Page 2 - Setting up the Screen; Example of standard setup; Side View; o n t h e
2 For optimal image quality, position the projector perpendicular to the screen with the projector’s feet flatand level. Doing so will eliminate the need for Keystone correction and provide the best image quality. N o t e • The projector lens should be centered in the middle of the screen. If the ho...
Page 3 - Screen Size and Projection Distance; Throw Distance; Screen
3 Screen Size and Projection Distance The projection screen size varies according to the distance from the lens of the projector to the screen.The optional lenses from EIKI are also available for specialized application. Please see your nearest EIKIAuthorized Dealer to details on all the lenses. (Re...
Page 11 - pin female connector; Connecting Pin Assignments; 4 pin connector; HDMI Terminal
11 5 10 15 1 11 6 COMPUTER/COMPONENT input and COMPUTER/COMPONENT output Terminals: mini D-sub 15 pin female connector Connecting Pin Assignments RGB Input 1. Video input (red)2. Video input (green/sync on green)3. Video input (blue)4. Not connected5. Not connected6. Ear th (red)7. Ear th (green/syn...
Page 12 - D-sub 9 pin male connector
12 Connecting Pin Assignments RS-232C Terminal: D-sub 9 pin male connector Pin No. Signal Name I/O Reference 1 Not connected 2 RD Receive Data Input Connected to internal circuit 3 SD Send Data Output Connected to internal circuit 4 Not connected 5 SG Signal Ground Connected to internal circuit 6 No...
Page 13 - Wired Remote Control Terminal Specifications; EIKI remote control signal format; Transmission format:; Output using pulse position modulation; Transmission control code; Example of Reverse D to D
13 Specifications of wired remote control input ••••• ø3.5 mm minijack ••••• External: GND ••••• Internal: +3.3V Function and transmission codes Wired Remote Control Terminal Specifications C1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 C2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 C3 1 1 1...
Page 14 - Info; O K; RS-232C Specifications and Commands
14 Computer control A computer can be used to control the projector by connecting an RS-232C serial control cable (cross type,commercially available) to the projector. (See page 27 on the owner’s manual of the projector for connection.) Communication conditions Set the serial port settings of the co...
Page 15 - Commands; Example: When turning on the projector, make the following setting.
15 → ← P O W R _ 1 _ _ O K Projector Computer RS-232C Specifications and Commands CONTROL CONTENTS Power ON Standby mode (or 40-second startup time) COMMAND PARAMETER RETURN PPPT TTTTTTTTTTLLT M SP P P P IIIIIIIIII LLLLLLLL KKK I VV MM FFA RRRRRRR OOO A LL P LLLLLLL PPNNN J J J J RRRRVVRV M C NNNNNN...
Page 20 - Connecting the projector to a computer; Setting up the Projector Network Environment; Network settings on the computer; Setting an IP address for the computer
20 1. Connecting the projector to a computer Setting up the Projector Network Environment This section describes the basic procedure for using the projector via the network. If the network is already constructed, the projector’s network settings may need to be changed. Please consult your network ad...
Page 21 - jector to a Computer; Turn on the computer.; This completes the connection. Now proceed to; puter”
21 Setting up the Projector Network Environment 1. Connecting the Pro- jector to a Computer Establishing a one-to-one connection from theprojector to a computer. Using a commerciallyavailable LAN cable (UTP cable, Category 5,cross-over type) you can configure the pro-jector via the computer. 1 Disco...
Page 22 - Setting an IP Address
22 XXXXXXXXX Setting up the Projector Network Environment 2. Setting an IP Address for the Computer The following describes how to make settingsin Windows Vista ® . 1 Log on the network using theadministrator’s account for thecomputer. 2 Click “start”, and click “ControlPanel”. 3 Click “View network...
Page 23 - After confirming or setting, proceed to; “3. Setting up Network Connection for the Pro-
23 Setting up the Projector Network Environment 1 2 5 Click “Internet Protocol Version4 ( T C P / I P v 4 ) ” , a n d cl i ck t h e“Properties” button. 6 Confirm or change an IP addressfor the setup computer. 1 Confirm and note the current IP ad-dress, Subnet mask and Defaultgateway. Make sure to no...
