20 Position the projector in a horizontal position; other positions can causeheat build-up and damage to the projector.Make sure the heat ventilation holes are not blocked.Do not use the projector in a smoky environment. Smoke residue maycause buildup on critical parts. Adjusting Projection Image...

EN-21 Menu Operation The projector has multilingual on-screen display menus that allow you to make imageadjustments and change a variety of settings. How to operate 1. Press MENU to display the on-screen menu. 2. Press S / T to select any feature in the main menu, then press X to move into that menu...

EN-22 Setup Menu Keystone Adjusts image distortion caused by tilting projection. Reset keystone Resets the keystone correction to zero (no correction). Volume Adjusts the loudness of the projector’s audio. Mute Temporarily turns off the projector’s audio. Projector position Adjusts the picture to ma...

EN-23 Picture Menu Changing these settings affects only the active source. Some picture adjustments areavailable only when certain input ports are in use. Unavailable adjustments are shownin gray in the on-screen menu. Color settings Adjusts the image and colors. „ Brightness Brightens or darkens th...

EN-26 Turn off the projector and remove the AC power cord from the poweroutlet before beginning maintenance work.Make sure the lens is cool before cleaning.Do not use detergents or chemicals other than those noted above. Donot use benzene or thinners.Do not use chemical sprays.Use a soft cloth or le...

EN-27 Replacing the Lamp As the projector operates over time, the brightness of the projector lamp graduallydecreases and the lamp becomes more susceptible to breakage. We recommend replacingthe lamp if a warning message is displayed. „ The lamp becomes high temperature after turning off the project...

EN-29 Specifications Display Type Single 0.7" DLP panel Resolution (Pixels) XGA (1024 × 768) Lens Manual Zoom (1.2x)F=2.3~2.75 f=23.6~28.25mmThrow distance 1.2~10mScreen size 30inch ~300inch Contrast Ratio 2000:1 Uniformity >80% Lamp 300W Projection Type Front, Rear, Ceiling Input Source D-Su...

EN-30 Appendix LED Indicator Messages The projector is operating normally.Standby modeDuring shutdown cool-down.During flash update.Lamp failure.Ballast failure.Over-temperature error.During flash update.Fan, sensor, or color wheel error. Projector Condition Lamp --- Solid On Blinking - - Indicators...

EN-31 Compatibility Modes Computer: Compatibility Resolution H-Sync [KHz] V-Sync [Hz] VGA 640x480 31.469 59.940 640x480 37.861 72.809 640x480 37.500 75.000 640x480 43.269 85.008 SVGA 800x600 35.156 56.250 800x600 37.879 60.317 800x600 48.077 72.188 800x600 46.875 75.000 800x600 53.674 85.061 XGA 102...

EN-32 Troubleshooting Refer to the statement that most closely matches the nature of the problem beforesending the projector for repairs. If the problem persists, contact your local reseller orservice center.Please refer to “LED Indicator Messages” (p.30) as well. Problem: If no lights or sounds tur...