Page 24 - Setting up a Network
24 Setting up the Projector Network Environment 3. Setting up a Network Connection for theProjector Settings for such items as the projector’s IPaddress and subnet mask are compatible withthe existing network.Set each item on the projector as follows. (Seepage 64 of the projector owner’s manual fors...
Page 25 - Click the “Apply” button.
25 Setting up the Projector Network Environment 4 The TCP/IP setting screen ap-pears, ready for network settingsfor the projector. N o t e • Confirm the existing network’s segment (IPaddress group) to avoid setting an IP ad-dress that duplicates the IP addresses ofother network equipment or computer...
Page 26 - Controlling the Projector via LAN; followed
26 Controlling the Projector via LAN Controlling the ProjectorUsing Internet Explorer (Version 5.0 or later) Complete connections to external equipmentbefore starting the operation. (See pages 24-27 of the projector owner’s manual.)Complete the AC cord connection. (See page28 of the projector owner’...
Page 27 - Controlling the Projector
27 Confirming the ProjectorStatus (Status) On this screen, you can confirm the projectorstatus. You can confirm the following items : ••••• MAC Address ••••• Power ••••• Condition ••••• Lamp Timer 1 ••••• Lamp Timer 2 ••••• Lamp Life 1 ••••• Lamp Life 2 ••••• Input ••••• Signal Info ••••• Serial Num...
Page 28 - Setting the Security
28 Controlling the Projector via LAN Setting and Adjusting theProjector (Settings & Adjustments) Example: “Picture” screen display for COMPUTER1 On these screens, you can make projectorsettings or adjustments. You can set or adjustthe following items : Setting the Security (Network – Security) O...
Page 31 - Setting the Projector Using RS-232C or Telnet
31 Setting the Projector Using RS-232C or Telnet When Connecting UsingRS-232C 1 Launch general purpose terminalemulator. 2 Input settings for the RS-232C portof the terminal emulator as follows. Baud Rate : 9600 bps* Data Length : 8 bit Parity Bit : None Stop Bit : 1 bit Flow Control : None * This i...
Page 32 - Click “start” from the Windows
32 Setting the Projector Using RS-232C or Telnet When Connecting UsingTelnet 1 Click “start” from the Windows ® desk- top and select “Run”. 2 Enter “telnet 192.168.150.2” in the textbox that opens up. (If the IP addressof the projector is 192.168.150.2.) 3 Click the “OK” button. 4 “User Name:” is di...
Page 33 - ADVANCED SETUP MENU
33 Setting the Projector Using RS-232C or Telnet SETUP MENU (Main Menu) [1] IP Address (Factory default setting : 192.168.150.2) IP address settings. (Page 36 ) [2] S u b n e t M a s k ( F a c t o r y d e f a u l t s e t t i n g : 255.255.255.0) Subnet mask settings. (Page 36 ) [3] Default Gateway (...
Page 34 - Controlling the Projector Using RS-232C or Telnet; View Setting Detail List; Set Items
34 Controlling the Projector Using RS-232C or Telnet View Setting Detail List ([V]View All Setting) 1 1 1 1 1 Enter “v” and press the “Enter” key. Display all setting values(*). Enter number or symbol of item to be selected on the SETUP MENU. When setting, input thedetails to be set. Setting is carr...
Page 35 - Save Settings and Quit
35 Controlling the Projector Using RS-232C or Telnet Save Settings and Quit ([S]Save & Quit) Save set values and quit menu. 1 1 1 1 1 Enter “s” and press the “Enter” key. 2 2 2 2 2 Enter “y” and press the “Enter” key. ▼ SETUP MENU ---------------------------------SETUP MENU----------------------...
Page 36 - IP Address Setting; Subnet Mask Setting; Default Gateway Setting; User Name Setting
36 Controlling the Projector Using RS-232C or Telnet IP Address Setting ([1]IP Address) Setting of IP address. 1 1 1 1 1 Enter “1” and press the “Enter” key. 2 2 2 2 2 Enter numerical value to be set and press the“Enter” key. Display IP address after change (*). Subnet Mask Setting ([2]Subnet Mask) ...
Page 37 - Password Setting; Projector Name Setting; DHCP Client Setting
37 Controlling the Projector Using RS-232C or Telnet Password Setting ([5]Password) Carrying out security protection using password. 1 1 1 1 1 Enter “5” and press the “Enter” key. 2 2 2 2 2 Enter password and press the “Enter” key. Display set password (*). N o t e • Password can be up to 8 characte...
Page 38 - Setting Auto Logout Time; Data Port Setting
38 Controlling the Projector Using RS-232C or Telnet Disconnecting All Connec-tions ([D]Disconnect All) It is possible to disconnect all the TCP/IP connec-tions currently recognized by the projector. Even ifthe COM Redirect port is fixed in the Busy statusdue to a problem, it is possible to force th...
Page 39 - Accepting All IP Addresses
39 Controlling the Projector Using RS-232C or Telnet Carrying out Network PingTest (ADVANCED[5]Network Ping Test) It is possible to confirm that a network connectionbetween the projector and a computer etc. is work-ing normally. 1 1 1 1 1 Enter “5” and press the “Enter” key. 2 2 2 2 2 Enter IP addre...
Page 40 - Setting of Search Port; Return to Default Settings; Return to Main Menu
40 Controlling the Projector Using RS-232C or Telnet Setting of Search Port (ADVANCED[0]Search Port) Sets the port number used when searching for theprojector from the network. 1 1 1 1 1 Enter “0” and press the “Enter” key. 2 2 2 2 2 Enter numerical value and press the “Enter” key. Display set numer...
Page 41 - Stack Projection
41 Stack Projection The stack projection allows you to increase the brightness of an image by stacking twoprojectors and projecting same image simultaneously. Info • To set up the stack projection, assign a projector as the master and the other projector as the slave andconnect the projectors with c...
Page 42 - Setting up the Stack Projection; Basic; Turn off the both projectors.; Master; Slave; Projector 1
42 Stack Projection Setting up the Stack Projection Basic This part shows an example for setting up the stack projection of a computer image with two projectors. Projector 1: Master Projector 2: Slave RGB cable RGBcable MONITOR OUT (FOR COMPUTER/ COMPONENT1, 2) terminal COMPUTER/COMPONENT1 terminal ...
Page 43 - Application
43 Stack Projection Projector 1: Master Projector 2: Slave Video equipment Distributor RGB cable 5BNC to mini D-sub 15 pincable Composite video cable RGBcable MONITOR OUT (FOR COMPUTER/ COMPONENT1, 2) terminal COMPUTER/COMPONENT1 terminal COMPUTER/COMPONENT1 terminal COMPUTER/COMPONENT2 terminal VID...
Page 44 - Video Wall Projection
44 Video Wall Projection Info • Before setting up the video wall projection, install Internet Explorer (version 5.0 or later). • Video wall is not compatible with resolutions higher than SXGA. • Image quality may deteriorate when picture signals are input through multiple projectors with an RGBcable...
Page 45 - Video Wall Projection; Setting up the Video Wall Projection Basic
45 Video Wall Projection Setting up the Video Wall Projection Basic Following is an example of how to build a 2 X 2 video wall using 4 projectors. Projector 1 Projector 2 Projector 3 Projector 4 COMPUTER/COMPONENT1 terminal RGB cable RGB cable RGB cable RGB cable MONITOR OUT (FOR COMPUTER/COMPONENT1...
Page 46 - Click “Video Wall” on the menu.; Select “2 X 2” on “Division”.
46 Video Wall Projection 1 Access one of the four projectorsvia Internet Explorer. (See “Controlling the Projector Using InternetExplorer (Version 5.0 or later)” (page 26 ) for the details.) 2 Click “Video Wall” on the menu. • “Video Wall” display will appear. 3 Select “2 X 2” on “Division”. 1 2 3 4...
Page 47 - Assigning the Projected Image on the Video Wall Setup; Front Projection; Select “1 X 1” on “Division”.
47 Video Wall Projection The numbers of the projector refer to the numbersof the projected positions. 1 2 2 3 3 4 5 5 5 6 7 8 9 1 2 3 4 5 6 7 8 9 2 The numbers of the projector refer to the numbersof the projected positions. 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 Assigning the Projected Image on the Vi...
Page 48 - Notes on the Wide Video Wall Projection
48 Video Wall Projection Notes on the Wide Video Wall Projection Selecting “2 X 1”, “3 X 1”, “4 X1”, “5 X 1”, “6 X 1”, “7 X 1” or “8 X 1” on “Division” (see page 46 ) allows you to create the wide video wall. To create the wide video wall with three projectors lining up in single file from left to r...
Page 49 - Setting up the Video Wall Projection Application
49 Video Wall Projection Projector 1 : Master Projector 2 : Slave Projector 3: Slave Projector 4 : Slave RGB cable 5BNC to mini D-sub 15 pin cable RGBcable RGBcable RGBcable LAN terminal VIDEO terminal COMPUTER/COMPONENT2 terminal MONITOR OUT (FOR COMPUTER/COMPONENT1, 2) terminal LAN terminal LAN te...
Page 50 - Preparation; Follow the procedure below after setting up the basic connection.
50 Video Wall Projection Projector 1: Master Projector 2: Slave Projector 3: Slave Projector 4: Slave LAN terminal LAN terminal LAN terminal LAN terminal LAN cable LAN cable(straight-through type) Hub Computer 1 Change the TCP/IP settings for thecomputer as shown below. (See “Setting an IP Address f...
Page 52 - Turn off all of the projectors.
52 Video Wall Projection Master Set Inputs ON ON OFF OFF ON OFF ON OFF OFF OFF ON OFF Slave Set Inputs COMPUTER1COMPUTER2 DVI HDMI VIDEO S-VIDEO COMPUTER1COMPUTER2 DVI HDMI VIDEO S-VIDEO Projector 1 Projector 2-4 13 Repeat the same procedure fromthe step 10 to 12 for the projector 3and 4. 14 Select ...
Page 53 - Resetting the Lamp Timer of the Projector via LAN; ating system. When you use Windows Vista
53 1 Click “Start” – “All Programs” –“Accessories” – “Communica-tions” – “HyperTerminal”. • If you do not have HyperTerminal in-stalled, see the owner ’s manual of yourcomputer. • Depending on the settings of your com-puter, you may be required to enter yourarea code and other details. Enter theinfo...
Page 55 - Communication cannot be established with the projector; When connecting the projector using serial-connection; Check the network settings for the computer and the projector; Troubleshooting
55 Communication cannot be established with the projector When connecting the projector using serial-connection \ Check that the RS-232C terminal of the projector and a computer or the commerciallyavailable controller are connected correctly. \ Check that the RS-232C cable is a cross-over cable. \ C...
Page 58 - Dimensions
58 Dimensions Units: inches (mm) Side View Side View Top View Rear View Front View Bottom View M6 M6 M6 M6 21 15 / 16 (557) 12 11 / 64 (309) 5 7 / 8 (149) 2 41 / 64 (67) 11 61 / 64 (303.5) 8 19 / 64 (210.5) 2 39 / 64 (66) 3 5 / 64 (78) 1 31 / 32 (50) 6 5 / 32 (156) 6 41 / 64 (168.5) 21 / 64 (8) 19 1...
Page 59 - Projector and Lens Dimensions
59 Dimensions Projector and Lens Dimensions [When AH-55201 is installed] [When AH-55301 is installed] [When AH-55401 is installed] 25 3 / 32 (637) 3 57 / 64 (98.5) 2 29 / 32 (73.6) Lens center 25 3 / 32 (637) Lens center 1 27 / 32 (46.7) 3 / 64 (1) 3 57 / 64 (98.5) 25 3 / 32 (637) Lens center 1 / 16...
Eiki 3279A
Manual
Eiki LC-XB40
Manual
Eiki LC-XIP2000
Manual
Eiki LC-X71L
Manual
Eiki LC-XGA982U
Manual
Eiki EIP-2500
Manual
Eiki LC-X3L
Manual
Eiki LC-SB20
Manual
Eiki AH-45501
Manual
Eiki LC-7000
Manual
Eiki LC-SM3
Manual
Eiki LC-X984
Manual
Eiki 8080A
Manual
Eiki OHP-4100
Manual
Eiki LC-SX6A
Manual
Eiki LC-X1000
Manual
Eiki LC-XNB5M
Manual
Eiki LC-X60
Manual
Eiki OHP-4100A
Manual
Eiki LC-X7
Manual